When TX aggregation becomes operational, we do a number of steps:
1) print a debug message
2) wake the virtual queue
3) notify the driver
Unfortunately, 1) and 3) are only done if the driver is first to
reply to the aggregation request, it is, however, possible that the
remote station replies before the driver! Thus, unify the code for
this and call the new function ieee80211_agg_tx_operational in both
places where TX aggregation can become operational.
Additionally, rename the driver notification from
IEEE80211_AMPDU_TX_RESUME to IEEE80211_AMPDU_TX_OPERATIONAL.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
change the display of current driver status bit to user readable format
for better and easier debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We shouldn't return NETDEV_TX_BUSY from the TX callback, especially
after we've mucked with the sk_buffs. Drop the packets and return
NETDEV_TX_OK.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch restores all-in-one module build procedure for ar9170.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were claiming DMA buffers on the RX tasklet but never
upon a simple module removal.
Cc: stable@kernel.org
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k sets up a mapping table from the hardware rate index to
the rate index used by mac80211; however, we have seen some
received frames with incorrect rate indexes. Such frames
normally get dropped with a warning in __ieee80211_rx(),
but it doesn't include enough information to track down the
error.
This patch adds a warning to hw_to_driver_rix for any lookups
that result in a rate index of -1, then returns a valid rate so
the frame can be processed.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the return type of b43_plcp_get_bitrate_idx_ofdm. If
the plcp contains an error, the function return value is 255 instead
of -1, and the packet was not dropped. This causes a warning in
__ieee80211_rx function because rate idx is out of range.
Cc: stable@kernel.org
Signed-off-by: Lorenzo Nava <navalorenx@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates p54's Kconfig entry and removes the out-dated device list.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the tx_status report code by using four tx_queues per
station instead of only one. (the skb lookup should be in O(1) now :-p ).
Also, it fixes a really obvious copy&paste bug in the janitor work code and
adds back a few spilled bits to the hardware definition header about QoS.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add vendor ID for Quanta Microsystems and update the led table with the reported device.
Reported-by: Scott Barnes <nekoreeve@gmail.com>
Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch update all necessary Makefile and Kconfig files.
Now you can then enable ar9170 in the kernel configuration under:
Device Drivers --->
[*] Network device support --->
Wireless LAN --->
[*] Wireless LAN (IEEE 802.11)
<M> Atheros AR9170 support
<M> Atheros AR9170 USB support
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
USB frontend driver code for Atheros' AR9170 modules.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains almost all mac80211 interaction code of AR9170.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hardware / firmware interface definitions for Atheros' AR9170 based devices.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this the regulatory domain isn't seen and we end up
intersecting for each request (each radio).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables mesh point operation for ath9k. Tested with b43,
ath9k, rt2500usb, and ath5k as peers.
Signed-off-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a compile problem when the MAC80211_LEDS
triggers are enabled but not LED class itself.
(which is sort of pointless, but anyway...)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates count of every hw tried rate with
appropriate tries before reporting tx status of a frame.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This masks the PHY TX error interrupt, if debugging is disabled.
Currently we have a bug somewhere which triggers this interrupt once
in a while. (Depends on the network noise/quality). While this is nonfatal,
it scares the hell out of users and we frequently receive bugreports
that incorrectly identify this error message as the reason.
There's another problem with this. The PHY TX error interrupt is protected
with a watchdog that will restart the device if it keeps triggering very often.
This is used to fix interrupt storms from completely broken devices.
However, this watchdog might trigger in completely normal operation.
If the TX capacity of the card is saturated, the likeliness of the watchdog
triggering increases, as more TX errors occur. The current threshold
for the watchdog is 1000 errors in 15 seconds.
This patch adds a workaround for the issue by just enabling the interrupt
if debugging is disabled (by Kconfig or by modparam).
This has the downside that real fatal PHY TX errors are not caught anymore.
But this is nonfatal due to the following reasons:
* If the card is not able to transmit anymore, MLME will notice anyway.
* I did _never_ see a real fatal PHY TX error in a mainline b43 driver.
* It does _not_ result in interrupt storms or something like that.
It will simply result in a stalled card. It can be debugged by enabling
the debugging module parameter.
Signed-off-by: Michael Buesch <mb@bu3sch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will miss rate control update if first A-MPDU of an
aggregation is not Block Acked as we always tell if the
rate control needs to updated through update_rc of first
A-MPDU. This patch does rate control update for the first
A-MPDU which notifies it's tx status (which is not
necessarily the first A-MPDU of an aggregation) to mac80211.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A *leftover* stations is replaced with stations_39.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix related to bug 1921 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1921
when detect error during stopping tx aggregation queue, report the error to
help identify the problem.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Control the rate decrease. Do not decrease the rate fast.
Use success_ratio for rate scaling :)
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_cmd_queue_free needs to be used to free up the cmd_queue,
as TFD slots for cmd_queue and tx_queue are different.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Total number of queues is 8 but only 7 of them are TX queues.
4 AC(Data) queue ,1 CMD and 2 HCCA. The HCCA queues are not used.
max_txq_num is set to maximum usable TX queues.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set IEEE80211_HW_SPECTRUM_MGMT bit in hw->flags, this tell mac80211
we support spectrum mgmt.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If user set new power level, accept the new power level and only
send command to host if the interface is up and radio on.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
allow user to set power level at all times
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receive IEEE80211_AMPDU_RX_STOP or IEEE80211_AMPDU_TX_STOP request
in iwl_mac_ampdu_action() from mac80211; check STATUS_EXIT_PENDING bit,
if NIC is on the way out, then return 0 back to mac80211, this can
prevent mac80211 report HW error incorrectly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In function iwl3945_mac_config use changed flag to call only
the affected functions.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In function iwl_mac_config use changed flag to call only
the affected functions. This patch also allow user to cache
channel, txpower and power value when the interface is not
ready and apply the changes once the interface ready.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add tx power calibration support
* Add a few tx power limits
* Hardcode default power to 12.5dB
* Disable TPC for now
v2: Address Jiri's comments
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the PCI retry timeout code, for all the same reasons that
Luis Rodriguez removed it for ath9k.
Changes-licensed-under: 3-Clause-BSD
Cc: Luis Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB interrupt fires whenever counters overflow; however without
support for automatic noise immunity, we can sometimes get an interrupt
storm. The get_stats() callback reads the counters anyway so we can
disable the interrupt for now until ANI is implemented. This fixes
the issue reported in http://bugzilla.kernel.org/show_bug.cgi?id=12647.
Changes-licensed-under: 3-Clause-BSD
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Convert chip specific calibration data to a generic format common
for all chips
Note: We scale up power to be in 0.25dB units for all chips for
compatibility with RF5112
v2: Address Bob's and Jiri's comments
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix a typo in initvals.c so that we use the RF2425 array for RF2425 and not RF2413
Note: This also fixes incorect pd gain overlap since RF2425 has different pd gain overlap from RF2413
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radiotap was updated to include a "bad PLCP" flag and standardise
the "bad FCS" flag in the "flags" rather than "RX flags" field,
this patch updates Linux to that standard.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP mode currently sets up the dual stream capability
for all stations. This patch fixes it by checking if the
associated station supports dual stream MCS rates (8-15).
We would disregard any MCS rates above 15, since Atheros
HW supports only 0..15 rates currently, and can't receive
at rates > 15 anyway.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fills the ack_signal field in TX status with an appropriate
value from the TX descriptor.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be checking with the 4K header and not the non-4K
header size.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always return true, checking for 'false' return value
is bogus anyway, so fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This improves readability. Handle both 4K/non-4K EEPROM
in this patch.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print the EEPROM version/revision on init.
Choose appropriate debug masks on error conditions,
and remove useless print messages.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the PCI retry timeout code as that was just taken from ipw2100
due to historical reasons but in reality its a no-op, additionally its
simply incorrect as each PCI devices has its own custom PCI configuration
space on PCI config space >= 0x40. Not to mention we were trying to write
0 to a place that already has 0 on it.
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Ben Cahill <ben.m.cahill@intel.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Tested-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the TSF offset calculation for staggered Beacon frames
and sets ATH_BCBUF back to the earlier value 4 to enable multi-BSS
configurations of up to four BSSes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there are no free snums, UCC ethernet should gracefully fail, but
currently it oopses this way:
# ifconfig eth0 up
fill_init_enet_entries: Can not get SNUM.
ucc_geth_startup: Can not fill p_init_enet_param_shadow.
eth0: Cannot configure net device, aborting.
Unable to handle kernel paging request for data at address 0x00000190
Faulting instruction address: 0xc0294c88
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c0294c88] mutex_lock+0x0/0x1c
LR [c01b6be8] phy_stop+0x20/0x70
Call Trace:
[efb25da0] [efb2eb60] 0xefb2eb60 (unreliable)
[efb25db0] [c01b2058] ucc_geth_stop+0x2c/0x8c
[efb25dd0] [c01b4194] ucc_geth_open+0x48/0x27c
[efb25df0] [c020eec0] dev_open+0xc0/0x118
[...]
This is because the ucc_geth_stop() routine assumes that ugeth->phydev
is always initialized by the ucc_geth_open(), while it is not in case
of errors.
If we add a check to the ucc_geth_stop(), then another oops pops up:
Unable to handle kernel paging request for data at address 0x00000004
Faulting instruction address: 0xc01b46a4
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01b46a4] adjust_link+0x20/0x1b4
LR [c01b770c] phy_state_machine+0xdc/0x44c
Call Trace:
[ef83bf10] [c021b388] linkwatch_schedule_work+0x74/0xf8 (unreliable)
[ef83bf40] [c01b770c] phy_state_machine+0xdc/0x44c
[ef83bf60] [c004c13c] run_workqueue+0xb8/0x148
[ef83bf90] [c004c870] worker_thread+0x70/0xd0
[ef83bfd0] [c00505fc] kthread+0x48/0x84
[ef83bff0] [c000f464] kernel_thread+0x4c/0x68
[...]
That one happens because ucc_geth_stop() does not call phy_disconnect()
and so phylib state machine is running without any idea that a MAC has
just died.
Also, when device tree specifies fixed-link, and CONFIG_FIXED_PHY
is disabled, we'll get this oops:
0:01 not found
eth2: Could not attach to PHY
eth2: Cannot initialize PHY, aborting.
Unable to handle kernel paging request for data at address 0x00000190
Faulting instruction address: 0xc02967d0
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c02967d0] mutex_lock+0x0/0x1c
LR [c01b6bcc] phy_stop+0x20/0x70
Call Trace:
[ef82be50] [efb6bb60] 0xefb6bb60 (unreliable)
[ef82be60] [c01b2058] ucc_geth_stop+0x2c/0x8c
[ef82be80] [c01b4194] ucc_geth_open+0x48/0x27c
[ef82bea0] [c0210a04] dev_open+0xc0/0x118
[ef82bec0] [c020f85c] dev_change_flags+0x84/0x1ac
[ef82bee0] [c037b768] ic_open_devs+0x168/0x2bc
[ef82bf20] [c037ca98] ip_auto_config+0x90/0x28c
[ef82bf60] [c0001b9c] do_one_initcall+0x34/0x1a0
[ef82bfd0] [c035e240] do_initcalls+0x38/0x58
[ef82bfe0] [c035e2c4] kernel_init+0x30/0x90
[ef82bff0] [c000f464] kernel_thread+0x4c/0x68
[...]
And again, ucc_geth_stop() assumes that ugeth->phydev is there, while
it isn't.
This patch fixes all three oopses simply by rearranging some code:
- In ucc_geth_open(): move init_phy() call to the beginning, so
that we only call ucc_geth_stop() with a PHY attached;
- Move phy_disconnect() call from ucc_geth_close() to
ucc_geth_stop(), so that we'll always disconnect the PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA mapping can be expensive in the presence of iommus.
Reduce the Rx iommu activity by mapping an entire page, and provide the H/W
the mapped address + offset of the current page chunk.
Reserve bits at the end of the page to track mapping references, so the page
can be unmapped.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size_t to declare mmio start and len variables.
Print PEX error register after EEH resumed.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable timestamps, update delayed ack threshold for iSCSI/iWARP traffic
Remove the len flag in Tx requests. It might corrupt offload trace packets.
Update SGE context setup to avoid potential H/W misprogrammation.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start queue set reclaim timers after the queue sets have been
allocated successfully.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded memset (alloc_etherdev does it already).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_device_ops conversion left the wrong poll_controller hook.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert madge and proteon drivers which are really just subclasses
of tms380.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of drivers have leftovers from netdev ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN911x datasheet specifies a minimum delay of 45ns between a write
of E2P_DATA and any read. This patch adds a single dummy read of
BYTE_TEST to enforce this timing constraint.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that was added to increase headroom was wrong.
It doesn't handle the case where gfar_add_fcb() changes the skb.
Better to do check at start of transmit (outside of lock), where
error handling is better anyway.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The benet driver is doing a 64 bit divide, which is not supported in
Linux kernel on 32 bit architectures. The correct way to do this is to
use do_div(). Compile tested on i386 only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a platform device driver that supports the OpenCores 10/100
Mbps Ethernet MAC.
The driver expects three resources: one IORESOURCE_MEM resource defines the
memory region for the core's memory-mapped registers while a second
IORESOURCE_MEM resource defines the network packet buffer space. The third
resource, of type IORESOURCE_IRQ, associates an interrupt with the driver.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
RDMA/cxgb3: Enforce required firmware
IB/mlx4: Unregister IB device prior to CLOSE PORT command
mlx4_core: Add link type autosensing
mlx4_core: Don't perform SET_PORT command for Ethernet ports
RDMA/nes: Handle MPA Reject message properly
RDMA/nes: Improve use of PBLs
RDMA/nes: Remove LLTX
RDMA/nes: Inform hardware that asynchronous event has been handled
RDMA/nes: Fix tmp_addr compilation warning
RDMA/nes: Report correct vendor_id and vendor_part_id
RDMA/nes: Update copyright to new legal entity and year
RDMA/nes: Account for freed PBL after HW operation
IB: Remove useless ibdev_is_alive() tests from sysfs code
IB/sa_query: Fix AH leak due to update_sm_ah() race
IB/mad: Fix ib_post_send_mad() returning 0 with no generate send comp
IB/mad: initialize mad_agent_priv before putting on lists
IB/mad: Fix null pointer dereference in local_completions()
IB/mad: Fix RMPP header RRespTime manipulation
IB/iser: Remove hard setting of path MTU
mlx4_core: Add device IDs for MT25458 10GigE devices
...
When changing DCB parameters, ixgbe needs to have the MAC reset. The way
the flow control code is setup today, PFC will be disabled on a reset.
This patch adds a new flow control type for PFC, and then has the netlink
layer take care of toggling which type of flow control to enable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Alan Cox, it is possible for e1000e to exit its interrupt
handler or NAPI with interrupts enabled even when the driver is unloading or
being configured administratively down.
fix related to fix for: http://bugzilla.kernel.org/show_bug.cgi?id=12876
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e (and e1000, igb, ixgbe, ixgb) all do a series of operations each
time a multicast address is added. The flow goes something like
1) stack adds one multicast address
2) stack passes whole current list of unicast and multicast addresses to
driver
3) driver clears entire list in hardware
4) driver programs each multicast address using iomem in a loop
This was causing multicast packets to be lost during the reprogramming
process.
reference with test program:
http://kerneltrap.org/mailarchive/linux-netdev/2009/3/14/5160514/thread
Thanks to Dave Boutcher for his report and test program.
This driver fix prepares an array all at once in memory and programs it in
one shot to the hardware, not requiring an "erase" cycle. It would still
be possible for packets to be dropped while the receiver is off during
reprogramming.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Dave Boutcher <daveboutcher@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the e1000e tx cleanup routine to more closely match
what already exists in igb and e1000.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this is in regards to
http://bugzilla.kernel.org/show_bug.cgi?id=12876
where it appears that e1000 can leave its interrupt enabled after
exiting the driver. Fix the bug by making the interrupt enable
paths more aware of the driver exiting.
Thanks to Alan Cox for the poke and initial investigation.
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx cleanup routine was stopping after 64 packets and this was causing
issues resulting in the ring not being completely cleaned.
This change updates the driver to clean the entire ring and if it doesn't
it then will retry on the next pass.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the dma mapping to better support
skb_dma_map/skb_dma_unmap and addresses and redefines the tx hang logic to
be based off of time stamp instead of if the dma field is populated
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've hit an issue on my system when I've been using RealTek RTL8139D cards in
bonding interface in mode balancing-alb. When I enslave a card, the current
active slave (bond->curr_active_slave) is not set and the link is therefore
not functional.
----
# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
Bonding Mode: adaptive load balancing
Primary Slave: None
Currently Active Slave: None
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:1f:1f:01:2f:22
----
The thing that gets it right is when I unplug the cable and then I put it back
into the NIC. Then the current active slave is set to eth1 and link is working
just fine. Here is dmesg log with bonding DEBUG messages turned on:
----
ADDRCONF(NETDEV_UP): bond0: link is not ready
event_dev: bond0, event: 1
IFF_MASTER
event_dev: bond0, event: 8
IFF_MASTER
bond_ioctl: master=bond0, cmd=35216
slave_dev=cac5d800:
slave_dev->name=eth1:
eth1: ! NETIF_F_VLAN_CHALLENGED
event_dev: eth1, event: 8
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 1
event_dev: eth1, event: 8
IFF_SLAVE
Initial state of slave_dev is BOND_LINK_UP
bonding: bond0: enslaving eth1 as an active interface with an up link.
ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
event_dev: bond0, event: 4
IFF_MASTER
bond0: no IPv6 routers present
<<<<cable unplug>>>>
eth1: link down
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely down for interface eth1, disabling it
event_dev: bond0, event: 4
IFF_MASTER
<<<<cable plug>>>>
eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
event_dev: eth1, event: 4
IFF_SLAVE
bonding: bond0: link status definitely up for interface eth1.
bonding: bond0: making interface eth1 the new active one.
event_dev: eth1, event: 8
IFF_SLAVE
event_dev: eth1, event: 8
IFF_SLAVE
bonding: bond0: first active interface up!
event_dev: bond0, event: 4
IFF_MASTER
----
The current active slave is set by calling bond_select_active_slave() function
from bond_miimon_commit() function when the slave (eth1) link goes to state up.
I also tested this on other machine with Broadcom NetXtreme II BCM5708
1000Base-T NIC and there all works fine. The thing is that this adapter is down
and goes up after few seconds after it is enslaved.
This patch calls bond_select_active_slave() in bond_enslave() function for modes
alb and tlb and makes sure that the current active slave is set up properly even
when the slave state is already up. Tested on both systems, works fine.
Notice: The same problem can maybe also occrur in mode 8023AD but I'm unable to
test that.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gianfar uses a hardware header FCB for offloading. However when used
with bridging or IP forwarding, TX skb might not have enough headroom
for the FCB. Reallocate skb for such cases.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bumps the driver release date to March 25th 2009
and release version to 0.22.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the second PHY address which is strapped
to be at PHY address 3 instead of 2.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a way to provide the MAC address for ax88796 devices from
their platform data. Boards might decide to set the address
programmatically, taken from boot tags or other sources.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to the ax88796 ethernet driver to take IRQ flags
given by the platform_device definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID for a new variant of the 82574 adapter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi, Pls accept this patch to cleanup rx/tx rate calculations as follows:
- check for jiffies wraparound
- remove typecast of a denominator
- do rate calculation only in workqueue context periodically
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the bug reported in
http://bugzilla.kernel.org/show_bug.cgi?id=11681.
"Lots of device drivers register a 'struct device_driver' with
the '.bus' member set to '&platform_bus_type'. This is wrong,
since the platform_bus functions expect the 'struct device_driver'
to be wrapped up in a 'struct platform_driver' which provides
some additional callbacks (like suspend_late, resume_early).
The effect may be that platform_suspend_late() uses bogus data
outside the device_driver struct as a pointer pointer to the
device driver's suspend_late() function or other hard to
reproduce failures."(Lothar Wassmann)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update myri10ge firmware headers to firmware version 1.4.41.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed unused variable dev
Signed-off-by: vibi sreenivasan <vibi_sreenivasan@cms.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On m68k:
| drivers/net/dnet.c: In function 'dnet_readw_mac':
| drivers/net/dnet.c:36: error: implicit declaration of function 'writel'
| drivers/net/dnet.c:43: error: implicit declaration of function 'readl'
| drivers/net/dnet.c: In function 'dnet_probe':
| drivers/net/dnet.c:873: error: implicit declaration of function 'ioremap'
| drivers/net/dnet.c:873: warning: assignment makes pointer from integer without a cast
| drivers/net/dnet.c:939: error: implicit declaration of function 'iounmap'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following build error:
CC ucc_geth.o
ucc_geth.c: In function 'ucc_geth_probe':
ucc_geth.c:3644: error: implicit declaration of function 'uec_mdio_bus_name'
make[2]: *** [ucc_geth.o] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver just read "reg" property for constructing MDIO
bus IDs, but this won't work when we'll start using "ranges = <>" in
the device tree, so this will pop up:
Freescale PowerQUICC MII Bus: probed
sysfs: duplicate filename 'mdio@520' can not be created
------------[ cut here ]------------
Badness at c00cb6b8 [verbose debug info unavailable]
NIP: c00cb6b8 LR: c00cb6b8 CTR: c001271c
REGS: cf82fc10 TRAP: 0700 Not tainted (2.6.29-rc7-03702-g7ccd10f)
MSR: 00029032 <EE,ME,CE,IR,DR> CR: 42044022 XER: 20000000
TASK = cf81fbd0[1] 'swapper' THREAD: cf82e000
GPR00: c00cb6b8 cf82fcc0 cf81fbd0 0000003b 00000e42 ffffffff 00004000 00000e42
GPR08: c03cb0fc c03bfbdc 00000e42 c03cac50 22044022 1006a2bc 0ffcb000 00000000
GPR16: 0ffc04b0 0ffc5a40 00000000 0ffc79a8 0f7863a8 00000004 00000000 00000000
GPR24: c033a6a8 d1014520 cf85e840 cf82fd08 cf87cf2c cf82fcd8 cf85dea8 ffffffef
NIP [c00cb6b8] sysfs_add_one+0x4c/0x54
LR [c00cb6b8] sysfs_add_one+0x4c/0x54
Call Trace:
[cf82fcc0] [c00cb6b8] sysfs_add_one+0x4c/0x54 (unreliable)
[cf82fcd0] [c00cbc18] create_dir+0x58/0xc0
[cf82fd00] [c00cbcc0] sysfs_create_dir+0x40/0x70
[cf82fd20] [c0159388] create_dir+0x28/0x78
[cf82fd30] [c0159824] kobject_add_internal+0x98/0x13c
[cf82fd50] [c0159e98] kobject_add+0x60/0x98
[cf82fd80] [c018a480] device_add+0x98/0x2ac
[cf82fda0] [c01a2380] mdiobus_register+0xbc/0x1c0
[cf82fdc0] [c019f31c] fsl_pq_mdio_probe+0x284/0x2a0
[cf82fe00] [c0223814] of_platform_device_probe+0x5c/0x84
...
This patch fixes the issue by translating the "reg" property to a full
address, and thus avoids the duplicate names.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN8710 and LAN8720 are two new 10/100 ethernet PHY models. The two
share the same phy id, this patch adds it to the smsc phy driver.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
ucc_geth: Fix oops when using fixed-link support
dm9000: locking bugfix
net: update dnet.c for bus_id removal
dnet: DNET should depend on HAS_IOMEM
dca: add missing copyright/license headers
nl80211: Check that function pointer != NULL before using it
sungem: missing net_device_ops
be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
be2net: replenish when posting to rx-queue is starved in out of mem conditions
bas_gigaset: correctly allocate USB interrupt transfer buffer
smsc911x: reset last known duplex and carrier on open
sh_eth: Fix mistake of the address of SH7763
sh_eth: Change handling of IRQ
netns: oops in ip[6]_frag_reasm incrementing stats
net: kfree(napi->skb) => kfree_skb
net: fix sctp breakage
ipv6: fix display of local and remote sit endpoints
net: Document /proc/sys/net/core/netdev_budget
tulip: fix crash on iface up with shirq debug
virtio_net: Make virtio_net support carrier detection
...
Remove duplicated #include in drivers/net/atl1c/atl1c.h.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b1c4a9dddf ("ucc_geth: Change
uec phy id to the same format as gianfar's") introduced a regression
in the ucc_geth driver that causes this oops when fixed-link is used:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0151270
Oops: Kernel access of bad area, sig: 11 [#1]
TMCUTU
NIP: c0151270 LR: c0151270 CTR: c0017760
REGS: cf81fa60 TRAP: 0300 Not tainted (2.6.29-rc8)
MSR: 00009032 <EE,ME,IR,DR> CR: 24024042 XER: 20000000
DAR: 00000000, DSISR: 20000000
TASK = cf81cba0[1] 'swapper' THREAD: cf81e000
GPR00: c0151270 cf81fb10 cf81cba0 00000000 c0272e20 c025f354 00001e80
cf86b08c
GPR08: d1068200 cffffb74 06000000 d106c200 42024042 10085148 0fffd000
0ffc81a0
GPR16: 00000001 00000001 00000000 007ffeb0 00000000 0000c000 cf83f36c
cf83f000
GPR24: 00000030 cf83f360 cf81fb20 00000000 d106c200 20000000 00001e80
cf83f360
NIP [c0151270] ucc_geth_open+0x330/0x1efc
LR [c0151270] ucc_geth_open+0x330/0x1efc
Call Trace:
[cf81fb10] [c0151270] ucc_geth_open+0x330/0x1efc (unreliable)
[cf81fba0] [c0187638] dev_open+0xbc/0x12c
[cf81fbc0] [c0187e38] dev_change_flags+0x8c/0x1b0
This patch fixes the issue by removing offending (and somewhat
duplicate) code from init_phy() routine, and changes _probe()
function to use uec_mdio_bus_name().
Also, since we fully construct phy_bus_id in the _probe() routine,
we no longer need ->phy_address and ->mdio_bus fields in
ucc_geth_info structure.
I wish the patch would be a bit shorter, but it seems like the only
way to fix the issue in a sane way. Luckily, the patch has been
tested with real PHYs and fixed-link, so no further regressions
expected.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a locking bug in the dm9000 driver. It calls
request_irq() without setting IRQF_DISABLED ... which is
correct for handlers that support IRQ sharing, since that
behavior is not guaranteed for shared IRQs. However, its
IRQ handler then wrongly assumes that IRQs are blocked.
So the fix just uses the right spinlock primitives in the
IRQ handler.
NOTE: this is a classic example of the type of bug which
lockdep currently masks by forcibly setting IRQF_DISABLED
on IRQ handlers that did not request that flag.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that most network device drivers in (all but one in x86_64 allmodconfig)
support net_device_ops. Expose it as a configuration parameter. Still
need to address even older 32 bit drivers, and other arch before
compatiablity can be scheduled for removal in some future release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pre-existing net_device_stats in network_device struct.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose routines so drivers can hook. Only set ptrs in netdev
if using old compat code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace struct in ieee with current net_device_stats, so no longer
need get_stats hook
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, make ethtool_ops const as it should be, and get rid
of useless cast.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, make ethtool_ops const as it should be, and get rid
of useless cast.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to use existing net_device_stats.
This driver,
has bad style,
of using commas,
when brackets should be used...
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use net_device_ops for usbnet device, and export for use
by other derived drivers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default handler for net_device_stats already does same thing.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculate a score for each 1000 IRQs:
- TX completions are worth 1 point
- RX completions are worth 4 if merged using LRO or 2 otherwise
Reduce moderation if the score is less than 10000, down to a minimum
of 5 us. Increase moderation if the score is more than 20000, up to
the specified maximum.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug this function works around only applies to the first set of
page-mapped registers; other pages can be written without locking.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, reading the legacy interrupt status register can
acknowledge an event queue whose attention flag has not yet been set
in the register. Until we service this event queue it will not
generate any more interrupts. Therefore, as a secondary check, poll
the next slot in each active event queue whose flag is not set.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet parser used in the TX data path for locating checksum
fields can lose synchronisation with the TX queue manager when
handling packets that look like IPv4 but are too short (17-32 bytes).
Work around this by padding to 33 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb driver was using map_single to map the skbs and then unmap_page to
unmap them. This update changes that so instead uses skb_dma_map and
skb_dma_unmap.
In addition the next_to_watch member of the buffer_info struct was being
set uneccesarily. I removed the spots where it was set without being needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if there are no multicast addresses programmed into the PF then
the VFs cannot have their multicast filters reset. This change makes it so
the code path that updates vf multicast is always called along with the pf
updates.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb was previously setting up all of the timer members itself. It is
easier to just call setup_timer and reduce the calls to one line.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes IGB_DESC_UNUSED and replaces it with a function call
instead in order to cleanup some of the ugliness introduced by the macro.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 82575 is fed 802.1q packets, it chokes with
an error of the form:
igb 0000:08:00.1 partial checksum but proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out with the correct hardware checksum.
Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution. This patch is
based upon his work.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
IBM EMAC driver performs device reset (drivers/net/ibm_newemac/core.c:
emac_probe() -> emac_init_phy() -> emac_reset()) before registering
appropriate net_device (emac_probe() -> register_netdev()), so
net_device name contains raw format string during EMAC reset ("eth%d").
If the case of reset timeout, emac_report_timeout_error() function is
called to report an error. The problem is this function uses net_device
name to report device related, which is not correct, as a result in the
kernel log buffer we see:
eth%d: reset timeout
The solution is to print device_node full_name instead. After applying
the patch proposed, error string is like the following:
/plb/opb/ethernet@ef600e00: reset timeout
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ixgbe to use net_device_ops properly.
Rather than changing the select_queue function pointer
just check the flag.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1577ecef76 ("netdev: Merge UCC
and gianfar MDIO bus drivers") broke the TSEC TBI PHY support: the
driver now refuses to probe TBI MDIO buses as it doesn't know about
"fsl,gianfar-tbi" compatible entry, and thus _probe() fails with
-ENODEV status.
Fix this by adding "fsl,gianfar-tbi" to the list of known Gianfar
MDIO buses.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 4826857f1b ("gianfar: pass the
proper dev to DMA ops") introduced this build breakage:
CC drivers/net/gianfar.o
drivers/net/gianfar.c: In function 'gfar_suspend':
drivers/net/gianfar.c:552: error: 'struct gfar_private' has no member named 'dev'
drivers/net/gianfar.c: In function 'gfar_resume':
drivers/net/gianfar.c:601: error: 'struct gfar_private' has no member named 'dev'
make[2]: *** [drivers/net/gianfar.o] Error 1
Fix this by converting suspend and resume routines to use
gfar_private->ndev.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables support for the new Intel 82552 adapter (new PHY paired
with the existing MAC in the ICH7 chipset). No new features are added to
the driver, however there are minor changes due to updated registers and a
few workarounds for hardware errata.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When merging into Jeff's tree:
commit 5f66f20806
Author: Arthur Jones <ajones@riverbed.com>
Date: Thu Mar 19 01:13:08 2009 +0000
e1000e: allow tx of pre-formatted vlan tagged packets
We lost one line, this fixes that missing
piece...
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicated #include in drivers/net/dnet.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The watchdog will schedule an interrupt to help make sure queues are
cleaned in the case when an interrupt is missed, most likely due to very
high load. On 82599, there are extra interrupt registers to account for
the larger number of MSI-X vectors (64 total for 82599 vs. 18 total for
82598). These must be taken into account when performing this operation in
the watchdog.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool isn't reporting the support level of WoL for 82599 KX4 devices.
While the device does support WoL, ethtool was never updated to properly
report the level of support, nor will it allow ethtool to modify the type
of packets to listen for.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82598's PCI bus reporting on driver load was broken after 82599 merged.
This results in incorrect reporting, and an erroneous warning message
that the 82598 is in a PCIe slot that isn't fast enough to run 10GbE.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code updates ixgb so that it can use the skb_dma_map/unmap functions
to map the buffers. In addition it also updates the tx hang logic to use
time_stamp instead of dma to determine if it has detected a tx hang.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with igb, when the e1000e driver is fed 802.1q
packets with hardware checksum on, it chokes with an
error of the form:
checksum_partial proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out wiht the correct hardware checksum.
Thanks to Kand Ly <kand@riverbed.com> for discovering the
issue and the coming up with a solution. This patch is
based upon his work.
Fixups from Stephen Hemminger <shemminger@vyatta.com> and
Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a few issues I noticed in e1000e. These include a double free
of the skb if mapping fails, and the fact that context descriptors appear
to be left in the descriptor ring after the failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID and related support for 82583 mac.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Radheka Godse <radheka.godse@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpu_to_le16 here looks suspicious to me, I don't think we need it
because put_unaligned_le16 also does this.
I don't currently have any big endian hardware with a PCI bus available
to test on, so I haven't been able to verify this.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the generic eth_mac_addr function with one that
also updates the hardware mac address registers. It also renames the
existing smsc911x_set_mac_address function to
smsc911x_hw_set_mac_address for clarity.
Newer LAN911x and all LAN921x devices also support changing the mac
address while the device is running, which is useful for some bonding
modes.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vast majority of bit constants in this driver are defined in the
header file, but TX and RX status word bits are not. This patch (which
should make no functional change) defines these, to make the driver
slightly more readable.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sungem driver only got partially converted to net_device_ops.
Since this could cause bugs, please push this to 2.6.29
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to reconfigure vlan-ids during an i/f down/up cycle
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to replenish the rx-queue when it is in a starved
state (due to out-of-mem conditions)
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc911x_phy_adjust_link is called periodically by the phy layer (as
it's run in polling mode), and it only updates the hardware when it sees
a change in duplex or carrier. This patch clears the last known values
every time the interface is brought up, instead of only when the module
is loaded.
Without this patch the adjust_link function never updates the hardware
after an ifconfig down; ifconfig up. On a full duplex link this causes
the tx error counter to increment, even though packets are correctly
transmitted, as the default MAC_CR register setting is for half duplex.
The tx errors are "no carrier" errors, which should be ignored in
full-duplex mode. When MAC_CR is set to "full duplex" mode they are
correctly ignored by the hardware.
Note that even with this patch the tx error counter can increment if
packets are transmitted between "ifconfig up" and the first phy poll
interval. An improved solution would use the phy interrupt with phylib,
but I haven't managed to make this work 100% robustly yet.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Address of SH_TSU_ADDR and ARSTR of SH7763 was wrong.
This revise it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling of IRQ of the SH7763/SH7764 CPU which sh_eth supported was
changed.
This revises it for this change.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be passing the of_platform device struct into the DMA ops as
its the one that has the archdata setup to know which low-level DMA ops we
should be using (not the net_device one). This isn't an issue until we
expect the archdata to be setup correctly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port's link is down (except to driver restart) and the port is
configured for auto sensing, we try to sense port link type (Ethernet
or InfiniBand) in order to determine how to initialize the port. If
the port type needs to be changed, all mlx4 for the device interfaces
are unregistered and then registered again with the new port
types. Sensing is done with intervals of 3 seconds.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Tulip is currently doing request_irq before it has done its
initialization. This is usually not a problem because it hasn't
enable interrupts yet, but with DEBUG_SHIRQ on, we call the irq handler
when registering the interrupt as a sanity check.
This can result in a NULL ptr dereference, so call tulip_init_ring
before request_irq, and add a free_ring function to do the freeing
now shared with tulip_close.
Tested with a shell loop running ifup, ifdown in a loop a few hundred
times with DEBUG_SHIRQ on.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Make NetworkManager work with virtio_net
For now the semantics are simple: There is always carrier.
This allows a seamless experience with e.g., qemu/kvm
where NetworkManager just configures and sets up
everything automagically.
If/when a generally agreed-upon way to control
carrier on/off in the emulator/hypervisor level
emerges, it will be trivial to extend the driver
to support that too, but for now even this 2-liner
makes user experience that much better.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects an omission from the following commit:
commit f0c76d6177
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Wed Jul 2 18:21:58 2008 -0700
bonding: refactor mii monitor
The un-refactored code checked the link speed and duplex of
every slave on every pass; the refactored code did not do so.
The 802.3ad and balance-alb/tlb modes utilize the speed and
duplex information, and require it to be kept up to date. This patch
adds a notifier check to perform the appropriate updating when the slave
device speed changes.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary check (skb_padto does the same check)
Remove unnecessary duplicate variable
Remove unnecessary clearing of padded part of skb.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSI-X handler was chosen before the call to pci_enable_msix().
If MSI-X was not available, the wrong MSI-X handler would be used in
INTA mode. This would cause a screaming interrupt problem because
INTA would not be cleared by the MSI-X handler.
Fixed by assigning MSI-X handler after pci_enable_msix() returns
successfully. Also update version to 1.9.3.
Thomas Chenault <thomas_chenault@dell.com> helped us find this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warnings, by using integer firmware types.
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_load_firmware':
drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
user needs to see this message even if debugging disabled
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hopefully the register contents will guide us to why this failure occured
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_clear_station_table will be called every time rxon called.
In this function ucode_key_table is set to 0 even though a static
WEP security is set. This will cause in many warning and might be
an issue if dynamic WEP is set. This patch make sure we keep track
of all existing static WEP when this function is called.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During preparation of TX we create DMA mapping to TX command as part of
preparing the TFD. This mapping needs to be cleared at the time TFD is
freed.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 uses iwl_tx_cmd_complete to reclaim the unused buffers of the queue.
iwl_tx_cmd_complete in turn call the iwl_hcmd_queue_reclaim which will
unmap the dma mapping to tx_cmd and frees the memory.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the bug 1900 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1900
Issues:
Throughput and success ratio calculations were not done properly.
Number of retries were exceeding 16.
Fix:
Patch fixes above issues by doing window calculations inline with iwlwifi
Patch adds sanity check to limit number of retries to 16.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_led's structure from iwlwifi.
Patch also removes CONFIG_IWL3945_LEDS flag from Kconfig as 3945's led
support will now be enabled if user selects CONFIG_IWLWIFI_LEDS.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
error is:
iwl3945-base.c:545:5: warning: symbol 'iwl3945_set_dynamic_key' was not
declared. Should it be static?
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When iwlwifi driver receive fixed rate debugfs command, validate the
antenna selection, if the selection is invalid, report the valid antenna
choice and do not set the rate scale table to fixed rate. Otherwise, set
the entire rate scale table to the fixed rate request by the user. this
validation can prevent sysassert happen in uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when perform rate scaling, in tx status function, checking for
IEEE80211_TX_STAT_AMPDU flag instead of IEEE_TX_CTL_AMPDU flag to perform
AMPDU rate scaling operation.
IEEE80211_TX_CTL_AMPDU was set by mac80211 for aggregation pkt. But when
iwlwifi receive the tx status reply, it reset the flag to following
info->flags = IEEE80211_TX_STAT_ACK;
info->flags |= IEEE80211_TX_STAT_AMPDU;
it causes the rate-scaling to not work for aggregation pkt if we checking
for IEEE80211_TX_CTL_AMPDU flag.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During rate scaling, checking for 0 retry count before decrement
the count by 1, this can avoid the retry count to become 255 (0xff),
which will cause the rate to drop faster than what we expect during good
condition (receive 0 retry packet). also change the algorithm to make
the rate not drop faster than what we like.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the MLME handshaking complete and tx aggregation started for the
tid. Do not send unnecessary turn on aggregation request to mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding more Radio information when displaying
rate_scale_table. This can help to understand how many antenna and the
current RF condition such as SISO, MIMO2, MIMO3.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when display rate_scale_table debugfs information, also display valid tx
antenna information, this will help user to select correct antenna when
issue fixed rate debugfs command
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before: 1099 errors, 93 warnings, 2854 lines checked
After: 19 errors, 47 warnings, 2976 lines checked
The big bulk of this is code indent and over 80 character lines
(Lindent did this part) Other changes are foo * bar spacing, and
trailing whitespace.
v2: Cleans up ill-indented comments. Subsequently, this reduces the
number of warnings, too. Thanks to Joe Perches for pointing this out!
v3: Ran the whole file through Lindent first... which does most of
the work for me. :) Again, thanks to Joe Perches for this.
This is my final answer!
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a driver for Marvell 88w8xxx TOPDOG PCI/PCIe wireless parts.
This initial version supports the 88w8687 802.11b/g PCIe part on
channels 1-11, and only STA mode is currently implemented.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must not disable ACK sending in this case since it would break
normal station operations. In addition, clarify the comment about AP
mode to make more sense.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the sparse complaints:
drivers/net/wireless/ath9k/eeprom.c:1407:5: warning: symbol
'ath9k_hw_4k_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:1436:19: warning: symbol
'eep_4k_ops' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2808:5: warning: symbol
'ath9k_hw_def_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2837:19: warning: symbol
'eep_def_ops' was not declared. Should it be static?
CC [M] drivers/net/wireless/ath9k/eeprom.o
CHECK drivers/net/wireless/ath9k/mac.c
CC [M] drivers/net/wireless/ath9k/mac.o
CHECK drivers/net/wireless/ath9k/calib.c
drivers/net/wireless/ath9k/calib.c:883:6: warning: symbol 'ar9285_clc'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not a fatal message, hitting it simply means we're
going to tell the upper layers to slow their horses down but
as we make more descriptors available we let the show continue
by waking up the queues in ath_wake_mac80211_queue().
We downgrade this as otherwise we fill up your kernel log with
messages which can be common under heavy traffic.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a module parameter for mac80211_hwsim regulatory testing.
This module parameter is designed specifically to help test the
different possible types of driver specific regulatory requests
and also helps to test world roaming, all without any hardware.
If you want to just simply test different alpha2s just use the userspace
regulatory request as this won't buy you anything new.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so we can later inform userspace who set the
regulatory domain and provide details of the request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used as we can always just assume the first
regulatory domain set will _always_ be a static regulatory
domain. REGDOM_SET_BY_CORE will be the first request from
cfg80211 for a regdomain and that then populates the first
regulatory request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before: 881 errors, 265 warnings, 4507 lines checked
After: 114 errors, 273 warnings, 4548 lines checked
This was mostly "space required after that ',' (ctx:VxV)".
Also a fair number of whitespace, code indent, and C99 comment cleanups.
New warnings introduced are all "line over 80 character"
md5sums are identical, as I skipped any fixes which may have altered the resulting binary.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate table would not have been chosen before the interface
has been brought up. Reading 'rcstat' in this case would result
in an oops, fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 expects the driver to fill in the starting
sequence number of an ADDBA request to initiate TX aggregation.
IEEE80211_TX_CTL_AMPDU would be set for frames only after a
successful ADDBA exchange, but we have to increment the
internal sequence counter for the normal(non-AMPDU) data frames proerly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI was not being initialized correctly for all HW variants.
This patch fixes it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for Acer Ferrari 5000, and also specifies
the subsystem device ids for previously reported e-machines e510 and
Acer Aspire One A150.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put the device id-to-gpio mapping in a table to make it easier to add
new devices. The list of supported devices is unchanged.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move LED code out of base.c for clarity.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not touch mac parameter passed to ath5k_eeprom_read_mac unless
we are sure we have correct address. I.e. when returning error, do
not change it.
While at it, use '= {}' compiler trick for memsetting mac_d.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make some structures const to place them in .rodata, since we won't
change them.
Most important parts of objdump -h:
- 0 .text 00011170
+ 0 .text 00011140
- 5 .rodata 0000828e
+ 5 .rodata 0000895e
- 13 .data 00000560
+ 13 .data 00000110
- 14 .devinit.data 00000260
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
device name was changed from 100 to 1000
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add check for new association to ease reading.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Passing frames with a bad FCS to the user is an optional feature.
However it doesn't work reliable and strangely not in the native monitor mode?!
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hopefully nothing controversial here, since the driver hasn't been touched in a while!
Before: 36 errors, 6 warnings, 482 lines checked
After: 0 errors, 3 warnings, 485 lines checked
This was nearly all trailing whitespace, * and parenthesis spacing, and code indent changes.
md5sum of object file before and after are identical.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch improves range and connection stability in AR9285.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove obsolete enums from ipw2x00/ieee80211.h, they are not used anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use IE definitions from linux/ieee80211.h and drop the appropriate enum
from ipw2x00/ieee80211.h
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove several duplicated defines from ipw2x00/ieee80211.h which are
also available in linux/ieee80211.h.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace all remaining occurrences of CONFIG_IEEE80211_DEBUG with
CONFIG_LIBIPW_DEBUG in libipw to allow debug output again.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_radio_{en,dis}able is only compiled if RFKILL is enabled, but it is
required by the 'ath9k_wiphy_select' function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath9k/debug.c: In function 'read_file_wiphy':
drivers/net/wireless/ath9k/debug.c:377: error: implicit declaration of
function 'put_unaligned_le32'
drivers/net/wireless/ath9k/debug.c:378: error: implicit declaration of
function 'put_unaligned_le16'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath9k/ahb.c: In function 'ath_ahb_probe':
drivers/net/wireless/ath9k/ahb.c:136: error: 'aphy' undeclared (first
use in this function)
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current macro is wrong, because detects some AR5416 devices as an
AR9100 device. The AR5416 devices would have performance issues after
this change, because the contents of the ar5416 specific and of the
ar9100 specificinitval arrays are swapped. Fortunately we can correct
this with the rename of the arrays simply.
Changes-licesed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All other version checking macros are in a common location within the
reg.h file. The AR_SREV_9100_OR_LATER macro is wrong currently, but will
be fixed with the next patch.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we have two different versions of this macros. Because they
would have to do the same thing, we should simplify and merge them.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix AR9285 1.1 and 1.2 version check macro.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the initvalues for AR9285 chipset and also adds
periodic PA offset caliberation.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
accessing RXBUF list in ath_rx_cleanup may cause panic if
ath_descdma_setup fails even before RXBUF list is initialized.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can sleep for memory during init time and so allocating rx buffers,
descriptro buffers with GFP_KERNEL should help us to get rid of transient
alloc fails.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ACME Inc. is now selling a dual band radio.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables power save support on all p54 devices.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds SoftLED support for all p54 devices.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disabling the receiver logic with P54_FILTER_TYPE_RX_DISABLED is not
supported by all firmwares. However we have an alternative: hibernation.
And the only side effect - so far - is a bit less power consumption. WIN!
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces most printk(KERN_* "") with their by dev_* analogue.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All three drivers (p54pci, p54usb and p54spi) are implementing the
same functionality three times. So, why not put it into the shared library?!
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes a problem when the (Soft)LED stayed on after the module was unloaded.
It turned out that the USB core disables all endpoints before calling the disconnect method.
So it was impossible to switch off the radio & LEDs.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver are trying to create an 'ath9k' directory in debugfs for each
device currently. If there are more than one device in the system, the
second try will always fail.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently part of support for FW caching is unconditionally compiled
in even if it is never used. Consistently remove caching support if
not requested by user.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd_op_tx() must not return an arbitrary error value since that can
leave mac80211 trying to retransmit the frame and with the extra data
pushed into the beginning of the skb on every attempt, this will end up
causing a kernel panic (skb_under_panic from skb_push call). This can
happen, e.g., when ejecting the device when associated.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All 802.11n PCI devices (Cardbus, PCI, mini-PCI) require
serialization of IO when on non-uniprocessor systems. PCI
express devices not not require this.
This should fix our only last standing open ath9k kernel.org
bugzilla bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=12110
A port is probably required to older kernels and I can work on
that.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most fasync implementations do something like:
return fasync_helper(...);
But fasync_helper() will return a positive value at times - a feature used
in at least one place. Thus, a number of other drivers do:
err = fasync_helper(...);
if (err < 0)
return err;
return 0;
In the interests of consistency and more concise code, it makes sense to
map positive return values onto zero where ->fasync() is called.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
It fails on the following systems:
- RTL8169sc/8110sc (XID 18000000)
reported by Tim Durack <tdurack@gmail.com> (x86)
- RTL8169sb/8110sb (XID 10000000)
reported by Mikael Pettersson <mikpe@it.uu.se> (ARM)
The patch appeared to work on x86 for the following systems:
RTL8169sb/8110sb 10000000 PCI (EXT)
RTL8110s 04000000 PCI (EXT)
RTL8102e 24a00000 PCI-E (LOM)
RTL8168c/8111c 3c2000c0 PCI-E (LOM)
RTL8168b/8111b 38000000 PCI-E (LOM)
RTL8168b/8111b 38000000 PCI-E (EXT)
The patch exposes two problems:
1) while not completely wrong, mac addresses are not read correctly
from the EEPROM
2) the MAC address registers are not correctly set
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
It shortens the code and fixes the current pci_unmap leak with
padded skb reported by Dave Jones.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L0s workaround should be moved into a pci quirk and so it is not
necessary in the driver. This update removes the L0s workaround from the
igb driver.
This was the second half of the PCI quirk patch that Matthew Wilcox did
not pick up when he picked up the quirk patch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To mark all features and bugfixes submitted since 4.0.11.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the load balancing capability of firmware
and hardware to spray traffic into different cpus through
separate rx msix interrupts.
The feature is being enabled for NX3031, NX2031 (old) will be
enabled later. This depends on msi-x and compatibility with
msi and legacy is maintained by enabling single rx ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove max_ prefix from ring sizes, since they don't really
represent max possible sizes.
o cleanup naming of rx ring types (normal, jumbo, lro).
o simplify logic to choose rx ring size, gig ports get half
rx ring of 10 gig ports.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detach network interface on PCI suspend and recreate hardware
context after resumes.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup a bit of whitespace, add some function header comments, and fix a
few comments around the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx DMA unit should be disabled when bringing the device down. Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel. In those cases, we'd rather
fail gracefully instead of a panic. Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans up the following pieces of the Rx initialization path:
- Enable the ECC memory fault interrupt in OTHER causes.
- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled. We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.
- Fix the RSS initialization path to not stomp on DCB accidentally. When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status. The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.
Solution: call napi_add before calling request_irq
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt models using EITR have changed in 82599. The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't. This patch fixes all the cases where EITR
handling is different than 82598.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 mistakenly enabled drop on Rx queues in the packet buffer. The
default mode should be store-and-forward from the FIFO.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly. In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
