This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).
Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only user of WIPHY_FLAG_SUPPORTS_SEPARATE_DEFAULT_KEYS was removed
and consequently, this flag can be removed, too. In addition, a single
capability flag was not enough to indicate this capability clearly since
the device behavior may be different based on which operating mode is
being used.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 uses ieee80211_disable_40mhz_24ghz module
parameter to allow disabling 40MHz operation in the 2.4GHz band.
Move this handling from mac80211 to cfg80211 so that the feature
will be more generic.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, advertise support for mesh authentication.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently run this timer exactly once when
a new mac80211 device is registered, but that
is completely pointless since it will have no
work to do at all. Therefore, remove that and
also simplify some code using the timer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a log message to ieee80211_restart_hw() to highlight
that special codepath in the logs. This helps debugging
bugs in the rarely tested restart code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module parameter ieee80211_disable_40mhz_24ghz
was meant to allow disabling 40 MHz operation in
the 2.4 GHz band by default. However, it is buggy
as implemented because while it advertises to the
AP that the device doesn't support 40 MHz, it will
itself still use 40 MHz configurations.
To fix this, clear the 40 MHz bits from the sband
completely instead of overriding where used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch to optimize scanning on operating channel
accidentally removed the code that would ensure power was
set to maximum for scanning.
This patch re-adds that functionality.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous code set the channel type to NO_HT, but it
appears that NO_HT packets can be sent on any channel
type, so we do not need to change the channel type
as long as the channel is correct.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should decrease un-necessary flushes, on/off channel work,
and channel changes in cases where the only scanned channel is
the current operating channel.
* Removes SCAN_OFF_CHANNEL flag, uses SDATA_STATE_OFFCHANNEL
and is-scanning flags instead.
* Add helper method to determine if we are currently configured
for the operating channel.
* Do no blindly go off/on channel in work.c Instead, only call
appropriate on/off code when we really need to change channels.
Always enable offchannel-ps mode when starting work,
and disable it when we are done.
* Consolidate ieee80211_offchannel_stop_station and
ieee80211_offchannel_stop_beaconing, call it
ieee80211_offchannel_stop_vifs instead.
* Accept non-beacon frames when scanning on operating channel.
* Scan state machine optimized to minimize on/off channel
transitions. Also, when going on-channel, go ahead and
re-enable beaconing. We're going to be there for 200ms,
so seems like some useful beaconing could happen.
Always enable offchannel-ps mode when starting software
scan, and disable it when we are done.
* Grab local->mtx earlier in __ieee80211_scan_completed_finish
so that we are protected when calling hw_config(), etc.
* Pass probe-responses up the stack if scanning on local
channel, so that mlme can take a look.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices don't support the maximum AMDPU buffer size of 64, so we
need to add an option to configure this in the hardware configuration.
This value will be used in the ADDBA response instead of the value
suggested in the request, if the latter is greater than the max
supported.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of the fixes for the
reorder timer, mac80211 will cause lockdep
warnings because lockdep confuses
local->skb_queue and local->rx_skb_queue
and treats their lock as the same.
However, their locks are different, and are
valid in different contexts (the former is
used in IRQ context, the latter in BH only)
and the only thing to be done is mark the
former as a different lock class so that
lockdep can tell the difference.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Sujith <m.sujith@gmail.com>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Sujith <m.sujith@gmail.com>
Tested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to support remain-on-channel
offload if they implement smarter timing or need
to use a device implementation like iwlwifi.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses the issue of serialization between
the main rx path and various reorder release timers.
<http://www.spinics.net/lists/linux-wireless/msg57214.html>
It converts the previously local "frames" queue into
a global rx queue [rx_skb_queue]. This way, everyone
(be it the main rx-path or some reorder release timeout)
can add frames to it.
Only one active rx handler worker [ieee80211_rx_handlers]
is needed. All other threads which have lost the race of
"runnning_rx_handler" can now simply "return", knowing that
the thread who had the "edge" will also take care of their
workload.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The throughput trigger will require doing LED
classdev/trigger handling before register_hw(),
so drivers should have access to the trigger
names before it. If trigger registration fails,
this will still make the trigger name available,
but that's not a big problem since the default
trigger will the simply not be found.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let path selection frames for protocols other than HWMP be sent to
userspace via NL80211_CMD_REGISTER_FRAME. Also allow userspace to send
and receive mesh path selection frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the upcoming hardware offload implementation,
some devices will have a different maximum duration
for the remain-on-channel command. Advertise the
maximum duration in mac80211, and make mac80211 set
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When software crypto is used, mac80211 will
support IBSS RSN, it doesn't depend on the
driver in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for split default keys (unicast
and multicast) in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wrap mesh sections inside CONFIG_MAC80211_MESH to fix compilation
problems reported by Stephen Rothwell, Larry Finger and Bruno Randolf.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 651b52254f added DS Parameter Set
information into Probe Request frames that are transmitted on 2.4 GHz
band, but it failed to increment local->scan_ies_len to cover this new
information. This variable needs to be updated to match the maximum IE
data length so that the extra buffer need gets reduced from the driver
limit.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iee80211_hw->restart_work is the only work which uses the system
workqueue. Instead of calling flush_scheduled_work() during
iee80211_exit(), cancel the work during unregistration.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the frame registration notification, we
can see when probe requests are requested and
notify the low-level driver via filtering. The
flag is also set in AP and IBSS modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is partial revert and fix for commit
85f72bc839 "mac80211: only cancel
software-based scans on suspend"
When cfg80211 request the scan and mac80211 perform some management work,
we defer the scan request. We do not canceling such requests when calling
ieee80211_scan_cancel(), because of SCAN_SW_SCANNING bit check just
before the call. So fix that problem.
Another problem, which commit 85f72bc839
tries to solve, is we can not cancel HW scan. Hence patch make
ieee80211_scan_cancel() ignore HW scan (see code comments). Keeping
local->mtx lock assures that the deferred scan will not become
"working" HW scan.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking around ieee80211_recalc_smps is
buggy -- it cannot acquire another interface's
mutex while the iflist mutex is held because
another code path could be holding the iface
mutex and trying to acquire the iflist mutex.
But the locking is also unnecessary, we only
check "ifmgd->associated" as a bool, and don't
use the pointer (in check_mgd_smps).
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers cannot handle multiple retry rates specified by the rc
algorithm but instead use their own retry table (for example rt2800).
However, if such a device registers itself with a max_rates value of 1
the rc algorithm cannot make use of the extended information the device
can provide about retried rates. On the other hand, if a device
registers itself with a max_rates value > 1 the rc algorithm assumes
that the device can handle multi rate retries.
Fix this issue by introducing another hw parameter max_report_rates that
can be set to a different value then max_rates to indicate if a device
is capable of reporting more rates then specified in max_rates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize the rate table for WDS interfaces, and
add cases to allow WDS packets to pass the xmit and receive
tests.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ieee80211_scan_cancel() and all other related code to
ieee80211_restart_work() as ieee80211_restart_hw() is intended to be
callable from any context.
Fix a bug that RTNL lock is not taken during ieee80211_cancel_scan().
Take local->mtx before WARN(test_bit(SCAN_HW_SCANNING, &local->scanning)
to prevent the race condition with __ieee80211_start_scan() described
here: http://marc.info/?l=linux-wireless&m=128516716810537&w=2
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Association is dealt with as an atomic offchannel operation,
we do this because we don't know we are associated until we
get the associatin response from the AP. When we do get the
associatin response though we were never clearing the offchannel
state. This has a few implications, we told drivers we were
still offchannel, and the first configured TX power for the
channel does not take into account any power constraints.
For ath9k this meant ANI calibration would not start upon
association, and we'd have to wait until the first bgscan
to be triggered. There may be other issues this resolves
but I'm too lazy to comb the code to check.
Cc: stable@kernel.org
Cc: Amod Bodas <amod.bodas@atheros.com>
Cc: Vasanth Thiagarajan <vasanth.thiagarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dev->ip_ptr is protected by rtnl and rcu.
Yet some places dont use appropriate primitives and/or locking rules.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed to avoid warning in ieee80211_restart_hw about hardware
scan in progress.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function exists to clean-up after a hardware error or something
similar. The restart is accomplished using the same infrastructure used
to resume after a suspend. The suspend path cancels running scans, so
it seems appropriate to do that here as well for software-based scans.
If a hardware-based scan is pending, issue a warning message since this
indicates that the drivers has failed to clean-up after itself.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new workqueue changes helped me find this bug
that's been lingering since the changes to the work
processing in mac80211 -- the work timer is never
deleted properly. Do that to avoid having it fire
after all data structures have been freed. It can't
be re-armed because all it will do, if running, is
schedule the work, but that gets flushed later and
won't have anything to do since all work items are
gone by now (by way of interface removal).
Cc: stable@kernel.org [2.6.34+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of ieee80211_sdata_running(),
some new code was introduced that uses netif_running()
instead. Switch all these instances over.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Support this
in mac80211 via the cfg80211 API for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to specify their own set of cipher
suites to advertise vendor-specific ciphers. The
driver is then required to implement hardware
crypto offload for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a mac80211-based driver advertises mesh mode
support, this will be advertised to userspace.
However, if mac80211 was compiled without mesh
support, then that won't actually be true. Fix
this by removing the bit for mesh if mesh isn't
compiled in.
Since this synchronizes what we advertise to
cfg80211 and actually support, it means we can
now rely on cfg80211's interface type checks
and need not check again in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unlike most other workqueue-tasks, the restart_work is
not scheduled onto mac80211's private per-interface
workqueue, but onto one of the system-wide workqueues.
Therefore the mac80211-stack has to cancel any pending
restarts, before destroying the shared device context
and handing back the memory. Otherwise - under very
unlucky circumstances - there could be a stale work-
item left, because some other kernel component might
have delayed the execution of ieee80211_restart_work
for too long.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WEP is unavailable, don't advertise it
to cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having both scan and work mutexes is not just
a bit too fine grained, it also creates issues
when there's code that needs both since they
then need to be acquired in the right order,
which can be hard to do.
Therefore, use just a single mutex for both.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running in client mode and associating to an AP, the channel
change is usually performed with the offchannel flag still set.
However after the assoc is complete, the following channel change event
is suppressed because the run time channel is already set to the operating channel.
Fix this by sending channel change notifications to the driver even if
only the offchannel flag changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implement basic infrastructure to support use of NAPI by
mac80211-based hardware drivers.
Because mac80211 devices can support multiple netdevs, a dummy netdev
is used for interfacing with the NAPI code in the core of the network
stack. That structure is hidden from the hardware drivers, but the
actual napi_struct is exposed in the ieee80211_hw structure so that the
poll routines in drivers can retrieve that structure. Hardware drivers
can also specify their own weight value for NAPI polling.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The warning is:
net/mac80211/main.c:688: warning: label ‘fail_ifa’ defined but not used
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some drivers it can be useful to know whether the channel they're
supposed to switch to is going to be used for short off-channel work or
scanning, or whether the hardware is expected to stay on it for a while
longer. This is important for various kinds of calibration work, which
takes longer to complete and should keep some persistent state, even if
the channel temporarily changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current mac80211 code assumes that WEP is always available. If WEP
fails to initialize, ieee80211_register_hw will always fail.
In some cases (e.g. FIPS certification), the cryptography used by WEP is
unavailable. However, in such cases there is no good reason why CCMP
encryption (or even no link level encryption) cannot be used. So, this
patch removes mac80211's assumption that WEP (and TKIP) will always be
available for use.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ps-qos latency handling is broken. It uses predetermined latency values
to select specific dynamic PS timeouts. With common AP configurations, these
values overlap with beacon interval and are therefore essentially useless
(for network latencies less than the beacon interval, PSM is disabled.)
This patch remedies the problem by replacing the predetermined network latency
values with one high value (1900ms) which is used to go trigger full psm. For
backwards compatibility, the value 2000ms is still mapped to a dynamic ps
timeout of 100ms.
Currently also the mac80211 internal value for storing user space configured
dynamic PSM values is incorrectly in the driver visible ieee80211_conf struct.
Move it to the ieee80211_local struct.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a circular locking dependency when configuring the
hardware ARP filters on association, occurring when flushing the mac80211
workqueue. This is what happens:
[ 92.026800] =======================================================
[ 92.030507] [ INFO: possible circular locking dependency detected ]
[ 92.030507] 2.6.34-04781-g2b2c009 #85
[ 92.030507] -------------------------------------------------------
[ 92.030507] modprobe/5225 is trying to acquire lock:
[ 92.030507] ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8105b5c0>] flush_workq
ueue+0x0/0xb0
[ 92.030507]
[ 92.030507] but task is already holding lock:
[ 92.030507] (rtnl_mutex){+.+.+.}, at: [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507]
[ 92.030507] which lock already depends on the new lock.
[ 92.030507]
[ 92.030507]
[ 92.030507] the existing dependency chain (in reverse order) is:
[ 92.030507]
[ 92.030507] -> #2 (rtnl_mutex){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff81341754>] mutex_lock_nested+0x44/0x300
[ 92.030507] [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507] [<ffffffffa022d47c>] ieee80211_assoc_done+0x6c/0xe0 [mac80211]
[ 92.030507] [<ffffffffa022f2ad>] ieee80211_work_work+0x31d/0x1280 [mac80211]
[ 92.030507] -> #1 ((&local->work_work)){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105a51a>] worker_thread+0x22a/0x370
[ 92.030507] [<ffffffff8105ecc6>] kthread+0x96/0xb0
[ 92.030507] [<ffffffff81003a94>] kernel_thread_helper+0x4/0x10
[ 92.030507]
[ 92.030507] -> #0 ((wiphy_name(local->hw.wiphy))){+.+.+.}:
[ 92.030507] [<ffffffff81075fdc>] __lock_acquire+0x1c0c/0x1d50
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105b60e>] flush_workqueue+0x4e/0xb0
[ 92.030507] [<ffffffffa023ff7b>] ieee80211_stop_device+0x2b/0xb0 [mac80211]
[ 92.030507] [<ffffffffa0231635>] ieee80211_stop+0x3e5/0x680 [mac80211]
The locking in this case is quite complex. Fix the problem by rewriting the
way the hardware ARP filter list is handled - i.e. make a copy of the address
list to the bss_conf struct, and provide that list to the hardware driver
when needed.
The current patch will enable filtering also in promiscuous mode. This may need
to be changed in the future.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently maintains the ampdu_lock to
avoid starting a queue due to one aggregation
session while another aggregation session needs
the queue stopped.
We can do better, however, and instead refcount
the queue stops for this particular purpose,
thus removing the need for the lock. This will
help making ampdu_action able to sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the aggregation callback processing
to the per-sdata skb queue and a work function
rather than the tasklet.
Unfortunately, this means that it extends the
pkt_type hack to that skb queue. However, it
will enable making ampdu_action API changes
gradually, my current plan is to get rid of
this again by forcing drivers to only return
from ampdu_action() when everything is done,
thus removing the callbacks completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a window for ieee80211_ifa_changed() to get called whilst the
managed mode mutex has not been initialized when opening and stopping the
interface. Currently this causes a kernel BUG like the following:
[ 132.460013] kernel BUG at /home/wifi/iwlwifi-2.6/net/mac80211/main.c:380!
[ 132.460013] invalid opcode: 0000 [#1] SMP
The mutex is initialized during open(), hence once netif_running() is true,
the mutex should be valid. Fix by adding a netif_running() check to the
function.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since I recently made station management able
to sleep, I can now rework key management as
well; since it will no longer need a spinlock
and can also use a mutex instead, a bunch of
code to allow drivers' set_key to sleep while
key management is protected by a spinlock can
now be removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware allow extended filtering of ARP frames not intended for
the host. To perform such filtering, the hardware needs to know the current
IP address(es) of the host, bound to its interface.
Add support for ARP filtering to mac80211 by adding a new op to the driver
interface, allowing to configure the current IP addresses. This op is called
upon association with the currently configured address(es), and when
associated whenever the IP address(es) change.
This patch adds configuration of IPv4 addresses only, as IPv6 addresses don't
need ARP filtering.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when one interface switches HT mode,
all others will follow along. This is clearly
undesirable, since the new one might switch to
no-HT while another one is operating in HT.
Address this issue by keeping track of the HT
mode per interface, and allowing only changes
that are compatible, i.e. switching into HT40+
is not possible when another interface is in
HT40-, in that case the second one needs to
fall back to HT20.
Also, to allow drivers to know what's going on,
store the per-interface HT mode (channel type)
in the virtual interface's bss_conf.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IBSS is fixed to a frequency, it can still
scan to try to find the right BSSID. This makes
sense if the BSSID isn't also fixed, but it need
not scan all channels -- just one is sufficient.
Make it do that by moving the scan setup code to
ieee80211_request_internal_scan() and include
a channel variable setting.
Note that this can be further improved to start
the IBSS right away if both frequency and BSSID
are fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Determine the dynamic PS timeout based on the configured ps-qos network
latency. For backwards wext compatibility, allow the dynamic PS timeout
configured by the cfg80211 to overrule the automatically determined value.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance tracing by adding tracing for a variety of
callbacks that the drivers call, and also for
internal calls (currently limited to queue status).
This can aid debugging what is going on in mac80211
in interaction with drivers, since we can now see
what drivers call and not just what mac80211 calls
in the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new RCU lockdep support warns about these
in some contexts -- make it aware of the locks
used to protect all this. Different locks are
used in different contexts which unfortunately
means we can't get perfect checking.
Also remove rcu_dereference() from two places
that don't actually dereference the pointers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix kernel panic by NULL pointer dereference in the context of
ieee80211_ops->prepare_multicast().
This bug was introduced by commit 22bedad3c.. ("net: convert
multicast list to list_head").
Call __hw_addr_init() in ieee80211_alloc_hw() to initialize
list_head of private device multicast list, like we do in
bond_init().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if a driver does not set hw.max_listen_interval a listen
interval of 1 is negotiated with the AP. Thus, the AP could drop
buffered frames for us after just one beacon interval which can
easily happen with the current powersave and scan implementation.
To avoid this issue increase the default interval to 5 which should
be a reasonable safe default.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because it's not yet decided how to configure which queues are U-APSD
enabled, add a debugfs interface for testing purposes.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Unscheduled Automatic Power-Save Delivery (U-APSD) client support. The
idea is that the data frames from the client trigger AP to send the buffered
frames with ACs which have U-APSD enabled. This decreases latency and makes it
possible to save even more power.
Driver needs to use IEEE80211_HW_UAPSD to enable the feature. The current
implementation assumes that firmware takes care of the wakeup and
hardware needing IEEE80211_HW_PS_NULLFUNC_STACK is not yet supported.
Tested with wl1251 on a Nokia N900 and Cisco Aironet 1231G AP and running
various test traffic with ping.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the forgotten linux/wireless.h inclusion from mac80211.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements the new remain-on-channel cfg80211
command in mac80211, extending the work interface.
Also change the work purge code to be able to clean
up events properly (pretending they timed out.)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 offers private data for each BSS struct,
which mac80211 uses. However, mac80211 uses internal
and external (cfg80211) BSS pointers interchangeably
and has a hack to put the cfg80211 bss struct into
the private struct.
Remove this hack, properly converting between the
pointers wherever necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to use auth/assoc for different purposes
other than MLME, it needs to be split up. For other
purposes, a generic work handling (potentially on
another channel) will be useful.
To achieve that, this patch moves much of the MLME
work handling out of mlme into a new work API. The
API can currently handle probing a specific AP,
authentication and association. The MLME previously
handled probe/authentication as one step and will
continue to do so, but they are separate in the new
work handling.
Work items are RCU-managed to be able to check for
existence of an item for a specific frame in the RX
path, but they can be re-used which the MLME right
now will do for its combined probe/auth step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always using netif_running(sdata->dev)
use ieee80211_sdata_running(sdata) now which is
just an inline containing netif_running() for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations it is required that a system be
configured with no support for 40 MHz channels in
the 2.4 GHz band. Rather than imposing any such
restrictions on everybody, allow configuration a
system like that with a module parameter. It is
writable at runtime but only takes effect at the
time of the next association.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable spatial multiplexing in mac80211 by telling the
driver what to do and, where necessary, sending action
frames to the AP to update the requested SMPS mode.
Also includes a trivial implementation for hwsim that
just logs the requested mode.
For now, the userspace interface is in debugfs only,
and let you toggle the requested mode at any time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not all that useful to have the vif/sdata pointer,
we'd rather refer to the interfaces by their name.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For bluetooth 3, we will most likely not have
a netdev for a virtual interface (sdata), so
prepare for that by reducing the reliance on
having a netdev. This patch moves the name
and address fields into the sdata struct and
uses them from there all over. Some work is
needed to keep them sync'ed, but that's not
a lot of work and in slow paths anyway.
In doing so, this also reduces the number of
pointer dereferences in many places, because
of things like sdata->dev->dev_addr becoming
sdata->vif.addr.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a definition of the amount of TX headroom reserved by mac80211 itself
for its own purposes. Also add BUILD_BUG_ON to validate the value.
This define can then be used by drivers to request additional TX headroom
in the most efficient manner.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's enough code to have its own file, I think.
Especially since I'm going to add to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to handle association and authentication in AP mode,
hostapd needs access to the tx status info of its own frames
through a cooked monitor interface. Without this patch the
cooked monitor interfaces also passed on tx status information
for packets from other virtual interfaces. This creates a
significant performance issue on embedded system. Hostapd
tries to work around this by installing a Linux Socket Filter
that only captures the frames it's interested in, however
data duplication and socket filter matching still uses up
enough CPU cycles to be very noticeable on small systems.
This patch ensures that tx status information of non-injected
frames does not make it to cooked monitor interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices require that all frames to a station
are flushed when that station goes into powersave
mode before being able to send frames to that
station again when it wakes up or polls -- all in
order to avoid reordering and too many or too few
frames being sent to the station when it polls.
Normally, this is the case unless the station
goes to sleep and wakes up very quickly again.
But in that case, frames for it may be pending
on the hardware queues, and thus races could
happen in the case of multiple hardware queues
used for QoS/WMM. Normally this isn't a problem,
but with the iwlwifi mechanism we need to make
sure the race doesn't happen.
This makes mac80211 able to cope with the race
with driver help by a new WLAN_STA_PS_DRIVER
per-station flag that can be controlled by the
driver and tells mac80211 whether it can transmit
frames or not. This flag must be set according to
very specific rules outlined in the documentation
for the function that controls it.
When we buffer new frames for the station, we
normally set the TIM bit right away, but while
the driver has blocked transmission to that sta
we need to avoid that as well since we cannot
respond to the station if it wakes up due to the
TIM bit. Once the driver unblocks, we can set
the TIM bit.
Similarly, when the station just wakes up, we
need to wait until all other frames are flushed
before we can transmit frames to that station,
so the same applies here, we need to wait for
the driver to give the OK.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The internal scan request mac80211 uses to
scan for IBSS networks was set up to contain
no channels at all because n_channels wasn't
set after setting up the channels array. Fix
this to properly scan for networks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg