Different ColdFire CPUs have different ways of defining where their
internal peripheral registers sit in their address space. Some use an
MBAR register, some use and IPSBAR register, some have a fixed mapping.
Now that most of the peripheral address definitions have been cleaned up
we can clean up the setting of the MBAR and IPSBAR defines to limit them
to just where they are needed (and where they actually exist).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
In some of the RAM size autodetection code on ColdFire CPU startup
we reference DRAM registers relative to the MBAR register. Not all of
the supported ColdFire CPUs have an MBAR, and currently this works
because we fake an MBAR address on those registers. In an effort to
clean this up, and eventually remove the fake MBAR setting make the
DRAM register address definitions actually contain the MBAR (or IPSBAR
as appropriate) value as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Not all ColdFire CPUs that use the old style timer hardware module use
an MBAR set peripheral region. Move the TIMER base address defines to the
per-CPU header files where we can set it correctly based on how the
peripherals are mapped - instead of using a fake MBAR for some platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The base addresses of the ColdFire DMA unit registers belong with
all the other address definitions in the per-cpu headers. The current
definitions assume they are relative to an MBAR register. Not all
ColdFire CPUs have an MBAR register. A clean address define can only
be acheived in the per-cpu headers along with all the other chips
peripheral base addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 528x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 527x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 523x family of CPUs does not have an MBAR register, so don't
define its peripheral addresses relative to one. Its internal peripherals
are relative to the IPSBAR register, so make sure to use that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 5207 and 5208 CPUs have fixed peripheral addresses.
They do not use the setable peripheral address registers like the MBAR
and IPSBAR used on many other ColdFire parts. Don't use fake values
of MBAR and IPSBAR when using peripheral addresses for them, there
is no need to.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The PIT hardware timer module used in some ColdFire CPU's is not always
addressed relative to an IPSBAR register. Parts like the ColdFire 5207 and
5208 have fixed peripheral addresses. So lets not define the register
addresses of the PIT relative to an IPSBAR definition. Move the base
address definitions into the per-part headers. This is a lot more consistent
since all the other peripheral base addresses are defined in the per-part
header files already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Remove the bogus definition of the MBAR register for the ColdFire 532x
family. It doesn't have an MBAR register, its peripheral registers are
at fixed addresses and are not relative to a settable base.
All the code that relyed on this definition existing has been cleaned
up. The register address definitions now include the base as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 54xx family shares the same interrupt controller used
on the 523x, 527x and 528x ColdFire parts, but it isn't offset
relative to the IPSBAR register. The 54xx doesn't have an IPSBAR
register.
By including the base address of the peripheral registers in the register
definitions (MCFICM_INTC0 and MCFICM_INTC1 in this case) we can avoid
having to define a fake IPSBAR for the 54xx. And this makes the register
address definitions of these more consistent, the majority of the other
register address defines include the peripheral base address already.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MBAR2 register is only used on the ColdFire 5249 part, so move its
definition out of the common coldfire.h and into the 5249 support header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add an m68k/coldfire optimized memmove() function for the m68knommu arch.
This is the same function as used by m68k. Simple speed tests show this
is faster once buffers are larger than 4 bytes, and significantly faster
on much larger buffers (4 times faster above about 100 bytes).
This also goes part of the way to fixing a regression caused by commit
ea61bc461d ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memmove() fucntion
defined, since there was none in the m68knommu/lib functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The m68k arch implements its own memcmp() function. It is not optimized
in any way (it is the most strait forward coding of memcmp you can get).
Remove it and use the kernels standard memcmp() implementation.
This also goes part of the way to fixing a regression caused by commit
ea61bc461d ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memcmp() function
defined, since there is none in the m68knommu/lib functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
It's a way too generic name for a global #define and conflicts with a variable
with the same name, causing build errors like:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c: In function ‘_si_clkctl_cc’:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected identifier or ‘(’ before ‘volatile’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected ‘)’ before ‘(’ token
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1421: error: incompatible types in assignment
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1422: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1423: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1424: error: invalid operands to binary |
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: incompatible type for argument 4 of ‘bcmsdh_reg_write’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1428: error: invalid operands to binary &
| make[8]: *** [drivers/staging/brcm80211/brcmfmac/../util/siutils.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Some versions of gcc replace calls to strstr() with single-character
"needle" string parameters by calls to strchr() behind our back.
If strchr() is defined as an inline function, this causes linking errors
like
ERROR: "strchr" [drivers/target/target_core_mod.ko] undefined!
As m68k is the only architecture that has an inline strchr() and this
inline version is not an optimized asm version, uninline strchr() and use
the standard out-of-line C version in lib/string.c instead.
This also decreases the defconfig/allmodconfig kernel image sizes by a few
hundred bytes.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (25 commits)
m68knommu: fix broken setting of irq_chip and handler
m68knommu: switch to using -mcpu= flags for ColdFire targets
m68knommu: arch/m68knommu/Kconfig whitespace cleanup
m68knommu: create optimal separate instruction and data cache for ColdFire
m68knommu: support ColdFire caches that do copyback and write-through
m68knommu: support version 2 ColdFire split cache
m68knommu: make cache push code ColdFire generic
m68knommu: clean up ColdFire cache control code
m68knommu: move inclusion of ColdFire v4 cache registers
m68knommu: merge bit definitions for version 3 ColdFire cache controller
m68knommu: create bit definitions for the version 2 ColdFire cache controller
m68knommu: remove empty __iounmap() it is no used
m68knommu: remove kernel_map() code, it is not used
m68knommu: remove do_page_fault(), it is not used
m68knommu: use user stack pointer hardware on some ColdFire cores
m68knommu: remove command line printing DEBUG
m68knommu: remove fasthandler interrupt code
m68knommu: move UART addressing to part specific includes
m68knommu: fix clock rate value reported for ColdFire 54xx parts
m68knommu: move ColdFire CPU names into their headers
...
and saner do_signal() arguments, while we are at it
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Since commit 31c911329e ("mm: check the argument
of kunmap on architectures without highmem"), we get lots of warnings like
arch/m68k/kernel/sys_m68k.c:508: warning: passing argument 1 of ‘kunmap’ from incompatible pointer type
As m68k doesn't support highmem anyway, open code the calls to kmap() and
kunmap() (the latter is a no-op) to kill the warnings, like is done on most
other architectures without CONFIG_HIGHPTE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sam Creasey <sammy@sammy.net>
Create separate functions to deal with instruction and data cache flushing.
This way we can optimize them for the vairous cache types and arrangements
used across the ColdFire family.
For example the unified caches in the version 3 cores means we don't
need to flush the instruction cache. For the version 2 cores that do
not do data cacheing (or where we choose instruction cache only) we
don't need to do any data flushing.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The version 3 and version 4 ColdFire cache controllers support both
write-through and copy-back modes on the data cache. Allow for Kconfig
time configuration of this, and set the cache mode appropriately.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The newer version 2 ColdFire CPU cores support a configurable cache
arrangement. The cache memory can be used as all instruction cache, all
data cache, or split in half for both instruction and data caching.
Support this setup via a Kconfig time menu that allows a kernel builder
to choose the arrangement they want to use.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently the code to push cache lines is only available to version 4
cores. Version 3 cores may also need to use this if we support copy-
back caches on them. Move this code to make it more generic, and
useful for all version ColdFire cores.
With this in place we can now have a single cache_flush_all() code
path that does all the right things on all version cores.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The cache control code for the ColdFire CPU's is a big ugly mess
of "#ifdef"ery liberally coated with bit constants. Clean it up.
The cache controllers in the various ColdFire parts are actually quite
similar. Just differing in some bit flags and options supported. Using
the header defines now in place it is pretty easy to factor out the
small differences and use common setup and flush/invalidate code.
I have preserved the cache setups as they where in the old code
(except where obviously wrong - like in the case of the 5249). Following
from this it should be easy now to extend the possible setups used on
the CACHE controllers that support split cacheing or copy-back or
write through options.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Move the inclusion of the version 4 cache controller registers so that
it is with all the other register bit flag definitions. This makes it
consistent with the other version core inclusion points, and means we
don't need "#ifdef"ery in odd-ball places for these definitions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All version 3 based ColdFire CPU cores have a similar cache controller.
Merge all the exitsing definitions into a single file, and make them
similar in style and naming to the existing version 2 and version 4
cache controller definitions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The version 2 ColdFire CPU based cores all contain a similar cache
controller unit. Create a set of bit flag definitions for the supporting
registers.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The more modern ColdFire parts (even if based on older version cores)
have separate user and supervisor stack pointers (a7 register).
Modify the ColdFire CPU setup and exception code to enable and use
this on parts that have it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire UART base addresses varies between the different ColdFire
family members. Instead of keeping the base addresses with the UART
definitions keep them with the other addresses definitions for each
ColdFire part.
The motivation for this move is so that when we add new ColdFire
part definitions, they are all in a single file (and we shouldn't
normally need to modify the UART definitions in mcfuart.h at all).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The instruction timings of the ColdFire 54xx family parts are
different to other version 4 parts (or version 2 or 3 parts for
that matter too).
Move the instruction timing setting into the ColdFire part
specific headers, and set the 54xx value appropriately.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Move the ColdFire CPU names out of setup.c and into their repsective
headers. That way when we add new ones we won't need to modify
setup.c any more.
Add the missing 548x CPU name.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 547x family of processors is very similar to the ColdFire
548x series. Almost all of the support for them is the same. Make the
code supporting the 548x more gneric, so it will be capable of
supporting both families.
For the most part this is a renaming excerise to make the support
code more obviously apply to both families.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Now that we have meaningfull symbolic constants for bit definitions
of the cache registers of m5407 and m548x chips, use them to
improve readability, portability and efficiency of the cache operations.
This also fixes __flush_cache_all for m548x chips : implicit
DCACHE_SIZE was exact for m5407, but wrong for m548x.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
__flush_cache_all for m54xx is intrinsically related to the bit
definitions in m54xxacr.h. Move it there from cacheflush_no.h,
for easier maintenance.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MCF548x have the same cache control registers as the MCF5407.
Extract the bit definitions for the ACR and CACR registers from m5407sim.h
and move them to a new file m54xxacr.h. Those definitions are not used
anywhere yet, so no other file is involved. This is a preparation for
m54xx cache support cleanup.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Recent changes to header files made kernel compilation for m68k/m68knommu
fail with :
CC arch/m68knommu/kernel/asm-offsets.s
In file included from /archives/linux/git/arch/m68k/include/asm/system.h:2,
from include/linux/wait.h:25,
from include/linux/mmzone.h:9,
from include/linux/gfp.h:4,
from include/linux/irq.h:20,
from include/asm-generic/hardirq.h:12,
from /archives/linux/git/arch/m68k/include/asm/hardirq_no.h:17,
from /archives/linux/git/arch/m68k/include/asm/hardirq.h:2,
from include/linux/hardirq.h:10,
from /archives/linux/git/arch/m68k/include/asm/irqflags.h:5,
from include/linux/irqflags.h:15,
from include/linux/spinlock.h:53,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:56,
from arch/m68knommu/kernel/asm-offsets.c:12:
/archives/linux/git/arch/m68k/include/asm/system_no.h: In function ‘__xchg’:
/archives/linux/git/arch/m68k/include/asm/system_no.h:79: error: implicit
+declaration of function ‘local_irq_save’
/archives/linux/git/arch/m68k/include/asm/system_no.h:101: error: implicit
+declaration of function ‘local_irq_restore’
Fix that
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The cleanup and merge of machdep should not have removed the do_IRQ
declaration. It is needed by the 68328 based targets.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Long ago, PT_TRACESYS_OFF and friends were introduced as hard defines to
avoid straight constants in assembler parts of linux m68k. They are not
used anymore, and were not updated to follow changes in linux kernel.
Remove them. When similar constants are needed, they are now generated
using asm-offsets.c.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we no longer need to provide KM_type, the whole pte_*map_nested()
API is now redundant, remove it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
m68knommu: convert to using tracehook_report_syscall_*
m68knommu: some boards use fixed phy for FEC ethernet
m68knommu: support the external GPIO based interrupts of the 5272
m68knommu: mask of vector bits in exception word properly
m68knommu: change to new flag variables
m68knommu: Fix MCFUART_TXFIFOSIZE for m548x.
m68knommu: add basic mmu-less m548x support
m68knommu: .gitignore vmlinux.lds
m68knommu: stop using __do_IRQ
m68knommu: rename PT_OFF_VECTOR to PT_OFF_FORMATVEC.
m68knommu: add support for Coldfire 547x/548x interrupt controller
m68k{nommu}: Remove unused DEFINE's from asm-offsets.c
m68knommu: whitespace cleanup in 68328/entry.S
m68knommu: Document supported chips in intc-2.c and intc-simr.c.
m68knommu: fix strace support for 68328/68360
m68knommu: fix default starting date
arch/m68knommu: Removing dead 68328_SERIAL_UART2 config option
arch/m68knommu: Removing dead RAM_{16,32}_MB config option
arch/m68knommu: Removing dead M68KFPU_EMU config option
arch/m68knommu: Removing dead RELOCATE config option
...
On m68k, I/O macros like inb() outw() etc. are only defined to
something useful if CONFIG_ISA is set; dummies are in place if
not, but four macros were missing from the !CONFIG_ISA case.
Adding these makes some drivers, such as speakup, compile again.
Signed-off-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes this:
drivers/char/mem.c: In function 'mmap_kmem':
drivers/char/mem.c:342: warning: cast to pointer from integer of different size
by doing what other archtiectures do.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The MMU and non-MMU versions of traps.h are virtually identical,
merge them into a single file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The MMU and non-MMU versions of thread_info.h are quite similar.
Merge the two files.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The only difference between the MMU and non-MMU versions of atomic.h
is some extra support needed by ColdFire family processors. So merge
this into the MMU version of atomic.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There is a lot of common defines in the MMU and non-MMU variants of
page.h. Factor out the common stuff into the master page.h. It still
includes the underlying page_mm.h or page_no.h, but they only contain
the real differences now.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
No need to have separate machdep.h files for each of the MMU and non-MMU
cases. Merge them all into a single file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The MMU and non-MMU string.h varients (string_no.h and string_mm.h)
and almost the same. Switch to using the string_mm.h one, merging
in the necessary ColdFire support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
CONFIG_SMP doesn't exist in Kconfig (for this architecure), therefore
remove all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move the definition of THREAD_SIZE from page_mm.h to thread_info_mm.h
This logically associates it with the other thread definitions, and will
make it easier to merge the MMU and non-MMU versions of page.h and
thread_info.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch converts m68k to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- m68k defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds TIOCSRS485 and TIOCGRS485m which are unused
by any driver available on this architecture.
- The generic version adds support for termiox
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
CONFIG_GG2 doesn't exist in Kconfig, therefore remove
all references to it from the source.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Serial lines on the MCF548x have really big fifos : 512 bytes.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add a very basic mmu-less support for coldfire m548x family. This is perhaps
also valid for m547x family. The port comprises the serial, tick timer and
reboot support. The gpio part compiles but is empty. This gives a functional
albeit limited linux for the m548x coldfire family. This has been tested
on a Freescale M548xEVB Lite board with a M5484 processor and the default
dbug monitor.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
The arch/m68k/include/asm/ide.h produces errors when the IDE driver is compiled for my 523x uClinux system under kernel. The header makes some redefines of operators not defined in the arch/m68k/include/asm/io_no.h header. There are no separate mmio and iospace defines.
Signed-off-by: Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now each architecture has the own dma_get_cache_alignment implementation.
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
define it as ARCH_KMALLOC_MINALIGN (it's used to make sure that malloc'ed
buffer is DMA-safe; the buffer doesn't share a cache with the others). So
we can unify dma_get_cache_alignment implementations.
This patch:
dma_get_cache_alignment() needs to know if an architecture defines
ARCH_KMALLOC_MINALIGN or not (needs to know if architecture has DMA
alignment restriction). However, slab.h define ARCH_KMALLOC_MINALIGN if
architectures doesn't define it.
Let's rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN.
ARCH_KMALLOC_MINALIGN is used only in the internals of slab/slob/slub
(except for crypto).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
This patch is against the 2.6.34 source.
Paraphrased from the 1989 BSD patch by David Borman @ cray.com:
These are the changes needed for the kernel to support
LINEMODE in the server.
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
New ioctl:
TIOCSIG Generate a signal to processes in the
current process group of the pty.
There is a new mode for packet driver, the TIOCPKT_IOCTL bit.
When packet mode is turned on in the pty, and the EXTPROC bit
is set, then whenever the state of the pty is changed, the
next read on the master side of the pty will have the TIOCPKT_IOCTL
bit set. This allows the process on the server side of the pty
to know when the state of the terminal has changed; it can then
issue the appropriate ioctl to retrieve the new state.
Since the original BSD patches accompanied the source code for telnet
I've left that reference here, but obviously the feature is useful for
any remote terminal protocol, including ssh.
The corresponding feature has existed in the BSD tty driver since 1989.
For historical reference, a good copy of the relevant files can be found
here:
http://anonsvn.mit.edu/viewvc/krb5/trunk/src/appl/telnet/?pathrev=17741
Signed-off-by: Howard Chu <hyc@symas.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removal of these started in 2.3.43pre3, ca. 10 years ago.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 64bit, local_t is of size long, and thus we make local64_t an alias.
On 32bit, we fall back to atomic64_t. (architecture can provide optimized
32-bit version)
(This new facility is to be used by perf events optimizations.)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-arch@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
arch/m68knommu/platform/68360/commproc.c: Checkpatch cleanup
arch/m68knommu/mm/fault.c: Checkpatch cleanup
m68knommu: improve short help of m68knommu/Kconfig/RAMSIZE for '0' case
m68knommu: remove un-used mcfsmc.h
m68knommu: add smc91x support for ColdFire NETtel boards
m68knommu: add smc91x support to ColdFire 5249 platform
m68knommu: remove size limit on non-MMU TASK_SIZE
m68knommu: fix broken use of BUAD_TABLE_SIZE in 68328serial driver
m68knommu: Coldfire QSPI platform support
Remove the un-used mcfsmc.h. All ColdFire platforms that use SMC ethernet
devices are platform enabled to use the smc91x driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The TASK_SIZE define is used in some places as a limit on the size of
the virtual address space of a process. On non-MMU systems those addresses
used in comparison will be physical addresses, and they could be anywhere
in the 32bit physical address space. So for !CONFIG_MMU systems set the
TASK_SIZE to the maximum physical address.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
linux-next:
fs/udf/balloc.c: In function 'udf_bitmap_new_block':
fs/udf/balloc.c:274: error: implicit declaration of function 'generic_find_next_le_bit'
Convert ext2_find_next_{zero_,}bit() into generic_find_next_{zero_,}le_bit(),
and wrap the ext2_find_next_{zero_,}bit() around the latter.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
In preparation for removing volatile from the atomic_t definition, this
patch adds a volatile cast to all the atomic read functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since Grant has added the coldfire-qspi driver to next-spi, here is the
platform support for the parts that have qspi hardware. This sets up
gpio to do the spi chip select using the default chip select pins; it should
be trivial for boards that require different or additional spi chip selects to
use other gpios as needed.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix tcdrain on coldfire uarts.
Currently with coldfire uarts tcdrain returns without waiting for txempty,
because (tx)fifosize is 0. Fix that and call uart_update_timeout when
setting the baud rate, otherwise tcdrain will wait for an half our :)
Also constify mcf_uart_ops.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Recently, we started seeing this on allmodconfig builds:
CC mm/memcontrol.o
{standard input}: Assembler messages:
{standard input}:4076: Error: operands mismatch -- statement `subl 12(%fp),170(%a0)' ignored
Correct the asm constraint, like done for m68knommu.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
LibSegFault uses piggybacks sc_fpstate field of the `struct sigcontext'
and this patch avoids LibSegFault overflowing this field. Also this
removes an unnecessary divergence from classic m68k.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
While in theory user_enable_single_step/user_disable_single_step/
user_enable_blockstep could also be provided as an inline or macro there's
no good reason to do so, and having the prototype in one places keeps code
size and confusion down.
Roland said:
The original thought there was that user_enable_single_step() et al
might well be only an instruction or three on a sane machine (as if we
have any of those!), and since there is only one call site inlining
would be beneficial. But I agree that there is no strong reason to care
about inlining it.
As to the arch changes, there is only one thought I'd add to the
record. It was always my thinking that for an arch where
PTRACE_SINGLESTEP does text-modifying breakpoint insertion,
user_enable_single_step() should not be provided. That is,
arch_has_single_step()=>true means that there is an arch facility with
"pure" semantics that does not have any unexpected side effects.
Inserting a breakpoint might do very unexpected strange things in
multi-threaded situations. Aside from that, it is a peculiar side
effect that user_{enable,disable}_single_step() should cause COW
de-sharing of text pages and so forth. For PTRACE_SINGLESTEP, all these
peculiarities are the status quo ante for that arch, so having
arch_ptrace() itself do those is one thing. But for building other
things in the future, it is nicer to have a uniform "pure" semantics
that arch-independent code can expect.
OTOH, all such arch issues are really up to the arch maintainer. As
of today, there is nothing but ptrace using user_enable_single_step() et
al so it's a distinction without a practical difference. If/when there
are other facilities that use user_enable_single_step() and might care,
the affected arch's can revisit the question when someone cares about
the quality of the arch support for said new facility.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the ipc demultiplexer syscall. Except for
s390 and sparc64 all implementations of the sys_ipc are nearly identical.
There are slight differences in the types of the parameters, where mips
and powerpc as the only 64-bit architectures with sys_ipc use unsigned
long for the "third" argument as it gets casted to a pointer later, while
it traditionally is an "int" like most other paramters. frv goes even
further and uses unsigned long for all parameters execept for "ptr" which
is a pointer type everywhere. The change from int to unsigned long for
"third" and back to "int" for the others on frv should be fine due to the
in-register calling conventions for syscalls (we already had a similar
issue with the generic sys_ptrace), but I'd prefer to have the arch
maintainers looks over this in details.
Except for that h8300, m68k and m68knommu lack an impplementation of the
semtimedop sub call which this patch adds, and various architectures have
gets used - at least on i386 it seems superflous as the compat code on
x86-64 and ia64 doesn't even bother to implement it.
[akpm@linux-foundation.org: add sys_ipc to sys_ni.c]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the old mmap() syscall, which expects its
argument in a memory block and switch all architectures over to use it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the old select() syscall, which expects
its argument in a memory block and switch all architectures over to use
it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Acked-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch defines sigcontext ABI of ColdFire. Due to ISA
restrictions ColdFire needs different rt_sigreturn trampoline.
And due to ColdFire FP registers being 8-bytes instead of 12-bytes on
m68k, sigcontext and fpregset structures should be updated.
Regarding the sc_fpstate[16+6*8] field, it would've been enough 16
bytes to store ColdFire's FP state. To accomodate GLIBC's libSegFault
it would'be been enough 6*8 bytes (room for the 6 non-call-clobbered
FP registers). I set it to 16+6*8 to provide some extra space for any
future changes in the ColdFire FPU.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Port syscalls for NPTL support to m68knommu.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch adds several syscalls, that provide necessary
functionality to support NPTL on m68k/ColdFire.
The syscalls are get_thread_area, set_thread_area, atomic_cmpxchg_32 and
atomic_barrier.
The cmpxchg syscall is required for ColdFire as it doesn't support 'cas'
instruction.
Also a ptrace call PTRACE_GET_THREAD_AREA is added to allow debugger to
inspect the TLS storage.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch switches m68k to generic siginfo layout. The custom layout
of m68k's `struct siginfo' had several issues due to not considering
aliasing of members in the union, e.g., _uid32 was at different offsets
in ._kill, ._rt and ._sigchld.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove the old 68k Mac serial port code and a lot of related cruft. Add
new SCC platform devices to mac 68k platform.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
