Remove now unused IRQ demux code. All R-Mobile and
SH-Mobile processors should register IRQ demux
handlers during run-time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break-out GIC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.
Covers sh73a0.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break-out INTC specific IRQ demux code from the file
entry-macro-intc.S and register during run-time.
Covers sh7367, sh7377 and sh7372.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the R-Mobile / SH-Mobile processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When CONFIG_ZBOOT_ROM is selected, the resulting zImage file will be small
boot loader and may be burned to rom or flash.
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (416 commits)
ARM: DMA: add support for DMA debugging
ARM: PL011: add DMA burst threshold support for ST variants
ARM: PL011: Add support for transmit DMA
ARM: PL011: Ensure IRQs are disabled in UART interrupt handler
ARM: PL011: Separate hardware FIFO size from TTY FIFO size
ARM: PL011: Allow better handling of vendor data
ARM: PL011: Ensure error flags are clear at startup
ARM: PL011: include revision number in boot-time port printk
ARM: vexpress: add sched_clock() for Versatile Express
ARM i.MX53: Make MX53 EVK bootable
ARM i.MX53: Some bug fix about MX53 MSL code
ARM: 6607/1: sa1100: Update platform device registration
ARM: 6606/1: sa1100: Fix platform device registration
ARM i.MX51: rename IPU irqs
ARM i.MX51: Add ipu clock support
ARM: imx/mx27_3ds: Add PMIC support
ARM: DMA: Replace page_to_dma()/dma_to_page() with pfn_to_dma()/dma_to_pfn()
mx51: fix usb clock support
MX51: Add support for usb host 2
arch/arm/plat-mxc/ehci.c: fix errors/typos
...
fsib_clk will be used when fdiv_clk failed on fsi_hdmi_set_rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Prepare the ap4evb board for the MIPI DSI driver transition to support
different register layouts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now, that the MIPI DSI driver implements runtime PM, we don't need anymore to
configure clocks statically in the platform code. This patch also adds a DSITX1
clock definition for sh7372 and attaches PHY clocks to respective devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh73a0 has divisor[12] setting as 1/7 on FRQCRA.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add VGA camera support to the Mackerel board
using soc_camera_platform.
The VGA camera module is hooked up using the
8-bit CEU bus, and it is constantly bursting
out frames in fixed video mode setting. The
camera module does not allow any I2C control.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Follow up to pfc-sh73a0.c's pull-up support.
Change GPIO_FN_KEYINx to GPIO_FN_KEYINx_PU.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On SH-Mobile, Pull UP/Downs can be controlled independently
from Function selectors (by lower nibble of PFCR).
It means people may want to use GPIO_FN_xxx_PU/PD in addition
to GPIO_IN_PU/PD which is currently supported.
This patch adds pull-up version for some input signals on
KEYSC, MMC, FSIA as well as SDHI1.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the sh73a0 KEYSC clock control by adding MSTP403
to mstp_clks[]. Use KEYSC instead of KEYSC0 in comments.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for 2 TMU timer channels on sh73a0.
One timer channel is used for clocksource and
the other is used for clockevents. All channels
in the same TMU block share MSTP bit as usual.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add INTCS support for the sh73a0 processor.
The interrupts on the sh73a0 processor are managed
through controllers such as GIC, INTCS and INTCA.
The ARM cores use the GIC as primary interrupt
controller and the INTCS and INTCA are hanging off
the GIC as cascaded interrupt controllers.
Peripherals connected both to the GIC and the INTC
controllers should if possible only use the GIC.
If no GIC connection is available then INTCS and
INTCA may be used instead.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Increase NR_IRQS from 512 to 1024 on SH-Mobile ARM.
Needed to support vectors in the sh73a0 INTCS block.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use PAGE_OFFSET and PHYS_OFFSET for secondary_startup
entry point as recommended by Russell King.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix interrupt priority level handling on SH-Mobile ARM.
SH-Mobile ARM platforms using multiple interrupt priority
levels need this patch to fix a potential dead lock that
may occur if multiple interrupts with different levels
are pending simultaneously.
The default INTC configuration is to use the same priority
level for all interrupts, so this issue does not trigger by
default. It is however common for board code to override the
interrupt priority for certain interrupt sources depending
on the application. Without this fix such boards may lock up.
In detail, this patch updates the INTC code in entry-macro.S
to make sure that the INTLVLA register gets set as expected.
To trigger this bug modify the board specific code to adjust
the interrupt priority level for the ethernet chip. After
changing the priority level simply use flood ping to drown
the board with interrupts.
This patch applies to INTCA-based processors such as sh7372,
sh7377 and sh7372. GIC-based processors are not affected.
Suitable for v2.6.37-rc and stable from v2.6.34 to v2.6.36.
Cc: stable@kernel.org
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Turn down the warning noise from the compiler,
basically a SH-Mobile specific version of the
patch located in the RMK patch tracker:
6484/1: "fix compile warning in mm/init.c",
Without this patch the following warning triggers:
CC arch/arm/kernel/sys_arm.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
CC arch/arm/kernel/traps.o
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SMP support for ag5evm and the sh73a0 processor.
Onlining and offlining works well, but at this point
offlined processor cores are not put into sleep mode.
There is no spinlock for syncing the secondary core
with the first one in this implementation. The code
instead relies on the cpu_online() check in __cpu_up().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SMP base support for R-Mobile / SH-Mobile processors.
This patch contains all base code to support CONFIG_SMP
regardless of ARCH_SHMOBILE processor type. Both local timer
and CPU hotplug are supported, but no processor specific
code is included.
At this point only the default behavior is in place, so
a single core will always be used even though CONFIG_SMP
is enabled on multicore systems.
The SMP Kconfig entry for arch/arm/Kconfig is excluded from
this patch to simplify merging.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Compiling in multiple CPUs into the same kernel binary
requires a Makefile update. With this patch in place
it is possible to enable the pinmux code for both the
SH7372 and the SH7377.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch maps key0/key1/key2/key3 as HOME/MENU/BACK/POWER buttons
on mackerel board.
Signed-off-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When CONFIG_ZBOOT_ROM is selected, the resulting zImage file will be small
boot loader and may be burned to rom or flash.
This is the board-specific portion of this patch-set.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_ZBOOT_ROM is selected, the resulting zImage file will be small
boot loader and may be burned to rom or flash.
This is the non-board-specific framework portion of this patch-set.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch improves the state of the AG5 clock
framework support. The main clock parent is
automatically detected, but most of the clocks
are not used by any driver or subsystem at this
point. More work is needed for support of multi
media hardware such as FSI and/or LCDC/MIPI-DSI.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
