The patch to identify AIX disks and ignore them has caused at least one
machine to fail to find the root partition on 2.6.19. The patch is:
http://lkml.org/lkml/2006/7/31/117
The problem is some disk formatters do not blow away the first 4 bytes
of the disk. If the disk we are installing to used to have AIX on it,
then the first 4 bytes will still have IBMA in EBCDIC.
The install in question was debian etch. Im not sure what the best fix
is, perhaps the AIX detection code could check more than the first 4
bytes.
The whole partition info for primary partitions is in this block:
dd if=/dev/sdb count=$(( 4 * 16 )) bs=1 skip=$(( 0x1be ))
All other data do not matter, beside the 0x55aa marker at the end of the
first block.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some partitioning systems create special partitions that
span the entire disk. One example are Sun partitions, and
this whole-disk partition exists to tell the firmware the
extent of the entire device so it can load the boot block
and do other things.
Such partitions should not be treated as normal partitions,
because all the other partitions overlap this whole-disk one.
So we'd see multiple instances of the same UUID etc. which
we do not want. udev and friends can thus search for this
'whole_disk' attribute and use it to decide to ignore the
partition.
Signed-off-by: Fabio Massimo Di Nitto <fabbione@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides fault-injection capability for disk IO.
Boot option:
fail_make_request=<probability>,<interval>,<space>,<times>
<interval> -- specifies the interval of failures.
<probability> -- specifies how often it should fail in percent.
<space> -- specifies the size of free space where disk IO can be issued
safely in bytes.
<times> -- specifies how many times failures may happen at most.
Debugfs:
/debug/fail_make_request/interval
/debug/fail_make_request/probability
/debug/fail_make_request/specifies
/debug/fail_make_request/times
Example:
fail_make_request=10,100,0,-1
echo 1 > /sys/blocks/hda/hda1/make-it-fail
generic_make_request() on /dev/hda1 fails once per 10 times.
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check_partition() stops its probe once it hits an I/O error from the
partition checkers. This would prevent the actual partition checker
getting a chance to verify the partition.
So this patch lets check_partition() continue probing untill it hits a
success while recording the I/O error which might have been reported by the
checking routines.
Also, it does some cleanup of the partition methods for ibm, atari and
amiga to return -1 upon hitting an I/O error.
Signed-off-by: Suzuki K P <suzuki@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current rescan_partition implementation ignores the errors that comes from
the lower layer. It reports success for unknown partitions as well as I/O
error cases while reading the partition information.
The unknown partition is not (and will not be) considered as an error in the
kernel, since there are legal users of it (e.g, members of a RAID5 MD Device
or a new disk which is not partitioned at all ). Changing this behaviour
would scare the user about a serious problem with their disk and is not
recommended. Thus for both "unknown partitions" to the Linux (eg., DEC
VMS,Novell Netware) and the legal users of NULL partition, would still be
reported as "SUCCESS".
The patch attached here, scares the user about something which he does need to
worry about. i.e, returning -EIO on disk I/O errors while reading the
partition information.
Signed-off-by: Suzuki K P <suzuki@in.ibm.com>
Cc: Erik Mouw <erik@harddisk-recovery.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle errors thrown in disk_sysfs_symlinks(), and propagate back to
caller.
The callers and associated functions don't do a real good job of handling
kobject errors anyway (add_partition, register_disk, rescan_partitions), so
this should do until something better comes along.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of booleans to: generic-boolean.patch (2006-08-23)
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The on-disk data structures from AIX are not known, also the filesystem
layout is not known. There is a msdos partition signature at the end of
the first block, and the kernel recognizes 3 small (and overlapping)
partitions. But they are not usable. Maybe the firmware uses it to find
the bootloader for AIX, but AIX boots also if the first block is cleared.
This is the content of the partition table:
# dd if=/dev/sdb count=$(( 4 * 16 )) bs=1 skip=$(( 0x1be )) | xxd
0000000: 0000 0000 0000 0000 0000 0000 0000 0000 ................
0000010: 80ff ffff 41ff ffff 1b11 0000 381b 0000 ....A.......8...
0000020: 00ff ffff 41ff ffff 0211 0000 1900 0000 ....A...........
0000030: 80ff ffff 41ff ffff 1b11 0000 381b 0000 ....A.......8...
Handle the whole disk as empty disk.
This fixes also YaST which compares the output from parted (and formerly
fdisk) with /proc/partitions. fdisk recognizes the AIX label since a long
time, SuSE has a patch for parted to handle the disk label as unknown.
dmesg will look like this:
sda: [AIX] unknown partition table
Tested on an IBM B50 with AIX V4.3.3.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Albert Cahalan <acahalan@gmail.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current sun disklabel code uses a signed int for the sector count.
When partitions larger than 1 TB are used, the cast to a sector_t causes
the partition sizes to be invalid:
# cat /proc/paritions | grep sdan
66 112 2146435072 sdan
66 115 9223372036853660736 sdan3
66 120 9223372036853660736 sdan8
This patch switches the sector count to an unsigned int to fix this.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable mac partition table support per default also for a powermac config.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the partition code in fs/partitions/check.c to initialize a newly
detected partition's policy field with that of the containing block device
(see patch below).
My reasoning is that function set_disk_ro() in block/genhd.c modifies the
policy field (read-only indicator) of a disk and all contained partitions.
When a partition is detected after the call to set_disk_ro(), the policy
field of this partition will currently not inherit the disk's policy field.
This behavior poses a problem in cases where a block device can be
'logically de- and reactivated' like e.g. the s390 DASD driver because
partition detection may run after the policy field has been modified.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Acked-by: Al Viro <viro@ftp.linux.org.uk>
Makes-sense-to: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sometimes partitions claim to be larger than the reported capacity of a
disk device. This patch makes the kernel warn about those partitions.
We still permit these patitions to be used. Quoting Andries Brouwer
<Andries.Brouwer@cwi.nl>:
Case 1: The kernel is mistaken about the size of the disk. (There are
commands to clip a disk to a certain capacity, there are jumpers to tell a
disk that it should report a certain capacity etc. Usually this is because
of BIOS bugs. In bad cases the machine will crash in the BIOS and hence fail
to boot if the disk reports full capacity.) In such cases actually accessing
the blocks of the partition may work fine, or may work fine after running an
unclip utility. I wrote "setmax" some years ago precisely for this reason.
Case 2: There was a messy partition table (maybe just a rounding error) but
the actual filesystem on the partition is contained in the physical disk.
Now using the filesystem goes without problem.
Case 3: Both partition and filesystem extend beyond the end of the disk. In
forensic or debugging situations one often uses a copy of the start of a
disk. Now access beyond the end gives an expected I/O error.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Stephen Cameron <steve.cameron@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add read_mapping_page() which is used for callers that pass
mapping->a_ops->readpage as the filler for read_cache_page. This removes
some duplication from filesystem code.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Like the SUBSYTEM= key we find in the environment of the uevent, this
creates a generic "subsystem" link in sysfs for every device. Userspace
usually doesn't care at all if its a "class" or a "bus" device. This
provides an unified way to determine the subsytem of a device, regardless
of the way the driver core has created it.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure to clear the driverfs_dev pointer when we do del_gendisk() (on
disk removal), so that other users that may still have a ref to the disk
won't try to use the stale pointer.
Also move the KOBJ_REMOVE uevent handler up, so that the uevent still
has access to the driverfs_dev data.
This all should hopefully fix the problems with MMC umounts after device
removals that caused commit 56cf6504fc and
its reversal (1a2acc9e92).
Original problem reported by Todd Blumer and others.
Acked-by: Greg KH <gregkh@suse.de>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Erik Mouw <erik@harddisk-recovery.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Todd Blumer <todd@sdgsystems.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As noted further on the this file, some block devices have a / in their
name, so fix the "block:..." symlink name the same as the /sys/block name.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[BLOCK] delay all uevents until partition table is scanned
Here we delay the annoucement of all block device events until the
disk's partition table is scanned and all partition devices are already
created and sysfs is populated.
We have a bunch of old bugs for removable storage handling where we
probe successfully for a filesystem on the raw disk, but at the
same time the kernel recognizes a partition table and creates partition
devices.
Currently there is no sane way to tell if partitions will show up or not
at the time the disk device is announced to userspace. With the delayed
events we can simply skip any probe for a filesystem on the raw disk when
we find already present partitions.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove all the CONFIG_SYSFS stuff. That's supposed to all be implemented up
in header files.
Yes, the CONFIG_SYSFS=n data structures will be a little larger than
necessary, but that's a tradeoff we can decide to make.
Cc: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Creating "slaves" and "holders" directories in /sys/block/<disk> and
creating "holders" directory under /sys/block/<disk>/<partition>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Eric Van Hensbergen <ericvh@ericvh.myip.org>
Cc: Robert Love <rml@tech9.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DASD allows to open a device as soon as gendisk is registered, which means the
device is a fake device (capacity=0) and we do know nothing about blocksize
and partitions at that point of time. In case the device is opened by
someone, the bdev and inode creation is done with the fake device info and the
following partition detection code is just using the wrong data.
To avoid this modify the DASD state machine to make sure that the open is
rejected until the device analysis is either finished or an unformatted device
was detected.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Rio Karma portable MP3 player has its own proprietary partition table.
The partition layout is similar to a DOS boot sector but it begins at a
different offset and uses a different magic number (0xAB56 instead of
0xAA55). Add support for it to enable mounting the device.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
balamurugan reported a problem where it was possible to have
the various Acorn partition types selected in the configuration,
but ACORN_PARTITION disabled. Since ACORN_PARTITION controls
whether we build fs/partitions/acorn.c, this lead to undefined
references to the adfspart_check_TYPE symbols.
Fix this by making the Acorn partition type symbols depend on
ACORN_PARTITION.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Moved definition of CMS volume label to vtoc.h and modify partitions/ibm.c to
use this volume label definition instead of anonymous array.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Block devices need to add the block device name to the symlink they put
in the device directory, otherwise multiple symlinks of the same name
can be created. This matches the class system, which works the same
way, we just forgot to convert block at the same time.
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce a Kconfig symbol SPARC that is defined on both the sparc and
sparc64 architectures.
This symbol makes some dependencies more readable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having ->read_sectors and ->write_sectors, combine the two
into ->sectors[2] and similar for the other fields. This saves a branch
several places in the io path, since we don't have to care for what the
actual io direction is. On my x86-64 box, that's 200 bytes less text in
just the core (not counting the various drivers).
Signed-off-by: Jens Axboe <axboe@suse.de>
A "coldplug + udevstart" can be simple like this:
for i in /sys/block/*/*/uevent; do echo 1 > $i; done
for i in /sys/class/*/*/uevent; do echo 1 > $i; done
for i in /sys/bus/*/devices/*/uevent; do echo 1 > $i; done
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
struct gendisk has these two fields: stamp, stamp_idle. Update to
stamp_idle is always in sync with stamp and they are always the same.
Therefore, it does not add any value in having two fields tracking
same timestamp. Suggest to remove it.
Also, we should only update gendisk stats with non-zero value.
Advantage is that we don't have to needlessly calculate memory address,
and then add zero to the content.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch makes the following changes to the msdos partition code:
- remove CONFIG_NEC98_PARTITION leftovers
- make parse_bsd static
This patch was already ACK'ed by Andries Brouwer.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
