Fixed the asix_get_wol() routine reported wrong wol status issue.
Signed-off-by: Allan Chou <allan@asix.com.tw>
Tested-by: Eugene <elubarsky@gmail.com>; Allan Chou <allan@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just fixed typo of sample code in packet_mmap.txt
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- Add debugfs support to obtain firmware trace, saved firmware trace on
an IOC crash, driver info and read/write to registers.
- debugfs hierarchy:
bna/pci_dev:<pci_name>
where the pci_name corresponds to the one under /sys/bus/pci/drivers/bna
- Following are the new debugfs entries added:
fwtrc: collect current firmware trace.
fwsave: collect last saved fw trace as a result of firmware crash.
regwr: write one word to chip register
regrd: read one or more words from chip register.
drvinfo: collect the driver information.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change details:
- The patch adds flash sub-module to the bna driver.
- Added ethtool set_eeprom() and get_eeprom() entry points to
support flash partition read/write operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warning raised
when compile:
WARNING: modpost: missing MODULE_LICENSE()
in drivers/net/ethernet/stmicro/stmmac/stmmac.o
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes incorrect address storage while storing
Long Term Key for LE Devices using SMP (Security Manager Protocol).
The address stored should be of remote device and not of source device.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Broken in commit d1dc698a54
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use raw_spin_unlock_irqrestore() as equivalent to
raw_spin_lock_irqsave().
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1324646665-13334-1-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"! --connbytes 23:42" should match if the packet/byte count is not in range.
As there is no explict "invert match" toggle in the match structure,
userspace swaps the from and to arguments
(i.e., as if "--connbytes 42:23" were given).
However, "what <= 23 && what >= 42" will always be false.
Change things so we use "||" in case "from" is larger than "to".
This change may look like it breaks backwards compatibility when "to" is 0.
However, older iptables binaries will refuse "connbytes 42:0",
and current releases treat it to mean "! --connbytes 0:42",
so we should be fine.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The NAT range to nlattr conversation callbacks and helpers are entirely
dead code and are also useless since there are no NAT ranges in conntrack
context, they are only used for initially selecting a tuple. The final NAT
information is contained in the selected tuples of the conntrack entry.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The packet size check originates from a time when UDP helpers could
accidentally mangle incorrect packets (NEWNAT) and is unnecessary
nowadays since the conntrack helpers invoke the NAT helpers for the
proper packet directly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The inner tuple that is extracted from the packet is unused. The code also
doesn't have any useful side-effects like verifying the packet does contain
enough data to extract the inner tuple since conntrack already does the
same, so remove it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The only remaining user of NAT protocol module reference counting is NAT
ctnetlink support. Since this is a fairly short sequence of code, convert
over to use RCU and remove module reference counting.
Module unregistration is already protected by RCU using synchronize_rcu(),
so no further changes are necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use nf_conntrack_hash_rnd in NAT bysource hash to avoid hash chain attacks.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Export the NAT definitions to userspace. So far userspace (specifically,
iptables) has been copying the headers files from include/net. Also
rename some structures and definitions in preparation for IPv6 NAT.
Since these have never been officially exported, this doesn't affect
existing userspace code.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This partially reworks bc01befdcf
which added userspace expectation support.
This patch removes the nf_ct_userspace_expect_list since now we
force to use the new iptables CT target feature to add the helper
extension for conntracks that have attached expectations from
userspace.
A new version of the proof-of-concept code to implement userspace
helpers from userspace is available at:
http://people.netfilter.org/pablo/userspace-conntrack-helpers/nf-ftp-helper-POC.tar.bz2
This patch also modifies the CT target to allow to set the
conntrack's userspace helper status flags. This flag is used
to tell the conntrack system to explicitly allocate the helper
extension.
This helper extension is useful to link the userspace expectations
with the master conntrack that is being tracked from one userspace
helper.
This feature fixes a problem in the current approach of the
userspace helper support. Basically, if the master conntrack that
has got a userspace expectation vanishes, the expectations point to
one invalid memory address. Thus, triggering an oops in the
expectation deletion event path.
I decided not to add a new revision of the CT target because
I only needed to add a new flag for it. I'll document in this
issue in the iptables manpage. I have also changed the return
value from EINVAL to EOPNOTSUPP if one flag not supported is
specified. Thus, in the future adding new features that only
require a new flag can be added without a new revision.
There is no official code using this in userspace (apart from
the proof-of-concept) that uses this infrastructure but there
will be some by beginning 2012.
Reported-by: Sam Roberts <vieuxtech@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This closes races where btrfs is calling d_instantiate too soon during
inode creation. All of the callers of btrfs_add_nondir are updated to
instantiate after the inode is fully setup in memory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Dan Carpenter noticed that we were doing a double unlock on the worker
lock, and sometimes picking a worker thread without the lock held.
This fixes both errors.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
This change fixes a linking problem, which happens if oprofile
is selected to be compiled as built-in:
`oprofile_arch_exit' referenced in section `.init.text' of
arch/arm/oprofile/built-in.o: defined in discarded section
`.exit.text' of arch/arm/oprofile/built-in.o
The problem is appeared after commit 87121ca504, which
introduced oprofile_arch_exit() calls from __init function. Note
that the aforementioned commit has been backported to stable
branches, and the problem is known to be reproduced at least
with 3.0.13 and 3.1.5 kernels.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: oprofile-list <oprofile-list@lists.sourceforge.net>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20111222151540.GB16765@erda.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make sure that mutex is released upon register writing failure.
This fixes boot freezing observed on ARM based OLPC
(http://dev.laptop.org/ticket/11357).
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
skb->truesize might be big even for a small packet.
Its even bigger after commit 87fb4b7b53 (net: more accurate skb
truesize) and big MTU.
We should allow queueing at least one packet per receiver, even with a
low RCVBUF setting.
Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes it to yield sooner at halfway instead. Still not a cure-all
for listener overrun if listner is slow, but works much reliably.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't inline functions that cover several lines, and do inline
the trivial ones. Also make some arguments const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e5671dfae5.
After a follow up discussion with Michal, it was agreed it would
be better to leave the kmem controller with just the tcp files,
deferring the behavior of the other general memory.kmem.* files
for a later time, when more caches are controlled. This is because
generic kmem files are not used by tcp accounting and it is
not clear how other slab caches would fit into the scheme.
We are reverting the original commit so we can track the reference.
Part of the patch is kept, because it was used by the later tcp
code. Conflicts are shown in the bottom. init/Kconfig is removed from
the revert entirely.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
CC: Kirill A. Shutemov <kirill@shutemov.name>
CC: Paul Menage <paul@paulmenage.org>
CC: Greg Thelen <gthelen@google.com>
CC: Johannes Weiner <jweiner@redhat.com>
CC: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/cgroups/memory.txt
mm/memcontrol.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a large rps_flow_cnt like (1 << 30) on 32-bit platform will
cause a kernel oops due to insufficient bounds checking.
if (count > 1<<30) {
/* Enforce a limit to prevent overflow */
return -EINVAL;
}
count = roundup_pow_of_two(count);
table = vmalloc(RPS_DEV_FLOW_TABLE_SIZE(count));
Note that the macro RPS_DEV_FLOW_TABLE_SIZE(count) is defined as:
... + (count * sizeof(struct rps_dev_flow))
where sizeof(struct rps_dev_flow) is 8. (1 << 30) * 8 will overflow
32 bits.
This patch replaces the magic number (1 << 30) with a symbolic bound.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userspace may not provide TCA_OPTIONS, in fact tc currently does
so not do so if no arguments are specified on the command line.
Return EINVAL instead of panicing.
Signed-off-by: Thomas Graf <tgraf@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 618f9bc74a (net: Move mtu handling down to the protocol
depended handlers) forgot the bridge netfilter case, adding a NULL
dereference in ip_fragment().
Reported-by: Chris Boot <bootc@bootc.net>
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://neil.brown.name/md:
md/bitmap: It is OK to clear bits during recovery.
md: don't give up looking for spares on first failure-to-add
md/raid5: ensure correct assessment of drives during degraded reshape.
md/linear: fix hot-add of devices to linear arrays.
commit d0a4bb4927 introduced a
regression which is annoying but fairly harmless.
When writing to an array that is undergoing recovery (a spare
in being integrated into the array), writing to the array will
set bits in the bitmap, but they will not be cleared when the
write completes.
For bits covering areas that have not been recovered yet this is not a
problem as the recovery will clear the bits. However bits set in
already-recovered region will stay set and never be cleared.
This doesn't risk data integrity. The only negatives are:
- next time there is a crash, more resyncing than necessary will
be done.
- the bitmap doesn't look clean, which is confusing.
While an array is recovering we don't want to update the
'events_cleared' setting in the bitmap but we do still want to clear
bits that have very recently been set - providing they were written to
the recovering device.
So split those two needs - which previously both depended on 'success'
and always clear the bit of the write went to all devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Before performing a recovery we try to remove any spares that
might not be working, then add any that might have become relevant.
Currently we abort on the first spare that cannot be added.
This is a false optimisation.
It is conceivable that - depending on rules in the personality - a
subsequent spare might be accepted.
Also the loop does other things like count the available spares and
reset the 'recovery_offset' value.
If we abort early these might not happen properly.
So remove the early abort.
In particular if you have an array what is undergoing recovery and
which has extra spares, then the recovery may not restart after as
reboot as the could of 'spares' might end up as zero.
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NeilBrown <neilb@suse.de>
While reshaping a degraded array (as when reshaping a RAID0 by first
converting it to a degraded RAID4) we currently get confused about
which devices are in_sync. In most cases we get it right, but in the
region that is being reshaped we need to treat non-failed devices as
in-sync when we have the data but haven't actually written it out yet.
Reported-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit d70ed2e4fa
broke hot-add to a linear array.
After that commit, metadata if not written to devices until they
have been fully integrated into the array as determined by
saved_raid_disk. That patch arranged to clear that field after
a recovery completed.
However for linear arrays, there is no recovery - the integration is
instantaneous. So we need to explicitly clear the saved_raid_disk
field.
Signed-off-by: NeilBrown <neilb@suse.de>
This silently was working for many years and stopped working on
Niagara-T3 machines.
We need to set the MSIQ to VALID before we can set it's state to IDLE.
On Niagara-T3, setting the state to IDLE first was causing HV_EINVAL
errors. The hypervisor documentation says, rather ambiguously, that
the MSIQ must be "initialized" before one can set the state.
I previously understood this to mean merely that a successful setconf()
operation has been performed on the MSIQ, which we have done at this
point. But it seems to also mean that it has been set VALID too.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Fix usb/isp1760 build on sparc
usb: gadget: epautoconf: do not change number of streams
usb: dwc3: core: fix cached revision on our structure
usb: musb: fix reset issue with full speed device
They don't need to disable interrupts anymore, we only run in process
context now.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RFCOMM needs a proper priority mechanism inside itself and not try to use
l2cap priority to fix its own problem.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Low Energy pairing is performed through the SMP (Security Manager Protocol)
mechanism rather than HCI.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
To achive Man-In-The-Middle (MITM) level security with Low Energy,
we have to enable User Passkey Comparison. This commit modifies the
hard-coded JUST-WORKS pairing mechanism to support query via the MGMT
interface of Passkey comparison and User Confirmation.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Acked-by: Marcel Holtmann<marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The struct hci_proto and all related register/unregister and dispatching
code was removed. HCI core code now call directly the SCO and L2CAP
event functions.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
