Create an enum for DSI operation modes, use this to set the capabilities of the
device in dsi_init_display().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.
Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Remove support for non-DISPC overlays and overlay managers.
The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:
- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
omapdss driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.
Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().
A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PicoDLP is a micro projector from TI.
DLP used in OMAP4 is dpp2600 (DLP Pico Projector) The DLP requires
commands to be sent over i2c for configurations. To know more about
dpp2600 commands please visit:
https://focus.ti.com/myti/docs/extranet.tsp?sectionId=403
The picodlp module consists of a dss driver and an i2c_client.
To know more please visit:
http://www.omappedia.org/wiki/PicoDLP_projector_guide
Based on original design from Mythri P K <mythripk@ti.com>
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: squashed commits]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix kernel-doc warning about internal/private data by marking it
as "private:" so that kernel-doc will ignore it.
Warning(include/linux/regulator/consumer.h:128): No description found for parameter 'ret'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-doc warning in net/cfg80211.h:
Warning(include/net/cfg80211.h:1884): No description found for parameter 'registered'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perf-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86, perf: Check that current->mm is alive before getting user callchain
perf_event: Fix broken calc_timer_values()
perf events: Fix slow and broken cgroup context switch code
Some of the flags are OS/arch dependent we add a 9p
protocol value which maps to asm-generic/fcntl.h values in Linux
Based on the original patch from Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
netpoll: fix incorrect access to skb data in __netpoll_rx
cassini: init before use in cas_interruptN.
can: ti_hecc: Fix uninitialized spinlock in probe
can: ti_hecc: Fix unintialized variable
net: sh_eth: fix the compile error
net/phy: fix DP83865 phy interrupt handler
sendmmsg/sendmsg: fix unsafe user pointer access
ibmveth: Fix leak when recycling skb and hypervisor returns error
arp: fix rcu lockdep splat in arp_process()
bridge: fix a possible use after free
bridge: Pseudo-header required for the checksum of ICMPv6
mcast: Fix source address selection for multicast listener report
MAINTAINERS: Update GIT trees for network development
ath9k: Fix PS wrappers in ath9k_set_coverage_class
carl9170: Fix mismatch in carl9170_op_set_key mutex lock-unlock
wl12xx: add max_sched_scan_ssids value to the hw description
wl12xx: Fix validation of pm_runtime_get_sync return value
wl12xx: Remove obsolete testmode NVS push command
bcma: add uevent to the bus, to autoload drivers
ath9k_hw: Fix STA (AR9485) bringup issue due to incorrect MAC address
...
The current cgroup context switch code was incorrect leading
to bogus counts. Furthermore, as soon as there was an active
cgroup event on a CPU, the context switch cost on that CPU
would increase by a significant amount as demonstrated by a
simple ping/pong example:
$ ./pong
Both processes pinned to CPU1, running for 10s
10684.51 ctxsw/s
Now start a cgroup perf stat:
$ perf stat -e cycles,cycles -A -a -G test -C 1 -- sleep 100
$ ./pong
Both processes pinned to CPU1, running for 10s
6674.61 ctxsw/s
That's a 37% penalty.
Note that pong is not even in the monitored cgroup.
The results shown by perf stat are bogus:
$ perf stat -e cycles,cycles -A -a -G test -C 1 -- sleep 100
Performance counter stats for 'sleep 100':
CPU1 <not counted> cycles test
CPU1 16,984,189,138 cycles # 0.000 GHz
The second 'cycles' event should report a count @ CPU clock
(here 2.4GHz) as it is counting across all cgroups.
The patch below fixes the bogus accounting and bypasses any
cgroup switches in case the outgoing and incoming tasks are
in the same cgroup.
With this patch the same test now yields:
$ ./pong
Both processes pinned to CPU1, running for 10s
10775.30 ctxsw/s
Start perf stat with cgroup:
$ perf stat -e cycles,cycles -A -a -G test -C 1 -- sleep 10
Run pong outside the cgroup:
$ /pong
Both processes pinned to CPU1, running for 10s
10687.80 ctxsw/s
The penalty is now less than 2%.
And the results for perf stat are correct:
$ perf stat -e cycles,cycles -A -a -G test -C 1 -- sleep 10
Performance counter stats for 'sleep 10':
CPU1 <not counted> cycles test # 0.000 GHz
CPU1 23,933,981,448 cycles # 0.000 GHz
Now perf stat reports the correct counts for
for the non cgroup event.
If we run pong inside the cgroup, then we also get the
correct counts:
$ perf stat -e cycles,cycles -A -a -G test -C 1 -- sleep 10
Performance counter stats for 'sleep 10':
CPU1 22,297,726,205 cycles test # 0.000 GHz
CPU1 23,933,981,448 cycles # 0.000 GHz
10.001457237 seconds time elapsed
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110825135803.GA4697@quad
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
omap-serial: Allow IXON and IXOFF to be disabled.
TTY: serial, document ignoring of uart->ops->startup error
TTY: pty, fix pty counting
8250: Fix race condition in serial8250_backup_timeout().
serial/8250_pci: delete duplicate data definition
8250_pci: add support for Rosewill RC-305 4x serial port card
tty: Add "spi:" prefix for spi modalias
atmel_serial: fix atmel_default_console_device
serial: 8250_pnp: add Intermec CV60 touchscreen device
drivers/serial/ucc_uart.c: Fix compiler warning
pch_uart: Set PCIe bus number using probe parameter
serial: samsung: Fix build error
We need a callback to do some things after pwm_enable, pwm_disable
and pwm_config.
Signed-off-by: Dilan Lee <dilee@nvidia.com>
Reviewed-by: Robert Morell <rmorell@nvidia.com>
Reviewed-by: Arun Murthy <arun.murthy@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace/remove use of RIO v.1.2 registers/bits that are not
forward-compatible with newer versions of RapidIO specification.
RapidIO specification v.1.3 removed Write Port CSR, Doorbell CSR,
Mailbox CSR and Mailbox and Doorbell bits of the PEF CAR.
Use of removed (since RIO v.1.3) register bits affects users of
currently available 1.3 and 2.x compliant devices who may use not so
recent kernel versions.
Removing checks for unsupported bits makes corresponding routines
compatible with all versions of RapidIO specification. Therefore,
backporting makes stable kernel versions compliant with RIO v.1.3 and
later as well.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Chul Kim <chul.kim@idt.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Purely in-memory filesystems do not use the inode hash as the dcache
tells us if an entry already exists. As a result, they do not call
unlock_new_inode, and thus directory inodes do not get put into a
different lockdep class for i_sem.
We need the different lockdep classes, because the locking order for
i_mutex is different for directory inodes and regular inodes. Directory
inodes can do "readdir()", which takes i_mutex *before* possibly taking
mm->mmap_sem (due to a page fault while copying the directory entry to
user space).
In contrast, regular inodes can be mmap'ed, which takes mm->mmap_sem
before accessing i_mutex.
The two cases can never happen for the same inode, so no real deadlock
can occur, but without the different lockdep classes, lockdep cannot
understand that. As a result, if CONFIG_DEBUG_LOCK_ALLOC is set, this
can lead to false positives from lockdep like below:
find/645 is trying to acquire lock:
(&mm->mmap_sem){++++++}, at: [<ffffffff81109514>] might_fault+0x5c/0xac
but task is already holding lock:
(&sb->s_type->i_mutex_key#15){+.+.+.}, at: [<ffffffff81149f34>]
vfs_readdir+0x5b/0xb4
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&sb->s_type->i_mutex_key#15){+.+.+.}:
[<ffffffff8108ac26>] lock_acquire+0xbf/0x103
[<ffffffff814db822>] __mutex_lock_common+0x4c/0x361
[<ffffffff814dbc46>] mutex_lock_nested+0x40/0x45
[<ffffffff811daa87>] hugetlbfs_file_mmap+0x82/0x110
[<ffffffff81111557>] mmap_region+0x258/0x432
[<ffffffff811119dd>] do_mmap_pgoff+0x2ac/0x306
[<ffffffff81111b4f>] sys_mmap_pgoff+0x118/0x16a
[<ffffffff8100c858>] sys_mmap+0x22/0x24
[<ffffffff814e3ec2>] system_call_fastpath+0x16/0x1b
-> #0 (&mm->mmap_sem){++++++}:
[<ffffffff8108a4bc>] __lock_acquire+0xa1a/0xcf7
[<ffffffff8108ac26>] lock_acquire+0xbf/0x103
[<ffffffff81109541>] might_fault+0x89/0xac
[<ffffffff81149cff>] filldir+0x6f/0xc7
[<ffffffff811586ea>] dcache_readdir+0x67/0x205
[<ffffffff81149f54>] vfs_readdir+0x7b/0xb4
[<ffffffff8114a073>] sys_getdents+0x7e/0xd1
[<ffffffff814e3ec2>] system_call_fastpath+0x16/0x1b
This patch moves the directory vs file lockdep annotation into a helper
function that can be called by in-memory filesystems and has hugetlbfs
call it.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* '3.1-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (21 commits)
target: Convert acl_node_lock to be IRQ-disabling
target: Make locking in transport_deregister_session() IRQ safe
tcm_fc: init/exit functions should not be protected by "#ifdef MODULE"
target: Print subpage too for unhandled MODE SENSE pages
iscsi-target: Fix iscsit_allocate_se_cmd_for_tmr failure path bugs
iscsi-target: Implement iSCSI target IPv6 address printing.
target: Fix task SGL chaining breakage with transport_allocate_data_tasks
target: Fix task count > 1 handling breakage and use max_sector page alignment
target: Add missing DATA_SG_IO transport_cmd_get_valid_sectors check
target: Fix SYNCHRONIZE_CACHE zero LBA + range breakage
target: Remove duplicate task completions in transport_emulate_control_cdb
target: Fix WRITE_SAME usage with transport_get_size
target: Add WRITE_SAME (10) parsing and refactor passthrough checks
target: Fix write payload exception handling with ->new_cmd_map
iscsi-target: forever loop bug in iscsit_attach_ooo_cmdsn()
iscsi-target: remove duplicate return
target: Convert target_core_rd.c to use use BUG_ON
iscsi-target: Fix leak on failure in iscsi_copy_param_list()
target: Use ERR_CAST inlined function
target: Make standard INQUIRY return 'not connected' for tpg_virt_lun0
...
I ran into a couple of programs which broke with the new Linux 3.0
version. Some of those were binary only. I tried to use LD_PRELOAD to
work around it, but it was quite difficult and in one case impossible
because of a mix of 32bit and 64bit executables.
For example, all kind of management software from HP doesnt work, unless
we pretend to run a 2.6 kernel.
$ uname -a
Linux svivoipvnx001 3.0.0-08107-g97cd98f #1062 SMP Fri Aug 12 18:11:45 CEST 2011 i686 i686 i386 GNU/Linux
$ hpacucli ctrl all show
Error: No controllers detected.
$ rpm -qf /usr/sbin/hpacucli
hpacucli-8.75-12.0
Another notable case is that Python now reports "linux3" from
sys.platform(); which in turn can break things that were checking
sys.platform() == "linux2":
https://bugzilla.mozilla.org/show_bug.cgi?id=664564
It seems pretty clear to me though it's a bug in the apps that are using
'==' instead of .startswith(), but this allows us to unbreak broken
programs.
This patch adds a UNAME26 personality that makes the kernel report a
2.6.40+x version number instead. The x is the x in 3.x.
I know this is somewhat ugly, but I didn't find a better workaround, and
compatibility to existing programs is important.
Some programs also read /proc/sys/kernel/osrelease. This can be worked
around in user space with mount --bind (and a mount namespace)
To use:
wget ftp://ftp.kernel.org/pub/linux/kernel/people/ak/uname26/uname26.c
gcc -o uname26 uname26.c
./uname26 program
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: check size of FUSE_NOTIFY_INVAL_ENTRY message
fuse: mark pages accessed when written to
fuse: delete dead .write_begin and .write_end aops
fuse: fix flock
fuse: fix non-ANSI void function notation
tty_operations->remove is normally called like:
queue_release_one_tty
->tty_shutdown
->tty_driver_remove_tty
->tty_operations->remove
However tty_shutdown() is called from queue_release_one_tty() only if
tty_operations->shutdown is NULL. But for pty, it is not.
pty_unix98_shutdown() is used there as ->shutdown.
So tty_operations->remove of pty (i.e. pty_unix98_remove()) is never
called. This results in invalid pty_count. I.e. what can be seen in
/proc/sys/kernel/pty/nr.
I see this was already reported at:
https://lkml.org/lkml/2009/11/5/370
But it was not fixed since then.
This patch is kind of a hackish way. The problem lies in ->install. We
allocate there another tty (so-called tty->link). So ->install is
called once, but ->remove twice, for both tty and tty->link. The fix
here is to count both tty and tty->link and divide the count by 2 for
user.
And to have ->remove called, let's make tty_driver_remove_tty() global
and call that from pty_unix98_shutdown() (tty_operations->shutdown).
While at it, let's document that when ->shutdown is defined,
tty_shutdown() is not called.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.
Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes target_emulate_inquiry_std() to set the 'not connected'
(0x35) bit in standard INQUIRY response data when we are processing a
request to a virtual LUN=0 mapping from struct se_device *g_lun0_dev that
have been setup for us in transport_lookup_cmd_lun().
This addresses an issue where qla2xxx FC clients need to be able
to create demo-mode I_T FC Nexuses by default, but should not be
exposing the default set of TPG LUNs to all FC clients. This includes
adding an new optional target_core_fabric_ops->tpg_check_demo_mode_login_only()
caller to allow demo_mode nexuses to skip the old default of bulding
a demo-mode MappedLUNs list via core_tpg_add_node_to_devs().
(roland: Add missing tpg_check_demo_mode_login_only check in core_dev_add_lun)
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
* 'for-linus' of git://git.kernel.dk/linux-block: (23 commits)
Revert "cfq: Remove special treatment for metadata rqs."
block: fix flush machinery for stacking drivers with differring flush flags
block: improve rq_affinity placement
blktrace: add FLUSH/FUA support
Move some REQ flags to the common bio/request area
allow blk_flush_policy to return REQ_FSEQ_DATA independent of *FLUSH
xen/blkback: Make description more obvious.
cfq-iosched: Add documentation about idling
block: Make rq_affinity = 1 work as expected
block: swim3: fix unterminated of_device_id table
block/genhd.c: remove useless cast in diskstats_show()
drivers/cdrom/cdrom.c: relax check on dvd manufacturer value
drivers/block/drbd/drbd_nl.c: use bitmap_parse instead of __bitmap_parse
bsg-lib: add module.h include
cfq-iosched: Reduce linked group count upon group destruction
blk-throttle: correctly determine sync bio
loop: fix deadlock when sysfs and LOOP_CLR_FD race against each other
loop: add BLK_DEV_LOOP_MIN_COUNT=%i to allow distros 0 pre-allocated loop devices
loop: add management interface for on-demand device allocation
loop: replace linked list of allocated devices with an idr index
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: OF: Don't crash when bridge parent is NULL.
PCI: export pcie_bus_configure_settings symbol
PCI: code and comments cleanup
PCI: make cardbus-bridge resources optional
PCI: make SRIOV resources optional
PCI : ability to relocate assigned pci-resources
PCI: honor child buses add_size in hot plug configuration
PCI: Set PCI-E Max Payload Size on fabric
Revert the pass-good area introduced in ffd1f609ab ("writeback:
introduce max-pause and pass-good dirty limits") and make the max-pause
area smaller and safe.
This fixes ~30% performance regression in the ext3 data=writeback
fio_mmap_randwrite_64k/fio_mmap_randrw_64k test cases, where there are
12 JBOD disks, on each disk runs 8 concurrent tasks doing reads+writes.
Using deadline scheduler also has a regression, but not that big as CFQ,
so this suggests we have some write starvation.
The test logs show that
- the disks are sometimes under utilized
- global dirty pages sometimes rush high to the pass-good area for
several hundred seconds, while in the mean time some bdi dirty pages
drop to very low value (bdi_dirty << bdi_thresh). Then suddenly the
global dirty pages dropped under global dirty threshold and bdi_dirty
rush very high (for example, 2 times higher than bdi_thresh). During
which time balance_dirty_pages() is not called at all.
So the problems are
1) The random writes progress so slow that they break the assumption of
the max-pause logic that "8 pages per 200ms is typically more than
enough to curb heavy dirtiers".
2) The max-pause logic ignored task_bdi_thresh and thus opens the possibility
for some bdi's to over dirty pages, leading to (bdi_dirty >> bdi_thresh)
and then (bdi_thresh >> bdi_dirty) for others.
3) The higher max-pause/pass-good thresholds somehow leads to the bad
swing of dirty pages.
The fix is to allow the task to slightly dirty over task_bdi_thresh, but
no way to exceed bdi_dirty and/or global dirty_thresh.
Tests show that it fixed the JBOD regression completely (both behavior
and performance), while still being able to cut down large pause times
in balance_dirty_pages() for single-disk cases.
Reported-by: Li Shaohua <shaohua.li@intel.com>
Tested-by: Li Shaohua <shaohua.li@intel.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
This allows the cast in lowmem_page_address (introduced as a warning
fixup to 33dd4e0ec9 "mm: make some struct page's const") to be
removed.
Propagate const'ness to page_to_section() as well since it is required
by __page_to_pfn.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Followup to 33dd4e0ec9 "mm: make some struct page's const" which missed the
HASHED_PAGE_VIRTUAL case.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rtc: Limit RTC PIE frequency
rtc: Fix hrtimer deadlock
rtc: Handle errors correctly in rtc_irq_set_state()
Fixup trivial conflicts in drivers/rtc/interface.c due to slightly
trivially versions of the same patch coming in two different ways.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq: Track the owner of irq descriptor
irq: Always set IRQF_ONESHOT if no primary handler is specified
genirq: Fix wrong bit operation
Commit ae1b153962, block: reimplement
FLUSH/FUA to support merge, introduced a performance regression when
running any sort of fsyncing workload using dm-multipath and certain
storage (in our case, an HP EVA). The test I ran was fs_mark, and it
dropped from ~800 files/sec on ext4 to ~100 files/sec. It turns out
that dm-multipath always advertised flush+fua support, and passed
commands on down the stack, where those flags used to get stripped off.
The above commit changed that behavior:
static inline struct request *__elv_next_request(struct request_queue *q)
{
struct request *rq;
while (1) {
- while (!list_empty(&q->queue_head)) {
+ if (!list_empty(&q->queue_head)) {
rq = list_entry_rq(q->queue_head.next);
- if (!(rq->cmd_flags & (REQ_FLUSH | REQ_FUA)) ||
- (rq->cmd_flags & REQ_FLUSH_SEQ))
- return rq;
- rq = blk_do_flush(q, rq);
- if (rq)
- return rq;
+ return rq;
}
Note that previously, a command would come in here, have
REQ_FLUSH|REQ_FUA set, and then get handed off to blk_do_flush:
struct request *blk_do_flush(struct request_queue *q, struct request *rq)
{
unsigned int fflags = q->flush_flags; /* may change, cache it */
bool has_flush = fflags & REQ_FLUSH, has_fua = fflags & REQ_FUA;
bool do_preflush = has_flush && (rq->cmd_flags & REQ_FLUSH);
bool do_postflush = has_flush && !has_fua && (rq->cmd_flags &
REQ_FUA);
unsigned skip = 0;
...
if (blk_rq_sectors(rq) && !do_preflush && !do_postflush) {
rq->cmd_flags &= ~REQ_FLUSH;
if (!has_fua)
rq->cmd_flags &= ~REQ_FUA;
return rq;
}
So, the flush machinery was bypassed in such cases (q->flush_flags == 0
&& rq->cmd_flags & (REQ_FLUSH|REQ_FUA)).
Now, however, we don't get into the flush machinery at all. Instead,
__elv_next_request just hands a request with flush and fua bits set to
the scsi_request_fn, even if the underlying request_queue does not
support flush or fua.
The agreed upon approach is to fix the flush machinery to allow
stacking. While this isn't used in practice (since there is only one
request-based dm target, and that target will now reflect the flush
flags of the underlying device), it does future-proof the solution, and
make it function as designed.
In order to make this work, I had to add a field to the struct request,
inside the flush structure (to store the original req->end_io). Shaohua
had suggested overloading the union with rb_node and completion_data,
but the completion data is used by device mapper and can also be used by
other drivers. So, I didn't see a way around the additional field.
I tested this patch on an HP EVA with both ext4 and xfs, and it recovers
the lost performance. Comments and other testers, as always, are
appreciated.
Cheers,
Jeff
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Function genpd_queue_power_off_work() is not defined for
CONFIG_PM_RUNTIME, so pm_genpd_poweroff_unused() causes a build
error to happen in that case. Fix the problem by making
pm_genpd_poweroff_unused() depend on CONFIG_PM_RUNTIME too.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
e1000e: increase driver version number
e1000e: alternate MAC address update
e1000e: do not disable receiver on 82574/82583
e1000e: alternate MAC address does not work on device id 0x1060
PCnet: Fix section mismatch
bnx2x: disable dcb on 578xx since not supported yet
bnx2x: properly clean indirect addresses
bnx2x: prevent race between undi_unload and load flows
bnx2x: fix select_queue when FCoE is disabled
bnx2x: init FCOE FP only once
ipv4: some rt_iif -> rt_route_iif conversions
net/bridge/netfilter/ebtables.c: use available error handling code
net/netlabel/netlabel_kapi.c: add missing cleanup code
net/irda: sh_sir: tidyup compile warning
net/irda: sh_sir: add missing header
net/irda: sh_irda: add missing header
slcan: ldisc generated skbs are received in softirq context
scm: Capture the full credentials of the scm sender
tcp: initialize variable ecn_ok in syncookies path
drivers/net/wireless/wl1251: add missing kfree
...
My gmail account got disabled and I'm not going to reopen it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch http://lkml.org/lkml/2003/7/13/226 introduced an RLIMIT_NPROC
check in set_user() to check for NPROC exceeding via setuid() and
similar functions.
Before the check there was a possibility to greatly exceed the allowed
number of processes by an unprivileged user if the program relied on
rlimit only. But the check created new security threat: many poorly
written programs simply don't check setuid() return code and believe it
cannot fail if executed with root privileges. So, the check is removed
in this patch because of too often privilege escalations related to
buggy programs.
The NPROC can still be enforced in the common code flow of daemons
spawning user processes. Most of daemons do fork()+setuid()+execve().
The check introduced in execve() (1) enforces the same limit as in
setuid() and (2) doesn't create similar security issues.
Neil Brown suggested to track what specific process has exceeded the
limit by setting PF_NPROC_EXCEEDED process flag. With the change only
this process would fail on execve(), and other processes' execve()
behaviour is not changed.
Solar Designer suggested to re-check whether NPROC limit is still
exceeded at the moment of execve(). If the process was sleeping for
days between set*uid() and execve(), and the NPROC counter step down
under the limit, the defered execve() failure because NPROC limit was
exceeded days ago would be unexpected. If the limit is not exceeded
anymore, we clear the flag on successful calls to execve() and fork().
The flag is also cleared on successful calls to set_user() as the limit
was exceeded for the previous user, not the current one.
Similar check was introduced in -ow patches (without the process flag).
v3 - clear PF_NPROC_EXCEEDED on successful calls to set_user().
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add FLUSH/FUA support to blktrace. As FLUSH precedes WRITE and/or
FUA follows WRITE, use the same 'F' flag for both cases and
distinguish them by their (relative) position. The end results
look like (other flags might be shown also):
- WRITE: W
- WRITE_FLUSH: FW
- WRITE_FUA: WF
- WRITE_FLUSH_FUA: FWF
Note that we reuse TC_BARRIER due to lack of bit space of act_mask
so that the older versions of blktrace tools will report flush
requests as barriers from now on.
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
REQ_SECURE, REQ_FLUSH and REQ_FUA may all be set on a bio as well as
on a request, so relocate them to the shared part of the enum.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The patch adds empty function of_get_property for non-dt build, so that
drivers migrating to dt can save some '#ifdef CONFIG_OF'.
This also fixes the current Tegra compile problem in linux-next.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: pss - don't use the deprecated function check_region
ALSA: timer - Add NULL-check for invalid slave timer
ALSA: timer - Fix Oops at closing slave timer
ASoC: Acknowledge WM8996 interrupts before acting on them
ASoC: Rename WM8915 to WM8996
ALSA: Fix dependency of CONFIG_SND_TEA575X
ALSA: asihpi - use kzalloc()
ALSA: snd-usb-caiaq: Fix keymap for RigKontrol3
ALSA: snd-usb: Fix uninitialized variable usage
ALSA: hda - Fix a complile warning in patch_via.c
ALSA: hdspm - Fix uninitialized compile warnings
ALSA: usb-audio - add quirk for Keith McMillen StringPort
ALSA: snd-usb: operate on given mixer interface only
ALSA: snd-usb: avoid dividing by zero on invalid input
ALSA: snd-usb: Accept UAC2 FORMAT_TYPE descriptors with bLength > 6
sound: oss/pas2: Remove CLOCK_TICK_RATE dependency from PAS16 driver
ALSA: hda - Use auto-parser for ASUS UX50, Eee PC P901, S101 and P1005
ALSA: hda - Fix digital-mic mono recording on ASUS Eee PC
ASoC: sgtl5000: fix cache handling
ASoC: Disable wm_hubs periodic DC servo update
Archit Taneja