The older smsc911x driver made platform data optional, but the newer one
always requires it, so add proper settings to the BF548-EZKIT.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin SPI driver can be driven by an IRQ now, so declare it in
the board resources.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Try to keep the naming conventions consistent, so:
SPI_ADC_BF533 -> BFIN_SPI_ADC
TWI_LCD -> BFIN_TWI_LCD
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For systems where the core cycles are not a usable tick source (like SMP
or cycles gets updated), enable gptimer0 as an alternative.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
By default, it is routed to async memory address. In GPIO case,
GPIO peripheral PINs should be requested in advance.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Both software emulated and hardware based CTS and RTS are enabled in
serial driver.
The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device. In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only the CTS bit is affected.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
convert BF5{18,27,48}_FAMILY to CONFIG_BF{51,52,54}x as the defines
are redundant in these cases
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
I have a system where UART0 is configured with hardware flow control, but UART1
doesn't have it enabled. Attempting to access UART1 in this configuration
results in the following error in dmesg:
<3>bfin-gpio: GPIO 0 is already reserved as Peripheral by bfin-uart !
<5>Stack from 0082bc7c:
<5> 0082bc88 00404dd6 00000003 00000000 0054051e 004079da 0082bcb4
00000000
<5> 00000003 00000000 0052686c 0113f2a0 005fa3f0 00000032 20515249
00003035
<5> 00427228 00526e50 0113f2e0 005fa3f0 00000032 0113f2e0 0054b748
0000ffff
<5> 22222222 22222222 004e1628 00427304 00000000 00000032 00000023
0054b748
<5> 00487a94 0054b7e8 0054b748 0000000b 00487fb8 0054b748 0054b748
00000001
<5> 0000000a 005fa3f0 009d4fe8 0101e3c0 0054b748 005fa3f0 0050b134
0054b748
<5>
<5>Call Trace:
<4>[<00485c16>] _uart_startup+0x56/0x178
<4>[<004865c8>] _uart_open+0x40/0x3e0
<4>[<0048661c>] _uart_open+0x94/0x3e0
<4>[<0047f1ce>] _init_dev+0x1fa/0x450
<4>[<004e1628>] ___mutex_unlock_slowpath+0x30/0xe8
<4>[<004815da>] _tty_open+0xf6/0x21c
<4>[<0043dab0>] ___path_lookup_intent_open+0x34/0x7c
<4>[<004375e4>] _chrdev_open+0x7c/0x134
<4>[<0043dc2c>] _open_namei+0x60/0x568
<4>[<00433fa2>] ___dentry_open+0x9e/0x188
<4>[<00437568>] _chrdev_open+0x0/0x134
<4>[<0043410c>] _nameidata_to_filp+0x30/0x3c
<4>[<00434152>] _do_filp_open+0x3a/0x44
<4>[<00408826>] _task_running_tick+0x102/0x278
<4>[<0043418e>] _do_sys_open+0x32/0xac
<4>[<0043ede4>] _sys_ioctl+0x28/0x50
<4>[<0043edbc>] _sys_ioctl+0x0/0x50
<4>[<00434224>] _sys_open+0x18/0x20
<4>[<0043420c>] _sys_open+0x0/0x20
<4>[<00418174>] _sys_setuid+0x0/0xc8
This is because the #ifdef's in bfin_serial_5xx.h are messed up. More
specifically, they add/remove the uart_{rts,cts}_pin fields in
bfin_serial_resources based on whether the particular port has rts/cts enabled,
as opposed to when either port has it enabled.
This patch fixed this.
Signed-off-by: Tom Parker <blackfin@tevp.net>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
make sure ANOMALY_05000278/ANOMALY_05000380 is defined for all parts
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- setup P_DEFAULT_BOOT_SPI_CS for every arch based on
the default bootrom behavior and convert all our boards
to it
- revert previous anomaly change ... bf51x is not affected
by anomaly 05000353]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
merge more of the bf54x and !bf54x gpio code together to
cut down on #ifdef mess
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
update bfin-sdh platform data to fix this issue.
Pointed-out-by: Dominik Herwald <d.herwald@dsh-elektronik.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- handle bf531/bf532/bf534/bf536 variants in ipipe.h
- cleanup IPIPE logic for bfin_set_irq_handler()
- cleanup ipipe asm code a bit and add missing ENDPROC()
- simplify IPIPE code in trap_c
- unify some of the IPIPE code and fix style
- simplify DO_IRQ_L1 handling with ipipe code
- revert IRQ_SW_INT# addition from ipipe merge
- remove duplicate get_{c,s}clk() prototypes
]
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- remove duplicated code and headers
- add option allowing arbitrary SDRAM/DDR Timing parameters.
- mark automatically calculated timings as EXPERIMENTAL
- fix comment header block
Related to BUGs:
- kernel boot up fails with CONFIG_BFIN_KERNEL_CLOCK item on.
- kernel does not boot if re-program clocks
[ Mike Frysinger <vapier.adi@gmail.com>
- fix comment header
- mark do_sync static
- document the DMA shutdown
- simplify SIC_IWR handling
- fix ANOMALY_05000265 handling to work as intended ]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
move irq related functions into asm/irq.h and out of the mondo asm/system.h
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Delay PLL_CTL/VR_CTL wrappers as much as possible to avoid
the inter-dependency problems with cdef and common headers
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Blackfin dual core BF561 processor can support SMP like features.
https://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:smp-like
In this patch, we provide SMP extend to some other misc code
Singed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (60 commits)
Blackfin arch: make sure we include the fix for SPORT hysteresis when reprogramming clocks
Blackfin arch: Fix bogus str_ident check in gpio code
Blackfin arch: AD7879 Touchscreen driver
Blackfin arch: introducing bfin_addr_dcachable
Blackfin arch: fix a typo in comments
Blackfin arch: Remove useless head file
Blackfin arch: make sure L2 start and length are always defined (fixes building on BF542)
Blackfin arch: use the Blackfin on-chip ROM to do software reset when possible
Blackfin arch: update anomaly headers to match the latest sheet
Blackfin arch: bfin_reset() is an internal reboot function ... everyone should go through machine_restart()
Blackfin arch: print out error/warning if you are running on the incorrect CPU type
Blackfin arch: remove non-bf54x ifdef logic since this file is only compiled on bf54x parts
Blackfin arch: update board defconfigs
Blackfin arch: Add optional verbose debug
Blackfin arch: emulate a TTY over the EMUDAT/JTAG interface
Blackfin arch: have is_user_addr_valid() check for overflows (like when address is -1)
Blackfin arch: ptrace - fix off-by-one check on end of memory regions
Blackfin arch: Enable framebuffer support for the BF526-EZkit TFT LCD display
Blackfin arch: flash memory map and dm9000 resources updating
Blackfin arch: early prink code still use uart core console functions to parse and set configure option string
...
We now use the sir_dev/irtty_sir/uart/bfin_serial drivers framework
to monitor the TX status.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
move common variables out of serial headers and into the serial driver and
rename "nr_ports" to "nr_active_ports" so as to easily differentiate
between BFIN_UART_NR_PORTS (the # of available) and nr_ports (the # of enabled)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by Appalayagari Sreedhar, make sure we include the fix
for SPORT hysteresis when reprogramming clocks.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Mike Frysinger