- correct spelling/whitespace in ftdi_sio.h and ftdi_sio_ids.h
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).
Compile-tested, based on latest mainline git.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Detect the UART on interface1 and blacklist interface0 (as that is the
JTAG port).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices from the OpenDCC project are missing in the list
of the FTDI PIDs. These PIDs are listed at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
(Sorry for the german only page.)
This patch adds the three missing devices.
Signed-off-by: Rainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'd like to present my small patch enabling to use Hameg HM8143 programmable
power supply with linux.
Signed-off-by: Pawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached patch adds USB vendor and product IDs for Bayer's USB to serial
converter cable used by Bayer blood glucose meters. It seems to be a
FT232RL based device and works without any problem with ftdi_sio driver
when this patch is applied. See: http://winglucofacts.com/cables/
Signed-off-by: Marko Hänninen <bugitus@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds support for the GN Otometrics Aurical USB Audiometer
(FT232BM-based).
A new VID and a new PID is added.
Signed-off-by: Ville Sundberg <vsundber@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds USB ID for Turtelizer, an FT2232L-based JTAG/RS-232 adapter.
Signed-off-by: Krzysztof Ha³asa <khc@pm.waw.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It enhances the driver for FTDI-based USB serial adapters to recognize and
support Northern Digital Inc (NDI) measurement equipment. NDI has been
providing this patch for various kernel flavors for several years and we would
like to see these changes built in to the driver so that our equipement works
without the need for customers to patch the kernel themselves.
The patch makes small modifications to 2 files: ./drivers/usb/serial/ftdi_sio.c
and ./drivers/usb/serial/ftdi_sio.h. It accomplishes 3 things:
1. Define the VID and PIDs to allow the driver to recognize the NDI devices.
2. Map the 19200 baud rate setting to our higher baud rate of 1.2Mb
We would have chosen to map 38400 to the higher rate, similar to what
several other vendors have done, but some of our legacy customers actually
use 38400, therefore we remap 19200 to the higher rate.
3. We set the default transmit latency in the FTDI chip to 1ms for our devices.
Our devices are typically polled at 60Hz and the default ftdi latency
seriously affects turn-around time and results in missed data frames. We
have created a modprobe option that allows this setting to be increased.
This has proven necessary particularly in some virtualized environments.
Signed-off-by: Martin P. Geleynse <mgeleyns@ndigital.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems an USB device with vendor id 0403 and product code FB80 has an
FTDI serial io chip as well: http://ftdichip.com/Drivers/D2XX.htm
This device in fact is a true random generantor by comsci:
http://comscire.com/Products/R2000KU/
So the following patch should add support for this device if I am
correct. Not tested as I do not own this device (I would like support in
the kernel so that my entropybroker application (which distributes
entrop data (random values) between servers and clients)).
From: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The product ID's for the following devices have been added:
- LOAD-n-GO
- ICD-U64
- PRIME-8
Signed-off-by: Jan Capek <jan@ccsinfo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for FTDI's USB 2.0 hi-speed devices - FT2232H (2
interfaces) and FT4232H (4 interfaces), including a new baud rate
calculation for these devices which can now achieve up to 12Mbaud by
turning off a divide by 2.5 in the baud rate generator of the chips. In
order to achieve baud rates of <1200 baud, the divide by 2.5 must be
active. The default product ID of the FT2232H is 0x6010 (same as the
FT2232C IC). The default PID of the FT4232H is 0x6011.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to have added new device to usbserial/ftdi_sio driver.
These ids used USB track device (http://www.l-and-b.dk/access_alt.html).
They use differend device IDs, but it works as standard usb-serial
conventer.
From: Daniel Suchy <danny@danysek.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the NDI Polaris system *http://www.ndigital.com/).
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson <eu@mhayk.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: Robie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Someone on rmweb reminded me this had been overlooked from ages ago..
Add the identifiers for the Sprog II USB. This is a DCC control interface
using the FTDI-SIO hardware: http://www.sprog-dcc.co.uk/. People have been
using it with insmod options for ages, this just puts it into the driver
data.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Oceanic PID to ftdi_sio driver
Oceanic dive computers (such as the VT3 --
http://www.oceanicworldwide.com/p_computers_vt3.html) all use an onboard
FTDI serial converter, with the FTDI vid and a PID of 0xf460. The
attached patch adds that pid to ftdi_sio; driver connects to my VT3
after that.
Signed-off-by: Vladimir Vukicevic <vladimir@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.
Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: Lex V. Ross <lross@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Patch adds support for Luminance Stellaris Evaluation/Development
Kits (FTDI 2232C based).
The PIDs were missing.
Successfully tested with a Stellaris LM3S8962 Evaluation kit.
Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB product id registration for the ELV HS485 USB adapter (www.elv.de) to
their home automation bus system. Applies to 2.6.26.
Signed-off-by: Andre Schenk <andre@melior.s.bawue.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.
The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.
(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0403 ProdID=ed22 Rev= 5.00
S: Manufacturer=FTDI
S: Product=MixW RigExpert Tiny
S: SerialNumber=00000000
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
)
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.
A small number of units have been shipped early 2008
with a faulty USB Descriptor. Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: R. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reverts 57833ea6b9
("usb-serial: pl2303: add support for RATOC REX-USB60F") and adds
support for the device to ftdi_sio driver.
Cc: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Cc: stable <stable@kernel.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch that adds support for the propox jtagcable II dongle
(http://www.propox.com/products/t_117.html): their PID was missing,
therefore we were not able to have the device recognized though it uses
a standard FTDI chip.
Signed-off-by: Mirko Bordignon <mirko.bordignon@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Workaround for the FT232RL-based, Matrix Orbital VK204-25-USB serial port
added to the ftdi_sio driver.
The device has an invalid endpoint descriptor, which must be modified
before it can be used.
Signed-off-by: Kevin Vance <kvance@kvance.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] ftdi_sio: add support for more FTDI based JTAG adaptors
There are more devices similar to the Olimex JTAG adaptor, in that the first
port of the FT2232C is used for JTAG, and only the second port is available as
UART.
I have thus renamed ftdi_olimex_{probe,quirk} to ftdi_jtag_{probe,quirk} and
added vendor/product ID's for the OpenMoko Neo1973 Debug Board as well as the
OOCDlink device.
I've also updated the KERN_INFO message sent to userspace to remove the word
'olimex' and an extra '\n' that was causing an empty line in dmesg.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for the Elster Unicom III Optical Probe.
The device ID has already been added to the usb.ids file.
Cc: stable <stable@kernel.org>
Signed-off-by: Ed Beroset <beroset@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
little patches only to add vendor/device id of ATK_16IC CCD cam for
astronomy.
From: Franco Lanza <nextime@nexlab.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I work with a group of people on a free home automation tool called
FHEM. Some of the users own more than one USB-serial device by ELV. The
ftdi_sio driver has most of the ELV devices disabled by default and
needs to be re-enabled every time you get a new kernel. Additionally a
new device (EM 1010 PC - enegry monitor) is missing in the list.
Currently our users have to follow the instructions we provide at
http://www.koeniglich.de/fhem/linux.html ... However, to some users it
is too complicated to compile their own kernel module.
We are aware that you can specify one additional device using the
vendor/product option of the module. But lot's of users own more than
one device.
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Stark <peter.stark@t-online.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
I have added to a new product based on the FTDI 232R USB/Serial
transceiver, which is commercialized by The Mobility Lab. Here is a
trivial patch enclosed, against 2.6.22.6 kernel.
Signed-off-by: Pierre Castella <pp.castella@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached (mostly trivial) patches adds support for the Evolution
Scorpion Robots.
Evolution Robotics supplies a patch against 2.6.8 with their
software. My patch is based on their work, so I don't know if I can
sign it off, or if you need some Evolution people to do this (which
might be hard).
The patch adds device ID's for some robots which is trivial.
From: Søren Hauberg <hauberg@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Søren
Reported by Grzegorz Chimosz <gchimi@gmail.com>
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the serial port on Olimex arm-usb-ocd
JTAG interface.
The device appears as two serial ports, but the first one is reserved
for the JTAG interface. The JTAG interface can be used with OpenOCD
from userspace. For more information, please see:
http://openocd.berlios.de/web/http://www.olimex.com/dev/arm-usb-ocd.html
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB product id registration for the OpenDCC (www.opendcc.de)
model railway central unit. Applies to 2.6.21.1.
Signed-off-by: Guido Scholz <guido.scholz@bayernline.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hello,
I need to use MaxStream's PKG-U modules which includes a ftdi sio chipset for
usb2serial communication, here are the patches for handling Maxstream's modules.
The VID & PID to use with the open-source driver are provided on the CD-ROM
bundled with the modules.
From: Neil Superna ARMSTRONG <superna@na-prod.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the USB ID of the ADS Tech USBX-707 USB IR blaster (that
comes with the ADS Tech PTV-305 grabber card), which has a ftdi232bm
inside hooked up to a pic.
With this it should be fairly straightforward to make at least lirc
receiving work with this device. I will submit a patch to lirc for that
as soon as I have one ready, I'm getting data with minicom with this
patch, but need to figure out some more details such as best/correct
baudrate.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman