The wrong member was compared in the continguousness check.
Acked-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Use DECLARE_WAIT_QUEUE_HEAD_ONSTACK to make lockdep happy
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Different motherboards have different PNP declarations for
W83781D/W83782D chips. Some declare the whole range of I/O ports (8
ports), some declare only the useful ports (2 ports at offset 5) and
some declare fancy ranges, for example 4 ports at offset 4. To
properly handle all cases, request all ports individually for probing.
After we have determined that we really have a W83781D or W83782D
chip, the useful port range will be requested again, as a single
block.
I did not see a board which needs this yet, but I know of one for lm78
driver and I'd like to keep the logic of these two drivers in sync.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Different motherboards have different PNP declarations for LM78/LM79
chips. Some declare the whole range of I/O ports (8 ports), some
declare only the useful ports (2 ports at offset 5) and some declare
fancy ranges, for example 4 ports at offset 4. To properly handle all
cases, request all ports individually for probing. After we have
determined that we really have an LM78 or LM79 chip, the useful port
range will be requested again, as a single block.
This fixes the driver on the Olivetti M3000 DT 540, at least.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
The #define ADT7462_VOLT_COUNT is wrong, it should be 13 not 12. All the
for loops that use this as a limit count are of the typical form, "for
(n = 0; n < ADT7462_VOLT_COUNT; n++)", so to loop through all voltages
w/o missing the last one it is necessary for the count to be one greater
than it is. (Specifically, you will miss the +1.5V 3GPIO input with count
= 12 vs. 13.)
Signed-off-by: Ray Copeland <ray.copeland@aprius.com>
Acked-by: "Darrick J. Wong" <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
The report descriptor is read by user space (via the Service
Discovery Protocol), so it is only available during the ioctl
to connect. However, the HID probe function that needs the
descriptor might not be called until a specific module is
loaded. Keep a copy of the descriptor so it is available for
later use.
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The functionality bit vector is always returned as a little-endian
32-bit number by the device, so it must be byte-swapped to the host
endianness.
On the other hand, the delay value is handled by the USB stack, so no
byte swapping is needed on our side.
This fixes bug #15105:
http://bugzilla.kernel.org/show_bug.cgi?id=15105
Reported-by: Jens Richter <jens@richter-stutensee.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jens Richter <jens@richter-stutensee.de>
Cc: Till Harbaum <till@harbaum.org>
Cc: stable@kernel.org
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] Call flush_dcache_page after PIO data transfers in libata-sff.c
ahci: add Acer G725 to broken suspend list
libata: fix ata_id_logical_per_physical_sectors
libata-scsi passthru: fix bug which truncated LBA48 return values
The new cs5535-* drivers use PCI header config info rather than MSRs to
determine the memory region to use for things like GPIOs and MFGPTs. As
anticipated, we've run into a buggy BIOS:
[ 0.081818] pci 0000:00:14.0: reg 10: [io 0x6000-0x7fff]
[ 0.081906] pci 0000:00:14.0: reg 14: [io 0x6100-0x61ff]
[ 0.082015] pci 0000:00:14.0: reg 18: [io 0x6200-0x63ff]
[ 0.082917] pci 0000:00:14.2: reg 20: [io 0xe000-0xe00f]
[ 0.083551] pci 0000:00:15.0: reg 10: [mem 0xa0010000-0xa0010fff]
[ 0.084436] pci 0000:00:15.1: reg 10: [mem 0xa0011000-0xa0011fff]
[ 0.088816] PCI: pci_cache_line_size set to 32 bytes
[ 0.088938] pci 0000:00:14.0: address space collision: [io 0x6100-0x61ff] already in use
[ 0.089052] pci 0000:00:14.0: can't reserve [io 0x6100-0x61ff]
This is a Soekris board, and its BIOS sets the size of the PCI ISA bridge
device's BAR0 to 8k. In reality, it should be 8 bytes (BAR0 is used for
SMBus stuff). This quirk checks for an incorrect size, and resets it
accordingly.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Tested-by: Leigh Porter <leigh@leighporter.org>
Tested-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is to make the annotation of percpu variables during the next merge
window less painfull.
Extracted from a patch by Rusty Russell.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: fix r300 vram width calculations
drm/radeon/kms: rs400/480 MC setup is different than r300.
drm/radeon/kms: make initial state of load detect property correct.
drm/radeon/kms: disable HDMI audio for now on rv710/rv730
drm/radeon/kms: don't call suspend path before cleaning up GPU
drivers/gpu/drm/radeon/radeon_combios.c: fix warning
ati_pcigart: fix printk format warning
drm/r100/kms: Emit cache flush to the end of command buffer. (v2)
drm/radeon/kms: fix regression rendering issue on R6XX/R7XX
drm/radeon/kms: move blit initialization after we disabled VGA
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: apply updated fallocate i_size fix
Btrfs: do not try and lookup the file extent when finishing ordered io
Btrfs: Fix oopsen when dropping empty tree.
Btrfs: remove BUG_ON() due to mounting bad filesystem
Btrfs: make error return negative in btrfs_sync_file()
Btrfs: fix race between allocate and release extent buffer.
Pandora's external DAC is using 256*Fs output from the TWL4030
codec, and TWL4030 needs to have APLL enabled for it's 256*Fs
output to function.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is possible (and expected) for there to be holes in the h->drv[]
array, that is, some elements may be NULL pointers. cciss_seq_show
needs to be made aware of this possibility to avoid an Oops.
To reproduce the Oops which this fixes:
1) Create two "arrays" in the Array Configuratino Utility and
several logical drives on each array.
2) cat /proc/driver/cciss/cciss* in an infinite loop
3) delete some of the logical drives in the first "array."
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Currently we split seeky coop queues after 1s, which is too big. Below patch
marks seeky coop queue split_coop flag after one slice. After that, if new
requests come in, the queues will be splitted. Patch is suggested by Corrado.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Reviewed-by: Corrado Zoccolo <czoccolo@gmail.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The volume register is from 0..0x7f and 0..0x1a range is mute.
Also, fix mute combining in wm_vol_put(). The wrong behaviour was
noticed by Peter Christensen.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This renames the interrupt name in /proc/interrupt.
HDA Intel -> hda_intel
This also eliminates space from the name, probably helping some
parsers.
Don't think anybody depends on this name in userspace
Signed-off-by: Takashi Iwai <tiwai@suse.de>
My sound codec seems sometimes (very rarely) to omit interrupts (ALC268)
However, interrupt mode still works.
Thus if we get timeout, poll the codec once.
If we get 3 such polls in a row, then switch to polling mode.
This patch is maybe an bandaid, but this might be a workaround for hardware bug.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I found that the sampling rate locking setting of the ice1712 sound driver
was only half-respected : when the driver was locked to, let's say, 44100Hz,
and a usermode app was requesting 48000Hz playback, the request was succesful
although the soundcard would continue to run at 44100Hz.
Here's a patch that will make those requests to fail.
Signed-off-by: Sebastien Alaiwan <sebastien.alaiwan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Boot testing on my rs480 laptop found the MC idle never happened
on startup, a quick check with AMD found the idle bit is in a different
place on the rs4xx than r300.
Implement a new rs400 mc idle function to fix this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current root hub polling code exhibits a spinlock recursion on the
private controller lock. r8a66597_root_hub_control() is called from
r8a66597_timer() which grabs the lock and disables IRQs. The following
chain emerges:
r8a66597_timer() <-- lock taken
r8a66597_root_hub_control()
r8a66597_check_syssts()
usb_hcd_poll_rh_status() <-- acquires the same lock
/* insert death here */
The entire chain requires IRQs to be disabled, so we just unlock and
relock around the call to usb_hcd_poll_rh_status() while leaving the
IRQ state unchanged.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
This implements the same D-cache flushing logic for r8a66597-hcd as
Catalin's isp1760 (http://patchwork.kernel.org/patch/76391/) change,
with the same note applying here as well:
When the HDC driver writes the data to the transfer buffers it
pollutes the D-cache (unlike DMA drivers where the device writes
the data). If the corresponding pages get mapped into user space,
there are no additional cache flushing operations performed and
this causes random user space faults on architectures with
separate I and D caches (Harvard) or those with aliasing D-cache.
This fixes up crashes during USB boot on SH7724 and others:
http://marc.info/?l=linux-sh&m=126439837308912&w=2
Reported-by: Goda Yusuke <goda.yusuke@renesas.com>
Tested-by: Goda Yusuke <goda.yusuke@renesas.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was
redondant.
Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/radeon_combios.c: In function 'radeon_combios_get_lvds_info':
drivers/gpu/drm/radeon/radeon_combios.c:893: warning: comparison is always false due to limited range of data type
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix ati_pcigart printk format warning:
drivers/gpu/drm/ati_pcigart.c:115: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cache flush is required in case CPU is accessing rendered data.
This fixes glean/readPixSanity test case and random rendering
errors in sauerbraten and warzone2100.
v2 Fix comment ordering in r100_fence_ring_emit and remove extra
defines added in first version.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It seems that some R6XX/R7XX silently ignore HDP flush when
programmed through ring, this patch addback an ioctl callback
to allow R6XX/R7XX hw to perform such flush through MMIO in
order to fix a regression. For more details see:
http://bugzilla.kernel.org/show_bug.cgi?id=15186
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
VGA might be overwritting VRAM and corrupt our blit shader leading
to corruption, it likely won't happen if you load fbcon right after
radeon. Thanks to Shawn Starr and Andre Maasikas for tracking down
this issue.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Fix wrong register in proc-arm6_7.S data abort handler
ARM: 5909/1: ARM: Correct the FPSCR bits setting when raising exceptions
ARM: 5904/1: ARM: Always generate the IT instruction when compiling for Thumb-2
ARM: 5907/1: ARM: Fix the reset on the RealView PBX Development board
mx35: add a missing comma in a pad definition
mx25: make the FEC AHB clk secondary of the IPG
mx25: fix time accounting
mx25: properly initialize clocks
mx25: remove unused mx25_clocks_init() argument
i.MX25: implement secondary clocks for uarts and fec
i.MX25: Allow secondary clocks in DEFINE_CLOCK
ARM: MX3: Fixed typo in declared enum type name.
MXC: Add AUDMUXv2 register decode to debugfs
mx31ads: Provide an IRQ range to the WM835x on the 1133-EV1 module
mx31ads: Provide a name for EXPIO interrupt chip
mx31ads: Allow enable/disable of switchable supplies
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: Disable serial port autoidle by default
omap: Fix access to already released memory in clk_debugfs_register_one()
omap: Fix arch/arm/mach-omap2/mux.c: Off by one error
omap: Fix 3630 mux errors
OMAP2/3: GPMC: ensure valid clock pointer
OMAP2/3: IRQ: ensure valid base address
ARCH OMAP : enable ARCH_HAS_HOLES_MEMORYMODEL for OMAP
omap: Remove old unused defines for OMAP_32KSYNCT_BASE
omap: define _toggle_gpio_edge_triggering only for OMAP1
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Don't clobber the attribute type in nfs_update_inode()
NFS: Fix a umount race
NFS: Fix an Oops when truncating a file
NFS: Ensure that we handle NFS4ERR_STALE_STATEID correctly
NFSv4.1: Don't call nfs4_schedule_state_recovery() unnecessarily
NFSv4: Don't allow posix locking against servers that don't support it
NFSv4: Ensure that the NFSv4 locking can recover from stateid errors
NFS: Avoid warnings when CONFIG_NFS_V4=n
NFS: Make nfs_commitdata_release static
NFS: Try to commit unstable writes in nfs_release_page()
NFS: Fix a reference leak in nfs_wb_cancel_page()
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Handle futex value corruption gracefully
futex: Handle user space corruption gracefully
futex_lock_pi() key refcnt fix
softlockup: Add sched_clock_tick() to avoid kernel warning on kgdb resume
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Extend umount wait coverage to full glock lifetime
GFS2: Wait for unlock completion on umount
Commit 859ddf0974 tried to fix
misallocation bug but broke full bit marking by not clearing
pa[idp->layers] and also is causing X failures due to lookup failure
in drm code. The cause of the latter hasn't been found yet. Revert
the fix for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing try_to_freeze() to one of the pktgen_thread_worker() code
paths so that it doesn't block suspend/hibernation.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=15006
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Ciprian Dorin Craciun <ciprian.craciun@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After hours of debugging, I finally found the reason why some source
and runtime combination does not work. The PTP (page table pages)
address must be aligned. I am not sure how much, but alignment to
PAGE_SIZE is sufficient. Also, use ALSA's page allocation routines
to ensure proper virtual -> physical address translation.
Cc: <stable@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This change corrects an issue that will cause false hangs when using either
82575 or 82580 in legacy interrupt mode. The issue is caused when there is
a slow traffic flow and an "ethtool -r" is executed while using legacy or
MSI interrupts. MSI-X is not affected by this issue due to the fact that
we were already reconfiguring the vectors after reset.
If possible it would be best to push this for net-2.6 since it is resolving
a bug but if that is not possible then net-next-2.6 will be fine.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following a gpu hang, we would leak the relocation buffer. So simply
earrange the error path to always free the relocation buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
acpi_lid_open() could take up to 10ms on my computer. Some component is
calling the drm GETCONNECTOR ioctl many times in a row. This results in
flickering (for example, when starting a video). Fix it by assuming an
always connected lid status.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
Self Refresh should be disabled on dual plane configs. Otherwise, as
the SR watermark is not calculated for such configs, switching to non
VGA mode causes FIFO underrun and display flicker.
This fixes Korg Bug #14897.
Signed-off-by: David John <davidjon@xenontk.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
This version of the i_size fix for fallocate makes sure we only update
the i_size when the current fallocate is really operating outside of
i_size.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When running the following fio job
[torrent]
filename=torrent-test
rw=randwrite
size=4g
filesize=4g
bs=4k
ioengine=sync
you would see long stalls where no work was being done. That is because we were
doing all this extra work to read in the file extent outside of the transaction,
however in the random io case this ends up hurting us because the file extents
are not there to begin with. So axe this logic, since we end up reading in the
file extent when we go to update it anyway. This took the fio job from 11 mb/s
with several ~10 second stalls to 24 mb/s to a couple of 1-2 second stalls.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>