Update pci_set_vga_state to call arch dependent functions to enable Legacy
VGA I/O transactions to be redirected to correct target.
[akpm@linux-foundation.org: make pci_register_set_vga_state() __init]
Signed-off-by: Mike Travis <travis@sgi.com>
LKML-Reference: <201002022238.o12McE1J018723@imap1.linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs. As
anticipated, we've run into a buggy BIOS:
[ 0.081818] pci 0000:00:14.0: reg 10: [io 0x6000-0x7fff]
[ 0.081906] pci 0000:00:14.0: reg 14: [io 0x6100-0x61ff]
[ 0.082015] pci 0000:00:14.0: reg 18: [io 0x6200-0x63ff]
[ 0.082917] pci 0000:00:14.2: reg 20: [io 0xe000-0xe00f]
[ 0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[ 0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[ 0.088816] PCI: pci_cache_line_size set to 32 bytes
[ 0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[ 0.089052] pci 0000:00:14.0: can't reserve [io 0x6100-0x61ff]
This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k. In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff). This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Tested-by: Leigh Porter <leigh@leighporter.org>
Tested-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Callers (acpi_memhotplug.c, dock.c and others) check for the return
value of acpi_bus_add() and assume a valid device was returned in
case zero was returned.
Thus return -ENODEV if no device was found in acpi_bus_scan and
propagate this through acpi_bus_add and acpi_bus_start.
Also remove a confusing comment in acpiphp_glue.c, acpi_bus_scan
will and cannot invoke if acpi_bus_add returns no valid device.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The aer_inject module hangs in aer_inject() when checking the device's
error masks. The hang is due to a recursive use of the aer_inject lock.
The aer_inject() routine grabs the lock while processing the error and then
calls pci_read_config_dword to read the masks. The pci_read_config_dword
routine is earlier overridden by pci_read_aer, which among other things,
grabs the aer_inject lock.
Fixed by moving the pci_read_config_dword calls to read the masks to before
the lock is taken.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The Correcteable/Uncorrectable Error Mask Registers are used by PCIe AER
driver which will controls the reporting of individual errors to PCIe RC
via PCIe error messages.
If hardware masks special error reporting to RC, the aer_inject driver
should not inject aer error.
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Youquan, Song <youquan.song@intel.com>
Acked-by: Ying, Huang <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It turns out that some PCI devices require extra delays when changing
power state from D3 to D0 (and the other way around). Although this
is against the PCI specification, we can handle it quite easily by
allowing drivers to define arbitrary D3 delays for devices known to
require extra time for switching power states.
Introduce additional field d3_delay in struct pci_dev and use it to
store the value of the device's D0->D3 delay, in miliseconds. Make
the PCI PM core code use the per-device d3_delay unless
pci_pm_d3_delay is greater (in which case the latter is used).
[This also allows the driver to specify d3_delay shorter than the
10 ms required by the PCI standard if the device is known to be able
to handle that.]
Make the sky2 driver set d3_delay to 150 for devices handled by it.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14730 which is a
listed regression from 2.6.30.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit e0cd516 "PCI: derive nearby CPUs from device's instead of bus'
NUMA information" causes an null pointer dereference when reading from
the sysfs attributes local_cpu* on Intel machines with no ACPI NUMA
proximity info, since dev->numa_node gets set to -1 for all PCI devices,
which then gets passed to cpumask_of_node.
Add a check to prevent this.
Signed-off-by: David John <davidjon@xenontk.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduced by commit 5b889bf23 ("PCI: Fix build if quirks are not
enabled"), which made the pci_dev_reset_methods[] array static and
'const', but didn't then change the code to match, and use a const
pointer when moving it to quirks.c.
Trivially fixed by just adding the required 'const' to the iterator
variable.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit b9c3b26641 ("PCI: support
device-specific reset methods") the kernel build is broken if
CONFIG_PCI_QUIRKS is unset.
Fix this by moving pci_dev_specific_reset() to drivers/pci/quirks.c and
providing an empty replacement for !CONFIG_PCI_QUIRKS builds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dmar_tbl is declared as __initdata, but dmar_ir_support() is not declared
as an __init function. Fix is simple since the only caller of dmar_ir_support
(intr_remapping_supported) is an __init function.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/cardbus: Add a fixup hook and fix powerpc
PCI: change PCI nomenclature in drivers/pci/ (non-comment changes)
PCI: change PCI nomenclature in drivers/pci/ (comment changes)
PCI: fix section mismatch on update_res()
PCI: add Intel 82599 Virtual Function specific reset method
PCI: add Intel USB specific reset method
PCI: support device-specific reset methods
PCI: Handle case when no pci device can provide cache line size hint
PCI/PM: Propagate wake-up enable for PCIe devices too
vgaarbiter: fix a typo in the vgaarbiter Documentation
The cardbus code creates PCI devices without ever going through the
necessary fixup bits and pieces that normal PCI devices go through.
There's in fact a commented out call to pcibios_fixup_bus() in there,
it's commented because ... it doesn't work.
I could make pcibios_fixup_bus() do the right thing on powerpc easily
but I felt it cleaner instead to provide a specific hook pci_fixup_cardbus
for which a weak empty implementation is provided by the PCI core.
This fixes cardbus on powerbooks and probably all other PowerPC
platforms which was broken completely for ever on some platforms and
since 2.6.31 on others such as PowerBooks when we made the DMA ops
mandatory (since those are setup by the fixups).
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Changing occurrences of variants of PCI-X and PCIe to the PCI-SIG
terms listed in the "Trademark and Logo Usage Guidelines".
http://www.pcisig.com/developers/procedures/logos/Trademark_and_Logo_Usage_Guidelines_updated_112206.pdf
Patch is limited to drivers/pci/ and changes concern non-comment parts or
anything that might be visible to the user.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Handle device specific timeout and use FLR.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add a new type of quirk for resetting devices at pci_dev_reset time.
This is necessary to handle device with nonstandard reset procedures,
especially useful for guest drivers.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Dexuan Cui <dexuan.cui@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prior to this patch, if pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, ...)
returns 0 for all dev, pci_cache_line_size ends up set to zero
(instead of pci_dfl_cache_line_size).
This patch ensures the pci_cache_line_size = pci_dfl_cache_line_size
setting in the above scenario.
This happens in case of a kvm-88 guest (where, consequently, the rtl8139
NIC failed to initialize).
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Csaba Henk <csaba@gluster.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Having read the PM part of the PCIe 2.0 specification more carefully
I think that it was a mistake to restrict the wake-up enable
propagation to non-PCIe devices, because if we do not request
control of the root ports' PME registers via OSC, PCIe PME is
supposed to be handled by the platform, just like the non-PCIe PME.
Even if we do that, the wake-up propagation is done to allow the
devices to wake up the system from sleep states which involves the
platform anyway, so it won't hurt.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.infradead.org/iommu-2.6:
implement early_io{re,un}map for ia64
Revert "Intel IOMMU: Avoid memory allocation failures in dma map api calls"
intel-iommu: ignore page table validation in pass through mode
intel-iommu: Fix oops with intel_iommu=igfx_off
intel-iommu: Check for an RMRR which ends before it starts.
intel-iommu: Apply BIOS sanity checks for interrupt remapping too.
intel-iommu: Detect DMAR in hyperspace at probe time.
dmar: Fix build failure without NUMA, warn on bogus RHSA tables and don't abort
iommu: Allocate dma-remapping structures using numa locality info
intr_remap: Allocate intr-remapping table using numa locality info
dmar: Allocate queued invalidation structure using numa locality info
dmar: support for parsing Remapping Hardware Static Affinity structure
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: Update version to 20091112.
ACPICA: Add additional module-level code support
ACPICA: Deploy new create integer interface where appropriate
ACPICA: New internal utility function to create Integer objects
ACPICA: Add repair for predefined methods that must return sorted lists
ACPICA: Fix possible fault if return Package objects contain NULL elements
ACPICA: Add post-order callback to acpi_walk_namespace
ACPICA: Change package length error message to an info message
ACPICA: Reduce severity of predefined repair messages, Warning to Info
ACPICA: Update version to 20091013
ACPICA: Fix possible memory leak for Scope ASL operator
ACPICA: Remove possibility of executing _REG methods twice
ACPICA: Add repair for bad _MAT buffers
ACPICA: Add repair for bad _BIF/_BIX packages
* 'timers-for-linus-hpet' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Make WARN_ON understandable
x86: arch specific support for remapping HPET MSIs
intr-remap: generic support for remapping HPET MSIs
x86, hpet: Simplify the HPET code
x86, hpet: Disable per-cpu hpet timer if ARAT is supported
commit eb3fa7cb51 said Intel IOMMU
Intel IOMMU driver needs memory during DMA map calls to setup its
internal page tables and for other data structures. As we all know
that these DMA map calls are mostly called in the interrupt context
or with the spinlock held by the upper level drivers(network/storage
drivers), so in order to avoid any memory allocation failure due to
low memory issues, this patch makes memory allocation by temporarily
setting PF_MEMALLOC flags for the current task before making memory
allocation calls.
We evaluated mempools as a backup when kmem_cache_alloc() fails
and found that mempools are really not useful here because
1) We don't know for sure how much to reserve in advance
2) And mempools are not useful for GFP_ATOMIC case (as we call
memory alloc functions with GFP_ATOMIC)
(akpm: point 2 is wrong...)
The above description doesn't justify to waste system emergency memory
at all. Non MM subsystem must not use PF_MEMALLOC. Memory reclaim need
few memory, anyone must not prevent it. Otherwise the system cause
mysterious hang-up and/or OOM Killer invokation.
Plus, akpm already pointed out what we should do.
Then, this patch revert it.
Cc: Keshavamurthy Anil S <anil.s.keshavamurthy@intel.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We are seeing a bug when booting w/ iommu=pt with current upstream
(bisect blames 19943b0e30 "intel-iommu:
Unify hardware and software passthrough support).
The issue is specific to this loop during identity map initialization
of each device:
domain_context_mapping_one(si_domain, ..., CONTEXT_TT_PASS_THROUGH)
...
/* Skip top levels of page tables for
* iommu which has less agaw than default.
*/
for (agaw = domain->agaw; agaw != iommu->agaw; agaw--) {
pgd = phys_to_virt(dma_pte_addr(pgd));
if (!dma_pte_present(pgd)) { <------ failing here
spin_unlock_irqrestore(&iommu->lock, flags);
return -ENOMEM;
}
This box has 2 iommu's in it. The catchall iommu has MGAW == 48, and
SAGAW == 4. The other iommu has MGAW == 39, SAGAW == 2.
The device that's failing the above pgd test is the only device connected
to the non-catchall iommu, which has a smaller address width than the
domain default. This test is not necessary since the context is in PT
mode and the ASR is ignored.
Thanks to Don Dutile for discovering and debugging this one.
Cc: stable@kernel.org
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The hotplug notifier will call find_domain() to see if the device in
question has been assigned an IOMMU domain. However, this should never
be called for devices with a "dummy" domain, such as graphics devices
when intel_iommu=igfx_off is set and the corresponding IOMMU isn't even
initialised. If you do that, it'll oops as it dereferences the (-1)
pointer.
The notifier function should check iommu_no_mapping() for the
device before doing anything else.
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some HP BIOSes report an RMRR region (a region which needs a 1:1 mapping
in the IOMMU for a given device) which has an end address lower than its
start address. Detect that and warn, rather than triggering the
BUG() in dma_pte_clear_range().
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The BIOS errors where an IOMMU is reported either at zero or a bogus
address are causing problems even when the IOMMU is disabled -- because
interrupt remapping uses the same hardware. Ensure that the checks get
applied for the interrupt remapping initialisation too.
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many BIOSes will lie to us about the existence of an IOMMU, and claim
that there is one at an address which actually returns all 0xFF.
We need to detect this early, so that we know we don't have a viable
IOMMU and can set up swiotlb before it's too late.
Cc: stable@kernel.org
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
x86/amd-iommu: Remove amd_iommu_pd_table
x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
x86/amd-iommu: Cleanup DTE flushing code
x86/amd-iommu: Introduce iommu_flush_device() function
x86/amd-iommu: Cleanup attach/detach_device code
x86/amd-iommu: Keep devices per domain in a list
x86/amd-iommu: Add device bind reference counting
x86/amd-iommu: Use dev->arch->iommu to store iommu related information
x86/amd-iommu: Remove support for domain sharing
x86/amd-iommu: Rearrange dma_ops related functions
x86/amd-iommu: Move some pte allocation functions in the right section
x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
x86/amd-iommu: Use get_device_id and check_device where appropriate
x86/amd-iommu: Move find_protection_domain to helper functions
x86/amd-iommu: Simplify get_device_resources()
x86/amd-iommu: Let domain_for_device handle aliases
x86/amd-iommu: Remove iommu specific handling from dma_ops path
x86/amd-iommu: Remove iommu parameter from __(un)map_single
x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
...
Remove a stray space in pci_save_state().
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit ae21ee65e8 "PCI: acs p2p upsteram
forwarding enabling" doesn't actually enable ACS.
Add a function to pci core to allow an IOMMU to request that ACS
be enabled. The existing mechanism of using iommu_found() in the pci
core to know when ACS should be enabled doesn't actually work due to
initialization order; iommu has only been detected not initialized.
Have Intel and AMD IOMMUs request ACS, and Xen does as well during early
init of dom0.
Cc: Allen Kay <allen.m.kay@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This problem happened when removing PCIe root port using PCI logical
hotplug operation.
The immediate cause of this problem is that the pointer to invalid
data structure is passed to pcie_update_aspm_capable() by
pcie_aspm_exit_link_state(). When pcie_aspm_exit_link_state() received
a pointer to root port link, it unconfigures the root port link and
frees its data structure at first. At this point, there are not links
to configure under the root port and the data structure for root port
link is already freed. So pcie_aspm_exit_link_state() must not call
pcie_update_aspm_capable() and pcie_config_aspm_path().
This patch fixes the problem by changing pcie_aspm_exit_link_state()
not to call pcie_update_aspm_capable() and pcie_config_aspm_path() if
the specified link is root port link.
------------[ cut here ]------------
kernel BUG at drivers/pci/pcie/aspm.c:606!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:40/0000:40:13.0/remove
CPU 1
Modules linked in: shpchp
Pid: 9345, comm: sysfsd Not tainted 2.6.32-rc5 #98 ProLiant DL785 G6
RIP: 0010:[<ffffffff811df69b>] [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP: 0018:ffff88082a2f5ca0 EFLAGS: 00010202
RAX: 0000000000000e77 RBX: ffff88182cc3e000 RCX: ffff88082a33d006
RDX: 0000000000000001 RSI: ffffffff811dff4a RDI: ffff88182cc3e000
RBP: ffff88082a2f5cc0 R08: ffff88182cc3e000 R09: 0000000000000000
R10: ffff88182fc00180 R11: ffff88182fc00198 R12: ffff88182cc3e000
R13: 0000000000000000 R14: ffff88182cc3e000 R15: ffff88082a2f5e20
FS: 00007f259a64b6f0(0000) GS:ffff880864600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00007feb53f73da0 CR3: 000000102cc94000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sysfsd (pid: 9345, threadinfo ffff88082a2f4000, task ffff88082a33cf00)
Stack:
ffff88182cc3e000 ffff88182cc3e000 0000000000000000 ffff88082a33cf00
<0> ffff88082a2f5cf0 ffffffff811dff52 ffff88082a2f5cf0 ffff88082c525168
<0> ffff88402c9fd2f8 ffff88402c9fd2f8 ffff88082a2f5d20 ffffffff811d7db2
Call Trace:
[<ffffffff811dff52>] pcie_aspm_exit_link_state+0xf5/0x11e
[<ffffffff811d7db2>] pci_stop_bus_device+0x76/0x7e
[<ffffffff811d7d67>] pci_stop_bus_device+0x2b/0x7e
[<ffffffff811d7e4f>] pci_remove_bus_device+0x15/0xb9
[<ffffffff811dcb8c>] remove_callback+0x29/0x3a
[<ffffffff81135aeb>] sysfs_schedule_callback_work+0x15/0x6d
[<ffffffff81072790>] worker_thread+0x19d/0x298
[<ffffffff8107273b>] ? worker_thread+0x148/0x298
[<ffffffff81135ad6>] ? sysfs_schedule_callback_work+0x0/0x6d
[<ffffffff810765c0>] ? autoremove_wake_function+0x0/0x38
[<ffffffff810725f3>] ? worker_thread+0x0/0x298
[<ffffffff8107629e>] kthread+0x7d/0x85
[<ffffffff8102eafa>] child_rip+0xa/0x20
[<ffffffff8102e4bc>] ? restore_args+0x0/0x30
[<ffffffff81076221>] ? kthread+0x0/0x85
[<ffffffff8102eaf0>] ? child_rip+0x0/0x20
Code: 89 e5 8a 50 48 31 c0 c0 ea 03 83 e2 07 e8 b2 de fe ff c9 48 98 c3 55 48 89 e5 41 56 49 89 fe 41 55 41 54 53 48 83 7f 10 00 74 04 <0f> 0b eb fe 48 8b 05 da 7d 63 00 4c 8d 60 e8 4c 89 e1 eb 24 4c
RIP [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP <ffff88082a2f5ca0>
---[ end trace 6ae0f65bdeab8555 ]---
Reported-by: Alex Chiang <achiang@hp.com>
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pci_cleanup_aer_correct_error_status() function has been
#if 0'd out since 2.6.25. Time to remove the dead code.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The current implementation of pci_cleanup_aer_uncorrect_error_status
only clears either fatal or non-fatal error status bits depending
on the state of the I/O channel. This implementation will then often
leave some bits set after PCI error recovery completes. The uncleared bit
settings will then be falsely reported the next time an AER interrupt is
generated for that hierarchy. An easy way to illustrate this issue is to
use the aer-inject module to simultaneously inject both an uncorrectable
non-fatal and uncorrectable fatal error. One of the errors will not be
cleared.
This patch resolves this issue by unconditionally clearing all bits in
the AER uncorrectable status register. All settings and corrective action
strategies are saved and determined before
pci_cleanup_aer_uncorrect_error_status is called, so this change should not
affect errory handling functionality.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove 'port_type' field in struct pcie_port_data(), because we can
get port type information from struct pci_dev. With this change, this
patch also does followings:
- Remove struct pcie_port_data because it no longer has any field.
- Remove portdrv private definitions about port type (PCIE_RC_PORT,
PCIE_SW_UPSTREAM_PORT and PCIE_SW_DOWNSTREAM_PORT), and use generic
definitions instead.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add missing service irqs cleanup in the error code path of
pcie_port_device_register().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Call pci_enable_device() before initializing service irqs, because
legacy interrupt is initialized in pci_enable_device() on some
architectures.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch cleans up the service irqs initialization as follows:
- Remove 'irq_mode' field in pcie_port_data and related definitions,
which is not needed because we can get the same information from
'is_msix', 'is_msi' and 'pin' fields in struct pci_dev.
- Change the name of 'vectors' argument of assign_interrupt_mode() to
'irqs' because it holds irq numbers actually. People might confuse
it with CPU vector or MSI/MSI-X vector.
- Change function name assign_interrupt_mode() to init_service_irqs()
becasuse we no longer have 'irq_mode' data structure, and new name
is more straightforward (IMO).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No reason to check PME capability outside get_port_device_capability().
Do it in get_port_device_capability().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe port type is already stored in 'pcie_type' field of struct
pci_dev. So we don't need to get it from pci configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current port bus driver implementation, pcie_device allocation,
initialization and registration are done in separated functions. Doing
those in one function make the code simple and easier to read.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We don't need pcie_port_device_probe() because we can get pci
device/port type using pci_is_pcie() and 'pcie_type' fields in struct
pci_dev. Remove pcie_port_device_probe().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prior to 1f82de10 we always initialized the upper 32bits of the
prefetchable memory window, regardless of the address range used.
Now we only touch it for a >32bit address, which means the upper32
registers remain whatever the BIOS initialized them too.
It's valid for the BIOS to set the upper32 base/limit to
0xffffffff/0x00000000, which makes us program prefetchable ranges
like 0xffffffffabc00000 - 0x00000000abc00000
Revert the chunk of 1f82de10 that made this conditional so we always
write the upper32 registers and remove now unused pref_mem64 variable.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pcie_flr routine writes the device control register with the FLR bit
set clearing all other fields for the FLR duration. Among other fields,
the Max_Payload_Size is also cleared which can cause errors if there are
transactions lurking in the HW pipeline. The patch replaces the blank
write with read-modify-write of the control register keeping the other
fields intact.
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
So we can catch if the driver sets an incorrect dma_mask.
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we stop the kthread, we may end up up'ing the sem twice, which seems
unintended.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The existing interface only has a pre-order callback. This change
adds an additional parameter for a post-order callback which will
be more useful for bus scans. ACPICA BZ 779.
Also update the external calls to acpi_walk_namespace.
http://www.acpica.org/bugzilla/show_bug.cgi?id=779
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enabling power fault detected event notification in current pciehp
might cause power fault interrupt storm on some machines. On those
machines. On those machines, power fault detected bit in the slot
status register was set again immediately when it is cleared in the
interrupt service routine, and next power fault detected interrupt was
notified again. Therefore, disable power fault detected event
notification for now.
This patch also removes unnecessary handling for power fault cleared
event because this event is not supported by PCIe spec.
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change for PCI hotplug to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Changes for PCIe AER driver to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change for PCIe ASPM driver to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change for PCI core to use pci_is_pcie() instead of checking
pci_dev->is_pcie.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in pciehp driver. This avoids unnecessary search in PCI
configuration space. This patch also removes 'cap_base' field in
struct controller, that was used to hold PCIe capability offset by
pciehp itself.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI hotplug core. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCIe ASPM driver. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI Express Port Bus driver. This avoids unnecessary serarch
in PCI configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCIe AER driver. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI core code. This avoids unnecessary search in PCI
configuration space.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 86cf898e1d ("intel-iommu: Check for
'DMAR at zero' BIOS error earlier.") was supposed to work by pretending
not to detect an IOMMU if it was actually being reported by the BIOS at
physical address zero.
However, the intel_iommu_init() function is called unconditionally, as
are the corresponding functions for other IOMMU hardware.
So the patch only worked if you have RAM above the 4GiB boundary. It
caused swiotlb to be initialised when no IOMMU was detected during early
boot, and thus the later IOMMU init would refuse to run.
But if you have less RAM than that, swiotlb wouldn't get set up and the
IOMMU _would_ still end up being initialised, even though we never
claimed to detect it.
This patch also sets the dmar_disabled flag when the error is detected
during the initial detection phase -- so that the later call to
intel_iommu_init() will return without doing anything, regardless of
whether swiotlb is used or not.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/users/dwmw2/iommu-2.6.32:
intel-iommu: Support PCIe hot-plug
intel-iommu: Obey coherent_dma_mask for alloc_coherent on passthrough
intel-iommu: Check for 'DMAR at zero' BIOS error earlier.
To support PCIe hot plug in IOMMU, we register a notifier to respond to device
change action.
When the notifier gets BUS_NOTIFY_UNBOUND_DRIVER, it removes the device
from its DMAR domain.
A hot added device will be added into an IOMMU domain when it first does IOMMU
op. So there is no need to add more code for hot add.
Without the patch, after a hot-remove, a hot-added device on the same
slot will not work.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The model for IOMMU passthrough is that decent devices that can cope
with DMA to all of memory get passthrough; crappy devices with a limited
dma_mask don't -- they get to use the IOMMU anyway.
This is done on the basis that IOMMU passthrough is usually wanted for
performance reasons, and it's only the decent PCI devices that you
really care about performance for, while the crappy 32-bit ones like
your USB controller can just use the IOMMU and you won't really care.
Unfortunately, the check for this was only looking at dev->dma_mask, not
at dev->coherent_dma_mask. And some devices have a 32-bit
coherent_dma_mask even though they have a full 64-bit dma_mask.
Even more unfortunately, fixing that simple oversight would upset
certain broken HP devices. Not only do they have a 32-bit
coherent_dma_mask, but they also have a tendency to do stray DMA to
unmapped addresses. And then they die when they take the DMA fault they
so richly deserve.
So if we do the 'correct' fix, it'll mean that affected users have to
disable IOMMU support completely on "a large percentage of servers from
a major vendor."
Personally, I have little sympathy -- given that this is the _same_
'major vendor' who is shipping machines which claim to have IOMMU
support but have obviously never _once_ booted a VT-d capable OS to do
any form of QA. But strictly speaking, it _would_ be a regression even
though it only ever worked by fluke.
For 2.6.33, we'll come up with a quirk which gives swiotlb support
for this particular device, and other devices with an inadequate
coherent_dma_mask will just get normal IOMMU mapping.
The simplest fix for 2.6.32, though, is just to jump through some hoops
to try to allocate coherent DMA memory for such devices in a place that
they can reach. We'd use dma_generic_alloc_coherent() for this if it
existed on IA64.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I'm not entirely sure it needs to go into 32, but it's probably the right
thing to do. Another way of explaining the patch is:
- we currently pick the _first_ exactly matching bus resource entry, but
the _last_ inexactly matching one. Normally first/last shouldn't
matter, but bus resource entries aren't actually all created equal: in
a transparent bus, the last resources will be the parent resources,
which we should generally try to avoid unless we have no choice. So
"first matching" is the thing we should always aim for.
- the patch is a bit bigger than it needs to be, because I simplified the
logic at the same time. It used to be a fairly incomprehensible
if ((res->flags & IORESOURCE_PREFETCH) && !(r->flags & IORESOURCE_PREFETCH))
best = r; /* Approximating prefetchable by non-prefetchable */
and technically, all the patch did was to make that complex choice be
even more complex (it basically added a "&& !best" to say that if we
already gound a non-prefetchable window for the prefetchable resource,
then we won't override an earlier one with that later one: remember
"first matching").
- So instead of that complex one with three separate conditionals in one,
I split it up a bit, and am taking advantage of the fact that we
already handled the exact case, so if 'res->flags' has the PREFETCH
bit, then we already know that 'r->flags' will _not_ have it. So the
simplified code drops the redundant test, and does the new '!best' test
separately. It also uses 'continue' as a way to ignore the bus
resource we know doesn't work (ie a prefetchable bus resource is _not_
acceptable for anything but an exact match), so it turns into:
/* We can't insert a non-prefetch resource inside a prefetchable parent .. */
if (r->flags & IORESOURCE_PREFETCH)
continue;
/* .. but we can put a prefetchable resource inside a non-prefetchable one */
if (!best)
best = r;
instead. With the comments, it's now six lines instead of two, but it's
conceptually simpler, and I _could_ have written it as two lines:
if ((res->flags & IORESOURCE_PREFETCH) && !best)
best = r; /* Approximating prefetchable by non-prefetchable */
but I thought that was too damn subtle.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If HW IOMMU initialization fails (Intel VT-d often does this,
typically due to BIOS bugs), we fall back to nommu. It doesn't
work for the majority since nowadays we have more than 4GB
memory so we must use swiotlb instead of nommu.
The problem is that it's too late to initialize swiotlb when HW
IOMMU initialization fails. We need to allocate swiotlb memory
earlier from bootmem allocator. Chris explained the issue in
detail:
http://marc.info/?l=linux-kernel&m=125657444317079&w=2
The current x86 IOMMU initialization sequence is too complicated
and handling the above issue makes it more hacky.
This patch changes x86 IOMMU initialization sequence to handle
the above issue cleanly.
The new x86 IOMMU initialization sequence are:
1. we initialize the swiotlb (and setting swiotlb to 1) in the case
of (max_pfn > MAX_DMA32_PFN && !no_iommu). dma_ops is set to
swiotlb_dma_ops or nommu_dma_ops. if swiotlb usage is forced by
the boot option, we finish here.
2. we call the detection functions of all the IOMMUs
3. the detection function sets x86_init.iommu.iommu_init to the
IOMMU initialization function (so we can avoid calling the
initialization functions of all the IOMMUs needlessly).
4. if the IOMMU initialization function doesn't need to swiotlb
then sets swiotlb to zero (e.g. the initialization is
sucessful).
5. if we find that swiotlb is set to zero, we free swiotlb
resource.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: chrisw@sous-sol.org
Cc: dwmw2@infradead.org
Cc: joerg.roedel@amd.com
Cc: muli@il.ibm.com
LKML-Reference: <1257849980-22640-10-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This changes detect_intel_iommu() to set intel_iommu_init() to
iommu_init hook if detect_intel_iommu() finds the IOMMU.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: chrisw@sous-sol.org
Cc: dwmw2@infradead.org
Cc: joerg.roedel@amd.com
Cc: muli@il.ibm.com
LKML-Reference: <1257849980-22640-6-git-send-email-fujita.tomonori@lab.ntt.co.jp>
[ -v2: build fix for the !CONFIG_DMAR case ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Chris Wright has some patches which let us fall back to swiotlb nicely
if IOMMU initialisation fails. But those are a bit much for 2.6.32.
Instead, let's shift the check for the biggest problem, the HP and Acer
BIOS bug which reports a DMAR at physical address zero. That one can
actually be checked much earlier -- before we even admit to having
detected an IOMMU in the first place. So the swiotlb init goes ahead as
we want.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SPIN_LOCK_UNLOCKED is deprecated. Use DEFINE_SPINLOCK instead.
Make the lock static while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If firmware doesn't grant over native hotplug control through ACPI
_OSC method, we must not evaluate OSHP.
Acked-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In case of AMD CPU northbridge functions this NUMA information might
differ. Here is an example from a 4-socket system.
Currently Linux shows
root@hagen:/sys/devices/pci0000:00/0000:00:1a.4# cat numa_node
0
root@hagen:/sys/devices/pci0000:00/0000:00:1a.4# cat local_cpu*
0-3
00000000,0000000f
which is not correct for northbridge functions as the local CPUs
are those of the same socket.
With this patch and a quirk for AMD CPU NB functions Linux can
do better and correctly show
root@hagen:/sys/devices/pci0000:00/0000:00:1a.4# cat numa_node
2
root@hagen:/sys/devices/pci0000:00/0000:00:1a.4# cat local_cpu*
8-11
00000000,00000f00
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the following BUG_ON() problem reported by Alex Chiang.
This problem happened when removing PCIe root port using PCI logical
hotplug operation.
The immediate cause of this problem is that the pointer to invalid
data structure is passed to pcie_update_aspm_capable() by
pcie_aspm_exit_link_state(). When pcie_aspm_exit_link_state() received
a pointer to root port link, it unconfigures the root port link and
frees its data structure at first. At this point, there are not links
to configure under the root port and the data structure for root port
link is already freed. So pcie_aspm_exit_link_state() must not call
pcie_update_aspm_capable() and pcie_config_aspm_path().
This patch fixes the problem by changing pcie_aspm_exit_link_state()
not to call pcie_update_aspm_capable() and pcie_config_aspm_path() if
the specified link is root port link.
------------[ cut here ]------------
kernel BUG at drivers/pci/pcie/aspm.c:606!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:40/0000:40:13.0/remove
CPU 1
Modules linked in: shpchp
Pid: 9345, comm: sysfsd Not tainted 2.6.32-rc5 #98 ProLiant DL785 G6
RIP: 0010:[<ffffffff811df69b>] [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP: 0018:ffff88082a2f5ca0 EFLAGS: 00010202
RAX: 0000000000000e77 RBX: ffff88182cc3e000 RCX: ffff88082a33d006
RDX: 0000000000000001 RSI: ffffffff811dff4a RDI: ffff88182cc3e000
RBP: ffff88082a2f5cc0 R08: ffff88182cc3e000 R09: 0000000000000000
R10: ffff88182fc00180 R11: ffff88182fc00198 R12: ffff88182cc3e000
R13: 0000000000000000 R14: ffff88182cc3e000 R15: ffff88082a2f5e20
FS: 00007f259a64b6f0(0000) GS:ffff880864600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00007feb53f73da0 CR3: 000000102cc94000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sysfsd (pid: 9345, threadinfo ffff88082a2f4000, task ffff88082a33cf00)
Stack:
ffff88182cc3e000 ffff88182cc3e000 0000000000000000 ffff88082a33cf00
<0> ffff88082a2f5cf0 ffffffff811dff52 ffff88082a2f5cf0 ffff88082c525168
<0> ffff88402c9fd2f8 ffff88402c9fd2f8 ffff88082a2f5d20 ffffffff811d7db2
Call Trace:
[<ffffffff811dff52>] pcie_aspm_exit_link_state+0xf5/0x11e
[<ffffffff811d7db2>] pci_stop_bus_device+0x76/0x7e
[<ffffffff811d7d67>] pci_stop_bus_device+0x2b/0x7e
[<ffffffff811d7e4f>] pci_remove_bus_device+0x15/0xb9
[<ffffffff811dcb8c>] remove_callback+0x29/0x3a
[<ffffffff81135aeb>] sysfs_schedule_callback_work+0x15/0x6d
[<ffffffff81072790>] worker_thread+0x19d/0x298
[<ffffffff8107273b>] ? worker_thread+0x148/0x298
[<ffffffff81135ad6>] ? sysfs_schedule_callback_work+0x0/0x6d
[<ffffffff810765c0>] ? autoremove_wake_function+0x0/0x38
[<ffffffff810725f3>] ? worker_thread+0x0/0x298
[<ffffffff8107629e>] kthread+0x7d/0x85
[<ffffffff8102eafa>] child_rip+0xa/0x20
[<ffffffff8102e4bc>] ? restore_args+0x0/0x30
[<ffffffff81076221>] ? kthread+0x0/0x85
[<ffffffff8102eaf0>] ? child_rip+0x0/0x20
Code: 89 e5 8a 50 48 31 c0 c0 ea 03 83 e2 07 e8 b2 de fe ff c9 48 98 c3 55 48 89 e5 41 56 49 89 fe 41 55 41 54 53 48 83 7f 10 00 74 04 <0f> 0b eb fe 48 8b 05 da 7d 63 00 4c 8d 60 e8 4c 89 e1 eb 24 4c
RIP [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP <ffff88082a2f5ca0>
---[ end trace 6ae0f65bdeab8555 ]---
Reported-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There are a lot of codes that searches PCI express capability offset
in the PCI configuration space using pci_find_capability(). Caching it
in the struct pci_dev will reduce unncecessary search. This patch adds
an additional 'pcie_cap' fields into struct pci_dev, which is
initialized at pci device scan time (in set_pcie_port_type()).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This makes PCI resource management messages more consistent and adds a few
new messages to aid debugging.
Whenever we assign resources to a device, update a BAR, or change a
bridge aperture, it's worth noting it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since we have a struct device, we might as well use dev_printk. Note that
both pr_debug() and dev_dbg() are completely compiled out unless DEBUG or
DYNAMIC_DEBUG is defined.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Messages about PME# being supported and enabled/disabled are probably
useful for debug, but maybe don't need to be on the console.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 3b073eda has removed pci_find_slot, so there's no point in
mentioning it in the config description as one of the deprecated APIs
there are enabled by PCI_LEGACY and still used by some drivers.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jesse accidentally applied v1 [1] of the patchset instead of v2 [2]. This
is the diff between v1 and v2.
The changes in this patch are:
- tidied vsprintf stack buffer to shrink and compute size more
accurately
- use %pR for decoding and %pr for "raw" (with type and flags) instead
of adding %pRt and %pRf
[1] http://lkml.org/lkml/2009/10/6/491
[2] http://lkml.org/lkml/2009/10/13/441
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
AMD 813x rev. B1 (like rev. B2) devices generate no interrupts if
quirk_disable_amd_813x_boot_interrupt is executed, add an exception.
http://bugzilla.kernel.org/show_bug.cgi?id=14159
Patch also adds missing cases for DECLARE_PCI_FIXUP_RESUME and
DECLARE_PCI_FIXUP_FINAL calls to quirk_disable_amd_813x_boot_interrupt.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Tested-by: Gabriele Giorgetti <g.giorgetti@teamsystem.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Using list_for_each_entry instead of list_for_each allows us to
enhance readability and minorly reduce some stack usage.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch moves PCI I/O APIC support from acpiphp to a separate driver.
Like pciehp and shpchp, acpiphp handles PCI hotplug, i.e., addition and
removal of PCI adapters. But in addition, acpiphp handles some ACPI
hotplug, such as the addition of new host bridges, and the I/O APIC
support was tangled up with that.
I don't think the I/O APIC support needs to be in acpiphp; PCI I/O APICs
usually appear as a function on a PCI host bridge, and we'll enumerate the
APIC before any of the devices behind the bridge that use it.
As far as I know, nobody actually uses I/O APIC hotplug. It depends on
acpi_register_ioapic(), which is only implemented for ia64, and I don't
think any vendors have supported I/O chassis hotplug yet.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
CC: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
CC: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Replaced some error return values in aer_inject. Use -ENODEV when we
can't find a device and -ENOTTY when the device does not support PCIe AER.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add support for PCI domains (segments) to aer_inject.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Added the pci_get_domain_and_slot_function which is analogous to
pci_get_bus_and_slot. It returns a pci_dev given a domain (segment) number,
bus number, and devnr. Like pci_get_bus_and_slot,
pci_get_domain_bus_and_slot holds a reference to the returned pci_dev.
Converted pci_get_bus_and_slot to a wrapper that calls
pci_get_domain_bus_and_slot with the domain hard-coded to 0.
This routine was patterned off code suggested by Bjorn Helgaas.
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change to populate the subsystem vendor and subsytem device IDs for
PCI-PCI bridges that implement the PCI Subsystem Vendor ID capability.
Previously bridges left subsystem vendor IDs unpopulated.
Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Feedback from Hidetoshi Seto and Kenji Kaneshige incorporated. This
correctly handles PCI-X bridges, PCIe root ports and endpoints, and
prints debug messages when invalid/reserved types are found in the
HEST. PCI devices not in domain/segment 0 are not represented in
HEST, thus will be ignored.
Today, the PCIe Advanced Error Reporting (AER) driver attaches itself
to every PCIe root port for which BIOS reports it should, via ACPI
_OSC.
However, _OSC alone is insufficient for newer BIOSes. Part of ACPI
4.0 is the new APEI (ACPI Platform Error Interfaces) which is a way
for OS and BIOS to handshake over which errors for which components
each will handle. One table in ACPI 4.0 is the Hardware Error Source
Table (HEST), where BIOS can define that errors for certain PCIe
devices (or all devices), should be handled by BIOS ("Firmware First
mode"), rather than be handled by the OS.
Dell PowerEdge 11G server BIOS defines Firmware First mode in HEST, so
that it may manage such errors, log them to the System Event Log, and
possibly take other actions. The aer driver should honor this, and
not attach itself to devices noted as such.
Furthermore, Kenji Kaneshige reminded us to disallow changing the AER
registers when respecting Firmware First mode. Platform firmware is
expected to manage these, and if changes to them are allowed, it could
break that firmware's behavior.
The HEST parsing code may be replaced in the future by a more
feature-rich implementation. This patch provides the minimum needed
to prevent breakage until that implementation is available.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prevent unnecessary power off at initialization time. If slot power
is already off, we don't need to power off the slot.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp returns successfully on read/write failure with dummy
state values. It should return error instead.
With this patch, pciehp no longer uses hotplug_slot_info data
structure. So this also removes hotplug_slot_info related code. But
note that it still allocates hotplug_slot_info because it is required
by pci hotplug core.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp driver creates 'attention' and 'latch' files even if
the controller doesn't support them. In this case, the contents of
those files are meaningless and unpredictable. Those files should be
created only if the controller has the corresponding capabilities.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove wrong workaround for BAD DLLP error, which confused surprise
down error with DLL errors.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp doesn't handle Data Link Layer State Changed Event
notification. So it needs to be disabled at initialization time,
otherwise other event notifications are not generated.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When probing for ROM BAR size, we should not change bits 1:10 in this
BAR, because these bits are marked as "reserved for future use" in PCI
spec, so changing them might have side effects.
No such issue for I/O or memory, as there is an implementation note in
PCI spec which explicitly allows writing 0xfffffffff there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch is predicated on Jeremy's patch in include/xen/xen.h. It'll
prevent ACS init unless the platform has both an IOMMU and we're running
as dom0.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Note: dom0 checking in v4 has been separated out into 2/2.
This patch enables P2P upstream forwarding in ACS capable PCIe switches.
It solves two potential problems in virtualization environment where a PCIe
device is assigned to a guest domain using a HW iommu such as VT-d:
1) Unintentional failure caused by guest physical address programmed
into the device's DMA that happens to match the memory address range
of other downstream ports in the same PCIe switch. This causes the PCI
transaction to go to the matching downstream port instead of go to the
root complex to get translated by VT-d as it should be.
2) Malicious guest software intentionally attacks another downstream
PCIe device by programming the DMA address into the assigned device
that matches memory address range of the downstream PCIe port.
We are in process of implementing device filtering software in KVM/XEN
management software to allow device assignment of PCIe devices behind a PCIe
switch only if it has ACS capability and with the P2P upstream forwarding bits
enabled. This patch is intended to work for both KVM and Xen environments.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Reviewed-by: Mathew Wilcox <willy@linux.intel.com>
Reviewed-by: Chris Wright <chris@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As a followup to 71a082efc9, it's conceivable
that some vendors may expose PCI hotplug functionality through both vendor
mechanisms and ACPI. The native mechanism will generally be a superset of
any functionality provided via ACPI, so the acpiphp driver should always
be initialised after any others. Change the link order such that acpiphp
will not be initialised until any other statically linked drivers have had
an opportunity to claim the hardware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_dfl_cache_line_size is marked as __initdata but referenced by
pci_init() which is __devinit. Make it __devinitdata instead of
__initdata.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For non hotplug PCI devices, the system firmware usually configures
CLS correctly. For pccard devices system firmware can't do it and
Linux PCI layer doesn't do it either. Unfortunately this leads to
poor performance for certain devices (sata_sil). Unless MWI, which
requires separate configuration, is to be used, CLS doesn't affect
correctness, so the configuration should be harmless.
This patch makes pci_set_cacheline_size() always built and export it
and make pccard call it during attach.
Please note that some other PCI hotplug drivers (shpchp and pciehp)
also configure CLS on hotplug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Greg KH <greg@kroah.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Axel Birndt <towerlexa@gmx.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
sparc64 is now the only user of PCI_CACHE_LINE_BYTES. Drop it and set
pci_dfl_cache_line_size from pcibios_init() instead and drop
PCI_CACHE_LINE_BYTES handling from generic pci code.
Orignally-From: David Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Till now, CLS has been determined either by arch code or as
L1_CACHE_BYTES. Only x86 and ia64 set CLS explicitly and x86 doesn't
always get it right. On most configurations, the chance is that
firmware configures the correct value during boot.
This patch makes pci_init() determine CLS by looking at what firmware
has configured. It scans all devices and if all non-zero values
agree, the value is used. If none is configured or there is a
disagreement, pci_dfl_cache_line_size is used. arch can set the dfl
value (via PCI_CACHE_LINE_BYTES or pci_dfl_cache_line_size) or
override the actual one.
ia64, x86 and sparc64 updated to set the default cls instead of the
actual one.
While at it, declare pci_cache_line_size and pci_dfl_cache_line_size
in pci.h and drop private declarations from arch code.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 308cf8e13f. This
patch had trouble with transparent bridges, among other things. A more
readable and correct version should land in 2.6.33.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit d43c36dc6b ("headers: remove
sched.h from interrupt.h") left some build errors in some configurations
due to drivers having depended on getting header files "accidentally".
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Combined several one-liners from Ingo into one single patch - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/~dwmw2/iommu-2.6.32:
x86: Move pci_iommu_init to rootfs_initcall()
Run pci_apply_final_quirks() sooner.
Mark pci_apply_final_quirks() __init rather than __devinit
Rename pci_init() to pci_apply_final_quirks(), move it to quirks.c
intel-iommu: Yet another BIOS workaround: Isoch DMAR unit with no TLB space
intel-iommu: Decode (and ignore) RHSA entries
intel-iommu: Make "Unknown DMAR structure" message more informative
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Prevent AER driver from being loaded on non-root port PCIE devices
PCI: get larger bridge ranges when space is available
PCI: pci.c: fix kernel-doc notation
PCI quirk: TI XIO200a erroneously reports support for fast b2b transfers
PCI PM: Read device power state from register after updating it
PCI: remove pci_assign_resource_fixed()
PCI: PCIe portdrv: remove "-driver" from driver name
Having this as a device_initcall() means that some real device drivers
can actually initialise _before_ the quirks are run, which is wrong.
We want it to run _before_ device_initcall(), but _after_ fs_initcall(),
since some arch-specific PCI initialisation like pcibios_assign_resources()
is done at fs_initcall().
We could use rootfs_initcall() but I actually want to use that for the
IOMMU initialisation, which has to come after the quirks, but still
before the real devices. So use fs_initcall_sync() instead -- since this
is entirely synchronous, it doesn't hurt that it'll escape the
synchronisation.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This function may have done more in the past, but all it does now is
apply the PCI_FIXUP_FINAL quirks. So name it sensibly and put it where
it belongs.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
A bug was seen on boards using a PLX 8518 switch device which advertises
AER on each of it's transparent bridges. The AER driver was loaded for
each bridge and this driver tried to access the AER source ID register
whenever an interrupt occured on the shared PCI INTX lines. The source
ID register does not exist on non root port PCIE device's which
advertise AER and trying to access this register causes a unsupported
request error on the bridge. Thus, when the next interrupt occurs,
another error is found and the non existent source ID register is
accessed again, and so it goes on.
The result is a spammed dmesg with unsupported request PCI express
errors on the bridge device that the AER driver is loaded against.
Reported-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Found one system:
[ 71.120590] pci 0000:40:05.0: scanning behind bridge, config 4f4a40, pass 0
[ 71.138283] PCI: Scanning bus 0000:4a
[ 71.140341] pci 0000:4a:00.0: found [15b3:6278] class 000c06 header type 00
[ 71.157173] pci 0000:4a:00.0: reg 10 64bit mmio: [0x000000-0x0fffff]
[ 71.161697] pci 0000:4a:00.0: reg 18 64bit mmio pref: [0x000000-0x7fffff]
[ 71.179403] pci 0000:4a:00.0: reg 20 64bit mmio pref: [0x000000-0xfffffff]
[ 71.185366] pci 0000:4a:00.0: calling quirk_resource_alignment+0x0/0x1dd
[ 71.200846] pci 0000:4a:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 71.219623] PCI: Fixups for bus 0000:4a
[ 71.222194] pci 0000:40:05.0: bridge 32bit mmio: [0xcf000000-0xcf0fffff]
[ 71.238662] pci 0000:40:05.0: bridge 64bit mmio pref: [0xcd800000-0xcdffffff]
[ 71.255793] PCI: Bus scan for 0000:4a returning with max=4a
Device needs a big pref mmio, but BIOS doesn't allocate mmio to it aside
from a small MMIO range. Later, the kernel will not allocate resources to
that to the device:
[ 99.574030] pci 0000:4a:00.0: BAR 4: can't allocate mem resource [0xd0000000-0xcdffffff]
[ 99.580102] pci 0000:4a:00.0: BAR 2: got res [0xcd800000-0xcdffffff] bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.602307] pci 0000:4a:00.0: BAR 2: moved to bus [0xcd800000-0xcdffffff] flags 0x12120c
[ 99.615991] pci 0000:4a:00.0: BAR 0: got res [0xcf000000-0xcf0fffff] bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.634499] pci 0000:4a:00.0: BAR 0: moved to bus [0xcf000000-0xcf0fffff] flags 0x120204
[ 99.654318] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.658766] pci 0000:40:05.0: IO window: disabled
[ 99.675478] pci 0000:40:05.0: MEM window: 0xcf000000-0xcf0fffff
[ 99.681663] pci 0000:40:05.0: PREFETCH window: 0x000000cd800000-0x000000cdffffff
So try to get a big range in the pci bridge if there is no child using
that range. With the patch we get:
[ 99.104525] pci 0000:4a:00.0: BAR 4: got res [0xfc080000000-0xfc08fffffff] bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.123624] pci 0000:4a:00.0: BAR 4: moved to bus [0xfc080000000-0xfc08fffffff] flags 0x12120c
[ 99.131977] pci 0000:4a:00.0: BAR 2: got res [0xfc090000000-0xfc0907fffff] bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.149788] pci 0000:4a:00.0: BAR 2: moved to bus [0xfc090000000-0xfc0907fffff] flags 0x12120c
[ 99.169248] pci 0000:4a:00.0: BAR 0: got res [0xc0200000-0xc02fffff] bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.189508] pci 0000:4a:00.0: BAR 0: moved to bus [0xc0200000-0xc02fffff] flags 0x120204
[ 99.206402] pci 0000:40:05.0: PCI bridge, secondary bus 0000:4a
[ 99.210637] pci 0000:40:05.0: IO window: disabled
[ 99.224856] pci 0000:40:05.0: MEM window: 0xc0200000-0xc03fffff
[ 99.230019] pci 0000:40:05.0: PREFETCH window: 0x000fc080000000-0x000fc097ffffff
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This quirk will disable fast back to back transfer on the secondary bus
segment of the TI Bridge.
Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After attempting to change the power state of a PCI device
pci_raw_set_power_state() doesn't check if the value it wrote into
the device's PCI_PM_CTRL register has been stored in there, but
unconditionally modifies the device's current_state field to reflect
the change. This may cause problems to happen if the power state of
the device hasn't been changed in fact, because it will make the PCI
PM core make a wrong assumption.
To prevent such situations from happening modify
pci_raw_set_power_state() so that it reads the device's PCI_PM_CTRL
register after writing into it and uses the value read from the
register to update the device's current_state field. Also make it
print a message saying that the device refused to change its power
state as requested (returning an error code in such cases would cause
suspend regressions to appear on some systems, where device drivers'
suspend routines return error codes if pci_set_power_state() fails).
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Adrian commented out this function in 2baad5f96b, but I don't think
it's even worth cluttering the file with the unused code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No need to include "-driver" in the driver name.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Allocate dma-remapping structures using numa locality info. On platforms
having remapping hardware units span different nodes, this enables
optimized dma-remapping transalation structures access by remapping hardware.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allocate intr-remapping table using numa locality info. On platforms
having remapping hardware units span different nodes, this enables
optimized intr-remapping table entry access by remapping hardware.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for parsing Remapping Hardware Static Affinity (RHSA) structure.
This enables identifying the association between remapping hardware units and
the corresponding proximity domain. This enables to allocate transalation
structures closer to the remapping hardware unit.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Asus decided to ship a BIOS which configures sound DMA to go via the
dedicated IOMMU unit, but assigns precisely zero TLB entries to that
unit. Which causes the whole thing to deadlock, including the DMA
traffic on the _other_ IOMMU units. Nice one.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 15b8dd53f5 changed info->hardware_id from a static array to
a pointer. If hardware_id is non-NULL, it points to a NULL-terminated
string, so we don't need to terminate it explicitly. However, it may
be NULL; in that case, we *can't* add a NULL terminator.
This causes a NULL pointer dereference oops for devices without _HID.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Lin Ming <ming.m.lin@intel.com>
CC: Bob Moore <robert.moore@intel.com>
CC: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I recently got a system where the DMAR table included a couple of RHSA
(remapping hardware static affinity) entries. Rather than printing a
message about an "Unknown DMAR structure," it would probably be more
useful to dump the RHSA structure (as other DMAR structures are dumped).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We might as well print the type of the DMAR structure we don't know how
to handle when skipping it. Then someone getting this message has a
chance of telling whether the structure is just bogus, or if there
really is something valid that the kernel doesn't know how to handle.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/iommu-2.6: (23 commits)
intel-iommu: Disable PMRs after we enable translation, not before
intel-iommu: Kill DMAR_BROKEN_GFX_WA option.
intel-iommu: Fix integer wrap on 32 bit kernels
intel-iommu: Fix integer overflow in dma_pte_{clear_range,free_pagetable}()
intel-iommu: Limit DOMAIN_MAX_PFN to fit in an 'unsigned long'
intel-iommu: Fix kernel hang if interrupt remapping disabled in BIOS
intel-iommu: Disallow interrupt remapping if not all ioapics covered
intel-iommu: include linux/dmi.h to use dmi_ routines
pci/dmar: correct off-by-one error in dmar_fault()
intel-iommu: Cope with yet another BIOS screwup causing crashes
intel-iommu: iommu init error path bug fixes
intel-iommu: Mark functions with __init
USB: Work around BIOS bugs by quiescing USB controllers earlier
ia64: IOMMU passthrough mode shouldn't trigger swiotlb init
intel-iommu: make domain_add_dev_info() call domain_context_mapping()
intel-iommu: Unify hardware and software passthrough support
intel-iommu: Cope with broken HP DC7900 BIOS
iommu=pt is a valid early param
intel-iommu: double kfree()
intel-iommu: Kill pointless intel_unmap_single() function
...
Fixed up trivial include lines conflict in drivers/pci/intel-iommu.c
The following 64 bit promotions are necessary to handle memory above the
4GiB boundary correctly.
[dwmw2: Fix the second part not to need 64-bit arithmetic at all]
Signed-off-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If end_pfn is equal to (unsigned long)-1, then the loop will never end.
Seen on 32-bit kernel, but could have happened on 64-bit too once we get
hardware that supports 64-bit guest addresses.
Change both functions to a 'do {} while' loop with the test at the end,
and check for the PFN having wrapper round to zero.
Reported-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Tested-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This means we're limited to 44-bit addresses on 32-bit kernels, and
makes it sane for us to use 'unsigned long' for PFNs throughout.
Which is just as well, really, since we already do that.
Reported-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Tested-by: Benjamin LaHaise <ben.lahaise@neterion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since slot_cap field in struct controller contains physical slot
number informationq, we don't need number field in struct slot.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The struct hpc_ops seems a set of hooks to controller specific
routines. But, it is meaningless because no hotplug controller driver
follows this framework.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since we have a pointer to pcie_device in struct controller, we don't
need a pointer to pci_dev.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The crit_sect mutex defined in struct controller is to serialize
hot-plug operations against multiple slots under the same bus. But,
since PCIe doesnstream port has only one slot at most, it is
meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The slot number can be calculated only by physical slot number field
in the slot capabilities register. So the first_slot field in struct
controller is meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since the device number of the hot-slot under the PCIe downstream port
is always 0, the slot_device_offset field in the slot is meaningless
and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The hp_slot field is to identify the slot under the same
controller. But, since PCIe downstream port has only one slot at most,
it is meaningless and we don't need it.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The device field in the struct slot is not necessary because it is
always 0 in pciehp driver.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The bus field in struct slot is not necessary.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The slot_num_inc field in struct controller is unused and meaningless
in pciehp driver.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since PCIe downstream port has only one slot at most, we don't need
num_slots field in struct controller. Note that struct controller
itself doesn't exist if PCIe downstream port has no slot.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since PCIe downstream port has only one slot at most, we don't need
'slot_list' linked list to manage multiple slots under the port.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When booting with pci=nomsi aer causes lost interrupts and
lockdep inversions.
So check if MSIs are not disabled before initializing the aer
driver.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The definition of the ASPM support field in the Link Capabilities
Register had been changed by the "ASPM optionality ECN" as follows:
<Before>
00b Reserved
01b L0s Supported
10b Reserved
11b L0s and L1 Supported
<After>
00b No ASPM Support
01b L0s Supported
10b L1 Supported
11b L0s and L1 Supported
Current linux ASPM driver doesn't enable ASPM if the support field is
00b or 10b. So there is no impact about 00b. But current linux ASPM
driver doesn't enable L1 if the support field is 10b. With this patch,
10b (L1 support) is handled properly.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
* 'x86-txt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, intel_txt: clean up the impact on generic code, unbreak non-x86
x86, intel_txt: Handle ACPI_SLEEP without X86_TRAMPOLINE
x86, intel_txt: Fix typos in Kconfig help
x86, intel_txt: Factor out the code for S3 setup
x86, intel_txt: tboot.c needs <asm/fixmap.h>
intel_txt: Force IOMMU on for Intel TXT launch
x86, intel_txt: Intel TXT Sx shutdown support
x86, intel_txt: Intel TXT reboot/halt shutdown support
x86, intel_txt: Intel TXT boot support
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (52 commits)
Input: bcm5974 - silence uninitialized variables warnings
Input: wistron_btns - add keymap for AOpen 1557
Input: psmouse - use boolean type
Input: i8042 - use platform_driver_probe
Input: i8042 - use boolean type where it makes sense
Input: i8042 - try disabling and re-enabling AUX port at close
Input: pxa27x_keypad - allow modifying keymap from userspace
Input: sunkbd - fix formatting
Input: i8042 - bypass AUX IRQ delivery test on laptops
Input: wacom_w8001 - simplify querying logic
Input: atkbd - allow setting force-release bitmap via sysfs
Input: w90p910_keypad - move a dereference below a NULL test
Input: add twl4030_keypad driver
Input: matrix-keypad - add function to build device keymap
Input: tosakbd - fix cleaning up KEY_STROBEs after error
Input: joydev - validate axis/button maps before clobbering current ones
Input: xpad - add USB ID for the drumkit controller from Rock Band
Input: w90p910_keypad - rename driver name to match platform
Input: add new driver for Sentelic Finger Sensing Pad
Input: psmouse - allow defining read-only attributes
...
This patch cleans up acpi_run_hpp() and follows the style of acpi_run_hpx():
- remove unnecessary METHOD_NAME__HPP #define
- use ACPI_ALLOCATE_BUFFER rather than evaluating _HPP twice
- validate _HPP package length (defined as 4 by the spec)
- avoid ref to undefined data if FW provides < 4 elements
- remove temporary nui[] array
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_configure_slot() rather than the acpiphp-specific
decode_hpp() and program_hpp().
Unlike the previous acpiphp-specific code, pci_configure_slot() programs
PCIe settings when an _HPX method provides them, so acpiphp-managed PCIe
devices can now be configured.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_configure_slot() rather than the SHPC-specific
program_fw_provided_values().
Unlike the previous SHPC-specific code, pci_configure_slot() programs PCIe
settings when an _HPX method provides them, so if it's possible to have an
SHPC-managed PCIe device, it can now be configured.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_configure_slot() rather than the PCIe-specific
program_fw_provided_values().
Unlike the previous pciehp-specific code, we now walk through subordinate
devices even if there are no settings for the parent. This should be
harmless because we won't change anything unless we discover firmware
settings farther down.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds a new pci_configure_slot() function that programs the
PCI bus characteristics for a newly-added device. This is based on
code in pciehp_pci.c, but should be generic enough to be used by pciehp,
shpchp, and acpiphp.
The hotplug_params struct and the program_hpp_typeX() functions are based
on the ACPI definitions, but they aren't really ACPI-specific, and there's
no alternate implementation, so I don't see the need to abstract them yet.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes acpi_get_hp_params_from_firmware() take a
pci_dev rather than a pci_bus and makes it return a standard
int errno rather than acpi_status.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We always look up hotplug_params with decode_hpp() immediately before using
them, so we don't need to save them in the acpiphp_bridge struct. This
patch follows the example of program_fw_provided_values() in pciehp_pci.c
and shpchp_pci.c by just keeping the params on the stack while we need them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
decode_hpp() looks up hotplug PCI parameters from ACPI and saves them
in the acpiphp_bridge structure. These parameters (in bridge->hpp) are
only used by the acpiphp_set_hpp_values() -> program_hpp() path. In
that path, we always call decode_hpp() before program_hpp(), so there's
no need to do it in init_bridge_misc().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some PCI devices fail if their standard configuration registers are
restored twice in a row. Prevent this from happening by making
pci_restore_state() clear the saved_state flag of the device right
after the device's standard configuration registers have been
populated with the previously saved values.
Simplify PCI PM callbacks by removing the direct clearing of
state_saved from them, as it shouldn't be necessary any more (except
in pci_pm_thaw(), where it has to be cleared, so that the values saved
during the "freeze" phase of hibernation are not used later by mistake).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently pci_pm_resume() always returns 0, which makes the error
variable defined in there a bit pointless. Make pci_pm_resume()
return error codes obtained from drivers' callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit c82f63e411
(PCI: check saved state before restore) pcie_portdrv_slot_reset()
may not work correctly if dev->error_state is equal to
pci_channel_io_frozen, because dev->state_saved need not be set at
that time. Fix this issue by setting dev->state_saved before
pci_restore_state() is called in pcie_portdrv_slot_reset().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
acpi_pci_detect_ejectable() goes through effort to convert its
struct pci_bus arg to an acpi_handle, but every time we use this
interface, we already have the handle available.
So let's just use the handle instead of converting back and forth.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Instead of constantly evaluating _ADR and _SEG over and over again,
let's simplify our lives by using:
acpi_pci_find_root() for root bridges
acpi_get_pci_dev() for p2p bridges
This change eliminates some copy 'n paste code and also allows us
to simplify some internal interfaces.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (25 commits)
pata_rz1000: use printk_once
ahci: kill @force_restart and refine CLO for ahci_kick_engine()
pata_cs5535: add pci id for AMD based CS5535 controllers
ahci: Add AMD SB900 SATA/IDE controller device IDs
drivers/ata: use resource_size
sata_fsl: Defer non-ncq commands when ncq commands active
libata: add SATA PMP revision information for spec 1.2
libata: fix off-by-one error in ata_tf_read_block()
ahci: Gigabyte GA-MA69VM-S2 can't do 64bit DMA
ahci: make ahci_asus_m2a_vm_32bit_only() quirk more generic
dmi: extend dmi_get_year() to dmi_get_date()
dmi: fix date handling in dmi_get_year()
libata: unbreak TPM filtering by reorganizing ata_scsi_pass_thru()
sata_sis: convert to slave_link
sata_sil24: always set protocol override for non-ATAPI data commands
libata: Export AHCI capabilities
libata: Delegate nonrot flag setting to SCSI
[libata] Add pata_rdc driver for RDC ATA devices
drivers/ata: Remove unnecessary semicolons
libata: remove spindown skipping and warning
...
BIOS clear DMAR table INTR_REMAP flag to disable interrupt remapping. Current
kernel only check interrupt remapping(IR) flag in DRHD's extended capability
register to decide interrupt remapping support or not. But IR flag will not
change when BIOS disable/enable interrupt remapping.
When user disable interrupt remapping in BIOS or BIOS often defaultly disable
interrupt remapping feature when BIOS is not mature.Though BIOS disable
interrupt remapping but intr_remapping_supported function will always report
to OS support interrupt remapping if VT-d2 chipset populated. On this
cases, kernel will continue enable interrupt remapping and result kernel panic.
This bug exist on almost all platforms with interrupt remapping support.
This patch add DMAR table INTR_REMAP flag check before enable interrupt
remapping.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Current kernel enable interrupt remapping only when all the vt-d unit support
interrupt remapping. So it is reasonable we should also disallow enabling
intr-remapping if there any io-apics that are not listed under vt-d units.
Otherwise we can run into issues.
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some PCI devices (not PCI Express), like PCI add-on cards, can
generate PME#, but they don't have any special platform wake-up
support. For this reason, even if they generate PME# to wake up the
system from a sleep state, wake-up events are not generated by the
platform.
It turns out that, at least on some systems, PCI bridges and the PCI
host bridge have ACPI GPEs associated with them that, if enabled to
generate wake-up events, allow the system to wake up if one of the
add-on devices asserts PME# while the system is in a sleep state.
Following this observation, if a PCI device without direct ACPI
wake-up support is prepared to wake up the system during a transition
into a sleep state (eg. suspend to RAM), try to configure the bridges
on the path from the device to the root bridge to wake-up the system.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce a new PCI device flag, wakeup_prepared, to prevent PCI
wake-up preparation code from being executed twice in a row for the
same device and for the same purpose.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move a debug message from acpi_pci_sleep_wake() to
acpi_pm_device_sleep_wake() and use the standard dev_*() macros
in there.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rework the PCI wake-up code so that it's easier to read without
changing the functionality.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In general a BIOS may goof or we may hotplug in a hotplug controller.
In either case the kernel needs to reserve resources for plugging
in more devices in the future instead of creating a minimal resource
assignment.
We already do this for cardbus bridges I am just adding a variant
for pcie bridges.
v2: Make testing for pcie hotplug bridges based on a flag.
So far we only set the flag for pcie but a header_quirk
could easily be added for the non-standard pci hotplug
bridges.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a very old quirk for the intel E7502 E7320 and E7525 memory
controller hubs that disables usage of msi interrupts on pcie hotplug
bridges of those devices, and disables changing the affinity of irqs.
Today all we have to do to disable msi on a specific device is to set
dev->no_msi, which is much more straightforward than the previous
logic.
The re-running of this fixup after pci hotplug happens below these
devices is totally bogus. All of the state we change is pure software
state and we don't change the hardware at all. Which means hotplug on
the lower devices doesn't have a chance to change this state. So we
can safely remove the special case from the pciehp driver and the pcie
portdriver.
I suspect the special case was someone's expermental debug code that
slipped in. Certainly it isn't mentioned in commit
6fb8880a61510295aece04a542767161f624dffe aka BKrev:
41966101LJ_ogfOU0m2aE6teZfQnuQ where the code first appears.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Multiple bits might be set in the Uncorrectable Error Status
register. But aer_print_error_source() only report a error of
the lowest bit set in the error status register.
So print strings for all bits unmasked and set.
And check First Error Pointer to mark the error occured first.
This FEP is not valid when the corresponing bit of the Uncorrectable
Error Status register is not set, or unimplemented or undefined.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ERR_{,UN}CORRECTABLE_ERROR_MASK are set of error bits which linux know,
set of PCI_ERR_COR_* and PCI_ERR_UNC_* defined in linux/pci_regs.h.
This masks make aerdrv not to report errors of unknown bit, while aerdrv
have ability to report such undefined errors as "Unknown Error Bit %2d".
OTOH aerdrv_errprint does not have any check of setting in mask register.
So it could report masked wrong error by finding bit in status without
knowing that the bit is masked in the mask register.
This patch changes aerdrv to use mask state in mask register propely
instead of defined/hardcoded ERR_{,UN}CORRECTABLE_ERROR_MASK.
This change prevents aerdrv from reporting masked error, and also enable
reporting unknown errors.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The static buffer errmsg_buff[] is used only for building error
message in fixed format, and is protected by a spinlock.
This patch removes this buffer and the spinlock.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The flag AER_MULTI_ERROR_VALID_FLAG in info->flag does mean that the
root port receives multiple error messages. Error messages can be
posted from different devices, so it does not mean that each reported
device has multiple errors.
If there are multiple error devices and the root port has valid error
source ID, it would be nice to report which device is the error source
reported first.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In case of multiple errors, struct aer_err_info would be reused among
all reported devices. So the info->status should be initialized before
recycled. Otherwise error of one device might be reported as the error
of another device. Also info->flags has similar problem on reporting
TLP header.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Definitions of MASK macros in aerdrv_errprint.c are tricky and unsafe.
For example, AER_AGENT_TRANSMITTER_MASK(_sev, _stat) does work like:
static inline func(int _sev, int _stat)
{
if (_sev == AER_CORRECTABLE)
return (_stat & (PCI_ERR_COR_REP_ROLL|PCI_ERR_COR_REP_TIMER));
else
return (_stat & PCI_ERR_COR_REP_ROLL);
}
In case of else path here, for uncorrectable errors, testing bits in
_stat by PCI_ERR_COR_* does not make sense because _stat should have only
PCI_ERR_UNC_* bits originated in uncorrectable error status register.
But at this time this is safe because uncorrectable error using bit
position same to PCI_ERR_COR_REP_ROLL(= bit position 8) is not defined.
Likewise, AER_AGENT_COMPLETER_MASK is always PCI_ERR_UNC_COMP_ABORT but
it works because bit 15 of correctable error status is not defined.
It means that these MASK macros will turn to be wrong once if new error
is defined. (In fact, bit 15 of correctable is now defined in PCIe 2.1)
This patch changes these MASK macros to be more strict, not to return
PCI_ERR_COR_* bits for uncorrectable error status and vise versa.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add ids module parameter which allows specifying initial IDs for the
pci-stub driver. When built into the kernel, pci-stub is linked
before any real pci drivers and by setting up IDs from initialization
it can prevent built-in drivers from attaching to specific devices.
While at it, make pci_stub_probe() print out about devices it grabbed
to weed out "but my controller isn't being probed" bug reports.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Separate out pci_add_dynid() from store_new_id() and export it so that
in-kernel code can add PCI IDs dynamically. As the function will be
available regardless of HOTPLUG, put it and pull pci_free_dynids()
outside of CONFIG_HOTPLUG.
This will be used by pci-stub to initialize initial IDs via module
param.
While at it, remove bogus get_driver() failure check.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add support for PCI-E 5.0 GT/s in max_bus_speed and cur_bus_speed.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The L0s state can be managed separately for each direction (upstream
direction and downstream direction) of the link. But in the current
implementation, those are mixed up. With this patch, L0s for each
direction are managed separately.
To maintain three states (upstream direction L0s, downstream L0s and
L1), 'aspm_support', 'aspm_enabled', 'aspm_capable', 'aspm_disable'
and 'aspm_default' fields in struct pcie_link_state are changed to
3-bit from 2-bit. The 'latency' field is separated to two 'latency_up'
and 'latency_dw' fields to maintain exit latencies for each direction
of the link. For L0, 'latency_up.l0' and 'latency_dw.l0' are used to
configure upstream direction L0s and downstream direction L0s
respectively. For L1, larger value of 'latency_up.l1' and
'latency_dw.l1' is considered as L1 exit latency.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current implementation, ASPM L0s/L1 is disabled for all links
in the hierarchy if one of the link doesn't meet latency requirement.
But we can partially enable ASPM L0s/L1 on sub-tree in the hierarchy.
This patch allows partial L0s/L1 enablement in the hierarchy. And it
also reduce the calculation cost of ASPM configuration very much.
In the previous implementation, all links were enabled with the same
state. With this patch, enabled state for each link is determined
simply as follows (the 'requested' is from policy_to_aspm_state()).
enabled = requested & (link->aspm_capable & link->aspm_disable)
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_capable' field to maintain the capable ASPM setting of
the link. By the 'aspm_capable', we don't need to recheck latency
every time ASPM policy is changed.
Each bit in 'aspm_capable' is associated to ASPM state (L0S/L1). The
bit is set if the associated ASPM state is supported by the link and
it satisfies the latency requirement (i.e. exit latency < endpoint
acceptable latency). The 'aspm_capable' is updated when
- an endpoint device is added (boot time or hot-plug time)
- an endpoint device is removed (hot-unplug time)
- PCI power state is changed.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'aspm_disable' flag to manage disabled ASPM state more
robust way.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix possible NULL dereference in pcie_aspm_exit_link_state(). This
patch also cleanup some code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the following check in __pcie_aspm_config_link() because it
nerver be true.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We must not clear bits in 'aspm_enabled' using 'aspm_support', or
'aspm_enabled' and 'aspm_default' might be different from the actual
state. In addtion, 'aspm_default' should be intialized even if
'aspm_support' is 0.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds the most recent additions to the list of 82576 device IDs
to the list of devices needing the SR-IOV quirk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Background:
Graphic devices are accessed through ranges in I/O or memory space. While most
modern devices allow relocation of such ranges, some "Legacy" VGA devices
implemented on PCI will typically have the same "hard-decoded" addresses as
they did on ISA. For more details see "PCI Bus Binding to IEEE Std 1275-1994
Standard for Boot (Initialization Configuration) Firmware Revision 2.1"
Section 7, Legacy Devices.
The Resource Access Control (RAC) module inside the X server currently does
the task of arbitration when more than one legacy device co-exists on the same
machine. But the problem happens when these devices are trying to be accessed
by different userspace clients (e.g. two server in parallel). Their address
assignments conflict. Therefore an arbitration scheme _outside_ of the X
server is needed to control the sharing of these resources. This document
introduces the operation of the VGA arbiter implemented for Linux kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup based on the prototype from Matthew Milcox.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move it from the middle of the function to the end.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Unify msi_free_irqs() and msix_free_all_irqs(), and rename it to a
common void function free_msi_irqs().
And relocate the common function to where the prototype is located now.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The msi_list never have MSI-X's msi_desc while MSI is enabled,
and also it never have MSI's msi_desc while MSI-X is enabled.
This patch remove check for MSI-X entry from the pci_disable_msi(),
referring that pci_disable_msix() does not have any check for MSI
entry.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We already print it out for pci bridges, so also print it out for pci devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
http://bugzilla.kernel.org/show_bug.cgi?id=12542 reports that with the
quirk not applied on resume, msi stops working after resuming and mcp78s
ahci fails due to IRQ mis-delivery. Apply it on resume too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Tj <linux@tjworld.net>
Reported-by: Nicolas Derive <kalon33@ubuntu.com>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Shut off the long standing
linux/drivers/pci/search.c:144: warning: 'pci_find_device' is deprecated (declared at linux/drivers/pci/search.c:136)
linux/drivers/pci/search.c:144: warning: 'pci_find_device' is deprecated (declared at linux/drivers/pci/search.c:136)
warnings that appear on every build when CONFIG_PCI_LEGACY is enabled.
gcc warns for the use in EXPORT_SYMBOL
I moved these to a separate file and disabled the warning in the Makefile for that file.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One more form factor for Compaq Evo D510, which needs the same quirk
as the other form factors. Apparently there's no hardware monitoring
chip on that one, but SPD EEPROMs, so it's still worth unhiding the
SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Nuzhna Pomoshch <nuzhna_pomoshch@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some devices allow an individual function to be reset without affecting
other functions in the same device: that's what pci_reset_function does.
For devices that have this support, expose reset attribite in sysfs.
This is useful e.g. for virtualization, where a qemu userspace
process wants to reset the device when the guest is reset,
to emulate machine reboot as closely as possible.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We cannot simply call acpi_get_pci_dev() on any random ACPI handle
and hope that it works, because a PCI root bridge may not have
an associated struct pci_dev.
This is allowed per the PCI specification, and is referred to as a
non-materialized bridge.
So, depending on the type of PCI bridge that the handle points to,
use the appropriate interface to return the struct pci_bus correctly.
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
yenta needs this for example.
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This was #define'd as 0 on all platforms, so let's get rid of it.
This change makes pci_scan_slot() slightly easier to read.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Conflicts:
arch/x86/kernel/reboot.c
security/Kconfig
Merge reason: resolve the conflicts, bump up from rc3 to rc8.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move tboot.h from asm to linux to fix the build errors of intel_txt
patch on non-X86 platforms. Remove the tboot code from generic code
init/main.c and kernel/cpu.c.
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This file needs to include linux/dmi.h directly rather than relying on
it being pulled in from elsewhere.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
DMAR faults are recorded into a ring of "fault recording registers".
fault_index is a 0-based index into the ring. The code allows the
0-based fault_index to be equal to the total number of fault registers
available from the cap_num_fault_regs() macro, which causes access
beyond the last available register.
Signed-off-by Troy Heber <troy.heber@hp.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
An SR-IOV capable device includes an SR-IOV PCIe capability which
describes the Virtual Function (VF) BAR requirements. A typical SR-IOV
device can support multiple VFs whose BARs must be in a contiguous region,
effectively an array of VF BARs. The BAR reports the size requirement
for a single VF. We calculate the full range needed by simply multiplying
the VF BAR size with the number of possible VFs and create a resource
spanning the full range.
This all seems sane enough except it artificially inflates the alignment
requirement for the VF BAR. The VF BAR need only be aligned to the size
of a single BAR not the contiguous range of VF BARs. This can cause us
to fail to allocate resources for the BAR despite the fact that we
actually have enough space.
This patch adds a thin PCI specific layer over the generic
resource_alignment() function which is aware of the special nature of
VF BARs and does sorting and allocation based on the smaller alignment
requirement.
I recognize that while resource_alignment is generic, it's basically a
PCI helper. An alternative to this patch is to add PCI VF BAR specific
information to struct resource. I opted for the extra layer rather than
adding such PCI specific information to struct resource. This does
have the slight downside that we don't cache the BAR size and re-read
for each alignment query (happens a small handful of times during boot
for each VF BAR).
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
make it use the node from irq_desc.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A95C392.5050903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
Generic support for remapping HPET MSI's by parsing the HPET timer block
device scope in the ACPI DRHD tables. This is needed for platforms
supporting interrupt-remapping and MSI capable HPET timer block.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Jay Fenlason <fenlason@redhat.com>
LKML-Reference: <20090804190729.477649000@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The kcalloc() failure path in iommu_init_domains() calls
free_dmar_iommu(), which assumes that ->domains, ->domain_ids,
and ->lock have been properly initialized.
Add checks in free_[dmar]_iommu to not use ->domains,->domain_ids
if not alloced. Move the lock init to prior to the kcalloc()'s,
so it is valid in free_context_table() when free_dmar_iommu() invokes
it at the end.
Patch based on iommu-2.6,
commit 132032274a
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mark si_domain_init and iommu_prepare_static_identity_mapping with
__init, to eliminate the following warnings:
WARNING: drivers/pci/built-in.o(.text+0xf1f4): Section mismatch in reference from the function si_domain_init() to the function .init.text:si_domain_work_fn()
The function si_domain_init() references
the function __init si_domain_work_fn().
This is often because si_domain_init lacks a __init
annotation or the annotation of si_domain_work_fn is wrong.
WARNING: drivers/pci/built-in.o(.text+0xe340): Section mismatch in reference from the function iommu_prepare_static_identity_mapping() to the function .init.text:si_domain_init()
The function iommu_prepare_static_identity_mapping() references
the function __init si_domain_init().
This is often because iommu_prepare_static_identity_mapping lacks a __init
annotation or the annotation of si_domain_init is wrong.
Signed-off-by: Matt Kraai <kraai@ftbfs.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.
Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: SGI hotplug: do not use hotplug_slot_attr
PCI hotplug: SGI hotplug: fix build failure
All callers of the former were also calling the latter, in one order or
the other, and failing to correctly clean up if the second returned
failure.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
By the pci slot changes, callbacks of attributes under slot directory
(/sys/bus/pci/slots) had been changed to get the pointer to struct
pci_slot instead of struct hotplug_slot. So the path_show() that
assumes the parameter is a pointer to struct hotplug_slot seems
broken.
Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The commit bd3d99c170 ("PCI: Remove
untested Electromechanical Interlock (EMI) support in pciehp."), which
removes the definition of "struct hotplug_slot_attr", broke SGI
hotplug driver. By this commit, we get the following compile error.
drivers/pci/hotplug/sgi_hotplug.c:106: error: variable 'sn_slot_path_attr' has initializer but incomplete type
drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'attr' specified in initializer
drivers/pci/hotplug/sgi_hotplug.c:106: error: extra brace group at end of initializer
drivers/pci/hotplug/sgi_hotplug.c:106: error: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c:106: error: unknown field 'show' specified in initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: excess elements in struct initializer
drivers/pci/hotplug/sgi_hotplug.c:106: warning: (near initialization for 'sn_slot_path_attr')
drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hp_destroy':
drivers/pci/hotplug/sgi_hotplug.c:203: error: invalid use of undefined type 'struct hotplug_slot_attribute'
drivers/pci/hotplug/sgi_hotplug.c: In function 'sn_hotplug_slot_register':
drivers/pci/hotplug/sgi_hotplug.c:655: error: invalid use of undefined type 'struct hotplug_slot_attribute'
This patch fixes this regression by adding the definition of struct
hotplug_slot_attr into sgi_hotplug.c.
Tested-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Two defects work together result in KVM device passthrough randomly can't
work:
1. iommu_snooping is not initialized to zero when vm_iommu_init() called.
So it is possible to get a random value.
2. One line added by commit 2c2e2c38("IOMMU Identity Mapping Support")
change the code path, let it bypass domain_update_iommu_cap(), as well as
missing the increment of domain iommu reference count.
The latter is also likely to cause a leak of domains on repeated VMM
assignment and deassignment.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The physical address passed to domain_pfn_mapping() should be rounded
down to the start of the MM page, not the VT-d page.
This issue causes kernel panic on PAGE_SIZE>VTD_PAGE_SIZE platforms e.g. ia64
platforms.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In domain_sg_mapping(), use aligned_nrpages() instead of hand-coded
rounding code for calculating the size of each sg elem. This means that
on IA64 we correctly round up to the MM page size, not just to the VT-d
page size.
Also remove the incorrect mm_to_dma_pfn() when intel_map_sg() calls
domain_sg_mapping() -- the 'size' variable is in VT-d pages already.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This makes the hardware passthrough mode work a lot more like the
software version, so that the behaviour of a kernel with 'iommu=pt'
is the same whether the hardware supports passthrough or not.
In particular:
- We use a single si_domain for the pass-through devices.
- 32-bit devices can be taken out of the pass-through domain so that
they don't have to use swiotlb.
- Devices will work again after being removed from a KVM guest.
- A potential oops on OOM (in init_context_pass_through()) is fixed.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Yet another reason why trusting this stuff to the BIOS was a bad idea.
The HP DC7900 BIOS reports an iommu at an address which just returns all
ones, when VT-d is disabled in the BIOS.
Fix up the missing iounmap in the error paths while we're at it.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This function has traditionally used "insert_resource()", because before
commit cebd78a8c5 ("Fix pci_claim_resource") it used to just insert the
resource into whatever root resource tree that was indicated by
"pcibios_select_root()".
So there Matthew fixed it to actually look up the proper parent
resource, which means that now it's actively wrong to then traverse the
resource tree any more: we already know exactly where the new resource
should go.
And when we then did commit a76117dfd6 ("x86: Use pci_claim_resource"),
which changed the x86 PCI code from the open-coded
pr = pci_find_parent_resource(dev, r);
if (!pr || request_resource(pr, r) < 0) {
to using
if (pci_claim_resource(dev, idx) < 0) {
that "insert_resource()" now suddenly became a problem, and causes a
regression covered by
http://bugzilla.kernel.org/show_bug.cgi?id=13891
which this fixes.
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Linux PCI <linux-pci@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They are not supposed to be modified by drivers, so make them const.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The tboot module will DMA protect all of memory in order to ensure the that
kernel will be able to initialize without compromise (from DMA). Consequently,
the kernel must enable Intel Virtualization Technology for Directed I/O
(VT-d or Intel IOMMU) in order to replace this broad protection with the
appropriate page-granular protection. Otherwise DMA devices will be unable
to read or write from memory and the kernel will eventually panic.
Because runtime IOMMU support is configurable by command line options, this
patch will force it to be enabled regardless of the options specified, and will
log a message if it was required to force it on.
dmar.c | 7 +++++++
intel-iommu.c | 17 +++++++++++++++--
2 files changed, 22 insertions(+), 2 deletions(-)
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: Shane Wang <shane.wang@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
g_iommus is freed after we "goto error;".
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We only ever obtain this lock immediately before the iova_rbtree_lock,
and release it immediately after the iova_rbtree_lock. So ditch it and
just use iova_rbtree_lock.
[v2: Remove the lockdep bits this time too]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After some API change, intel_iommu_unmap_range() introduced a assumption that
parameter size != 0, otherwise the dma_pte_clean_range() would have a
overflowed argument. But the user like KVM don't have this assumption before,
then some BUG() triggered.
Fix it by ignoring size = 0.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We did before, in the end -- but it was at the bottom of a long stack of
functions. Add an inline wrapper get_valid_domain_for_dev() which will
use the cached one _first_ and only make the out-of-line call if it's
not already set.
This takes the average time taken for a 1-page intel_map_sg() from 5961
cycles to 4812 cycles on my Lenovo x200s test box -- a modest 20%.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Fix IRQ swizzling for ARI-enabled devices
ia64/PCI: adjust section annotation for pcibios_setup()
x86/PCI: get root CRS before scanning children
x86/PCI: fix boundary checking when using root CRS
PCI MSI: Fix restoration of MSI/MSI-X mask states in suspend/resume
PCI MSI: Unmask MSI if setup failed
PCI MSI: shorten PCI_MSIX_ENTRY_* symbol names
PCI: make pci_name() take const argument
PCI: More PATA quirks for not entering D3
PCI: fix kernel-doc warnings
PCI: check if bus has a proper bridge device before triggering SBR
PCI: remove pci_dac_dma_... APIs on mn10300
PCI ECRC: Remove unnecessary semicolons
PCI MSI: Return if alloc_msi_entry for MSI-X failed
Our current strategy for pass-through mode is to put all devices into
the 1:1 domain at startup (which is before we know what their dma_mask
will be), and only _later_ take them out of that domain, if it turns out
that they really can't address all of memory.
However, when there are a bunch of PCI devices behind a bridge, they all
end up with the same source-id on their DMA transactions, and hence in
the same IOMMU domain. This means that we _can't_ easily move them from
the 1:1 domain into their own domain at runtime, because there might be DMA
in-flight from their siblings.
So we have to adjust our pass-through strategy: For PCI devices not on
the root bus, and for the bridges which will take responsibility for
their transactions, we have to start up _out_ of the 1:1 domain, just in
case.
This fixes the BUG() we see when we have 32-bit-capable devices behind a
PCI-PCI bridge, and use the software identity mapping.
It does mean that we might end up using 'normal' mapping mode for some
devices which could actually live with the faster 1:1 mapping -- but
this is only for PCI devices behind bridges, which presumably aren't the
devices for which people are most concerned about performance.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
At boot time, the dma_mask won't have been set on any devices, so we
assume that all devices will be 64-bit capable (and thus get a 1:1 map).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This should fix kernel.org bug #11821, where the dcdbas driver makes up
a platform device and then uses dma_alloc_coherent() on it, in an
attempt to get memory < 4GiB.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We need to give people a little more time to fix the broken drivers.
Re-introduce this, but tied in properly with the 'iommu=pt' support this
time. Change the config option name and make it default to 'no' too.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do this twice, and it's about to get more complicated. This makes the
code slightly clearer about what it's doing, too.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When we reattach a device to the si_domain (because it's been removed
from a VM), we weren't calling domain_context_mapping() to actually tell
the hardware about that.
We should really put the call to domain_context_mapping() into
domain_add_dev_info() -- we never call the latter without also doing the
former, and we can keep the error paths simple that way. But that's a
cleanup which can wait for 2.6.32 now.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We should check iommu_dummy() _first_, because that means it's attached
to an iommu that we've just disabled completely. At the moment, we might
try to put the device into the identity mapping domain.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The aligned_nrpages() function rounds up to the next VM page, but
returns its result as a number of DMA pages.
Purely theoretical except on IA64, which doesn't boot with VT-d right
now anyway.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/iommu-2.6: (38 commits)
intel-iommu: Don't keep freeing page zero in dma_pte_free_pagetable()
intel-iommu: Introduce first_pte_in_page() to simplify PTE-setting loops
intel-iommu: Use cmpxchg64_local() for setting PTEs
intel-iommu: Warn about unmatched unmap requests
intel-iommu: Kill superfluous mapping_lock
intel-iommu: Ensure that PTE writes are 64-bit atomic, even on i386
intel-iommu: Make iommu=pt work on i386 too
intel-iommu: Performance improvement for dma_pte_free_pagetable()
intel-iommu: Don't free too much in dma_pte_free_pagetable()
intel-iommu: dump mappings but don't die on pte already set
intel-iommu: Combine domain_pfn_mapping() and domain_sg_mapping()
intel-iommu: Introduce domain_sg_mapping() to speed up intel_map_sg()
intel-iommu: Simplify __intel_alloc_iova()
intel-iommu: Performance improvement for domain_pfn_mapping()
intel-iommu: Performance improvement for dma_pte_clear_range()
intel-iommu: Clean up iommu_domain_identity_map()
intel-iommu: Remove last use of PHYSICAL_PAGE_MASK, for reserving PCI BARs
intel-iommu: Make iommu_flush_iotlb_psi() take pfn as argument
intel-iommu: Change aligned_size() to aligned_nrpages()
intel-iommu: Clean up intel_map_sg(), remove domain_page_mapping()
...
Check dma_pte_present() and only free the page if there _is_ one.
Kind of surprising that there was no warning about this.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On Wed, 2009-07-01 at 16:59 -0700, Linus Torvalds wrote:
> I also _really_ hate how you do
>
> (unsigned long)pte >> VTD_PAGE_SHIFT ==
> (unsigned long)first_pte >> VTD_PAGE_SHIFT
Kill this, in favour of just looking to see if the incremented pte
pointer has 'wrapped' onto the next page. Which means we have to check
it _after_ incrementing it, not before.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For many purposes, including interrupt-swizzling, devices with ARI
enabled behave as if they have one device (number 0) and 256 functions.
This probably hasn't bitten us in practice because all ARI devices I've
seen are also IOV devices, and IOV devices are required to use MSI.
This isn't guaranteed, and there are legitimate reasons to use ARI
without IOV, and hence potentially use pin-based interrupts.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This would have found the bug in i386 pci_unmap_addr() a long time ago.
We shouldn't just silently return without doing anything.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since we're using cmpxchg64() anyway (because that's the only way to do
an atomic 64-bit store on i386), we might as well ditch the extra
locking and just use cmpxchg64() to ensure that we don't add the page
twice.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes kernel.org bug #13584. The IOVA code attempted to optimise
the insertion of new ranges into the rbtree, with the unfortunate result
that some ranges just didn't get inserted into the tree at all. Then
those ranges would be handed out more than once, and things kind of go
downhill from there.
Introduced after 2.6.25 by ddf02886cb
("PCI: iova RB tree setup tweak").
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: mark gross <mgross@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As with other functions, batch the CPU data cache flushes and don't keep
recalculating PTE addresses.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The loop condition was wrong -- we should free a PMD only if its
_entire_ range is within the range we're intending to clear. The
early-termination condition was right, but not the loop.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of calling domain_pfn_mapping() repeatedly with single or
small numbers of pages, just pass the sglist in. It can optimise the
number of cache flushes like domain_pfn_mapping() does, and gives a huge
speedup for large scatterlists.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are 2 problems on mask states in suspend/resume.
[1]:
It is better to restore the mask states of MSI/MSI-X to initial states
(MSI is unmasked, MSI-X is masked) when we release the device.
The pci_msi_shutdown() does the restoration of mask states for MSI,
while the msi_free_irqs() does it for MSI-X. In other words, in the
"disable" path both of MSI and MSI-X are handled, but in the "shutdown"
path only MSI is handled.
MSI:
pci_disable_msi()
=> pci_msi_shutdown()
[ mask states for MSI restored ]
=> msi_set_enable(dev, pos, 0);
=> msi_free_irqs()
MSI-X:
pci_disable_msix()
=> pci_msix_shutdown()
=> msix_set_enable(dev, 0);
=> msix_free_all_irqs
=> msi_free_irqs()
[ mask states for MSI-X restored ]
This patch moves the masking for MSI-X from msi_free_irqs() to
pci_msix_shutdown().
This change has some positive side effects:
- It prevents OS from touching mask states before reading preserved
bits in the register, which can be happen if msi_free_irqs() is
called from error path in msix_capability_init().
- It also prevents touching the register after turning off MSI-X in
"disable" path, which can be a problem on some devices.
[2]:
We have cache of the mask state in msi_desc, which is automatically
updated when msi/msix_mask_irq() is called. This cached states are
used for the resume.
But since what need to be restored in the resume is the states before
the shutdown on the suspend, calling msi/msix_mask_irq() from
pci_msi/msix_shutdown() is not appropriate.
This patch introduces __msi/msix_mask_irq() that do mask as same
as msi/msix_mask_irq() but does not update cached state, for use
in pci_msi/msix_shutdown().
[updated: get rid of msi/msix_mask_irq_nocache() (proposed by Matthew Wilcox)]
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The initial state of mask register of MSI is unmasked. We set it
masked before calling arch_setup_msi_irqs(). If arch_setup_msi_irq()
fails, it is better to restore the state of the mask register.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These names are too long! Drop _OFFSET to save some bytes/lines.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ALi loses some state if it goes into D3. Unfortunately even with the
chipset documents I can't figure out how to restore some bits of it.
The VIA one saves/restores apparently fine but the ACPI _GTM methods break
on some platforms if we do this and this causes cable misdetections.
These are both effectively regressions as historically nothing matched the
devices and then decided not to bind to them. Nowdays something is binding
to all sorts of devices and a result they get dumped into D3.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For devices attached to the root bus, we can't trigger Secondary Bus
Reset because there is no bridge device associated with the bus. So
need to check bus->self again NULL first before using it.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In current code it continues setup even if alloc_msi_entry() for MSI-X
is failed due to lack of memory. It means arch_setup_msi_irqs() might
be called with msi_desc entries less than its argument nvec.
At least x86's arch_setup_msi_irqs() uses list_for_each_entry() for
dev->msi_list that suspected to have entries same numbers as nvec, and
it doesn't check the number of allocated vectors and passed arg nvec.
Therefore it will result in success of pci_enable_msix(), with less
vectors allocated than requested.
This patch fixes the error route to return -ENOMEM, instead of continuing
the setup (proposed by Matthew Wilcox).
Note that there is no iounmap in msi_free_irqs() if no msi_disc is
allocated.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There's no need for the separate iommu_alloc_iova() function, and
certainly not for it to be global. Remove the underscores while we're at
it.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As with dma_pte_clear_range(), don't keep flushing a single PTE at a
time. And also micro-optimise the setting of PTE values rather than
using the helper functions to do all the masking.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It's a bit silly to repeatedly call domain_flush_cache() for each PTE
individually, as we clear it. Instead, batch them up and flush a whole
range at a time. We might as well refrain from recalculating the PTE
address from scratch each time round the loop too.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is fairly broken anyway -- it doesn't take hotplug into account.
We should probably be checking page_is_ram() instead.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Most of its callers are having to shift for themselves anyway, so we might
as well do it in iommu_flush_iotlb_psi().
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
... and use it in the trivial cases; the other callers want individual
(and bisectable) attention, since I screwed them up the first time...
Make the BUG_ON() happen on too-large virtual address rather than
physical address, too. That's the one we care about.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use unaligned address for domain->max_addr. That algorithm isn't ideal
anyway -- we should probably just look at the last iova in the tree.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With some cleanup of intel_unmap_page(), intel_unmap_sg() and
vm_domain_exit() to no longer play with 64-bit addresses.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add some helpers for converting between VT-d and normal system pfns,
since system pages can be larger than VT-d pages.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There's no need for the GFX workaround now we have 'iommu=pt' for the
cases where people really care about performance. There's no need to
have a special case for just one type of device.
This also speeds up the iommu=pt path and reduces memory usage by
setting up the si_domain _once_ and then using it for all devices,
rather than giving each device its own private page tables.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In caching mode, domain ID 0 is reserved for non-present to present
mapping flush. Device IOTLB doesn't need to be flushed in this case.
Previously we were avoiding the flush for domain zero, even if the IOMMU
wasn't in caching mode and domain zero wasn't special.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Drop the e820 scanning and use existing function for finding valid
RAM regions to add to 1:1 mapping.
Signed-off-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (72 commits)
asus-laptop: remove EXPERIMENTAL dependency
asus-laptop: use pr_fmt and pr_<level>
eeepc-laptop: cpufv updates
eeepc-laptop: sync eeepc-laptop with asus_acpi
asus_acpi: Deprecate in favor of asus-laptop
acpi4asus: update MAINTAINER and KConfig links
asus-laptop: platform dev as parent for led and backlight
eeepc-laptop: enable camera by default
ACPI: Rename ACPI processor device bus ID
acerhdf: Acer Aspire One fan control
ACPI: video: DMI workaround broken Acer 7720 BIOS enabling display brightness
ACPI: run ACPI device hot removal in kacpi_hotplug_wq
ACPI: Add the reference count to avoid unloading ACPI video bus twice
ACPI: DMI to disable Vista compatibility on some Sony laptops
ACPI: fix a deadlock in hotplug case
Show the physical device node of backlight class device.
ACPI: pdc init related memory leak with physical CPU hotplug
ACPI: pci_root: remove unused dev/fn information
ACPI: pci_root: simplify list traversals
ACPI: pci_root: use driver data rather than list lookup
...
To support domain-isolation usages, the platform hardware must be
capable of uniquely identifying the requestor (source-id) for each
interrupt message. Without source-id checking for interrupt remapping
, a rouge guest/VM with assigned devices can launch interrupt attacks
to bring down anothe guest/VM or the VMM itself.
This patch adds source-id checking for interrupt remapping, and then
really isolates interrupts for guests/VMs with assigned devices.
Because PCI subsystem is not initialized yet when set up IOAPIC
entries, use read_pci_config_byte to access PCI config space directly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Interrupt remapping table entry is 128bits. Currently, it only sets low
64bits of irte in modify_irte and free_irte. This ignores high 64bits
setting of irte, that means source-id setting will be ignored. This patch
sets the whole 128bits of irte when modify/free it. Following source-id
checking patch depends on this.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Identity mapping for IOMMU defines a single domain to 1:1 map all PCI
devices to all usable memory.
This reduces map/unmap overhead in DMA API's and improve IOMMU
performance. On 10Gb network cards, Netperf shows no performance
degradation compared to non-IOMMU performance.
This method may lose some of DMA remapping benefits like isolation.
The patch sets up identity mapping for all PCI devices to all usable
memory. In the DMA API, there is no overhead to maintain page tables,
invalidate iotlb, flush cache etc.
32 bit DMA devices don't use identity mapping domain, in order to access
memory beyond 4GiB.
When kernel option iommu=pt, pass through is first tried. If pass
through succeeds, IOMMU goes to pass through. If pass through is not
supported in hw or fail for whatever reason, IOMMU goes to identity
mapping.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/~dwmw2/iommu-2.6.31:
intel-iommu: Fix one last ia64 build problem in Pass Through Support
VT-d: support the device IOTLB
VT-d: cleanup iommu_flush_iotlb_psi and flush_unmaps
VT-d: add device IOTLB invalidation support
VT-d: parse ATSR in DMA Remapping Reporting Structure
PCI: handle Virtual Function ATS enabling
PCI: support the ATS capability
intel-iommu: dmar_set_interrupt return error value
intel-iommu: Tidy up iommu->gcmd handling
intel-iommu: Fix tiny theoretical race in write-buffer flush.
intel-iommu: Clean up handling of "caching mode" vs. IOTLB flushing.
intel-iommu: Clean up handling of "caching mode" vs. context flushing.
VT-d: fix invalid domain id for KVM context flush
Fix !CONFIG_DMAR build failure introduced by Intel IOMMU Pass Through Support
Intel IOMMU Pass Through Support
Fix up trivial conflicts in drivers/pci/{intel-iommu.c,intr_remapping.c}
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
Use msix_mask_irq() instead of direct use of writel, so as not to clear
preserved bits in the Vector Control register [31:1].
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The previous MSI-X fix (8d18101853) had
three bugs. First, it didn't move the write that disabled the vector.
This led to writing garbage to the MSI-X vector (spotted by Michael
Ellerman). It didn't fix the PCI resume case, and it had a race window
where the device could generate an interrupt before the MSI-X registers
were programmed (leading to a DMA to random addresses).
Fortunately, the MSI-X capability has a bit to mask all the vectors.
By setting this bit instead of clearing the enable bit, we can ensure
the device will not generate spurious interrupts. Since the capability
is now enabled, the NIU device will not have a problem with the reads
and writes to the MSI-X registers being in the original order in the code.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
By having a pointer to the root port link, we can remove loops in
get_root_port_link() to search the root port link.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We don't need the 'has_switch' field in the struct pcie_link_state.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup for calc_L0S_latency() and calc_L1_latency().
- Separate exit latency and acceptable latency calculation.
- Some minor cleanups.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current ASPM implementation, callers of pcie_set_clock_pm() check
Clock PM capability of the link or current Clock PM state of the link.
This check should be done in pcie_set_clock_pm() itself.
This patch moves those checks into pcie_set_clock_pm(). It also
introduces pcie_set_clkpm_nocheck() that is equivalent to old
pcie_set_clock_pm(), for the caller who wants to change Clocl PM state
regardless of the Clock PM capability or current Clock PM state. In
addition, this patch changes the function name from
pcie_set_clock_pm() to pcie_set_clkpm() for consistency.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up ASPM initialization by refactoring some functionality, renaming
functions, and moving things around.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the current ASPM implementation, there are many functions that
take a pointer to struct pci_dev corresponding to the upstream component
of the link as a parameter. But, since those functions handle PCI
express link state, a pointer to struct pcie_link_state is more
suitable than a pointer to struct pci_dev. Changing a parameter to a
pointer to struct pcie_link_state makes ASPM code much simpler and
easier to read. This patch also contains some minor cleanups. This patch
doesn't have any functional change.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cleanup for some fields in pcie_link_state.
- Add comments.
- make "downstream_has_switch" field 1-bit.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The "clk_pm_capable", "clk_pm_enable" and "bios_clk_state" fields in
the struct pcie_link_state only take 1-bit value. So those fields
don't need to be defined as unsigned int. This patch makes those
fields 1-bit, and cleans up some related code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up latency related data structures for ASPM.
- Introduce struct acpi_latency for exit latency and acceptable
latency management. With this change, struct endpoint_state is no
longer needed.
- We don't need to hold both upstream latency and downstream latency
in the current implementation.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The "support_state", "enabled_state" and "bios_aspm_state" fields in
the struct pcie_link_state take 2-bit value. So those fields don't
need to be defined as unsigned int. This patch makes those fields
2-bit, and cleans up some related code.
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
