According to the gen6 docs, only the DP_A port (on-CPU eDP) still uses
the old IBX bit shift for the link training pattern setup bits.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The obvious counterpart to is_pch_edp(). Convert existing instances of
the idiom to the new routine.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
SPD frames are actually type 0x83, not just 0x3.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Misc fixes based on tests with an infoframe analyzer:
- checksum *does* include header bytes
- DIP enable & AVI infoframe are tied together in hw, so disable both
and make sure AVI frames are enabled first
- use every vsync flag for SPD frames to avoid reserved value in
frequency field when enabling both AVI & SPD
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=40281.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
DPCD 1.1+ adds some automated test infrastructure support. Add support
for reading the IRQ source and jumping to a test handling routine if
needed. Subsequent patches will handle particular tests; this patch
just ACKs any requested tests by default.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Read link status first, followed by the full DPCD receiver cap field
rather than just the first 8 bytes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The previous code was confused about units, which is pretty reasonable
given that the units themselves are confusing.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The commit 47356eb672 introduced a
mechanism to record the backlight level only at disabling time, but it
also introduced a regression. Since intel_lvds_enable() may be called
without disabling (e.g. intel_lvds_commit() calls it unconditionally),
the backlight gets back to the last recorded value. For example, this
happens when you dim the backlight, close the lid and open the lid,
then the backlight suddenly goes to the brightest.
This patch fixes the bug by recording the backlight level always
when changed via intel_panel_set_backlight(). And,
intel_panel_{enable|disable}_backlight() call the internal function not
to update the recorded level wrongly.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
With the tracing code in there they are far too big to inline.
.text savings compared to a non force inline kernel:
i915_restore_display 4393 12036 +7643
i915_save_display 4295 11459 +7164
i915_handle_error 2979 6666 +3687
i915_driver_irq_handler 2923 5086 +2163
i915_ringbuffer_info 458 1661 +1203
i915_save_vga - 1200 +1200
i915_driver_irq_uninstall 453 1624 +1171
i915_driver_irq_postinstall 913 2078 +1165
ironlake_enable_drps 719 1872 +1153
i915_restore_vga - 1142 +1142
intel_display_capture_error_state 784 2030 +1246
intel_init_emon 719 2016 +1297
and more ...
[AK: these are older numbers, with the new SNB forcewake checks
it will be even worse]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Belongs in PCH enable instead. The duplication is worrying and the
specs explicitly list transcoder select *after* actual PLL enable, which
doesn't occur until later.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The watermark reg for the third pipe is in an unusual offset; add
support for it and set watermarks for 3 pipe configs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
At the point where we check, we can't do much about the failure, but it
can aid debugging. Note that the auto-train override bit will be reset
as part of normal mode setting with this patch if a pipe ever does get
stuck, but that's consistent with the workaround for CPT provided by the
hardware team. This patch helped catch the fact that the pipe wasn't
running in the !composite sync FDI case on my IVB SDV, so has already
shown to be useful.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Transcoder A will always use PLL A and transcoder B will use PLL B. But
transcoder C could use either, so always mask the select bits off before
or'ing in a new value.
Reported-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The cursor regs have moved around, add the offsets and new macros for
getting at them.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We can have more than just A and B these days.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add two new fields to the intel_crtc struct for 3 pipe support: no_pll
and use_pll_a. The no_pll field is only set on the 3rd pipe to indicate
that it doesn't have a PLL of its own and so shouldn't try to write the
main PLL regs. The use_pll_a field controls which PLL pipe 3 will
share, A or B. The core code will try to share PLLs with whichever pipe
has the same timings, rejecting the mode set if none is found. This
means that pipe 3 must always be set after one of the other pipes has
been configured with real PLL settings.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add a couple of checks now that we're using the 3rd transcoder:
1) make sure the transcoder PLL enable bit is set for the transcoder
in question
2) when checking actual PLL enable, use the selected PLL number rather
than the transcoder number (they could be different now)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Just a cleanup to make the mode_set function more manageable.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Well almost anyway. IVB has 3 planes, pipes, transcoders, and FDI
interfaces, but only 2 pipe PLLs. So two of the pipes must use the same
pipe timings (e.g. 2 DP plus one other, or two HDMI with the same mode
and one other, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add a macro for accessing the two pipe PLLs and add a check to make sure
we don't access a non-existent one in the enable/disable functions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
It's needed for 3 pipe support as well as just regular functionality
(e.g. DisplayPort).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Adam Jackson <ajax@redhat.com>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
v2 by danvet: Use a new flag to flush the render target cache on gen6+
(hw reuses the old write flush bit), as suggested by Ben Widawsdy.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: this seems to fix cairo-perf-trace hangs on my snb]
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
"STALL_AT_SCOREBOARD" is much clearer than "STALL_EN" now that there are
several different kinds of stalls. Also, "INSTRUCTION_CACHE_INVALIDATE"
is a lot easier to understand at a glance than the terse "IS_FLUSH."
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: use INVALIDATE for ro cache flags for more consistency]
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Not all PIPE_CONTROLs have a length of 2, so remove it from the #define
and make each invocation specify the desired length.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: implement style suggestion from Ben Widawsdy]
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Idle the GPU before doing any unmaps. We know if VT-d is in use through
an exported variable from iommu code.
This should avoid a known HW issue.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
[Description from: Daniel Vetter]
I've just discussed this quickly with Chris on irc and it's probably
best to just kill the list_empty early bailout. gpu_idle isn't a
fastpath, so who cares. One candidate where we emit commands to the ring
without adding anything onto these lists is e.g. pageflip. There are
probably more.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
We currently only round up the userspace size to the next page. We
assume that userspace hasn't made a mistake and requested a zero-length
gem object and all through our internal code we then presume that every
object is backed by at least a single page. Fix that oversight and
report EINVAL back to userspace if they try to create a zero length
object.
[danvet: This fixes tests/gem_bad_length]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Use the helper function already employed by the pwrite/pread
functions.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Fixes tests/gem_tiled_pread on my snb. I know, mesa doesn't use this
on gen6+, but I also hate failing testcases.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
The rps disabling code wasn't properly cancelling outstanding work
items. Also add a comment that explains why we're not racing with
the work item that could unmask interrupts - that piece of code
confused me quite a bit.
v2: Ben Widawsky pointed out that the first patch would deadlock
(and a few lesser problems). All corrected.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This patch closes the following race:
We get a PM interrupt A, mask it, set dev_priv->iir = PM_A and kick of the
work item. Scheduler isn't grumpy, so the work queue takes rps_lock,
grabs pm_iir = dev_priv->pm_iir and pm_imr = READ(PMIMR). Note that
pm_imr == pm_iir because we've just masked the interrupt we've got.
Now hw sends out PM interrupt B (not masked), we process it and mask
it. Later on the irq handler also clears PMIIR.
Then the work item proceeds and at the end clears PMIMR. Because
(local) pm_imr == pm_iir we have
pm_imr & ~pm_iir == 0
so all interrupts are enabled.
Hardware is still interrupt-happy, and sends out a new PM interrupt B.
PMIMR doesn't mask B (it does not mask anything), PMIIR is cleared, so
we get it and hit the WARN in the interrupt handler (because
dev_priv->pm_iir == PM_B).
That's why I've moved the
WRITE(PMIMR, 0)
up under the protection of the rps_lock. And write an uncoditional 0
to PMIMR, because that's what we'll do anyway.
This races looks much more likely because we can arbitrarily extend
the window by grabing dev->struct mutex right after the irq handler
has processed the first PM_B interrupt.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Quoting Chris Wilson's more concise description:
"Ah I think I see the problem. As you point out we only mask the current
interrupt received, so that if we have a task pending (and so IMR != 0) we
actually unmask the pending interrupt and so could receive it again before the
tasklet is finally kicked off by the grumpy scheduler."
We need the hw to issue PM interrupts A, B, A while the scheduler is hating us
and refuses to run the rps work item. On receiving PM interrupt A we hit the
WARN because
dev_priv->pm_iir == PM_A | PM_B
Also add a posting read as suggested by Chris to ensure proper ordering of the
writes to PMIMR and PMIIR. Just in case somebody weakens write ordering.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This is general TMDS detect, not HDMI specifically.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
I can't think of any sensible reason to limit this to a mask of 0x0f,
ie, SDVO_OUTPUT_{TMDS,RGB,CVBS,SVID}0.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
I have no evidence for this byte being used this way, and lots of
counterexamples. Restore the struct to its empirical definition and
patch up gmbus setup to match.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
If an older userspace passes in a smaller arg than the current kernel
ioctl arg struct, then extra fields should be initialized to zero
rather than passing random data to the DRM driver.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
FB scratch indices are dword indices, but we were treating
them as byte indices. As such, we were getting the wrong
FB scratch data for non-0 indices. Fix the indices and
guard the indexing against indices larger than the scratch
allocation.
Fixes memory corruption on some boards if data was written
past the end of the FB scratch array.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Dave Airlie <airlied@redhat.com>
Tested-by: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are a number of fixes in mainline required for code in -next,
also there was a few conflicts I'd rather resolve myself.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/radeon/evergreen.c
drivers/gpu/drm/radeon/r600.c
drivers/gpu/drm/radeon/radeon_asic.h
If ret is non-zero then we don't initialize the struct which leaks
stack information to user space.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These variables get allocated twice so the first allocation is a
memory leak.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The intent here was to return an error code, but instead the code
returns the number of bytes remaining (that weren't copied).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Settings in this table reflect the physical panel/connector rather
than the internal dig encoding.
v2: fix typo for DRM_MODE_CONNECTOR_VGA case.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's handled via external clock. It should already be protected
by the external ss flag, but add an explicit check just in case.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
llano has fully routeable dig encoders similar to DCE3.2 while
ontario has a hardcoded mapping similar to DCE4.0.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r600-NI shared the same blit suspend code. Clean it up
and make it a shared function.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
factor out most of evergreen blit code and use the refactored code
from r600 that is now common for both r600 and evergreen
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
blit copy functions deal with GPU pages, not CPU pages,
so rename the variables and parameters accordingly
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
reorganize the code such that only the primitives (i.e., the functions
that load the CP ring) are hardware specific; dynamically link the
primitives in a (new) pointer structure inside r600_blit at
blit initialization time so that the functions that control the blit
operations can be made common for r600 and evergreen parts
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Lots of new (and hopefully useful) benchmark. Load the driver
with radeon_benchmark=<test_number> and enjoy. Among tests
added are VRAM to VRAM blits and blits with buffer size sweeps.
The latter can be from GTT to VRAM, VRAM to GTT, and VRAM to VRAM
and there are two types of sweeps: powers of two and (probably
more interesting) buffers sizes that correspond to common modes.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
factor out repeated code into functions
fix units in which the throughput is reported (megabytes per second
and megabits per second make sense, others are kind of confusing)
make report more amenable to awk and friends (e.g. whitespace is
always the separator, unit is separated from the number, etc)
add #defines for some hard coded constants
besides "beautification" this reorg is done in preparation
for writing more elaborate benchmarks
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
some 3d register bits look like magic in r600 blit functions
use predefined constants to make it more intuitive what they are
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
some bits in 3D registers used by blit functions look like
magic and this is hard to follow; change them to a little bit
more meaningful pre-defined constants
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Covert 4k pages to multiples of 64x64x4 tiles.
This is also more efficient than a scanline based
approach from the MC's perspective.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Covert 4k pages to multiples of 64x64x4 tiles.
This is also more efficient than a scanline based
approach from the MC's perspective.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is no point in re-doing in post_xfer all the initialization
that was already done by pre_xfer. Instead, only do the work which
differs from pre_xfer.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
in case of using two drivers such as fimd and hdmi controller that
they have their own hardware interrupt, drm framework doesn't provide
pipe number corresponding to it. so the pipe should be set to event's
from specific crtc.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this patch adds the following comments and code clean.
- add comment of exynos_drm_crtc_apply() call at page flip time.
- add comment that when exynos_drm_fbdev_reinit() is called,
why num_connector is 0 and also the framebuffers should be destroyed.
- remove buf_off member from struct exynos_drm_overlay because this member
isn't used anymore.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this patch solves the problem that fb_helper is released
when exynos_drm_fbdev_reinit() was called. if this function call
is ok then just return.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
sub drivers should refer to its own device object to access
its own context.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
buffer addess is set to shadow register and then applied to
real register at vsync front porch time.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this patch adds common members to overlay structure and
makes each driver such as fimd or hdmi driver set them to
its own structure.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This shrinks the sizes of a lot of functions in the radeon driver
dramatically.
With a non force inline + -Os kernel this is default anyways.
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With this patch I'm only about 50k larger with DRM debugging
enables (why is that enabled by default?!?), and slightly
smaller without.
[airlied: moved r100.c additions to radeon_ring.c]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the dropped inlines gccs starts warning about genuinely unused
functions. Remove r600_bpe_from_format, evergreen_cs_track_validate_cb,
evergreen-cs_packet_next_is_pkt3_nop which are all unused.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes
evergreen_cs_parse 4080 23124 +19044
and others compared to a non force inline kernel.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes kernel panics when running the vbltest from the drm repo. We
can't just skip initializing the vblank system since it sets up certain
state for us, see: "vmwgfx: Enable use of the vblank system."
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure we null the display private, make sure we catch and
handle vblank failing to init and don't call vblank_cleanup if
we haven't initialized the display system.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the panel is powered up, there's no need to delay for the 'off'
interval when turning the panel on.
Signed-off-by: Keith Packard <keithp@keithp.com>
This eliminates a fairly long delay when power sequencing newer
hardware
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like the same pcie gen2 speed initialization for
Evergreen also works on Cayman and seems to come up fine,
so enable it if the module parameter says so
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Enabling pcie gen2 speed was skipped for Northern Islands
AISCs, although it looks like it works just fine with the same
initialization sequence used for evergreen.
According to Alex D. gen2 init was skipped to prevent a crash
that has been caused by some other bug that has been
fixed in the meantime; so now it should be safe to enable it.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also improve a bit on the Kconfig help.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure the device is processing the fifo when these functions are
called in case they might sleep waiting for an event.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a way to send DRM events down the gpu fifo by attaching them to
fence objects. This may be useful for Xserver swapbuffer throttling and
page-flip done notifications.
Bump version to 2.2 to signal the availability of the FENCE_EVENT ioctl.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This function will be used also by the upcoming fence event code,
so break it out and add a comment about the functionality.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a card wasn't PCIE, we always set the DMA mask to 32 bits.
This is only applies to the old rage128/r1xx gart block on
early radeon asics (~r1xx-r4xx). Newer PCI and IGP cards
can handle 40 bits just fine.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Chen Jie <chenj@lemote.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The value of RADEON_DEBUGFS_MAX_NUM_FILES has been used to
specify the size of an array, each element of which looks
like this:
struct radeon_debugfs {
struct drm_info_list *files;
unsigned num_files;
};
Consequently, the number of debugfs files may be much greater
than RADEON_DEBUGFS_MAX_NUM_FILES, something that the current
code ignores:
if ((_radeon_debugfs_count + nfiles) > RADEON_DEBUGFS_MAX_NUM_FILES) {
DRM_ERROR("Reached maximum number of debugfs files.\n");
DRM_ERROR("Report so we increase RADEON_DEBUGFS_MAX_NUM_FILES.\n");
return -EINVAL;
}
This commit fixes this make, and accordingly renames:
RADEON_DEBUGFS_MAX_NUM_FILES
to:
RADEON_DEBUGFS_MAX_COMPONENTS
Signed-off-by: Michael Witten <mfwitten@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When force == false, we don't do load detection in the connector
detect functions. Unforunately, we also return the previous
connector state so we never get disconnect events for DVI-I, DVI-A,
or VGA. Save whether we detected the monitor via load detection
previously and use that to determine whether we return the previous
state or not.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41561
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
DVI-D and HDMI-A are digital only, so there's no need to
attempt analog load detect. Also, skip bail before the
!force check, or we fail to get a disconnect events.
The next patches in the series attempt to fix disconnect
events for connectors with analog support (DVI-I, HDMI-B,
DVI-A).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41561
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 9b9fe724 accidentally used RADEON_GPIO_EN_* where
RADEON_GPIO_MASK_* was intended. This caused improper initialization
of I2C buses, mostly visible when setting i2c_algo_bit.bit_test=1.
Using the right constants fixes the problem.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Jerome Glisse <j.glisse@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Contexts, surfaces and streams allocate persistent kernel memory as the
direct result of user-space requests. Make sure this memory is
accounted as graphics memory, to avoid DOS vulnerabilities.
Also take the TTM read lock around resource creation to block
switched-out dri clients from allocating resources.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no good reason to turn off the eDP force VDD bit synchronously
while probing devices; that just sticks a huge delay into all mode
setting paths. Instead, queue a delayed work proc to disable the VDD
force bit and then remember when that fires to ensure that the
appropriate delay is respected before trying to turn it back on.
Signed-off-by: Keith Packard <keithp@keithp.com>
We need to check eDP VDD force and panel on in several places, so
create some simple helper functions to avoid duplicating code.
Signed-off-by: Keith Packard <keithp@keithp.com>
The return value was unused, so just stop doing that.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This value doesn't come directly from the VBT, and so is rather
specific to the particular DP output.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store the panel power sequencing delays in the dp private structure,
rather than the global device structure. Who knows, maybe we'll get
more than one eDP device in the future.
From the eDP spec, we need the following numbers:
T1 + T3 Power on to Aux Channel operation (panel_power_up_delay)
This marks how long it takes the panel to boot up and
get ready to receive aux channel communications.
T8 Video signal to backlight on (backlight_on_delay)
Once a valid video signal is being sent to the device,
it can take a while before the panel is actuall
showing useful data. This delay allows the panel
to get something reasonable up before the backlight
is turned on.
T9 Backlight off to video off (backlight_off_delay)
Turning the backlight off can take a moment, so
this delay makes sure there is still valid video
data on the screen.
T10 Video off to power off (panel_power_down_delay)
Presumably this delay allows the panel to perform
an orderly shutdown of the display.
T11 + T12 Power off to power on (panel_power_cycle_delay)
So, once you turn the panel off, you have to wait a
while before you can turn it back on. This delay is
usually the longest in the entire sequence.
Neither the VBIOS source code nor the hardware documentation has a
clear mapping between the delay values they provide and those required
by the eDP spec. The VBIOS code actually uses two different labels for
the delay values in the five words of the relevant VBT table.
**** MORE LATER ***
Look at both the current hardware register settings and the VBT
specified panel power sequencing timings. Use the maximum of the two
delays, to make sure things work reliably. If there is no VBT data,
then those values will be initialized to zero, so we'll just use the
values as programmed in the hardware. Note that the BIOS just fetches
delays from the VBT table to place in the hardware registers, so we
should get the same values from both places, except for rounding.
VBT doesn't provide any values for T1 or T2, so we'll always just use
the hardware value for that.
The panel power up delay is thus T1 + T2 + T3, which should be
sufficient in all cases.
The panel power down delay is T1 + T2 + T12, using T1+T2 as a proxy
for T11, which isn't available anywhere.
For the backlight delays, the eDP spec says T6 + T8 is the delay from the
end of link training to backlight on and T9 is the delay from
backlight off until video off. The hardware provides a 'backlight on'
delay, which I'm taking to be T6 + T8 while the VBT provides something
called 'T7', which I'm assuming is s
On the macbook air I'm testing with, this yields a power-up delay of
over 200ms and a power-down delay of over 600ms. It all works now, but
we're frobbing these power controls several times during mode setting,
making the whole process take an awfully long time.
Signed-off-by: Keith Packard <keithp@keithp.com>
The encoders are supposedly fully routeable, but changing the mapping
doesn't always seem to take. Using a hardcoded mapping is much more
reliable.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41366
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Any call to intel_dp_sink_dpms must ensure that the panel has power so
that the DP_SET_POWER operation will be correctly received. The only
one missing this was in intel_dp_prepare.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP i2c initialization code does a couple of i2c transactions,
which means that an eDP panel must be powered up.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Talking to the eDP DDC channel requires that the panel be powered
up. Wrap both the EDID and modes fetch code with calls to turn the vdd
power on and back off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On eDP, DDC requires panel power, but turning that on uses the panel
power sequencing timing values fetch from the DPCD data.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the panel is already off, we'll need to turn VDD on to execute the
(useless) DPMS off code. Yes, it would be better to just not do any of
this, but correctness, and *then* performance.
Signed-off-by: Keith Packard <keithp@keithp.com>
The HPD pin is not reliable for detecting whether a monitor
is connected or not. Skip HPD and just use DDC or load
detection.
Fixes phantom VGA connected bugs.
[Michel: fixes phantom VGA bugs on his llano system.]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
If there are error flags in the aux status, retry the transaction.
This makes aux much more reliable, especially on llano systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch is a DRM Driver for Samsung SoC Exynos4210 and now enables
only FIMD yet but we will add HDMI support also in the future.
this patch is based on git repository below:
git://people.freedesktop.org/~airlied/linux.git
branch name: drm-next
commit-id: 88ef4e3f4f
you can refer to our working repository below:
http://git.infradead.org/users/kmpark/linux-2.6-samsung
branch name: samsung-drm
We tried to re-use lowlevel codes of the FIMD driver(s3c-fb.c
based on Linux framebuffer) but couldn't so because lowlevel codes
of s3c-fb.c are included internally and so FIMD module of this driver has
its own lowlevel codes.
We used GEM framework for buffer management and DMA APIs(dma_alloc_*)
for buffer allocation so we can allocate physically continuous memory
for DMA through it and also we could use CMA later if CMA is applied to
mainline.
Refer to this link for CMA(Continuous Memory Allocator):
http://lkml.org/lkml/2011/7/20/45
this driver supports only physically continuous memory(non-iommu).
Links to previous versions of the patchset:
v1: < https://lwn.net/Articles/454380/ >
v2: < http://www.spinics.net/lists/kernel/msg1224275.html >
v3: < http://www.spinics.net/lists/dri-devel/msg13755.html >
v4: < http://permalink.gmane.org/gmane.comp.video.dri.devel/60439 >
v5: < http://comments.gmane.org/gmane.comp.video.dri.devel/60802 >
Changelog v2:
DRM: add DRM_IOCTL_SAMSUNG_GEM_MMAP ioctl command.
this feature maps user address space to physical memory region
once user application requests DRM_IOCTL_SAMSUNG_GEM_MMAP ioctl.
DRM: code clean and add exception codes.
Changelog v3:
DRM: Support multiple irq.
FIMD and HDMI have their own irq handler but DRM Framework can regiter
only one irq handler this patch supports mutiple irq for Samsung SoC.
DRM: Consider modularization.
each DRM, FIMD could be built as a module.
DRM: Have indenpendent crtc object.
crtc isn't specific to SoC Platform so this patch gets a crtc
to be used as common object.
created crtc could be attached to any encoder object.
DRM: code clean and add exception codes.
Changelog v4:
DRM: remove is_defult from samsung_fb.
is_default isn't used for default framebuffer.
DRM: code refactoring to fimd module.
this patch is be considered with multiple display objects and
would use its own request_irq() to register a irq handler instead of
drm framework's one.
DRM: remove find_samsung_drm_gem_object()
DRM: move kernel private data structures and definitions to driver folder.
samsung_drm.h would contain only public information for userspace
ioctl interface.
DRM: code refactoring to gem modules.
buffer module isn't dependent of gem module anymore.
DRM: fixed security issue.
DRM: remove encoder porinter from specific connector.
samsung connector doesn't need to have generic encoder.
DRM: code clean and add exception codes.
Changelog v5:
DRM: updated fimd(display controller) driver.
added various pixel formats, color key and pixel blending features.
DRM: removed end_buf_off from samsung_drm_overlay structure.
this variable isn't used and end buffer address would be
calculated by each sub driver.
DRM: use generic function for mmap_offset.
replaced samsung_drm_gem_create_mmap_offset() and
samsung_drm_free_mmap_offset() with generic ones applied
to mainline recentrly.
DRM: removed unnecessary codes and added exception codes.
DRM: added comments and code clean.
Changelog v6:
DRM: added default config options.
DRM: added padding for 64-bit align.
DRM: changed prefix 'samsung' to 'exynos'
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make surfaces swappable. Make sure we honor the maximum amount of surface
memory the device accepts. This is done by potentially reading back surface
contents not used by the current command submission and storing it
locally in buffer objects.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use a list for resources referenced during command submission, instead of
an array.
As long as we don't implement parallell command submission this works fine
and simplifies things a bit.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously, query results could be placed in any buffer object, but since
we didn't allow pinned buffer objects, query results could be written when
that buffer was evicted, corrupting data in other buffers.
Now, require that buffers holding query results are no more than two pages
large, and allow one single pinned such buffer. When the command submission
code encounters query result structures in other buffers, the queries in the
pinned buffer will be finished using a query barrier for the last hardware
context using the buffer. Also if the command submission code detects
that a new hardware context is used for queries, all queries of the previous
hardware context is also flushed. Currently we use waiting for a no-op
occlusion query as a query barrier for a specific context.
The query buffer is also flushed and unpinned on context destructions,
master drops and before scanout bo placement.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The execbuf utils may call reference on NULL fence objects.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add / fix some function comments.
Don't move out an fbdev framebuffer when unused. Just unpin.
Only have a single function that computes a SVGAGuestPtr from the buffer's
current placement, and make it more versatile by accepting a
struct ttm_buffer_object
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we hae screen objects we are allowed to place the overlay source
in the GMR area, do this as this will save precious VRAM.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since 3D requires HWv8 and screen objects is always available on those
hosts we only need the screen objects path for surfaces.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On lower versions, the way we mix 2D and 3D may be too slow.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
More preparation for Screen Object support.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In preperation for screen objects, still leaves the delayed workqueue
for surface updates in place.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will make it easier to execute commands operating on user-space
resources but generated by the kernel.
JB: Added tracking if the sw_context was called from the kernel or userspace.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Most asics just use the hw default value which requires
no explicit programming. For those that need a different
value, the vbios will program it properly. As such,
there's no need to program these registers explicitly
in the driver. Changing MC_SHARED_CHREMAP requires a reload
of all data in vram otherwise its contents will be scambled.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=40103
v2: drop now unused channel_remap functions.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Apart from the obvious cleanup, this should make the line
cursor_end = x - xorigin + w;
correct now.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes cursor disappearing prematurely when moving off a top/left edge which
is not located at the desktop top/left edge.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The mouse cursor hotspot calculation when the cursor is partially off the
top or left side of the screen was off by one.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=41158
Signed-off-by: Nicholas Miell <nmiell@gmail.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only disable the pipe if the monitor is physically
disconnected. The previous logic also disabled the
pipe if the link was trained.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41248
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous code could potentially loop forever. Limit
the number of DP aux defer retries to 4 for native aux
transactions, same as i2c over aux transactions.
Noticed by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Brad Campbell <lists2009@fnarfbargle.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
An incorrect ordering in the error checking code lead
to DP aux defer being skipped in the aux native write
path. Move the bytes transferred check (ret == 0)
below the defer check.
Tracked down by: Brad Campbell <brad@fnarfbargle.com>
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41121
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Brad Campbell <brad@fnarfbargle.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The VDD force bit is turned on before touching the panel, but if it
was enabled, there was no call to turn it back off. Add a call.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid any question about locked registers by just writing the unlock
pattern with every write to the register.
Signed-off-by: Keith Packard <keithp@keithp.com>
Verify that the eDP VDD is on, either with the panel being on or with
the VDD force-on bit being set.
This demonstrates that in many instances, VDD is not on when needed,
which leads to failed EDID communications.
Signed-off-by: Keith Packard <keithp@keithp.com>
Adam Jackson