Added the missing HDMI codec IDs for new Nvidia stuff.
Note that ID 0x17 isn't assigned to anything so far, as suggested by
Stephen.
[Modified to get rid of 0x17 by tiwai]
Signed-off-by: Richard Samson <samson.richard@gmail.com>
Acked-by: Acked-By: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is run after the DAPM widgets and routes are added, allowing setup
of things like jacks using the routes. The main card probe() is run before
anything else so can't be used for this purpose.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
These will be added after all devices are registered and allow most DAI
init functions in machine drivers to be replaced by simple data.
Regular controls are not supported as the registration function still
works in terms of CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This means that rather than adding the board specific DAPM widgets to a
random CODEC DAPM context they can be added to the card itself which is
a bit cleaner. Previously there only was one DAPM context and it was
tied to the single supported CODEC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
A CODEC pointer is optional (and is checked for in most contexts within
DAPM) - add checks to the few places where it was missed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than indirecting through the CODEC we can look the card up directly
from the card pointer in the DAPM context.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9081 IRQ output can be either active high or active low and can
support either CMOS or open drain modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
When choosing IMX_DMA flag, burtsizes are set to its default
value (0) which leads to driver malfunction. Change them to 4.
DSP_B interface needs additional flag to match DSP_B formats
as described in several codecs as wm8741 and aic3205.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the ADCs are provided with a clock as the previous patch
"ASoC: WM8994: Improve playback robustness" did not handle this case
properly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Since we began using the late clock disable functionality, ensure that
we don't disable the clock if any of the ADC or DAC paths are still
enabled. This happens when we have simultaneous playback and recording.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
It went AWOL in the multi-component conversion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
eukrea-tlv320: fix platform_name
ASoC: correct pxa AC97 DAI names
ALSA: hda - Add support for new IDT 92HD98 and 92HD99 codecs
ALSA: HDA: Add ideapad quirk for two Dell machines
ALSA: HDA: Add a new Conexant codec 506e (20590)
ALSA: usb-audio: fix oops due to cleanup race when disconnecting
ASoC: Hook wm_hubs micbiases up to CLK_SYS
ASoC: Correct definition of WM8903_VMID_RES_5K
ASoC: Fix WM8958 default microphone detection argument ordering
ALSA: HDA: Fix mic initialization in VIA auto parser
ALSA: fix one memory leak in sound jack
Get rid of users of of_platform_driver in drivers/sound. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes an error in the jack detection reporting,
causing the jack detection sometimes not to be reported
correctly to the input subsystem. It should apply to several
Realtek codecs.
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
tegra_dma_allocate_channel() returns NULL on errors, not an error pointer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Depending on the model and the presence of a TCO module, the number of
midi ports varies. Some have 1 port (MADIface), some have 2 (default),
with TCO, there are 3.
Don't hardcode the number of midi ports to initialize.
This patch also fixes a boot lockup on MADIface.
[Coding-style fixes by tiwai]
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In contrast to the PCIe version (RME AES), the PCI version (RME AES32)
has a different firmware revision.
This patch adds the missing PCI revision.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove unnecessary headers:
- mach/hardware.h in sgtl5000.c
- linux/i2c.h in sgtl5000.h
Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow input from microphone on remaining PowerBooks and iBooks with Tumbler.
Tested only with PowerBook G4 Gigabit Ethernet (PowerBook3,3).
[Fixed to use of_machine_is_compatible by tiwai]
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Patch below removes one to many "n's" in a word..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's a general move to use dev_pm_ops rather than bus specific functions
in order to facilitate work on the PM core. Do this conversion to WM2000.
The driver ought to be updated to work better in a multi-component model
but the mechanical conversion ensures that we avoid blocking PM core work
until that happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
commit f0fba2ad1b included a mistake
on the name of the platform in the snd_soc_dai_link structure.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The utilities will be required by every machine driver. Including the
utility object directly into every machine driver causes a build failure
if the modules are actually built into the kernel, since each will define
the symbols exported by the utility file. Solve this by moving the
utility object into a separate module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes the name of the control switch of a dapm route contains
spaces which makes it impossible to distinguish it from the source widget.
Add quotes around the names of the widgets to makes these parsable.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct names for pxa AC97 DAI are pxa2xx-ac97 and pxa2xx-ac97-aux. Fix
that for all PXA platforms.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removed the use of macros to obtain base address and DMA channel number.
Instead use the McBSP driver API's that passes base address and DMA
channel number to the client driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Also fix number of 92HD87 pins to exclude invalid pins.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're currently not passing anything and this will make the card and so on
more discoverable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Lately I sent patch that switched lfe with side in mixer for
acer-aspire-4930g. Then I connected 5.1 speaker system and noticed that
lfe slider wasn't working and that old lfe slider worked. What I'm doing
now is:
- reverting old patch
- adding internal lfe slider
- removing side as it is superfluous (ALC888S-VC is 7.1 but in fact
laptop can only do 5.1 and it is so in drivers for MS Windows)
Signed-off-by: Łukasz Wojniłowicz <lukasz.wojnilowicz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These two Dell machines have been reported working well with
the ideapad model.
BugLink: http://bugs.launchpad.net/bugs/723676
Cc: stable@kernel.org
Tested-by: David Chen <david.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conexant 506e/20590 has the same graph as the rest of the 5066 family.
BugLink: http://bugs.launchpad.net/bugs/723672
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Original patch by Dan Rosenberg <drosenberg@vsecurity.com> under commit
e68d3b316a. I'm copying his text here:
The SNDRV_HDSPM_IOCTL_GET_CONFIG_INFO ioctl in hdspm.c allow unprivileged
users to read uninitialized kernel stack memory, because several fields
of the hdspm_config struct declared on the stack are not altered
or zeroed before being copied back to the user. This patch takes care
of it.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fredrik Lingvall <fredrik.lingvall@gmail.com> has discovered wrong
frequency and sync detection on AES32. According to him, the provided
patch fixes these issues.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In contrast to the RME MADI card, coax/optical selection on the MADIface
is done via a physical switch located at the breakout box. Obviously,
the driver cannot switch ports in software.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Caused by two typos, no output channel mappings were assigned for
MADI/MADIface at double/quad speed.
The channel mapping is indeed identical to the single speed mapping, the
cards will simply use the first N channels.
Signed-off-by: Florian Faber <faber@faberman.de>
Signed-off-by: Fredrik Lingvall <fredrik.lingvall@gmail.com>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without calling an appropriate rule, AES/AES32 cards would announce a
theoretical channel count of 64 (HDSPM_MAX_CHANNELS), leading to the
already known bug:
[37422.640481] ------------[ cut here ]------------
[37422.640487] WARNING: at sound/pci/rme9652/hdspm.c:5449
snd_hdspm_ioctl+0x18f/0x202 [snd_hdspm]()
[37422.640489] Hardware name: PRIMERGY RX100 S6
[37422.640490] BUG? (info->channel >= hdspm->max_channels_in)
[37422.640492] Modules linked in: snd_hdspm snd_seq_midi ipmi_watchdog
ipmi_poweroff ipmi_si ipmi_devintf ipmi_msghandler i2c_i801 e1000e
snd_rawmidi power_meter [last unloaded: snd_hdspm]
[37422.640501] Pid: 22231, comm: jackd Tainted: G D W
2.6.36-gentoo-r5 #5
[37422.640502] Call Trace:
[37422.640508] [<ffffffff8103db3a>] warn_slowpath_common+0x80/0x98
[37422.640511] [<ffffffff8103dbe6>] warn_slowpath_fmt+0x41/0x43
[37422.640514] [<ffffffff81034306>] ? get_parent_ip+0x11/0x42
[37422.640518] [<ffffffffa0055763>] snd_hdspm_ioctl+0x18f/0x202
[snd_hdspm]
[37422.640522] [<ffffffff813fd626>] snd_pcm_channel_info+0x73/0x7c
[37422.640525] [<ffffffff814001e9>] snd_pcm_common_ioctl1+0x326/0xb01
[37422.640527] [<ffffffff81034306>] ? get_parent_ip+0x11/0x42
[37422.640531] [<ffffffff8105be6c>] ? __srcu_read_unlock+0x3b/0x59
[37422.640533] [<ffffffff81400bce>] snd_pcm_capture_ioctl1+0x20a/0x227
[37422.640537] [<ffffffff811e599c>] ? file_has_perm+0x90/0x9e
[37422.640540] [<ffffffff81400c15>] snd_pcm_capture_ioctl+0x2a/0x2e
[37422.640543] [<ffffffff810f2c69>] do_vfs_ioctl+0x404/0x453
[37422.640546] [<ffffffff810f2d09>] sys_ioctl+0x51/0x74
[37422.640549] [<ffffffff81002aab>] system_call_fastpath+0x16/0x1b
[37422.640552] ---[ end trace 0cd919cd68118082 ]---
We already have all the right values in place, we simply have to inform
the upper layers about this restriction.
Note that snd_hdspm_hw_rule_rate_out_channels and
snd_hdspm_hw_rule_rate_in_channels must not be called on AES32, because
the channel count is always 16, no matter of the samplerate in use.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only RayDAT and AIO provide sane buffer pointers that can be used with
HDSPM_BufferPositionMask, on all other cards, this would result in a
wrong HW pointer leading to xruns and these messages:
[260808.916788] BUG: pcmC0D0p:0, pos = 2976, buffer size = 1024, period size = 512
[260808.961124] BUG: pcmC0D0c:0, pos = 4944, buffer size = 1024, period size = 512
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a USB audio device is disconnected, snd_usb_audio_disconnect()
kills all audio URBs. At the same time, the application, after being
notified of the disconnection, might close the device, in which case
ALSA calls the .hw_free callback, which should free the URBs too.
Commit de1b8b93a0 "[ALSA] Fix hang-up at disconnection of usb-audio"
prevented snd_usb_hw_free() from freeing the URBs to avoid a hang that
resulted from this race, but this introduced another race because the
URB callbacks could now be executed after snd_usb_hw_free() has
returned, and try to access already freed data.
Fix the first race by introducing a mutex to serialize the disconnect
callback and all PCM callbacks that manage URBs (hw_free and hw_params).
Reported-and-tested-by: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
Cc: <stable@kernel.org>
[CL: also serialize hw_params callback]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default WM8958 jack detection handler implements a full set of buttons
and also support for video detection. Support for multi-button jacks is
fairly system specific and will usually require some tuning for headsets
so simplify the implementation to only report a simple short to ground
button, leaving multi-button headsets to be handled by system specific
code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8958 has a different microphone bias architecture to WM8994 so needs
different configuration to WM8994. Support this in platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow direct routing of the WM8958 microphone detection signal to a GPIO
to be used, saving the need to demux the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
As bias level changes can be quite time consuming and the bias changes
for multiple devices aren't strongly tied to each other (if anything it
can be advantageous to bring different devices up together) we can improve
the state transition time for multi-component systems by running the bias
level changes for all the devices in parallel. This is very simple to
achieve using the kernel async functionality so use that to schedule the
work.
This should have no practical effect for the overwhelming majority of
systems which have a single DAPM context - we'll bounce into another
thread to do the bias level change but otherwise everything will happen
in exactly the same order as it did before.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We can get the card from the DAPM context so don't bother passing it as
an argument.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The microphone detection functionality requires a clock to work. In any
non-detection case where the MICBIAS is enabled CLK_SYS will be needed
anyway so there is no negative impact on power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Ensure supplies are maintained for force enabled widgets
ASoC: WM8994: Improve playback robustness
ASoC: WM8994: Improve robustness in some use cases
ASoC: WM8903: Fix mic detection enable logic
ASoC: WM8903: Fix mic detection register definitions
ASoC: CX20442: fix wrong reg_cache_default content
ASoC: Sync initial widget state with hardware
This typo caused some microphone inputs not to be correctly
initialized on VIA codecs.
Reported-By: Mark Goldstein <goldstein.mark@gmail.com>
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Si4713 FM transmitter on Nokia RX-51/N900 is connected to same Line out
signals of TLV320AIC34 than TPA6130 headphone amplifier.
This patch adds route to transmitter and "FM Transmitter" control to keep
route active when needed.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch changes dependency of ARCH_EXYNOS4 from ARCH_S5PV310
according to the change of ARCH name, EXYNOS4.
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: HDA: Do not announce false surround in Conexant auto
ALSA: HDA: Conexant auto: Handle multiple connections to ADC node
ALSA: HDA: Add position_fix quirk for an Asus device
ALSA: caiaq - Fix possible string-buffer overflow
ALSA: au88x0 - Modify pointer callback to give accurate playback position
Add " Playback Volume" to 10 bands Equalizer Controls of au88x0 so that
alsa-lib won't regard them as "Capture Volume".
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this patch, one line-out and one speaker and
Conexant's auto parser would announce (non-working) surround
capabilities.
BugLink: http://bugs.launchpad.net/bugs/721126
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conexant 20641 has several inputs to its ADC node, with one selector
and individual amps for all inputs. This patch adds support in the
Conexant auto parser to handle that case.
It also means that the pin node's volume is being renamed to "Boost"
to avoid name clash with the new volume controls on the ADC node.
BugLink: http://bugs.launchpad.net/bugs/719524
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make newly created AC97 emulation of azt3328 known to the AC97 layer
side.
- relocate common functions to the top (due to definition after use)
- rename control names
- adjust 3D settings to the card's custom layout of this register
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make use of the very flexible ALSA ac97 layer (hooks for custom I/O!)
on this weird AC97 copycat hardware,
via semi-extended I/O translation/emulation.
Some 5kB binary/loaded size saved (well... additional huge AC97 module
penalty not factored in, of course ;-P).
Given that the driver previously had 20kB that's not bad,
but the much more important thing is to have AC97 layer stress-tested
with a thoroughly weird AC97 copycat (or, simply put, if it were not for
this AC97 test aspect, this effort would merely have been a nut job ;).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The microphone detection functionality requires a clock to work. In any
non-detection case where the MICBIAS is enabled CLK_SYS will be needed
anyway so there is no negative impact on power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some systems wish to use jacks as wake sources. Provide a wake flag in the
GPIO configuration which causes the driver to enable the IRQ as a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The only thing that should ever be calling this is soc-core and that is
built as part of the same module so doesn't need the export.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use AC97 macros (sometimes already existing, or newly added)
instead of error-prone repetition of open-coded values.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pulseaudio doesnt work with current driver and it was root caused to absense of
hw_params function and malloc_pages in it.
This patch adds this and allows pa to work fine with these drivers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch removes the old method of soc-audio device creation in mfld machine
and makes use of new soc_register_card API to register the card
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The tlv scale is defined as (min, step, mute). The mute is not supported here so
put the value to 0
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch makes the DMIC dynamically connect to TX Mux, earlier code had
erroneously made this as static path
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch makes the codec playback rails (headset and speaker) depend on
actual pins they control. This enables better power management of the codec
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is more usefull to report headset instead of video out cable in response
to jack insertion as this is more usual use-case and because now the headset
feature is supported. Automatic accessory detection is not possible at the
moment so most sensible static accessory type have to be used.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for headset microphone in Nokia RX-51/N900. The mic
signal from audio jack is routed to codec A LINE1L via two switches and the
mic bias is coming from codec B part.
First switch is the tv-out switch that is already supported and the second
switch selects between voltage detection circuit and codecs. As there is
no use for voltage detection at the moment the second switch is connected
statically to codecs in rx51_soc_init.
Headset can be active when control "Jack Function" is set to "Headset".
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Just slight cleanup to be sync with upcoming change.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The bug reporter claims that position_fix=1 is needed for his
microphone to work. The controller PCI vendor-id is [1002:4383] (rev 40).
Reported-by: Kjell L.
BugLink: http://bugs.launchpad.net/bugs/718402
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use strlcpy() to assure not to overflow the string array sizes by
too long USB device name string.
Reported-by: Rafa <rafa@mwrinfosecurity.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The number of cases has increased so use switch-case rather than
if-statements.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The MK2 generation of Native Instruments' sound cards are in fact
compliant to the USB audio standard of version 2 and other approved USB
standards. However, they come up as vendor-specific device when first
connected but can be told to come up with a new set of descriptors
upon their next enumeration. The interfaces announced by the new
descriptors will be handled by the kernel's class drivers. This is done
by issuing a vendor specific device request and sending the device to
reset.
There are also some vendor-specific USB requests for some mixer elements
that can't be exported in a standard compliant way. The driver now
supports them with quirks handling mechanisms.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the core code where sparse complains. In most cases, this means
just adding annotations to confirm that we indeed want to do the dirty
things we're doing.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8903 interrupts are clear on read so if the WM8903 detection is
enabled from platform data when the IRQ is in use (rather than using a
direct signal from a GPIO) status may be lost during startup. Help users
spot this misconfiguration by adding a WARN_ON().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
With the appropriate MODULE_ALIAS in place, the audio modules will be
automatically loaded; there is no longer a need for manual modprobes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Harmony has both an external mic (a regular mic jack) and an internal mic
(a 0.1" two-pin header on the board).
The external mic is connected to the WM8903's IN1L pin, and is supported
by the current driver.
The internal mic is connected to the WM8903's IN1R pin, and is not supported
by the current driver.
It appears that no Harmony systems were shipped with any internal mic
connected; users were expected to provide their own. This makes the
internal mic connection less interesting.
The WM8903's Mic Bias signal is used for both of these mics. For each mic,
a GPIO drives a transistor which gates whether the mic bias signal is
actively connected to that mic, or isolated from it.
The dual use of the mic bias for both mics makes a general-purpose complete
implementation of mic detection using the mic bias complex. So, for
simplicity, the internal mic is currently ignored by the driver.
This patch configures the relevant GPIOs to enable the mic bias connection
to the external mic, and disable the mic bias connection to the internal
mic. Note that in practice, this is the default state if these GPIOs aren't
configured.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Add jack definition for mic jack
* Request wm8903 to enable mic detection
* Force mic bias on, since it's required for mic detection
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a widget has been force enabled then not only do we need to keep the
widget itself enabled, we also need to keep any supplies the widget
requires enabled. The user could force all the individual widgets on but
this requires too much knowledge of device internals.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
On WM8994 revision D and earlier ensure proper playback robustness
as some rare use cases can trigger issues.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Ensure that on disabling certain registers such as AIF1DAC1L,
AIF1DAC1R etc. the AIF1CLK and AIF2CLK remain enabled. Similarly
when enabling those registers, AIF1CLK and AIF2CLK will remain
disabled.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The mic detection HW should be enabled when either mic or short detection
is required, not when only both are required.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - add quirk for Ordissimo EVE using a realtek ALC662
ALSA: hrtimer: remove superfluous tasklet invocation
ALSA: hrtimer: handle delayed timer interrupts
ALSA: HDA: Add subwoofer quirk for Acer Aspire 8942G
ALSA: hda - Don't handle empty patch files
ALSA: hda - Fix missing CA initialization for HDMI/DP
ALSA: usbaudio - Enable the E-MU 0204 USB
ALSA: hda - switch lfe with side in mixer for 4930g
ASoC: Improve WM8994 digital power sequencing
ASoC: Create an AIF1ADCDAT signal widget to match AIF2
asoc: davinci: da830/omap-l137: correct cpu_dai_name
ASoC: fill in snd_soc_pcm_runtime.card before calling snd_soc_dai_link.init()
It is safe to use sleeping gpio in snd_soc_jack_gpio_detect as it is not
called from interrupt context. This avoids WARN_ON from __gpio_get_value
if sleeping gpio is registered for jack.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modifies the mfld_machine to use the new jack apis for adding the
voltage zones for jack type detection. It also modifed TI sn95031 codec driver
to use these new apis
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This makes no real difference compared to the write sequencer sequence
that was previously used but can run without a clock being provided.
Also remove the write sequencer support code as this was the last use
of it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The write sequencer sequencer sequence takes longer than is desirable
as it brings up a full playback path which is not required at this
point. Open coding the sequence cuts the startup time by two thirds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Content of the CX20442's snd_soc_codec_driver.reg_cache_default pointed
area, introduced with my recent NULL pointer dereferece fix (commit
f019ee5feb), occured wrong after further
testing, more thorough than just booting successfully. There are two
problems with it:
1) It should read
(1 << CX20442_TELOUT) | (1 << CX20442_MIC),
not
CX20442_TELOUT | CX20442_MIC.
2) While correctly matching actual codec hardware state on boot when
fixed per 1), a few more code modifications would still be required
to reflect that state not only into register cache, but also force
them into DAPM pins state, otherwise an inconsitency occures which
may prevent further codec state changes from being applied correctly.
As a result, the phone stops ringing after reboot, until someone
picks up the handset for the first time.
Revert that reg_cache_default content to a working, previous de facto
default value of 0, in hope this change can still be accepted as an rc
cycle fix.
Created and tested against linux-2.6.38-rc4
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This netbook has a only one jack output and an internal mic.
By default, mic and jack sense aren't working. Using lenovo-101e
parameters makes both work.
The device seems based on a Sharetronic Q70, so this should fix audio for
this model too.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit bb758e9637 removed snd_hrtimer_callback() from the hardware
interrupt handler, thus moving it into a tasklet, but did not tell the
ALSA timer framework about this, so the timer handling would now be done
in the ALSA timer tasklet scheduled from another tasklet.
To fix this, add the flag to tell the ALSA timer framework that the
timer handler is already being invoked in a tasklet.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a timer interrupt was delayed too much, hrtimer_forward_now() will
forward the timer expiry more than once. When this happens, the
additional number of elapsed ALSA timer ticks must be passed to
snd_timer_interrupt() to prevent the ALSA timer from falling behind.
This mostly fixes MIDI slowdown problems on highly-loaded systems with
badly behaved interrupt handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Difference in major.minor between driver and firmware is an error now.
Release version mismatch give a warning.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Interrupt flag used for message handshake will be required for
stream interrupts, so conditionally compiled code without
HPI6205_NO_HSR_POLL defined can never be used; removing it.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create and use HPI_ERROR_DSP_COMMUNICATION _DSP_BOOTLOAD, rather than
backend-specific error codes (now returned as data with the error).
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
asihpi.c don't link playback and capture streams, there is too much
offset between them.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some error codes had duplicate meanings. Just use one.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reported samples_played from card may be inaccurate, so don't use it.
Update control names to be closer to alsa standard practice.
Also fixed some accidentally lowercased strings.
[Removed adriver.h inclusion for external module builds by tiwai]
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove many unused functions.
Update some message and cache structs.
Use pci info directly from pci_dev.
Allow control cache elements with variable size, and handle
large message/response from dsp.
hpi6000 and hpi6205: fix error path when adapter bootload fails.
hpimsgx.c get rid of code duplicated in hpicmn.c
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Log HPI messages and responses in consistent numeric format,
which can be post-processed to get strings.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the reporter, node 0x15 needs to be muted for subwoofer
to stop sounding. This pin is marked as unused by BIOS, so fix that.
BugLink: http://bugs.launchpad.net/bugs/715877
Cc: stable@kernel.org (2.6.37+)
Reported-by: Hans Peter
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an empty string is passed to patch option, the driver should
ignore it. Otherwise it gets an error by trying to load it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Explicitly cache the DC servo offsets for digital paths in the driver,
allowing them to be preserved over suspend and resume, and ensure that
we recalibrate analogue outputs paths when they are in use so that we
cover any changes in the input offset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds soc-jack support for adding voltage zones and for
detecting jack type
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC generally uses the register defaults for everything, but in some
cases the hardware will default to enabling some of the DAPM widgets
(clocks for example). Ensure that DAPM knows about the actual widget
state at initialisation by reading the enable bits after instantiating
the widgets so they don't get left enabled needlessly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8903 register map does not mute the DAC by default at startup
so we need to explicitly do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This simplfies the code and slightly reduces the startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
It causes noisy -codecs to appear in things like .codec_name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch modifies the Davinci i2s and mcasp drivers to make use of
ioremap() instead of IO_ADDRESS()
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case of any error in probe() function, clk_disable() and clk_put()
should be called if clk_enable() and clk_get() went through.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modifies the Davinci i2s and mcasp drivers
to make use of the resource_size() helper function for readability.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support to read the mic bias voltage
when a jack is inserted. It uses ADC to measure.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for registering jack interupt
and registering jack with core
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for jack detection and reporting in the codec
It however is not fully functional as it doesn't measure adc to figure
out what got inserted which will be added later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit 53d7d69d8f
ALSA: hdmi - support infoframe for DisplayPort
dropped the initialization of CA field accidentally.
This resulted in only two-channel LPCM mode on Nvidia machines.
Reference: kernel bug 28592
https://bugzilla.kernel.org/show_bug.cgi?id=28592
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
The patch c358e640a6 "ASoC: soc-cache: Add trace event for
snd_soc_cache_sync()" introduced a dereference of "codec->cache_ops"
before we had checked it for NULL.
I pulled the check forward, and then pulled everything in an indent
level.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move Chip Select control out of the CODEC code for CS4271.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
rt->rate is an unsigned char so it's never equal to -1. It's not a huge
problem because the invalid rate is caught inside the call to
usb6fire_pcm_set_rate() which returns -EINVAL. But if we fix the test
then it prints out the correct error message so that's good.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AACI TRM requires the MAINCR enable bit to be held zero for two
bitclk cycles plus three apb_pclk cycles. Use a delay of 1us to
ensure this.
Ensure that writes to MAINCR to change the addressed codec only happen
when required, and that they take effect in a similar manner to the
above, otherwise we seem to occasionally have stuck slot busy bits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Built-in sub-woofer can now be controlled by lfe slider instead of
side slider on Acer Aspire 5930g
Signed-off-by: Łukasz Wojniłowicz <lukasz.wojnilowicz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wm8753 codec supports switching between different DAI modes.
The current drivers tries to implement this by changing the DAI driver at
runtime. But to properly work this would require support from the ASoC core.
So this patch takes a different approch on how the DAI mode switching is
implemented.
The only difference, from a driver point of view, between the different DAI modes
is how to program the DAI format to the hardware. So what this patch is, it
stores the current format for each DAI in the drivers private struct and when
the DAI mode is changed the format gets simply reprogrammed according to the
new DAI mode.
Futhermore this patch restricts the changing of the DAI format to when the
codec is inactive.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: use linux/io.h to fix compile warnings
ALSA: hda - Fix memory leaks in conexant jack arrays
ASoC: CX20442: fix NULL pointer dereference
ASoC: Amstrad Delta: fix const related build error
ALSA: oxygen: fix output routing on Xonar DG
sound: silent echo'ed messages in Makefile
ASoC: Fix mask/val_mask confusion snd_soc_dapm_put_volsw()
ASoC: DaVinci: fix kernel panic due to uninitialized platform_data
ALSA: HDA: Fix microphone(s) on Lenovo Edge 13
ASoC: Fix module refcount for auxiliary devices
ALSA: HDA: cxt5066 - Use asus model for Asus U50F, select correct SPDIF output
ALSA: HDA: Add a new model "asus" for Conexant 5066/205xx
ALSA: HDA: Refactor some redundant code for Conexant 5066/205xx
On WM8994 revision D and earlier ensure optimal sequencing with
simultaneous usage of AIF1 and AIF2 by tying the signals together
so if paths through both are connected the streams are started
simultaneously.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
Due to the different routing for AIF1 and AIF2 we weren't using a
single widget to represent the ADCDAT signal. For consistency add
one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
McASP1 is used on the DA830/OMAP-L137 platform for the codec.
This is different from the DA850/OMAP-L138 platform which uses McASP0.
This is fixed by adding a new snd_soc_dai_link struct.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The .card member of the snd_soc_pcm_runtime structure pointed to by the
snd_soc_dai_link.init() argument used to be initialized before the
function being called. This has changed, probably unintentionally,
after recent refactorings. Since the function implementations are free
to make use of this pointer, move its assignment back before the
function is called to avoid NULL pointer dereferences.
Created and tested on Amstrad Delta againts linux-2.6.38-rc2
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some codecs with large register maps, it was not possible to dump
all registers via the codec_reg file but only up to PAGE_SIZE bytes.
This patch fixes this problem.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For helping to reduce Greert's regression list...
src/sound/drivers/mtpav.c: error: implicit declaration of function 'inb'
src/sound/drivers/mtpav.c: error: implicit declaration of function 'outb'
...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Conexant codec driver adds the jack arrays in init callback which
may be called also in each PM resume. This results in the addition of
new jack element at each time.
The fix is to check whether the requested jack is already present in
the array.
Reference: Novell bug 668929
https://bugzilla.novell.com/show_bug.cgi?id=668929
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the format of the codec_reg file more easily parsable. Remove
the header field which gives the codec name. These changes are important
when it comes to extend the debugfs codec_reg file to dump more than
PAGE_SIZE bytes to make it easier to calculate offsets within the
file.
We still need to handle the case when the snd_soc_read() call fails
and <no data: %d> is outputted.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The CX20442 codec driver never provided the snd_soc_codec_driver's
.reg_cache_default member. With the latest ASoC framework changes, it
seems to be referred unconditionally, resulting in a NULL pointer
dereference if missing. Provide it.
Created and tested on Amstrad Delta against linux-2.6.38-rc2
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Amstrad Delta ASoC driver used to override the digital_mute()
callback, expected to be not provided by the on-board CX20442 CODEC
driver, with its own implementation. While this is still posssible when
substituting the whole empty snd_soc_dai_driver.ops member (the CX20442
case), replacing snd_soc_dai_ops.digital_mute only is no longer correct
after the snd_soc_dai_driver.ops member has been constified, and results
in build error.
Drop this actually not used code path in hope the CX20442 driver never
provides its own snd_soc_dai_ops structure.
Created and tested against linux-2.6.38-rc2
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
gpio_set_value* should accept logic values not just 0 or 1. The WM8903 GPIO
driver has been fixed to work this way, so remove the redundant !!
previously required when it didn't accept values >1.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Earphone in Nokia RX-51/N900 is connected to left HP output of B part of the
TLV320AIC34 dual codec. In RX-51 the codec A is used as a traditional codec
and the codec B as an auxiliary device.
Audio from codec A goes via the codec B to earphone:
MONO_LOUT of A -> LINE2R of B (B interconnects) -> HPLOUT of B -> Earphone.
Take earphone into use by utilizing the recent ASoC auxiliary and
cross-device support.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This driver does not use any of the functionality provided by the scoop
hardware. Remove the unneeded header.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead, have the machine driver provide storage for the utility data
somehow.
For Harmony in particular, store this within struct tegra_harmony, itself
referenced by snd_soc_card's drvdata.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Indent with TABs not spaces.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DAPM widget definitions for the internal speaker paths. Currently, this
path is always enabled while playback is active.
Add code to control the speaker amplifier GPIO.
The GPIO is requested during _init, since that's the first time it is
guaranteed that the WM8903 module is loaded, probed, and hence has exported
its GPIO chip.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously, snd-soc-tegra-harmony internally instantiated a platform device
object whenever the module was loaded. Instead, switch to a more typical model
where arch/arm/mach-tegra defines a platform device, and snd-soc-tegra-harmony
acts as a driver for such a platform device.
Define a new struct tegra_harmony to store driver data in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All ASoC cards need snd_soc_initialize_card_lists called. Previously, it was
only called for cards backed by a "soc-audio" platform device, via
soc_probe(). However, it's also needed for cards backed by other platform
devices, and registered directly via snd_soc_register_card().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the support for capture path in sn95031 codec.
This codec supports upto 6DMICs, 2 AMICs and Linein. The linein and AMICs
are connected through a MUX to ADC. The TX paths can be assigned to any of the
ADCs or DMICs.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This card uses separate I2S outputs for the front speakers and
headphones, and reverses the order of the three speaker outputs.
To work around this, add a model-specific callback to adjust the
controller's playback routing.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: HDA: Fix automute on Thinkpad L412/L512
ALSA: HDA: Fix dmesg output of HDMI supported bits
ALSA: fix invalid hardware.h include in ac97c for AVR32 architecture
ASoC: correct link specifications for corgi, poodle and spitz
ASoC: Samsung: Fix outdated cpu_dai_name for s3c24xx i2s
ASoC: Fix codec device id format used by some dai_links
ALSA: azt3328 - fix broken AZF_FMT_XLATE macro
ALSA: Xonar, CS43xx: Don't overrun static array
ASoC: Handle low measured DC offsets for wm_hubs devices
ASoC: da8xx/omap-l1xx: match codec_name with i2c ids
ASoC: WM8994: fix wrong value in tristate function
ASoC: WM8995: Fix incorrect use of snd_soc_update_bits()
snd_soc_dapm_put_volsw() has variables for both the unshifted and
shifted mask for updates commit 97404f (ASoC: Do DAPM control updates in
the middle of DAPM sequences) got confused between the two of these.
Since there's no need to keep a copy of the unshifted mask fix this and
simplify the code by using only one mask variable.
[Completely rewrote the changelog to describe the issue -- broonie.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit f6c2ed5 "ASoC: Fix the device references to codec and platform drivers"
moved codec and platform driver refcount increments from soc_bind_dai_link
to more appropriate places.
Adjust a little them so that refcounts are incremented before executing the
driver probe functions.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Harsha Priya <priya.harsha@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes the Kernel panic issue on accessing davinci_vc in
cq93vc_probe function. struct davinci_vc is part of platform device's
private driver data(codec->dev->p->driver_data) and this is populated
by DaVinci Voice Codec MFD driver.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
BugLink: http://bugs.launchpad.net/bugs/708521
This Edge 13 model has an internal mic at 0x1a and should
therefore use the asus quirk.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
Audio jack in Nokia RX-51/N900 is driven by TPA6130 headphone amplifier.
This patch adds support for it and stereo output can be active when
"Jack Function" == "TV-OUT" || "Headphone".
As the TPA6130 can output very high volume levels the output is limited
with snd_soc_limit_volume. Limiting value is found from Maemo kernel sources.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allows drivers to distinguish which subsequence is being notified when
they get called back.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Could just as well live in sysfs but sysfs doesn't have the simple
value export helpers debugfs does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow hookup of cards registered directly with the core to the PM
operations by exporting the device power management operations to
modules, also exporting the default PM operations since it is
expected that most cards will end up using exactly the same setup.
Note that the callbacks require that the driver data for the card be
the snd_soc_card.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In order to support cards instantiated without using soc-audio remove
the use of the platform device in the card probe() and remove() ops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The platform device for the card is tied closely to the soc-audio
implementation which we're currently trying to remove in favour of
allowing cards to have their own devices. Begin removing it by
replacing it with the card in the suspend and resume callbacks we
give to cards, also taking the opportunity to remove the legacy
suspend types which are currently hard coded anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
As requested by Takashi and Jaroslav, these arrays should not be in the
header file.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Inform users about the newly added support for RayDAT and AIO.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Incorporate changes by Florian Faber into hdspm.c. Code taken from
http://wiki.linuxproaudio.org/index.php/Driver:hdspe
Heavily reworked to mostly comply with the coding standard (whitespace
fixes, line width, C++ style comments)
The code was tested and confirmed to be working on RME RayDAT.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Richard Samson