Freescale QE UDC controllers can't report the "port change" states,
so the only way to handle disconnects is to process bus reset
interrupts. The bus reset can take some time, that is, few irqs.
Gadgets may print the disconnection events, and this causes few
repetitive messages in the kernel log.
This patch fixes the issue by using the usb_state machine, if the
usb controller has been already reset, just quit the reset irq
early.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qe_udc_reg_init() leaves the USB controller enabled before muram memory
initialized. Sometimes the uninitialized muram memory confuses the
controller, and it start sending the busy interrupts.
Fix this by disabling the controller, it will be enabled later by
the gadget driver, at bind time.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The call chain is this:
qe_udc_irq() <- grabs the udc->lock spinlock
rx_irq()
qe_ep0_rx()
ep0_setup_handle()
setup_received_handle()
ch9getstatus()
qe_ep_queue() <- tries to grab the udc->lock again
It seems unsafe to temporarily drop the lock in the ch9getstatus(),
so to fix that bug the lock-less __qe_ep_queue() function
implemented and used by the ch9getstatus().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case of probing errors the driver kfrees the udc_controller, but it
doesn't set the pointer to NULL.
When usb_gadget_register_driver is called, it checks for udc_controller
!= NULL, the check passes and the driver accesses nonexistent memory.
Fix this by setting udc_controller to NULL in case of errors.
While at it, also implement irq_of_parse_and_map()'s failure and cleanup
cases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.
Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.
At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
! has a higher precedence than &
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another Conexant, another device with the same quirk
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).
This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: Marcel Sebek <sebek64@post.cz>
Acked-by: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: Jean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0
It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.
This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson <eu@mhayk.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: Robie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,
PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c
From: Tomasz K <eros81@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?
output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):
before patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)
after patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0
Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.
Signed-off-by: stephen ware <stephen.ware@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.
I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.
From: James A. Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.
This patch fixes this issue.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies. This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initializes the actual_len field to 0 before every DMA transaction.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:
drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h:
No such file or directory
drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h:
No such file or directory
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes insert module failure as free_irq() was not
done in previous rmmod.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trying once more to get this merged. The original was submitted
for 2.6.27-rc2 or so, and never got correctly merged. Neither
were any of the numerous subsequent resends. Sigh.
CC drivers/usb/musb/davinci.o
drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory
drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory
drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory
drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode'
drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> > drivers/built-in.o: In function `ohci_omap_init':
> > hid-quirks.c:(.text+0x6c608): undefined reference to `otg_get_transceiver'
> > drivers/built-in.o: In function `omap_udc_probe':
> > hid-quirks.c:(.init.text+0x34c0): undefined reference to `otg_get_transceiver'
> > hid-quirks.c:(.init.text+0x3d40): undefined reference to `otg_put_transceiver'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1198) fixes a conceptual bug: Somewhere along the line
we managed to confuse USB class devices with USB char devices. As a
result, the code to send a disconnect signal to userspace would not be
built if both CONFIG_USB_DEVICE_CLASS and CONFIG_USB_DEVICEFS were
disabled.
The usb_fs_classdev_common_remove() routine has been renamed to
usbdev_remove() and it is now called whenever any USB device is
removed, not just when a class device is unregistered. The notifier
registration and unregistration calls are no longer conditionally
compiled. And since the common removal code will always be called as
part of the char device interface, there's no need to call it again as
part of the usbfs interface; thus the invocation of
usb_fs_classdev_common_remove() has been taken out of
usbfs_remove_device().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Alon Bar-Lev <alon.barlev@gmail.com>
Tested-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: stable <stable@kernel.org>
Commit a0d4922da2
(USB: fix up suspend and resume for PCI host controllers) attempted
to fix the suspend-resume of PCI USB controllers, but unfortunately
it did that incorrectly and interrupts are left enabled by the USB
controllers' ->suspend_late() callback as a result. This leads to
serious problems during suspend which are very difficult to debug.
Fix the issue by removing the ->suspend_late() callback of PCI
USB controllers and moving the code from there to the ->suspend()
callback executed with interrupts enabled. Additionally, make
the ->resume() callback of PCI USB controllers execute
pci_enable_wake(dev, PCI_D0, false) to disable wake-up from the
full power state (PCI_D0).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: "Jeff Chua" <jeff.chua.linux@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Zdenek Kabelac" <zdenek.kabelac@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1199) changes the initial wakeup settings for PCI USB
host controllers. The controllers are marked as capable of waking the
system, but wakeup is not enabled by default.
It turns out that enabling wakeup for USB host controllers has a lot
of bad consequences. As the simplest example, if a USB mouse or
keyboard is unplugged immediately after the computer is put to sleep,
the unplug will cause the system to wake back up again! We are better
off marking them as wakeup-capable and leaving wakeup disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an unusual devs entry for 2116:0320
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1200) finishes some fixes that were left incomplete by
an earlier patch.
Although nobody has addressed this issue in the past, it turns out
that we need to distinguish between two different modes of disabling
and enabling endpoints. In one mode only the data structures in
usbcore are affected, and in the other mode the host controller and
device hardware states are affected as well.
The earlier patch added an extra argument to the routines in the
enable_endpoint pathways to reflect this difference. This patch adds
corresponding arguments to the disable_endpoint pathways. Without
this change, the endpoint toggle state can get out of sync between
the host and the device. The exact mechanism depends on the details
of the host controller (whether or not it stores its own copy of the
toggle values).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Streetman <ddstreet@ieee.org>
Tested-by: Dan Streetman <ddstreet@ieee.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor/product ID of the fasttrax GPS evaluation kit from:
http://www.fastraxgps.com/products/evaluationtools/evaluationkit/
to the cp2101 module since this device is actually equipped with a
CP210x USB to serial bridge.
The vendor/product ID is: 0x10c4/0x826b.
Signed-off-by: Wolfgang Glas <wolfgang.glas@ev-i.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Carry out the PM-routine interface change in the USB OTG pathway. This
was omitted from the earlier interface-change patch by mistake.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4a90f09b20 added kref stuff to
ftdi_sio, but missed tty_kref_put at one exit point in
ftdi_process_read.
Signed-off-by: Jim Paris <jim@jtan.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the Multi-Tech cellular modem firmware to the TI USB serial driver.
This firmware was extracted from:
ftp://ftp.multitech.com/wireless/wireless_linux.zip
Firmware licence: "all firmware components are redistributable in binary
form" per support@multitech.com
Copyright (C) 2005 Multi-Tech Systems, Inc.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Multi-Tech cellular modem support to the ti_usb_3410_5052 driver.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TI USB serial driver supports specifying alternate vendor and
product IDs (since the chips can and are used in devices under other
vendor/product IDs). However, the alternate IDs were not loaded in the
combined product table. This patch also adds support for loading
alternate firmware for alternate vendor/product IDs.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawell found a case where a NULL check was misplaced in the
usb-serial code. However as the object in question cannot be NULL the
check can simply be removed.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver got rescued from a few years ago and was requested to be
added. So I cleaned it up, ported it to the latest kernel version and
here it is.
Cc: Thomas Hergenhahn <thomas.hergenhahn@suse.de>
Cc: Emmanuele <iemmav@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb gadget framework revealed weakness in the godu_udc
gadget driver register function. Instead of checking if
speed asked for was USB_LOW_SPEED upon usb_gadget_register()
to deny service, it checked only for USB_FULL_SPEED, thus
denying service to usb high speed capable gadgets.
Signed-off-by: SangSu Park <sangsu@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One minor nit did show up, though. The patch below
seems to make more sense than the code does without it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1197) fixes an error introduced recently. Since a
significant number of devices can't handle Set-Interface requests, we
no longer call usb_set_interface() when a driver unbinds from an
interface, provided the interface is already in altsetting 0. However
the interface still does get disabled, and the call to
usb_set_interface() was the only thing re-enabling it. Since the
interface doesn't get re-enabled, further attempts to use it fail.
So the patch adds a call to usb_enable_interface() when a driver
unbinds and the interface is in altsetting 0. For this to work
right, the interface's endpoints have to be re-enabled but their
toggles have to be left alone. Therefore an additional argument is
added to usb_enable_endpoint() and usb_enable_interface(), a flag
indicating whether or not the endpoint toggles should be reset.
This is a forward-ported version of a patch which fixes Bugzilla
#12301.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Roka <roka@dawid.hu>
Reported-by: Erik Ekman <erik@kryo.se>
Tested-by: Erik Ekman <erik@kryo.se>
Tested-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1195) eliminates a potential problem identified by
Oliver Neukum. When a driver queues an asynchronous Set-Config
request using usb_driver_set_configuration(), the request should be
cancelled if userspace changes the configuration first. The patch
introduces a linked list of pending async Set-Config requests, and
uses it to invalidate the requests for a particular device whenever
that device's configuration is set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1193b) enables wakeup during initialization for all PCI
host controllers, and it removes some code (and comments!) that are no
longer needed now that the PCI core automatically initializes wakeup
settings for all new devices.
The idea is that the bus should initialize wakeup, and the bus glue
or controller driver should enable it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1192) rearranges the USB PCI host controller suspend and
resume and resume routines:
Use pci_wake_from_d3() for enabling and disabling wakeup,
instead of pci_enable_wake().
Carry out the actual state change while interrupts are
disabled.
Change the order of the preparations to agree with the
general recommendation for PCI devices, instead of
messing around with the wakeup settings while the device
is in D3.
In .suspend:
Call the underlying driver to disable IRQ
generation;
pci_wake_from_d3(device_may_wakeup());
pci_disable_device();
In .suspend_late:
pci_save_state();
pci_set_power_state(D3hot);
(for PPC_PMAC) Disable ASIC clocks
In .resume_early:
(for PPC_PMAC) Enable ASIC clocks
pci_set_power_state(D0);
pci_restore_state();
In .resume:
pci_enable_device();
pci_set_master();
pci_wake_from_d3(0);
Call the underlying driver to reenable IRQ
generation
Add the necessary .suspend_late and .resume_early method
pointers to the PCI host controller drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1194) makes usb-storage set the CAPACITY_HEURISTICS flag
for all devices made by Nokia, Nikon, or Motorola. These companies
seem to include the READ CAPACITY bug in all of their devices.
Since cell phones and digital cameras rely on flash storage, which
always has an even number of sectors, setting CAPACITY_HEURISTICS
shouldn't cause any problems. Not even if the companies wise up and
start making devices without the bug.
A large number of unusual_devs entries are now unnecessary, so the
patch removes them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1190) makes usb-storage's "quirks=" module parameter
writable, so that users can add entries for their devices at runtime
with no need to reboot or reload usb-storage.
New codes are added for the SANE_SENSE, CAPACITY_HEURISTICS, and
CAPACITY_OK flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1189b) adds some hacks to usb-storage for dealing with
the growing problems involving bad capacity values and last-sector
accesses:
A new flag, US_FL_CAPACITY_OK, is created to indicate that
the device is known to report its capacity correctly. An
unusual_devs entry for Linux's own File-backed Storage Gadget
is added with this flag set, since g_file_storage always
reports the correct capacity and since the capacity need
not be even (it is determined by the size of the backing
file).
An entry in unusual_devs.h which has only the CAPACITY_OK
flag set shouldn't prejudice libusual, since the device will
work perfectly well with either usb-storage or ub. So a
new macro, COMPLIANT_DEV, is added to let libusual know
about these entries.
When a last-sector access succeeds and the total number of
sectors is odd (the unexpected case, in which guessing that
the number is even might cause trouble), a WARN is triggered.
The kerneloops.org project will collect these warnings,
allowing us to add CAPACITY_OK flags for the devices in
question before implementing the default-to-even heuristic.
If users want to prevent the stack dump produced by the WARN,
they can disable the hack by adding an unusual_devs entry
for their device with the CAPACITY_OK flag.
When a last-sector access fails three times in a row and
neither the FIX_CAPACITY nor the CAPACITY_OK flag is set,
we assume the last-sector bug is present. We replace the
existing status and sense data with values that will cause
the SCSI core to fail the access immediately rather than
retry indefinitely. This should fix the difficulties
people have been having with Nokia phones.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add driver for the high speed USB-OTG transceiver in TI's TWL4030
family of chips.
Given this and various other pending patches, OMAP3 hardware like
that from beagleboard.org, gumstix.com (Overo), and openpandora.org
should now have basic USB host and peripheral connectivity with
mainline kernels. Ditto for less widely-available boards.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implementation of USB device driver integrated in Freescale's i.MXL
processor.
Adds USB device driver for i.MXL.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This extension allows unpoisoning an anchor allowing drivers that
resubmit URBs to reuse an anchor for methods like resume()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to disable port 1 on ISP1761. That port could
be used as an OTG port which would require a different init
sequence. However we don't have OTG support (yet) so we can use
it as a normal USB port.
This patch allows port 1 to be used a normal Port on the ISP1761.
Signed-off-by: Thomas Hommel <Thomas.Hommel@gefanuc.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many newer Option mobile broadband devices initially provide a
usb-storage "driver CD" device that's pretty useless on Linux since
any software on it most likely wouldn't be compatible with your
kernel or distro anyway. Thus, by default just kill the driver
CD device by sending the SCSI 'rezero' command, but allow override
of the default behavior via usb-storage module parameter so users
can keep the ZeroCD device if they really want to. Inspired by
the Sierra TruInstall patch.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Peter Henn <p.henn@option.com
Cc: Denis Joseph Barrow <D.Barow@option.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is enough to protect accesses to reject field of urb
by marking it as atomic_t,also it is the only reason of
existence of usb_reject_lock,so remove the lock to make
code more clean.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1185) makes usbcore take advantage of the bus
notifications sent out by the driver core. Now we can create all our
device and interface attribute files before the device or interface
uevent is broadcast.
A side effect is that we no longer create the endpoint "pseudo"
devices at the same time as a device or interface is registered -- it
seems like a bad idea to try registering an endpoint before the
registration of its parent is complete. So the routines for creating
and removing endpoint devices have been split out and renamed, and
they are called explicitly when needed. A new bitflag is used for
keeping track of whether or not the interface's endpoint devices have
been created, since (just as with the interface attributes) they vary
with the altsetting and hence can be changed at random times.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: make printk messages more searchable
Make USB printk messages long and straightforward. One of these
decorated USB error messages cost me non-trivial efforts to locate.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some config registers are not avaiable in Blackfin, we have to comment them out.
v1-v2:
- remove Blackfin specific header file
- add Blackfin register version to musb_regs.h header file
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- DMA registers in Blackfin have different layout
- DMA interrupt flags need to be cleared by software
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure we program the correct values in only when necessary.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- replace MUSB_FIFOSIZE register to MUSB_TXCOUNT, cause no MUSB_FIFOSIZE
register on Blackfin
- use #ifdef to replace #if defined()
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DPCM subdriver is a little peculiar, in that it's meant to support
devices where LUN 0 is Compact Flash and uses the CB transport whereas
LUN 1 is SmartMedia and uses the SDDR09 transport. Thus DPCM isn't
really a transport in itself; it's more like a demultiplexer.
Much of the DPCM code is part of the SDDR09 subdriver already, and the
remaining part is fairly small. This patch (as1182) moves that extra
piece into sddr09.c, thereby eliminating dpcm.c. Also eliminated is
the Kconfig entry for DPCM support; it is now listed as part of the
SDDR09 entry.
In order to make sure that the semantics are the same as before, each
unusual_devs entry for DPCM is now present twice: once with DPCM
support if SDDR09 is configured (as before), and once with the
SINGLE_LUN flag and CB support otherwise.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This should speed up the option driver's upload speed quite a bit. It has been tested by a number of different people on different devices with success.
Cc: Roland Wolters <roland.wolters@credativ.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the usb-serial drivers are starting to use urb->status in ways
they should not be doing. This fixes up some of them to prevent that.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Contains fixes so probe on x86 PCI runs, apparently I'm first to try
this. Several fixes to memory access to probe host scratch register.
Previously would bug check on chip_addr var used uninitialized.
Scratch reg write failed in one instance due to 16-bit initial access
mode, so added "& 0x0000ffff" to the readl as fix.
Includes some general cleanup - remove global vars, organize memory map
resource use.
Signed-off-by: Karl Bongers <kbongers@jged.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver can't handle (of course) any brdige class devices. So we
now are just active on one specific bridge which should be only the
isp1761 chip behind a PLX bridge.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Karl Bongers <kblists08@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some obscure scenarios e.g. passing a 0-byte backing file
storage, wait_for_completion() would wait forever in fsg_cleanup().
Prevent it by completing the thread in fsg_bind() error path.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1177) modifies the USB core suspend and resume
routines. The resume functions now will take a pm_message_t argument,
so they will know what sort of resume is occurring. The new argument
is also passed to the port suspend/resume and bus suspend/resume
routines (although they don't use it for anything but debugging).
In addition, special pm_message_t values are used for user-initiated,
device-initiated (i.e., remote wakeup), and automatic suspend/resume.
By testing these values, drivers can tell whether or not a particular
suspend was an autosuspend. Unfortunately, they can't do the same for
resumes -- not until the pm_message_t argument is also passed to the
drivers' resume methods. That will require a bigger change.
IMO, the whole Power Management framework should have been set up this
way in the first place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1178) uses the new round_jiffies_up_relative() routine
for setting the autosuspend delayed_work timer. It's appropriate
since we don't care too much about the exact length of the delay, but
we don't want it to be too short (rounded down).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move otg_get/set/put_transceiver() from omap specific code
to common otg.c so other upcoming drivers can share them.
[ dbrownell@users.sourceforge.net: move to drivers/usb/otg, dox ]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Russell King points out, calling put_device(otg_transceiver->dev)
directly in driver cleanup paths makes assumptions about otg_transceiver
internals.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gpio_vbus provides simple GPIO VBUS sensing for peripheral
controllers with an internal transceiver.
Optionally, a second GPIO can be used to control D+ pullup.
It also interfaces with the regulator framework to limit charging
currents when powered via USB. gpio_vbus requests the regulator
supplying "vbus_draw" and can enable/disable it or limit its
current depending on USB state.
[dbrownell@users.sourceforge.net: use drivers/otg, cleanups ]
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the isp1301-omap driver from the drivers/i2c/chips
directory (which will be shrinking) into a new drivers/usb/otg
directory (which will grow, with more drivers and utilities).
Note that OTG infrastructure needs to be initialized before
either host or peripheral side USB support, and may be needed
before for pure host or pure peripheral configurations.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the gpio code in the s3c2410_udc to use the
generic gpio calls instead of the s3c24xx specific
gpio functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some code in the pxa25x_udc driver wrongly expects the value
of is_vbus_present() to be 0/1, not zero/nonzero ... cope.
Issue noted by Jaya Kumar <jayakumar.lkml@gmail.com>
This bug has been around since July 2007, and has a simple
workaround: unplug the Linux gadget, then re-plug it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without it, in platforms that don't provide irq_chip.set_wake(),
like omap, musb will WARN() on driver removal.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Random host-side MUSB updates, mostly relating to better diagnostics:
+ Improve diagnostics on host side:
- tx flush fifo:
* Avoid hundreds of duplicate TX FIFONOTEMPTY messages
* make "Can't flush TX fifo" a warning, and say which endpoint
- giveback:
* use correct status code
* show completion function name not just URB pointer
- Fix annoying "1 bytes" (should be "1 byte")
+ Be more consistent about failing init of unusable fifo_mode
It's not clear why that "can't flush TX fifo" message appears, though
it might relate to disconnection; I see it not infrequently
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor locking fix for musb_hdrc on OMAP3 and OMAP2430:
don't read DEVCTL without holding the spinlock, since
an IRQ could come in and corrupt things.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix three omissions in the "mode" sysfs attribute support:
(a) inability to report errors;
(b) no DaVinci support ... just report an error;
(c) for omap2430, accepting unsupportable values
The 2430 stuff is still odd....
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MIPS USB IP core family device controller
Currently it only supports IP part number CI13412.
[dbrownell@users.sourceforge.net: minor comment tweaks]
Signed-off-by: David Lopo <dlopo@chipidea.mips.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since num is unsigned, it would seem better to use simple_strtoul that
simple_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r2@
long e;
position p;
@@
e = simple_strtol@p(...)
@@
position p != r2.p;
type T;
T e;
@@
e =
- simple_strtol@p
+ simple_strtoul
(...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Impact: cleanup
Found this when I changed args to __module_param_call. We now have
core_param for exactly this, but Greg assures me "nousb" is used as a
module parameter, so we need the #ifdef MODULE.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1175) makes usb-storage set a SCSI device's
request-queue bounce limit such that all buffers will be located in
addressable memory (i.e., not in high memory) if the host controller's
dma_mask is NULL. This is necessary when the host controller doesn't
support DMA: If a buffer is in high memory then the both the virtual
and DMA addresses produced by the scatter-gather library will be NULL,
preventing the HCD from accessing the buffer's data.
In particular, the isp1760 driver needs this when used on a system
with more than 1 GB of memory.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Tested-by: Thomas Hommel <Thomas.Hommel@gefanuc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1174) merges usb-storage's QIC-157 and ATAPI protocol
routines. Since the two functions are identical, there's no reason to
keep them separate.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1173) merges usb-storage's CB and CBI transports into a
single routine. So much of their code is common, it's silly to keep
them separate.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1172) adds the ability to emulate a CD-ROM drive to
g_file_storage. The emulation is limited, since it presents as a disc
containing a single data track and no audio tracks. Still, it may
come in useful on occasion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a few devices known to have support for larger sense buffers.
Supporting SANE_SENSE does not necessarily mean SAT-1 or SAT-2 is fully
supported.
Depends on SANE_SENSE patch [1]. Incorporates the Maxtor and Western
Digital devices originally submitted by Matthieu CASTET [2].
[1] https://lists.one-eyed-alien.net/pipermail/usb-storage/2008-November/004181.html
[2] http://marc.info/?l=linux-usb&m=121762869915609&w=2
Signed-off-by: Ben Efros <ben@pc-doctor.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the SANE SENSE flag to indicate that a device is capable of handling
more than 18-bytes of sense data. This functionality is required for
USB-ATA bridges implementing SAT. A future patch will actually enable this
function for several devices.
The logic behind this is that we can detect support for SANE_SENSE in a few ways:
1) ATA PASS THROUGH (12) or (16) execute successfully
2) SPC-3 or higher is in use
3) A previous CHECK CONDITION occurred with sense format 70-73 and had
a length greater than 18-bytes total
Signed-off-by: Ben Efros <ben@pc-doctor.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1171) removes us->sensebuf, since it isn't used anywhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1170) removes some duplicate entries in unusual_devs.h
and rearranges a few others to put the list in proper numerical order.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1166) changes usb_new_device(). Now new devices will be
announced in the log _prior_ to being registered; this way the "new
device" lines will appear before all the output from driver probing,
which seems much more logical.
Also, the patch adds a call to usb_stop_pm() to the failure pathway,
so that the parent's count of unsuspended children will remain correct
if registration fails. In order for this to work properly, the code
to increment that count has to be moved forward, before the first
point where a failure can occur.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbmon can only be built as a module if usbcore is a module too. Trivial
changes to the relevant Kconfig and Makefile (and a few trivial changes
elsewhere) allow usbmon to be built as a module even if usbcore is
builtin.
This is verified to work in all 9 permutations (3 correctly prohibited
by Kconfig, 6 build a suitable result).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
no argument named @index in pio_irq_disable, and
no argument named @req in inc_ep_stats_bytes,
remove them.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the more common platform_get_resource() together with index instead
of depending on the resource name and platform_get_resource_by_name().
Replace the resource_len() implementation with resource_size().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The legacy i2c binding model will go away soon, convert ohci-pnx4008
to use the new binding model instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a new call to be able to do a USB reset from an
atomic contect. This is quite helpful in USB callbacks to handle
errors (when the only thing that can be done is to do a device
reset).
It is done queuing a work struct that will do the actual reset. The
struct is "attached" to an interface so pending requests from an
interface are removed when said interface is unbound from the driver.
The call flow then becomes:
usb_queue_reset_device()
__usb_queue_reset_device() [workqueue]
usb_reset_device()
usb_probe_interface()
usb_cancel_queue_reset() [error path]
usb_unbind_interface()
usb_cancel_queue_reset()
usb_driver_release_interface()
usb_cancel_queue_reset()
Note usb_cancel_queue_reset() needs smarts to try not to unqueue when
it is actually being executed. This happens when we run the reset from
the workqueue: usb_reset_device() is called and on interface unbind
time, usb_cancel_queue_reset() would be called. That would deadlock on
cancel_work_sync(). To avoid that, we set (before running
usb_reset_device()) usb_intf->reset_running and clear it inmediately
after returning.
Patch is against 2.6.28-rc2 and depends on
http://marc.info/?l=linux-usb&m=122581634925308&w=2 (as submitted by
Alan Stern).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1160b) adds support routines for asynchronous autosuspend
and autoresume, with accompanying documentation updates. There
already are several potential users of this interface, and others are
likely to arise as autosuspend support becomes more widespread.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1163b) adds a "quirks=" module parameter to usb-storage.
This will allow people to make short-term changes to their
unusual_devs list without rebuilding the entire driver. Testing will
become much easier, and less-sophisticated users will be able to
access their buggy devices after a simple config-file change instead
of having to wait for a new kernel release.
The patch also adds a documentation entry for usb-storage's
"delay_use" parameter, which has been around for years but but was
never listed among the kernel parameters.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.
There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.
Quote from original descriprion:
The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will
contain one or more ports. For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller. If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed. When an ehci driver
is loaded, it explicitly takes control of the ports. If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not. If it
is high speed, the driver retains control of the port. If it is not,
the driver explicitly gives the companion controller control of the
port.
The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html
and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2
The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The QE UDC doesn't check for cpm_muram_alloc() return values, this
might cause all sorts of misbehaviour when cpm_muram_alloc() failed
to allocate the muram memory.
While at at, change few dev_dbg() calls to dev_err(), so that the
driver would not die silently.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1161) changes the interface to
usb_lock_device_for_reset(). The existing interface is apparently not
very clear, judging from the fact that several of its callers don't
use it correctly. The new interface always returns 0 for success and
it always requires the caller to unlock the device afterward.
The new routine will not return immediately if it is called while the
driver's probe method is running. Instead it will wait until the
probe is over and the device has been unlocked. This shouldn't cause
any problems; I don't know of any cases where drivers call
usb_lock_device_for_reset() during probe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems that there's rather involved way to say something
which is commonly written in a plain simple form.
Some type changes would probably be necessary to get gcc
to do bitops instead of divide but it's no worse after my
change than before I think.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this introduces a sanity check into berry_charge to give up before
damage is done if we lack juice.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just over a year ago (!) I had this brief exchange with Alan Stern:
>> It seems that the signal that can be used with USBDEVFS_DISCSIGNAL and
>> in usbdevfs_urb.signr is limited to the real-time signals SIGRTMIN to
>> SIGRTMAX. What's the rationale for this restriction? I believe that a
>> process can kill() itself with any signal number, can't it? I was
>> planning to use SIGIO for usbdevfs_urb.signr and SIGTERM (uncaught) for
>> USBDEVFS_DISCSIGNAL. I don't think I'll have a problem with using
>> SIGRTMIN+n instead, but I'm curious to know if there's some subtle
>> problem with the non-real-time signals that I should be aware of.
>
> I don't know of any reason for this restriction.
Since no-one else could think of a reason either, I offer the following
patch which allows any signal to be used with USBDEVFS_DISCSIGNAL and
usbdevfs_urb.signr.
Signed-off-by: Phil Endecott <usbpatch@chezphil.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also a trivial annotation in rh.c for:
drivers/usb/wusbcore/rh.c:366:9: warning: incorrect type in assignment (different base types)
drivers/usb/wusbcore/rh.c:366:9: expected unsigned short [unsigned] [short] [usertype] <noident>
drivers/usb/wusbcore/rh.c:366:9: got restricted __le16 [usertype] <noident>
drivers/usb/wusbcore/rh.c:367:9: warning: incorrect type in assignment (different base types)
drivers/usb/wusbcore/rh.c:367:9: expected unsigned short [unsigned] [short] [usertype] <noident>
drivers/usb/wusbcore/rh.c:367:9: got restricted __le16 [usertype] <noident>
Association types annotation fixes piles of warnings similar to:
drivers/usb/wusbcore/cbaf.c:238:30: warning: incorrect type in initializer (different base types)
drivers/usb/wusbcore/cbaf.c:238:30: expected restricted __le16 [usertype] id
drivers/usb/wusbcore/cbaf.c:238:30: got int
drivers/usb/wusbcore/cbaf.c:238:30: warning: incorrect type in initializer (different base types)
drivers/usb/wusbcore/cbaf.c:238:30: expected restricted __le16 [usertype] len
drivers/usb/wusbcore/cbaf.c:238:30: got int
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of waiting a painful 5000ms, quirk_usb_disable_ehci() now does a
1000ms loop to wait for the BIOS to acknowledge the handoff.
The five second delay is really quite irritating to have to deal with
every boot up, and I very seriously doubt any non-broken bios takes more
than a second to do the actual handoff.
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1156) straightens out some code in usbcore. The
usb_create_intf_ep_files() and usb_remove_intf_ep_files() routines
don't need to be separate inlines; they should be moved bodily into
the places where they get used.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's no need to take the address of the function params or local variables
when the direct value byteswapping routines are available.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will let us use this header in other header files.
Will be needed for the FHCI USB Host driver.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements the support for Oxford OXU210HP USB high-speed host,
no peripheral nor OTG.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: Kan Liu <kan.k.liu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For function ehci_bus_resume()
- Added flag resume_needed
No need to wait for 20ms if no port was suspended
- Change mdelay to msleep
- release and reacquire the spinlock around mdelay
Signed-off-by: vikram pandita <vikram.pandita@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the newly introduced pci_ioremap_bar() function in drivers/usb.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
temp, bytes and param->{length,sglen,vary} are unsigned so
these tests do nothing.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects the issue when one connects a Nokia 5200 cell
phone in data storage mode. If one uses an unpatched unusual_devs.h,
the following messages appear on /var/log/messages:
Dec 12 01:03:24 alberich kernel: usb 4-2: new full speed USB device
using uhci_hcd and address 3
Dec 12 01:03:25 alberich kernel: usb 4-2: configuration #1 chosen from 1 choice
Dec 12 01:03:25 alberich kernel: scsi10 : SCSI emulation for USB Mass
Storage devices
Dec 12 01:03:25 alberich kernel: usb 4-2: New USB device found,
idVendor=0421, idProduct=04bd
Dec 12 01:03:25 alberich kernel: usb 4-2: New USB device strings:
Mfr=1, Product=2, SerialNumber=3
Dec 12 01:03:25 alberich kernel: usb 4-2: Product: Nokia 5200
Dec 12 01:03:25 alberich kernel: usb 4-2: Manufacturer: Nokia
Dec 12 01:03:25 alberich kernel: usb 4-2: SerialNumber: 353930018354523
Dec 12 01:03:25 alberich kernel: usbcore: registered new interface driver ub
Dec 12 01:03:30 alberich kernel: scsi 10:0:0:0: Direct-Access
Nokia Nokia 5200 0000 PQ: 0 AN
SI: 4
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] 3985409 512-byte
hardware sectors (2041 MB)
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Write Protect is off
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Assuming drive
cache: write through
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] 3985409 512-byte
hardware sectors (2041 MB)
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Write Protect is off
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Assuming drive
cache: write through
Dec 12 01:03:30 alberich kernel: sdg: sdg1
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Attached SCSI removable disk
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: Attached scsi generic sg9 type 0
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Sense Key : No
Sense [current]
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Add. Sense: No
additional sense information
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Sense Key : No
Sense [current]
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Add. Sense: No
additional sense information
Dec 12 01:03:30 alberich kernel: sd 10:0:0:0: [sdg] Sense Key : No
Sense [current]
(...)
The MicroSD card in the phone remains inaccessible and finally the
cell phone turns itself off. The patch solves this problem and makes
the cell phone fully accessible:
[root@alberich kernel-linus-2.6.27.5-1mdv]# df -h
Sist. Arq. Tam Usad Disp Uso% Montado em
/dev/sda6 31G 5,2G 26G 17% /
/dev/sda1 92M 27M 61M 31% /boot
/dev/mapper/homevg-homelv 240G 237G 3,5G 99% /home
/dev/sda3 21G 7,9G 13G 40% /mnt/windows
/dev/sdg1 2,0G 287M 1,7G 15% /media/disk <--------
I've found necessary to use the FL_US_CAPACITY_FIX switch, as without
it the cell phone is recognized but it went berserk when performing
low-level functions on it (a fdisk -l /dev/uba for example).
lsusb -v output follows:
Bus 004 Device 004: ID 0421:04bd Nokia Mobile Phones
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0421 Nokia Mobile Phones
idProduct 0x04bd
bcdDevice 6.03
iManufacturer 1 Nokia
iProduct 2 Nokia 5200
iSerial 3 353930018354523
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0001
Self Powered
Signed-off-by: Paulo Afonso Graner Fessel <pfessel@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This device has been released in a new revision which is still buggy.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have another Argosy USB storage device, which has the same problem
with the Argosy USB storage device already fixed in 2.6.27.7. But this
device has another product ID (840:84), so this patch adds a new entry
into unusual_devs to fix the mount problem.
I enclose here two patches: one against 2.6.27.8, and another against
the latest linus-git tree.
The information about the Argosy device is like below:
#lsusb -v -d 840:84
Bus 005 Device 005: ID 0840:0084 Argosy Research, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0840 Argosy Research, Inc.
idProduct 0x0084
bcdDevice 0.01
iManufacturer 1 Generic
iProduct 2 USB 2.0 Storage Device
iSerial 3 8400000000002549
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Before the patch, dmesg returns a lot of information like below (my
dmesg is overflown):
....
[ 138.833390] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
[ 138.877631] sd 7:0:0:0: [sdb] Sense Key : No Sense [current]
[ 138.877643] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
[ 138.921906] sd 7:0:0:0: [sdb] Sense Key : No Sense [current]
[ 138.921923] sd 7:0:0:0: [sdb] Add. Sense: No additional sense information
....
After the fix, dmesg returns below information:
....
usb 5-1: new high speed USB device using ehci_hcd and address 5
usb 5-1: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 7:0:0:0: Direct-Access HTS54808 0M9AT00 MG4O PQ: 0 ANSI: 0
sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
sd 7:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 7:0:0:0: [sdb] Write Protect is off
sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00
sd 7:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 7:0:0:0: [sdb] Attached SCSI disk
sd 7:0:0:0: Attached scsi generic sg1 type 0
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Cc: Kuniyasu Suzaki <k.suzaki@aist.go.jp>
Signed-off-by: Nguyen Anh Quynh <aquynh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PM: Simplify the new suspend/hibernation framework for devices
Following the discussion at the Kernel Summit, simplify the new
device PM framework by merging 'struct pm_ops' and
'struct pm_ext_ops' and removing pointers to 'struct pm_ext_ops'
from 'struct platform_driver' and 'struct pci_driver'.
After this change, the suspend/hibernation callbacks will only
reside in 'struct device_driver' as well as at the bus type/
device class/device type level. Accordingly, PCI and platform
device drivers are now expected to put their suspend/hibernation
callbacks into the 'struct device_driver' embedded in
'struct pci_driver' or 'struct platform_driver', respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If reading the device descriptor fails during hub_port_init() fails,
then the port is disabled, disconnecting the device. The port is then
reset at the start of the next init attempt but there is no device to
reset.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Fsync currently has a fdatawrite/fdatawait pair around the method call,
and a mutex_lock/unlock of the inode mutex. All callers of fsync have
to duplicate this, but we have a few and most of them don't quite get
it right. This patch adds a new vfs_fsync that takes care of this.
It's a little more complicated as usual as ->fsync might get a NULL file
pointer and just a dentry from nfsd, but otherwise gets afile and we
want to take the mapping and file operations from it when it is there.
Notes on the fsync callers:
- ecryptfs wasn't calling filemap_fdatawrite / filemap_fdatawait on the
lower file
- coda wasn't calling filemap_fdatawrite / filemap_fdatawait on the host
file, and returning 0 when ->fsync was missing
- shm wasn't calling either filemap_fdatawrite / filemap_fdatawait nor
taking i_mutex. Now given that shared memory doesn't have disk
backing not doing anything in fsync seems fine and I left it out of
the vfs_fsync conversion for now, but in that case we might just
not pass it through to the lower file at all but just call the no-op
simple_sync_file directly.
[and now actually export vfs_fsync]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... and don't bother in callers. Don't bother with zeroing i_blocks,
while we are at it - it's already been zeroed.
i_mode is not worth the effort; it has no common default value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: (31 commits)
uwb: remove beacon cache entry after calling uwb_notify()
uwb: remove unused include/linux/uwb/debug.h
uwb: use print_hex_dump()
uwb: use dev_dbg() for debug messages
uwb: fix memory leak in uwb_rc_notif()
wusb: fix oops when terminating a non-existant reservation
uwb: fix oops when terminating an already terminated reservation
uwb: improved MAS allocator and reservation conflict handling
wusb: add debug files for ASL, PZL and DI to the whci-hcd driver
uwb: fix oops in debug PAL's reservation callback
uwb: clean up whci_wait_for() timeout error message
wusb: whci-hcd shouldn't do ASL/PZL updates while channel is inactive
uwb: remove unused beacon group join/leave events
wlp: start/stop radio on network interface up/down
uwb: add basic radio manager
uwb: add pal parameter to new reservation callback
uwb: fix races between events and neh timers
uwb: don't unbind the radio controller driver when resetting
uwb: per-radio controller event thread and beacon cache
uwb: add commands to add/remove IEs to the debug interface
...
We don't need the BKL here any more so it can go. In a couple of spots the
driver requirements are not clear so push the lock down into the driver.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The underlying problem is that the device methods don't all correctly
handle disconnected status and some keep reporting bytes pending which
causes tcdrain to stall.
When the cable is unplugged they are definitely gone, and as this is true
for all USB cables we can fix it in the core usb serial code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add device funtion for usb serial console, so we can open /dev/console
when we use a usb serial device as console.
(Typecast removed as noted by Sergei Shtylyov)
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB serial has always had races where the tty port usage count can hit zero
during a receive event. The internal locking is a mutex so we can't use
that in the IRQ handlers.
With krefs we can tackle this differently but we still need to be careful.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (105 commits)
SELinux: don't check permissions for kernel mounts
security: pass mount flags to security_sb_kern_mount()
SELinux: correctly detect proc filesystems of the form "proc/foo"
Audit: Log TIOCSTI
user namespaces: document CFS behavior
user namespaces: require cap_set{ug}id for CLONE_NEWUSER
user namespaces: let user_ns be cloned with fairsched
CRED: fix sparse warnings
User namespaces: use the current_user_ns() macro
User namespaces: set of cleanups (v2)
nfsctl: add headers for credentials
coda: fix creds reference
capabilities: define get_vfs_caps_from_disk when file caps are not enabled
CRED: Allow kernel services to override LSM settings for task actions
CRED: Add a kernel_service object class to SELinux
CRED: Differentiate objective and effective subjective credentials on a task
CRED: Documentation
CRED: Use creds in file structs
CRED: Prettify commoncap.c
CRED: Make execve() take advantage of copy-on-write credentials
...
Instead of the home-grown d_fnstart(), d_fnend() and d_printf() macros,
use dev_dbg() or remove the message entirely.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
drivers/usb/gadget/m66592-udc.c: In function 'm66592_probe':
drivers/usb/gadget/m66592-udc.c:1672: warning: label 'clean_up2' defined but not used
drivers/usb/host/r8a66597-hcd.c: In function 'r8a66597_probe':
drivers/usb/host/r8a66597-hcd.c:2401: warning: label 'clean_up2' defined but not used
Added by commit 985fc7c81c7852f2e104c71cbe913ace683c9e6a ("sh: sh_mobile
usbf clock framework support").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the usb/r8a66597 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the usbf/m66592 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements the Nokia vendor-specific communication device class
function to exchange Phonet messages over USB. This function is already
found in the "PC suite" USB profile of (non-Linux) Nokia handsets.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add id for the Hewlett-Packard LD220-HP POS pole display.
Bus 002 Device 002: ID 03f0:3524 Hewlett-Packard
Signed-off-by: Mike Provencher <mike.provencher@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver transfers firmware. It may just as well set the correct
configuration.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the "Superial" USB-Serial converter to pl2303 so that it
is detected, by the correct driver. Adds the relevant vendor:product
(5372:2303) to the device tables in pl2303.c & pl2303.h. The patch has
been tested against 2.6.24-22-generic.
Signed-off-by: Matthew D Arnold <matthew.arnold-1@uts.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a driver unbinds from an interface, usbcore always sends a
Set-Interface request to reinstall altsetting 0. Unforunately, quite
a few devices have buggy firmware that crashes when it receives this
request.
To avoid such problems, this patch (as1180) arranges to send the
Set-Interface request only when the interface is not already in
altsetting 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a bug specific to highspeed mode in the recently updated RNDIS
support: it wasn't setting up the high speed notification endpoint,
which prevented high speed RNDIS links from working.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Someone on rmweb reminded me this had been overlooked from ages ago..
Add the identifiers for the Sprog II USB. This is a DCC control interface
using the FTDI-SIO hardware: http://www.sprog-dcc.co.uk/. People have been
using it with insmod options for ages, this just puts it into the driver
data.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1179) updates the unusual_devs entry for Nokia's 5310
phone to include a more recent firmware revision.
This fixes Bugzilla #12099.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Robson Roberto Souza Peixoto <robsonpeixoto@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2.6.26(.x, cannot remember) could handle the microSD card in my Nokia
3109c attached via USB as mass storage, 2.6.27(.x, up to and included
2.6.27.8) cannot. Please find the attached patch which fixes this
regression, and a copy of /proc/bus/usb/devices with my phone plugged in
running with this patch on Frugalware.
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0421 ProdID=0063 Rev= 6.01
S: Manufacturer=Nokia
S: Product=Nokia 3109c
S: SerialNumber=359561013742570
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
From: CSÉCSY László <boobaa@frugalware.org>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbtmc driver forgot to export its device table to userspace.
Without this, it is never loaded properly when such a device is seen by
the system.
Cc: Marcel Janssen <marcel.janssen@admesy.nl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greatly enhance the MAS allocator:
- Handle row and column reservations.
- Permit all the available MAS to be allocated.
- Follows the WiMedia rules on MAS selection.
Take appropriate action when reservation conflicts are detected.
- Correctly identify which reservation wins the conflict.
- Protect alien BP reservations.
- If an owned reservation loses, resize/move it.
- Follow the backoff procedure before requesting additional MAS.
When reservations are terminated, move the remaining reservations (if
necessary) so they keep following the MAS allocation rules.
Signed-off-by: Stefano Panella <stefano.panella@csr.com>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Switch to gpio_request/free calls
Cc: linux-usb@vger.kernel.org
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Folded together as one diff from 3]
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Orion ehci driver serves the Orion, kirkwood and DD Soc families.
Since each of those integrate a different USB phy we should have the
ability to use few initialization sequences or to leave the boot loader
phy settings as is.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds an unusual_devs entry for the Nikon D2H camera.
From: Tobias Kunze Briseño <t@fictive.com>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit. Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.
This fixes Bugzilla #11583.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Tamas Kerecsen <kerecsen@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadgets disable endpoints in their disconnect callbacks, so
we must call disconnect before unbinding. This also fixes
muram memory leak, since we free muram in the qe_ep_disable().
But mainly the patch fixes following badness:
root@b1:~# insmod fsl_qe_udc.ko
fsl_qe_udc: Freescale QE/CPM USB Device Controller driver, 1.0
fsl_qe_udc e01006c0.usb: QE USB controller initialized as device
root@b1:~# insmod g_ether.ko
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC be:2d:3c:fa:be:f0
usb0: HOST MAC 62:b8:6a:df:38:66
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
fsl_qe_udc e01006c0.usb: fsl_qe_udc bind to driver g_ether
g_ether gadget: high speed config #1: CDC Ethernet (ECM)
root@b1:~# rmmod g_ether.ko
------------[ cut here ]------------
Badness at drivers/usb/gadget/composite.c:871
[...]
NIP [d10c1374] composite_unbind+0x24/0x15c [g_ether]
LR [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
Call Trace:
[cfb93e80] [cfb1f3a0] 0xcfb1f3a0 (unreliable)
[cfb93eb0] [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
[cfb93ed0] [d10c2a3c] usb_composite_unregister+0x3c/0x4c [g_ether]
[cfb93ee0] [c006bde0] sys_delete_module+0x130/0x19c
[cfb93f40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
fsl_qe_udc e01006c0.usb: unregistered gadget driver 'g_ether'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is required for all AMD SB600 revisions to avoid USB subsystem hang
symptom. The USB subsystem hang symptom is observed when the system has
multiple USB devices connected to it. In some cases a USB hub may be required
to observe this symptom.
Reported in bugzilla as #11599, the similar patch for SB700 old revision is:
commit b09bc6cbae
Reported-by: raffaele <ralfconn@tele2.it>
Tested-by: Roman Mamedov <roman@rm.pp.ru>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit f0d781d59c.
It was the wrong thing to do, and does not really do what it said
it did.
Cc: Yi Yang <yi.y.yang@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add asl, pzl and di debugfs files to uwb/uwbN/wusbhc for WHCI host
controller. These dump the current ASL, PZL and DI buffer.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
ASL/PZL updates while the WUSB channel is inactive (i.e., the PZL and
ASL are stopped) may not complete. This causes hangs when removing the
whci-hcd module if a device is still connected (removing the device
does an endpoint_disable which results in an ASL update to remove the
qset).
If the WUSB channel is inactive the update can simply be skipped as the
WHC doesn't care about the state of the ASL/PZL.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
the use of is_blah() suggests a 1 or 0 return. This assumption is made in
pxa25x_udc code such as:
dev->vbus = is_vbus_present();
where dev->vbus is a bitfield. This fix allows pxa25x_udc_probe to correctly
detect vbus. Other changes were to make its use consistent in the rest of
the code.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ethernet devices are converted, the function pointer setup
by eth_setup() need to be done during intialization.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch which adds IDs for AKTAKOM USB->RS232 cable
(http://www.aktakom.ru/product/kio/ace-1001.htm) is attached.
From: M Kondrin <mkondrin@hppi.troitsk.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a bug in the usbmon binary reader: When using read() to fetch
the packets and a packet's data is partially read, the next read call
will once again return up to len_cap bytes of data. The b_read counter
is not regarded when determining the remaining chunk size.
So, when dumping USB data with "cat /dev/usbmon0 > usbmon.trace" while
reading from a USB storage device and analyzing the dump file
afterwards it will get out of sync after a couple of packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that atomic_inc_return() returns the *new* value
not the original one, so the logic in rndis_response_available()
kept the first RNDIS response notification from getting out.
This prevented interoperation with MS-Windows (but not Linux).
Fix this to make RNDIS behave again.
Signed-off-by: Richard Röjfors <richard.rojfors@endian.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Somewhere in the conversion of the RNDIS gadget code to the new
framework, the descriptor of its data interface seems to have
been copied from the CDC Ethernet driver. Unfortunately that
means it got a nonzero altsetting ... which is incorrect. Issue
uncovered by Richard Röjfors <richard.rojfors@endian.se>.
This patch fixes that problem, and resolves at least some cases
of Windows XP bluescreening itself.
Tested-by: Richard Röjfors <richard.rojfors@endian.se>.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1168) updates the unusual_devs entry for the Nokia 5300.
According to Jorge Lucangeli Obes <t4m5yn@gmail.com>, some existing
models have a revision number lower than the lower limit of the
current entry.
The patch also moves the entry for the Nokia 5310 to its correct place
in the file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1169) modifies the unusual_devs entry for the Nokia
6300. According to Maciej Gierok <mgierok@gmail.com> and David
McBride <dwm@doc.ic.ac.uk>, the revision limits need to be wider.
This fixes Bugzilla #11768.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This bug was introduced recently. Fix it before bigger
problems appear.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is required for AMD SB700 south bridge revision A12 and A13 to avoid
USB subsystem hang symptom. The USB subsystem hang symptom is observed when the
system has multiple USB devices connected to it. In some cases a USB hub may be
required to observe this symptom.
This patch works around the problem by correcting the internal register setting
that will help by changing the behavior of the internal logic to avoid the
USB subsystem hang issue. The change in the behavior of the logic does not
impact the normal operation of the USB subsystem.
Reported-by: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Tested-by: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The UWB radio manager coordinates the use of the radio between the
PALs that may be using it. PALs request use of the radio with
uwb_radio_start() and the radio manager will start beaconing if its
not already doing so. When the last PAL has called uwb_radio_stop()
beaconing will be stopped.
In the future, the radio manager will have a more sophisticated channel
selection algorithm, probably following the Channel Selection Policy
from the WiMedia Alliance when it is finalized. For now, channel 9
(BG1, TFC1) is selected.
The user may override the channel selected by the radio manager and may
force the radio to stop beaconing.
The WUSB Host Controller PAL makes use of this and there are two new
debug PAL commands that can be used for testing.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Conflicts:
security/keys/internal.h
security/keys/process_keys.c
security/keys/request_key.c
Fixed conflicts above by using the non 'tsk' versions.
Signed-off-by: James Morris <jmorris@namei.org>
Wrap current->cred and a few other accessors to hide their actual
implementation.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
This fixes a deadlock appearing with some USB peripheral drivers
when running CDC ACM gadget code.
The newish (2.6.27) CDC ACM event notification mechanism sends
messages (IN to the host) which are short enough to fit in most
FIFOs. That means that with some peripheral controller drivers
(evidently not the ones used to verify the notification code!!)
the completion callback can be issued before queue() returns.
The deadlock would come because the completion callback and the
event-issuing code shared a spinlock. Fix is trivial: drop
that lock while queueing the message.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1164) fixes a bug in the EHCI scheduler. The interval
value it uses is already in linear format, not logarithmically coded.
The existing code can sometimes crash the system by trying to divide
by zero.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1165) makes a few small changes in the logic used by
ehci-hcd when it encounters a controller error:
Instead of printing out the masked status, it prints the
original status as read directly from the hardware.
It doesn't check for the STS_HALT status bit before taking
action. The mere fact that the STS_FATAL bit is set means
that something bad has happened and the controller needs to
be reset. With the old code this test could never succeed
because the STS_HALT bit was masked out from the status.
I anticipate that this will prevent the occasional "irq X: nobody cared"
problem people encounter when their EHCI controllers die.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I used SuperH on-chip USB, there was the problem that accessed
r8a66597_root_hub which was not allocated.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Additional sectors were reported by the Nokia 7610 Supernova phone in
usb storage mode. The following patch rectifies the aforementioned
problem.
Signed-off-by: Ricky Wong Yung Fei <evilbladewarrior@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roland Reported the following:
| kmem_cache_create: duplicate cache isp1760_qtd
| Pid: 461, comm: modprobe Tainted: G W 2.6.28-rc2-git3-default #4
| Call Trace:
| [<c017540e>] kmem_cache_create+0xc9/0x3a3
| [<c0159a8d>] free_pages_bulk+0x16c/0x1c9
| [<f165c05f>] isp1760_init+0x0/0xb [isp1760]
| [<f165c018>] init_kmem_once+0x18/0x5f [isp1760]
| [<f165c064>] isp1760_init+0x5/0xb [isp1760]
| [<c010113d>] _stext+0x4d/0x148
| [<c0142936>] load_module+0x12cd/0x142e
| [<c01743c4>] kmem_cache_destroy+0x0/0xd7
| [<c0142b1e>] sys_init_module+0x87/0x176
| [<c01039eb>] sysenter_do_call+0x12/0x2f
The reason, is that ret is initialized with ENODEV instead of 0 _or_
the kmem cache is not freed in error case with no bus binding.
The difference between OF+PCI and OF only is
| 15148 804 32 15984 3e70 isp1760-of-pci.o
| 13748 676 8 14432 3860 isp1760-of.o
about 1.5 KiB.
Until there is a checkbox where the user *must* select atleast one item,
and may select multiple entries I don't make it selectable anymore.
Having a driver which can't be used under any circumstances is broken
anyway and I've seen distros shipping it that way.
Reported-by: Roland Kletzing <devzero@web.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>a
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enfora GSM2228 based on Cygnal Integrated Products chip uses the same
cp2101 driver.
Signed-off-by: Damir N Abdullin <damir@mimas.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 65934a9 ("Make USB storage depend on SCSI rather than selecting
it [try #6]") the comment at the top of drivers/usb/storage/Kconfig is
incorrect. Adjust it to the current situation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ehci_shutdown() or ohci_shutdown() calls to the USB
PS3 bus glue. ehci_shutdown() and ohci_shutdown() do some
controller specific cleanups not done by usb_remove_hcd().
Fixes errors on shutdown or reboot similar to these:
ps3-ehci-driver sb_07: HC died; cleaning up
irq 51: nobody cared (try booting with the "irqpoll" option)
Related bugzilla reports:
http://bugzilla.kernel.org/show_bug.cgi?id=11819http://bugzilla.terrasoftsolutions.com/show_bug.cgi?id=317
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb_free_urb comment says that the transfer buffer will not be
freed, but this is not the case when URB_FREE_BUFFER is set.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds YISO u893 usb modem vendor and product ID to option.c.
I had a better experience using this modification and the same system.
Signed-off-by: Leslie Harlley Watter <leslie@watter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes co-working issue of usb serial device with usb/net devices while
oter endpoints are free and can be used.This patch implements the policy
that if endpoint resources are available then different BULK request goes
to different endpoint otherwise they are multiplexed to one reserved
endpoint as currently done.
Switch statement case is reordered in musb_giveback() to take care of
bulk request both in multiplex scenario and otherwise.
NAK limit scheme has to be added for multiplexed BULK request scenario
to avoid endpoint starvation due to usb/net devices.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to avoid namespace conflicts, add a prefix
to our kernel-wise symbol.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes blurred capture images in dma mode. Isochronous error field in
urb and source data buffer pointer were not updated properly in dma
mode.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1155) fixes a bug in usbcore. When interfaces are
deleted, either because the device was disconnected or because of a
configuration change, the extra attribute files and child endpoint
devices may get left behind. This is because the core removes them
before calling device_del(). But during device_del(), after the
driver is unbound the core will reinstall altsetting 0 and recreate
those extra attributes and children.
The patch prevents this by adding a flag to record when the interface
is in the midst of being unregistered. When the flag is set, the
attribute files and child devices will not be created.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [2.6.27, 2.6.26, 2.6.25]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/usb/host/hwa-hc.c
drivers/usb/host/whci/hcd.c
drivers/usb/host/whci/int.c
drivers/usb/host/whci/wusb.c
drivers/usb/wusbcore/cbaf.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
When we close we must clear the extra reference we got when we read
port->tty. Setting the port tty NULL will clear the kref held by the driver
but not the one we obtained ourselves while doing the lookup.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Helge Hafting <helge.hafting@aitel.hist.no>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the udc headers to the proper home in
arch/arm/plat-s3c24xx/include/plat ready to clean out
the old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch (as1153) fixes a potential problem in hub initialization.
Starting in 2.6.28, initialization was split into several tasks to
help speed up booting. This opens the possibility that the hub may be
autosuspended before all the initialization tasks can complete.
Normally that wouldn't matter, but with incomplete initialization
there is a risk that the hub would never autoresume -- especially if
devices were plugged into the hub beforehand. The solution is a
simple one-line change to suppress autosuspend until the
initialization is finished.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The camera reports an incorrect size and fails to handle PREVENT-ALLOW
MEDIUM REMOVAL commands. The patch marks the camera as an unusual dev
and adds the flags to enable the workarounds for both shortcomings.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Silences compiler warning about comparison with 0x80, and type now matches the
corresponding _bulk_out function.
drivers/usb/class/usbtmc.c: In function ‘usbtmc_ioctl_abort_bulk_in’:
drivers/usb/class/usbtmc.c:163: warning: comparison is always false due to limited range of data type
Signed-off-by: Chris Malley <mail@chrismalley.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1151) protects usbcore against drivers that try to
unlink an URB after the URB's device or bus have been removed. The
core does not currently check for this, and certain drivers can cause
a crash if they are running while an HCD is unloaded.
Certainly it would be best to fix the guilty drivers. But a little
defensive programming doesn't hurt, especially since it appears that
quite a few drivers need to be fixed.
The patch prevents the problem by grabbing a reference to the device
while an unlink is in progress and using a new spinlock to synchronize
unlinks with device removal. (There's no need to acquire a reference
to the bus as well, since the device structure itself keeps a
reference to the bus.) In addition, the kerneldoc is updated to
indicate that URBs should not be unlinked after the disconnect method
returns.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using a Reset Device IE to reset a WUSB device is too heavyweight as it
causes the devcie to disconnect (which the USB stack does not expect and
cannot handle). Instead, do a SetAddress(0); SetAddress(AuthAddr) for
authenticated devices.
Unauthenticated devices will not be reset and the stack will have to rely
on the device timing out after TrustTimeout and disconnecting.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
When stopping the WUSB channel the host should send Channel Stop IEs giving
the WUSB Channel Time of the last MMC. Both WHCI and HWA hosts provide a
channel stop command for this.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Verifing the key generation algorithms could take too long on a freshly
booted system (due to lack of entropy) so disable the test unless a module
parameter (debug_crypto_verify) is specified.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Reference counting the struct uwb_rsv's is safer and easier to get right than
the transferring ownership of the structures from the PAL to reservation
manager.
This fixes an oops in the debug PAL after a reservation timed out.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: don't rebind drivers after failed resume or reset
USB: fix memory leak in cdc-acm
USB: Unusual dev for Mio moov 330 gps
USB: cdc-wdm: make module autoload work
USB: Fix unneeded endpoint check in pxa27x_udc
usb/gadget: fix kernel-doc warning
USB: Speedtouch: add pre_reset and post_reset routines
USB: usbtest.c: length, sglen and vary are unsigned, so cannot be negative
USB: support Huawei data card product IDs
USB: add ZTE MF626 USB GSM modem entry
USB: storage: Avoid I/O errors when issuing SCSI ioctls to JMicron USB/ATA bridge
USB: Fix debugfs_create_file's error checking method for usb/gadget/s3c2410_udc
USB: ohci: add support for tmio-ohci cell
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: (47 commits)
uwb: wrong sizeof argument in mac address compare
uwb: don't use printk_ratelimit() so often
uwb: use kcalloc where appropriate
uwb: use time_after() when purging stale beacons
uwb: add credits for the original developers of the UWB/WUSB/WLP subsystems
uwb: add entries in the MAINTAINERS file
uwb: depend on EXPERIMENTAL
wusb: wusb-cbaf (CBA driver) sysfs ABI simplification
uwb: document UWB and WUSB sysfs files
uwb: add symlinks in sysfs between radio controllers and PALs
uwb: dont tranmit identification IEs
uwb: i1480/GUWA100U: fix firmware download issues
uwb: i1480: remove MAC/PHY information checking function
uwb: add Intel i1480 HWA to the UWB RC quirk table
uwb: disable command/event filtering for D-Link DUB-1210
uwb: initialize the debug sub-system
uwb: Fix handling IEs with empty IE data in uwb_est_get_size()
wusb: fix bmRequestType for Abort RPipe request
wusb: fix error path for wusb_set_dev_addr()
wusb: add HWA host controller driver
...
This patch (as1152) may help prevent some problems associated with the
new policy of unbinding drivers that don't support suspend/resume or
pre_reset/post_reset. If for any reason the resume or reset fails, and
the device is logically disconnected, there's no point in trying to
rebind the driver. So the patch checks for success before carrying
out the unbind/rebind.
There was a report from one user that this fixed a problem he was
experiencing, but the details never became fully clear. In any case,
adding these tests can't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a memory leak on disconnect in cdc-acm
Thanks to 施金前 for finding it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is an entry for the unusual_devs.h file to handle a Mio Moov 330 GPS that
stops responding when it is requested to transfer more than 64KB. The patch is
taken against kernel-2.6.27-git3.
Signed-off-by: Frédéric Marchal <frederic.marchal@wowcompany.co
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this fixes an omission that led to no alias being computed for the
cdc-wdm module.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The request allocation code doesn't need to check if the
endpoint is not NULL, as the only caller in
include/linux/usb/gadget.h, usb_ep_alloc_request() needs the
endpoint pointer to have a correct value to trigger the
allocation code.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix kernel-doc warning, wrong parameter name listed:
Warning(lin2627-g3-kdocfixes//drivers/usb/gadget/config.c:183): No description found for parameter 'match'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1150) fixes a problem in the speedtch driver. When it
resets the modem during probe it will be unbound from the other
interfaces it has claimed, because it doesn't define a pre_reset and a
post_reset method.
The patch defines "do-nothing" methods. This fixes Bugzilla #11767.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In this patch, we want to do one thing: add more Huawei product IDs into the
USB driver. Then it can support more Huawei data card devices. So to declare
the unusual device for new Huawei data card devices in unusual_devs.h and to
declare more new product IDs in option.c.
To modify the data value and length in the function of
usb_stor_huawei_e220_init in initializers.c That's because based on the USB
standard, while sending SET_FETURE_D to the device, it requires the
corresponding data to be zero, and its sending length also must be zero. In
our old solution, it can be compatible with our WCDMA data card devices, but
can not support our CDMA data card devices. But in this new solution, it can
be compatible with all of our data card devices.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's the patch that implements the fix you suggested to avoid the
I/O errors that I was running into with my new USB enclosure with a
JMicron USB/ATA bridge, while issuing scsi-io USN or other such
queries used by Fedora's mkinitrd.
http://bugzilla.kernel.org/show_bug.cgi?id=9638#c85
/proc/bus/usb/devices:
T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=152d ProdID=2329 Rev= 1.00
S: Manufacturer=JMicron
S: Product=USB to ATA/ATAPI Bridge
S: SerialNumber=DE5088854FFF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
(patch applied and retested on a modified 2.6.27.2-libre.24.rc1.fc10)
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
debugfs_create_file() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Toshiba Mobile I/O chips have OHCI controller built in.
E.g. the tc6393xb chip found in several Toshiba e-Series PDAs
and in Sharp Zaurus SL-6000 PDA. This adds platform glue
to support OHCI function of the chip.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This gets rid of an annoying warning in ehci-hcd.c when DEBUG isn't
enabled:
warning: label 'err_debug' defined but not used
by moving it inside the already-existing #ifdef DEBUG, so that it
matches the goto. And now my regular build is warning-free again.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove err() and
use the system-wide standard of dev_err() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible. In the
few places that will not work out, use a basic printk().
Clean up the remaining usages of this in the drivers/usb/ directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code didn't respond correctly to get status request on
device and endpoint. Although normal operations can work without the
fix. It is not compliant with USB spec chapter9 and fails USBCV ch9
tests. The patch fix this and a few style/typo problems.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some circumstances when fsl_udc_probe fails udc_controller is freed but
the pointer remains non-NULL. fsl_udc_remove will then try and teardown
the partly initialized and freed controller structure resulting in an oops.
This patch ensures udc_controller is either NULL or fully initialized after
fsl_udc_probe.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a wmb to fsl_queue_td before priming the endpoint. This ensures that the
modifications to the QH are seen by the hardware.
Added comment as suggested by Felipe Balbi.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fsl_queue_td always returns 0. Make it void and remove checks for non-zero
return in callers.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Uninline udc_reset_ep_queue and remove it's unused return value.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rename the arguments of the fsl_writel macro to match their use.
Remove a couple of unnecessary prototypes.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move spinlock initialization earlier so we can turn shared irq handler
debugging on safely.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Missing spaces were causing the /proc debugging output to be rather
unreadable.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Anton Vorontsov