The patch added a special get_unmapped_area for framebuffer which
was hooked to the file ops in drivers/video/fbmem.c.
This is needed since v2.6.29-rc1 where nommu vma management was
updated, and mmap of framebuffer caused kernel BUG panic. You may turn
on "Debug the global anon/private NOMMU mapping region tree" config to
such message.
As Documentation/nommu-mmap.txt said,
"To provide shareable character device support, a driver must provide
a file->f_op->get_unmapped_area() operation. The mmap() routines will
call this to get a proposed address for the mapping."
With this change, user space should call mmap for framebuffer using
shared map. Or it can try shared map first, then private map if
failed. This shared map usage is now consistent between mmu and nommu.
The sys_ file may not be a good place for this patch. But there is a
similar one for sparc. I tested a similar patch on nios2nommu, though
I don't have a blackfin board to test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Looks like the big Kconfig cache split/rename missed one spot in the SMP
cache lock headers.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The asm/irq.h header uses anomaly defines, but doesn't make sure to
explicitly include the anomaly header for them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Bill Gatliff & David Brownell pointed out we were missing some
copyrights, and licensing terms in some of the files in
./arch/blackfin, so this fixes things, and cleans them up.
It also removes:
- verbose GPL text(refer to the top level ./COPYING file)
- file names (you are looking at the file)
- bug url (it's in the ./MAINTAINERS file)
- "or later" on GPL-2, when we did not have that right
It also allows some Blackfin-specific assembly files to be under a BSD
like license (for people to use them outside of Linux).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The mcount support that was finally added to the Blackfin gcc port isn't
exactly the same as what ftrace was developed against. Now that the final
gcc version is in place, update the ftrace code to match.
While updating this, fix the swapped arguments to the tracer (signature is
(ip, parent_ip) while we were passing (parent_ip, ip)).
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The elf_fpregset_t type relied on an empty struct in the asm/user.h, but
the transition to asm-generic/user.h dropped that empty struct. Rather
than restore this useless struct, define the only user (elf_fpregset_t)
as an empty struct itself. This fixes building when ELF dump support is
enabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure our interrupt entry code with exact hardware errors handles
anomaly 05000283 (infinite stall in system MMR kill) so we don't stall
while under load.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
No one uses these functions, and some are duplicate of existing C code. So
just punt the whole thing.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The handling of updating the [DI]MEM_CONTROL MMRs does not follow proper
sync procedures as laid out in the Blackfin programming manual. So rather
than audit/fix every call location, create helper functions that do the
right things in order to safely update these MMRs. Then convert all call
sites to use these new helper functions.
While we're fixing the code, drop the workaround for anomaly 05000125 as
that anomaly applies to old versions of silicon that we do not support.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the hardware only provides reporting for the last exception handled,
and the values are valid only when executing the exception handler, we
need to save the context for reporting at a later point. While we do this
for one exception, it doesn't work properly when handling a second one as
the original exception is clobbered by the double fault. So when double
fault debugging is enabled, create a dedicated shadow of these values and
save/restore out of there. Now the crash report properly displays the
first exception as well as the second one.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The protect_page() function was incorrectly setting up the hardware tables
based on possible access capabilities rather than the actual requested
values. This means we would grant more access to mmap-ed pages than we
should have. Once we fix this, we need to tweak the signal generated by
such accesses to aline ourselves with other ports. This allows the LTP
mmap0{5,6,7} cases to run properly.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Allow hardware errors to be caught during early portions of booting, and
leave something in the shadow console that people can use to debug their
system with (to be printed out by the bootloader on next reset).
This enables the hardare error interrupts in head.S, allowing us to find
hardware errors when they happen (well, as much as you can with a hardware
error) and prints out the trace if it is enabled. This will catch errors
(like booting the wrong image on a 533) which previously resulted in a
infinite loop/hang, as well as random hardware errors before before
setup_arch().
To disable this debug only feature - turn off EARLY_PRINTK.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add a memory based shadow console to keep a copy of the printk buffer in a
location which can be found externally. This allows bootloaders to locate
and utilize the log buffer in case of silent (early/resume/etc...) crashes.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The purpose of the EVT14 handler may depend on whether CONFIG_IPIPE is
enabled, albeit its implementation can be the same in both cases. When
the interrupt pipeline is enabled, EVT14 can be used to raise the core
priority level for the running code; when CONFIG_IPIPE is off, EVT14
can be used to lower this level before running softirq handlers.
Rename evt14_softirq to evt_evt14 to pick an identifier that fits
both, which allows to reuse the same vector setup code as well.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
__ipipe_{stall, unstall}_root_raw() identifiers may leave the reader
under the impression that only the virtual state is affected by these
operations, which is wrong. Pick names following the convention used
throughout the interrupt pipeline code.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We handle many exceptions at EVT5 (hardware error level) so that we can
catch exceptions in our exception handling code. Today - if the global
interrupt enable bit (IPEND[4]) is set (interrupts disabled) our trap
handling code goes into a infinite loop, since we need interrupts to be
on to defer things to EVT5.
Normal kernel code should not trigger this for any reason as IPEND[4] gets
cleared early (when doing an interrupt context save) and the kernel stack
there should be sane (or something much worse is happening in the system).
But there have been a few times where this has happened, so this change
makes sure we dump a proper crash message even when things have gone south.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The default values of HARDIRQ_BITS and PREEMPT_BITS in common code leads to
build failure:
In file included from include/linux/interrupt.h:12,
from include/linux/kernel_stat.h:8,
from arch/blackfin/kernel/asm-offsets.c:32:
include/linux/hardirq.h:66:2: error: #error PREEMPT_ACTIVE is too low!
So until that gets resolved, just declare our own default value again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On Blackfin SMP, a per-cpu loops_per_jiffy is pointless since both cores
always run at the same CCLK. In addition, the current implementation has
flaws since the main consumer for loops_per_jiffy (asm/delay.h) uses the
global kernel loops_per_jiffy and not the per_cpu one. So punt all of the
per-cpu handling and go back to the global shared one.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The interrupt context save logic incorrectly stored the address of the
IPEND register rather than its value due to a missing dereference. While
we're here, also enable this code for all kernel debugging scenarios and
not just when KGDB is enabled.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This anomaly only applies to the BF527-0.1, not the BF526-0.1, and not any
other revision of the BF527. So make sure we don't go returning 0xffff
for other cases.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent deprecation of dma_sync_{sg,single} ironically broke Blackfin
systems. This is because we don't define dma_sync_sg_for_cpu at all, so
until the DMA asm-generic conversion/cleanup is done after the next
release, simply stub out the dma_sync_sg_for_{cpu,device} functions.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't support the BF535 at all, and the exception 0x2A text specific to
it is pretty verbose and confusing (since the behavior is simply odd), so
punt it to keep the noise down.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF526-EZBRD changed SDRAM chips between board revisions, so create a
timing table that can accommodate both.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We defined SDRAM_tRAS to TRAS_4, but then wrongly defined SDRAM_tRAS_num
to 3.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many aspects of the Blackfin memory map is exactly the same across all
variants. Rather than copy and paste all of these duplicated values in
each header, unify all of these into the common Blackfin memory map header
file. In the process, push down BF561 SMP specific stuff to the BF561
specific header to keep the noise down.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current cache options don't really represent the hardware features.
They end up setting different aspects of the hardware so that the end
result is to turn on/off the cache. Unfortunately, when we hit cache
problems with the hardware, it's difficult to test different settings to
root cause the problem. The current settings also don't cleanly allow for
different caching behaviors with different regions of memory.
So split the configure options such that they properly reflect the settings
that are applied to the hardware.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The kgdb (in multiple places) and traps code developed pretty much
identical checks for how to access different regions of the Blackfin
memory map, but each wasn't 100%, so unify them to avoid duplication,
bitrot, and bugs with edge cases.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
Convert most arches to use asm-generic/kmap_types.h.
Move the KM_FENCE_ macro additions into asm-generic/kmap_types.h,
controlled by __WITH_KM_FENCE from each arch's kmap_types.h file.
Would be nice to be able to add custom KM_types per arch, but I don't yet
see a nice, clean way to do that.
Built on x86_64, i386, mips, sparc, alpha(tonyb), powerpc(tonyb), and
68k(tonyb).
Note: avr32 should be able to remove KM_PTE2 (since it's not used) and
then just use the generic kmap_types.h file. Get avr32 maintainer
approval.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Chou