Commit graph

310 commits

Author SHA1 Message Date
Mikael Pettersson
56fe23d5a7 pdc202xx_new: PLL detection fix
Fix a bitmask typo in the pdc202xx_new PLL frequency detection code
which causes it to truncate an intermediate difference to 26 bits
instead of the correct 30 bits (the PLL's bitwidth).

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-09-11 22:28:37 +02:00
Bartlomiej Zolnierkiewicz
58e47bb176 via82cxxx: add Arima W730-K8 and other rebadgings to short cables list
Port of Alan's patch for pata_via.c.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-09-11 22:28:37 +02:00
Daniel Exner
03e6f489b3 pata_ali/alim15x3: override 80-wire cable detection for Toshiba S1800-814
Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.

Signed-off-by: Daniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-09-11 22:28:36 +02:00
Sergei Shtylyov
2808b0a96a hpt366: UltraDMA filter for SATA cards (take 2)
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method.  In order to achieve that, do
the following changes:

- install the method for all chips, not only HPT36x/370 and improve the code
  formatting by killing the extra tabs while at it;

- add to the end of the 'switch' statement in the method cases for HPT372[AN]
  and HPT374 chips upon which the known SATA cards are based;

- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
  behave correctly;

- move the HPT370[A] cases below the HPT36x case for consistency.

While at it, replace the explicit UltraDMA mode masks with ATA_UDMA* constants
all over the driver...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bob Ham <rah@bash.sh>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-09-11 22:28:36 +02:00
Sergei Shtylyov
7293136810 hpt366: fix PCI clock detection for HPT374 (take 4)
HPT374 BIOS seems to only save f_CNT register value for the function #0 before
re-tuning DPLL (that causes the driver to report obviously distorted f_CNT for
the function #1) -- fix this by always reading the saved f_CNT register value
from the function #0 in the driver's init_chipset() method.
While at it, introduce 'chip_type' for holding the 'struct hpt_info' field
of the same name and replace the structure assignment with memcpy()...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-09-11 22:28:35 +02:00
Sergei Shtylyov
35198234a2 pdc202xx_new: fix PCI refcounting
The driver erroneously "lets go" the mate IDE chip in init_setup_pdc20270()
when ide_setup_pci_devices() call succeeds -- fix this, and drop a couple of
useless assignments in this function while at it...

Bart: keep "findev" variable initialization to silence gcc

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-09-11 22:28:34 +02:00
Joseph Chan
b311ec4ae8 [libata, IDE] add new VIA bridge to VIA PATA drivers
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-09-10 22:06:01 -04:00
Bartlomiej Zolnierkiewicz
76e1faa7cf hpt34x: fix CONFIG_HPT34X_AUTODMA=n handling
Programming DMA mode may destroy current PIO mode setting so if
CONFIG_HPT34X_AUTODMA=n (the default case) make ide_tune_dma() fail
early by disabling all host DMA masks and re-tune PIO mode.

This fix doesn't help with the driver being broken but is needed
for some other changes.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-20 22:42:57 +02:00
Bartlomiej Zolnierkiewicz
88b47040f8 triflex: add missing ->dma_base check
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-20 22:42:56 +02:00
Bartlomiej Zolnierkiewicz
e98d6e50be pdc202xx_old: add missing ->dma_base check
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-20 22:42:56 +02:00
Bartlomiej Zolnierkiewicz
01cc643ae3 pdc202xx_new: add missing ->dma_base check
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.

Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-20 22:42:56 +02:00
Bartlomiej Zolnierkiewicz
f7b0d2df2f cs5530: add missing ->dma_base check
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.

Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-20 22:42:56 +02:00
Bartlomiej Zolnierkiewicz
1116fae5fd ide: config_drive_for_dma() fixes
* Add DMA blacklist checking (->ide_dma_on check probably can go now).

* Add ->atapi_dma flag checking and remove no longer needed
  ns87415_ide_dma_check() from ns87415 host driver.

* Remove now needless __ide_dma_check() wrapper and symbol export.

* Check drive->autodma instead of hwif->autodma (there should be no changes in
  behavior as all users of config_drive_for_dma() set both ->autodma flags).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-20 22:42:55 +02:00
Bartlomiej Zolnierkiewicz
3fcece6691 scc_pata: PIO fixes
* Use pio == 255 == "auto-tune" in scc_config_drive_for_dma() instead of
  forcing PIO4 on PIO fallback.  Fix comment while at it.

* Rename scc_tuneproc() to scc_tune_pio() and add scc_tuneproc() wrapper.
  Move finding of the best PIO mode and setting of transfer mode on the device
  to the new wrapper.

* Fix scc_tune_chipset() to tune PIO modes.  Do a small cleanup while at it.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:46 +02:00
Bartlomiej Zolnierkiewicz
0c8de52d76 piix/slc90e66: fix PIO1 handling in ->speedproc method (take 2)
* Don't call {piix,slc90e66}_dma_2_pio() for PIO modes in
  {piix,slc90e66}_tune_chipset().

* Add PIO1 handling to {piix,slc90e66}_tune_chipset().

* Bump driver version.  

v2:
* Remove PIO modes from {piix,slc90e66}_dma_2_pio(), they are no longer needed
  there (Noticed by Sergei)

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:46 +02:00
Bartlomiej Zolnierkiewicz
8b6b33be32 jmicron: PIO fixes
* Set transfer mode on the device in jmicron_tuneproc(),
  also add pio == 255 == "auto-tune" handling.

* Use jmicron_tuneproc() in jmicron_config_drive_for_dma().

* Remove no longer needed config_jmicron_chipset_for_pio().

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:46 +02:00
Bartlomiej Zolnierkiewicz
68aaf81503 it8213: PIO fixes (take 2)
* Rename it8213_tuneproc() to it8213_tune_pio() and add it8213_tuneproc()
  wrapper.  Move finding of the best PIO mode to the new wrapper.

* Add setting of transfer mode on the device to it8213_tuneproc().

* Don't call it8213_dma_2_pio() for PIO modes in it8213_tune_chipset().

* Use it8213_tuneproc() in it8213_config_drive_for_dma().

v2:
* Remove PIO modes from it8213_dma_2_pio(), they are no longer needed there
  (Noticed by Sergei)

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:46 +02:00
Bartlomiej Zolnierkiewicz
bc0b0b5c4b cs5535: PIO fixes
* Fix cs5535_tuneproc() to pass PIO transfer mode value instead of PIO mode
  number to cs5535_set_speed() (fixes random PIO timings being programmed
  and a possible OOPS).  Do a little cleanup while at it.

* Fix cs5535_set_speed() to check if the mate device is present (fixes PIO0
  taskfile timings being used if there is no other device on the cable).

* Use cs5535_tuneproc() in cs5535_dma_check().  The old code had the same
  issue as cs5535_tuneproc() and add additionally caused 0x00-0x04 transfer
  mode values (== default PIO, default PIO w/ IORDY + two invalid values)
  being set on the device instead of values 0x08-0x0c (XFER_PIO_[0,4]).

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:45 +02:00
Bartlomiej Zolnierkiewicz
070224339b cs5520: fix PIO auto-tuning in ->ide_dma_check method
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:45 +02:00
Meelis Roos
b37c6b842b ide: fix runtogether printk's in cmd64x IDE driver
Fix a couple of runtogether printks in cmd64x.c IDE driver by adding 
proper newlines.

Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:44 +02:00
David Lamparter
1955f6814f sis5513: Add FSC Amilo A1630 PCI subvendor/dev to laptops
Recognise the FSC Amilo A1630's incarnation of a SiS5513 chip as laptop to
get UDMA100 support.

Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Lionel Bouton <Lionel.Bouton@inet6.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:44 +02:00
Bartlomiej Zolnierkiewicz
8663fd6d0d alim15x3: Correct HP detect
Direct port of Alan's fix for pata_ali.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:43 +02:00
Jordan Crouse
32a70a817a ide: Fix an overrun found in the CS5535 IDE driver
As found by the Coverity checker, and reported by Adrian Bunk, this
fixes a overrun error in the CS5535 IDE driver.  Somebody got a little
excited with the if() statement - the CS5535 only supports UDMA 0-4.

Bart:
Not a bug per se since the upper layer will never feed this function
with speed > XFER_UDMA_4 (thanks to ->ultra_mask being set to 0x1f).

Worth fixing anyway.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-08-01 23:46:42 +02:00
Al Viro
0bd8496b59 drivers/ misc __iomem annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-26 11:11:57 -07:00
Bartlomiej Zolnierkiewicz
4099d14322 ide: add PIO masks
* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:59 +02:00
Bartlomiej Zolnierkiewicz
6a824c92db ide: remove ide_find_best_pio_mode()
* Add ->host_flags to ide_hwif_t to store ide_pci_device_t.host_flags,
  assign it in setup-pci.c:ide_pci_setup_ports().

* Add IDE_HFLAG_PIO_NO_{BLACKLIST,DOWNGRADE} to ide_pci_device_t.host_flags
  and teach ide_get_best_pio_mode() about them.  Also remove needless
  !drive->id check while at it (drive->id is always present).

* Convert amd74xx, via82cxxx and ide-timing.h to use ide_get_best_pio_mode()
  and then remove no longer needed ide_find_best_pio_mode().

There should be no functionality changes caused by this patch.

Acked-by: Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:58 +02:00
Bartlomiej Zolnierkiewicz
2134758d2a ide: drop "PIO data" argument from ide_get_best_pio_mode()
* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
  and convert all users accordingly.

* Remove no longer needed ide_pio_data_t.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:58 +02:00
Bartlomiej Zolnierkiewicz
7dd00083b1 ide: add ide_pio_cycle_time() helper (take 2)
* Add ide_pio_cycle_time() helper.

* Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers
  (previously cycle time given by the device was only used for "pio" == 255).

* Remove no longer needed ide_pio_data_t.cycle_time field.

v2:
* Fix "ata_" prefix (Noticed by Jeff).

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:56 +02:00
Bartlomiej Zolnierkiewicz
31c4df441c sc1200: remove stale Power Management code
* Nowadays core IDE code handles restoring of PIO and DMA modes
  (ide-io.c:ide_start_power_step() etc) so remove open-coded version
  from sc1200_resume().

  There should be no change in behavior because settings done by
  sc1200_resume() were always overridden by generic_ide_resume()
  and ide_{start,stop}_power_step().

* Bump driver version.

Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:56 +02:00
Bartlomiej Zolnierkiewicz
1c164acf50 serverworks: fix DMA
The driver used to depend on BIOS settings for deciding whether it is OK
to use DMA.  However it seems that BIOS doesn't always handle all cases
correctly so just let IDE core to decide about this.  It should be a safe
thing to do now, after the driver went through heavy bugfixing.

Thanks for bugreport and testing the patch goes out to Sven Niedner.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:56 +02:00
Bartlomiej Zolnierkiewicz
1880a8d7f2 serverworks: always tune PIO
* Always set ->autotune so PIO gets correctly auto-tuned (previously
  ->autotune was only set when ->dma_base wasn't available, however
  ->ide_dma_check()/->speedproc() was always trying to tune PIO when
  tuning DMA).

* Move code responsible for programming chipset for PIO mode from
  svwks_tune_chipset() to svwks_tune_pio().  Don't tune PIO when tuning
  DMA (this is no longer needed since ->autotune is always set now).

* Handle PIO modes early in svwks_tune_chipset() so DMA configuration
  registers don't get cleared when programming PIO mode.

* Bump driver version.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:56 +02:00
Bartlomiej Zolnierkiewicz
a5d8c5c834 ide: add ide_pci_device_t.host_flags (take 2)
* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
  and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.

* Add IDE_HFLAG_SINGLE flag for single channel devices.

* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
  and remove no longer needed ide_pci_device_t.channels field.

v2:
* Fix issues noticed by Sergei:
  - correct code alignment in scc_pata.c
  - s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:55 +02:00
Bartlomiej Zolnierkiewicz
2229833c13 ide: add ide_dev_has_iordy() helper (take 4)
* Add ide_dev_has_iordy() helper and use it sl82c105 host driver.

* Remove no longer needed ide_pio_data_t.use_iordy field.

v2/v3:
* Fix issues noticed by Sergei:
  - correct patch description
  - fix comment in ide_get_best_pio_mode()

v4:
* Fix "ata_" prefix (Noticed by Jeff).

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:55 +02:00
Bartlomiej Zolnierkiewicz
342cdb6d47 ide: make ide_get_best_pio_mode() print info if overriding PIO mode
* Print info about overriding PIO mode in ide_get_best_pio_mode().

* Remove info about overriding PIO mode from cmd64{0,x} host drivers.

* Remove no longer needed ide_pio_data_t.overridden field.

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:55 +02:00
Bartlomiej Zolnierkiewicz
328dcbb636 siimage: PIO mode setup fixes (take 2)
* Add sil_tuneproc() wrapper for siimage_tuneproc() which also sets
  PIO mode on the device.

* Add missing ide_get_best_pio_mode() call to sil_tuneproc() so
  "pio" == 255 (autotune) is handled correctly (previously PIO0 was used)
  and "pio" values > 4 && < 255 are filtered to PIO4 (instead of PIO0).

* Add code limiting maximum PIO mode according to the pair device capabilities
  to sil_tuneproc().

* Convert users of config_siimage_chipset_for_pio() to use sil_tune_pio() and
  sil_tuneproc().  This fixes PIO fallback in siimage_config_drive_for_dma() to
  use max PIO mode available instead of PIO4 (config_siimage_chipset_for_pio()
  used wrong arguments for ide_get_best_pio_mode() and as a results always
  tried to set PIO4).

* Remove no longer needed siimage_taskfile_timing()
  and config_siimage_chipset_for_pio().

* Enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
  from siimage_speedproc()

* Bump driver version.

v2:
* Fix issues noticed by Sergei:
  - correct pair device check
  - trim only taskfile PIO to the slowest of the master/slave
  - enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
    from siimage_speedproc()
  - add TODO item for IORDY bugs
  - minor cleanups

Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:54 +02:00
Bartlomiej Zolnierkiewicz
485efc6cf5 atiixp: PIO mode setup fixes
* Split off exisiting atiixp_tuneproc() into atiixp_tune_pio()
  and then add setting device PIO mode to atiixp_tuneproc().

* Add missing ide_get_best_pio_mode() call to atiixp_tuneproc() so
  "pio" == 255 (autotune) is handled correctly and "pio" values > 4 && < 255
  are filtered to PIO4 (previously "pio" == 5 could result in wrong timings
  being used and "pio" values > 4 && < 255 in an OOPS).

* Handle PIO modes early in atiixp_speedproc() so save_mdma_mode[]
  doesn't get cleared.

* In atiixp_dma_check():
  - fix max_mode argument for ide_get_best_pio_mode()
  - don't call atiixp_dma_2_pio() so PIO1 doesn't get remapped to PIO0
  - use atiixp_tuneproc() instead of atiixp_speedproc()

* Bump driver version.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:54 +02:00
Alan Cox
9702b5d5c2 ide: Stop mapping ROMs
Various old IDE drivers go mapping ROM devices for no apparent reason and
without using the ROM mapping API we now have. They don't actually use
the ROM they map and the new libata drivers are happy without it being
mapped so rather than port them lets just junk it for the next -rc1.

Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:54 +02:00
Kou Ishizaki
4ae41ff887 scc_pata.c: Workaround for errata A308 (take 2)
Workaround for errata A308: turn down the UDMA mode and retry
the DMA command when the data lost condition is detected.

take2:
udma_filter() hook is used to limit ATAPI UDMA mode.

Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:53 +02:00
Kumar Gala
f644d47af3 scc_pata: Use inline function for eieio
Move to using inline function variant of eieio instead of inline assmebly.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: kou.ishizaki@toshiba.co.jp
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-20 01:11:53 +02:00
Randy Dunlap
694625c0b3 PCI: add pci_try_set_mwi
As suggested by Andrew, add pci_try_set_mwi(), which does not require
return-value checking.

- add pci_try_set_mwi() without __must_check
- make it return 0 on success, errno if the "try" failed or error
- review callers

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-11 16:02:11 -07:00
Auke Kok
44c10138fd PCI: Change all drivers to use pci_device->revision
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.

This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.

In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.

Compile tested with make all{yes,mod}config on x86_64 and i386.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-11 16:02:10 -07:00
Bartlomiej Zolnierkiewicz
bdab00b73d via82cxxx: backport short cables support from pata_via.c
Backport short cables support from pata_via.c.

This patch should allow UDMA > 2 modes on Acer Ferrari 3400.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2007-07-09 23:17:58 +02:00
Bartlomiej Zolnierkiewicz
f2befd9e80 sis5513: backport short cables support from pata_sis.c
Backport short cables support from pata_sis.c.

This patch allows UDMA > 2 modes on ASUS A6K.

Thanks to testing this patch goes out to Jiri Stavinoha.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2007-07-09 23:17:58 +02:00
Bartlomiej Zolnierkiewicz
95ba8c17bc alim15x3: backport short cables support from pata_ali.c
Backport short cables support from pata_ali.c and while at it cleanup
existing cable detection code.

This patch should allow UDMA > 2 modes on HP Pavilion N5430 and Fujitsu P2000.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2007-07-09 23:17:58 +02:00
Bartlomiej Zolnierkiewicz
7207626f47 piix: backport short cables support from ata_piix.c
Backport short cables support from ata_piix.c.

This patch should allow UDMA > 2 modes on:
- Acer 5602WLMi
- Acer 3682WLMi
- Asus W5F
- Acer Aspire 2023WLMi

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2007-07-09 23:17:58 +02:00
Bartlomiej Zolnierkiewicz
49521f97cc ide: add short cables support
This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter.  Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.

Next patches add automatic detection of some systems using short cables.

Changes:

* Rename hwif->udma_four to hwif->cbl and make it u8.

* Convert all existing users accordingly (use ATA_CBL_* defines while at it).  

* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().

* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2007-07-09 23:17:58 +02:00
Bartlomiej Zolnierkiewicz
75b1d97535 ide: convert ide_find_best_mode() users to use ide_max_dma_mode()
ide-timing.h:

* remove handling of DMA modes from ide_find_best_mode() and rename it to
  ide_find_best_pio_mode()

* drop no longer needed "map" argument from ide_find_best_pio_mode()
  and delete needless ->id check

* remove no longer needed XFER_SWDMA and XFER_UDMA* defines

au1xxx-ide.c:

* use ide_max_dma_mode() instead of ide_find_best_mode()

* remove needless CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA #ifdef

amd74xx.c:

* store UDMA masks in amd_ide_chip[] and while at it make "base" field
  to be u8 instead of unsigned long

* convert the driver to use UDMA masks from amd_ide_chip[]

* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
  of ide_find_best_mode()

* delete stale comment from amd74xx_ide_dma_check()

* remove no longer needed AMD_UDMA* defines

via82cxxx.c:

* remove unused DISPLAY_VIA_TIMINGS define

* store UDMA masks in via_isa_bridges[] and while at it make "flags" field
  to be u8 instead of u16

* convert the driver to use UDMA masks from via_isa_bridges[]

* use ide_max_dma_mode() and ide_find_best_pio_mode() instead
  of ide_find_best_mode()

* remove no longer needed VIA_UDMA* defines

pmac.c:

* use ide_max_dma_mode() instead of ide_find_best_mode()

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
2007-07-09 23:17:57 +02:00
Sergei Shtylyov
6d78013bfc aec62xx: kill speedproc() method wrapper (take 2)
There's no reason to have the speedproc() method wrapper for the two quite
different chip families, so just get rid of it.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:56 +02:00
Sergei Shtylyov
1b9da32a28 aec62xx: remove init_dma() method (take 2)
Get rid of the init_dma() method (which had no particular reason to exist) by
folding it into the init_hwif() method. While at it, also perform some cleanup
in the latter method:

- get rid of the useless clearing of hwif->autodma;

- fold the serialization code into one 'if' statement;

- fold setting the drives' 'autotune' and 'autodma' fields into the single
  statements...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:56 +02:00
Sergei Shtylyov
b1d19db4e7 aec62xx: rework init_setup_aec6x80()
Rework init_setup_aec6x80() so that it won't rewrite the constant name strings
anymore -- in order to do this:

- in aec62xx_init_one(), pass a local copy of 'struct pci_device_id' down the
  call chain;

- change the names for in aec62xx_chipsets[] to default to AEC-6280[R];

- override the 'name' field in init_setup_aec6x80() only if bit 4 of the DMA
  status register is set.

While at it, also change the 'udma_mask' field for AEC-6x80R chips in this
function and remove the code doing the same from the init_hwif() method...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-07-09 23:17:56 +02:00