* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: pm: avoid writing the auxillary control register for ARMv7
ARM: pm: some ARMv7 requires a dsb in resume to ensure correctness
ARM: pm: arm920/926: fix number of registers saved
ARM: pm: CPU specific code should not overwrite r1 (v:p offset)
ARM: 7066/1: proc-v7: disable SCTLR.TE when disabling MMU
ARM: 7065/1: kexec: ensure new kernel is entered in ARM state
ARM: 7003/1: vexpress: Add clock definition for the SP805.
ARM: 7051/1: cpuimx* boards: fix mach-types errors
ARM: 7019/1: Footbridge: select CLKEVT_I8253 for ARCH_NETWINDER
ARM: 7015/1: ARM errata: Possible cache data corruption with hit-under-miss enabled
ARM: 7014/1: cache-l2x0: Fix L2 Cache size calculation.
ARM: 6967/1: ep93xx: ts72xx: fix board model detection
ARM: 6965/1: ep93xx: add model detection for ts-7300 and ts-7400 boards
ARM: cache: detect VIPT aliasing I-cache on ARMv6
ARM: twd: register clockevents device before enabling PPI
ARM: realview: ensure visibility of writes during reset
ARM: perf: make name of arm_pmu_type consistent
ARM: perf: fix prototype of release_pmu
ARM: fix perf build with uclibc toolchains
Add clock control support for sh7372 CMT hardware blocks.
No upstream sh7372 boards are making use of CMT3 + CMT4,
but the sh7372 hardware happens to come out of reset with
all CMT MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.
This patch relies on the recently merged
794d78f drivers: sh: late disabling of clocks V2
to make sure the unused clocks get disabled as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock control support for sh7372 MSIOF hardware blocks.
No upstream sh7372 boards are making use of MSIOF0->2,
but the sh7372 hardware happens to come out of reset with
all MSIOF MSTP clocks _enabled_, so to save power we need
to implement a fix in software to shut down unused clocks.
This patch relies on the recently merged
794d78f drivers: sh: late disabling of clocks V2
to make sure the unused clocks get disabled as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
USB-DMAC1 needs SMSTPCR4/MSTP407 controls, not MSTP214
this patch tested on mackerel board
Reported-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes support for the SGX interrupt source in
the sh7372 INTCS controller.
The SGX hardware block included in sh7372 is already hooked
up to the ARM Cortex-A8 core using the INTCA controller,
so SGX users are encouraged to make use of that interrupt
source instead.
Removing support for the SGX interrupt source in INTCS
simplifies the sh7372 power management code by allowing
us to assume that only INTCA needs to be powered on to
operate the SGX hardware.
If the INTCS interrupt source would be kept then the kernel
would be forced to deal with additional dependencies that does
not follow the regular power domain hiearachy. With this
patch in place we can safely power down INTCS while the
SGX is operating.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For ARMv7 kernels running in the non-secure world, writing to the
auxillary control register causes an abort, so we must avoid directly
writing the auxillary control register. If the ACR has already been
reinitialized by SoC code, don't try to restore it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a dsb after the isb to ensure that the previous writes to the
CP15 registers take effect before we enable the MMU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM920 and ARM926 save four registers, not three. Fix the size of
the suspend region required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
r1 stores the v:p offset from the CPU invariant resume code, and is
expected to be preserved by the CPU specific code. Overwriting it is
not a good idea.
We've managed to get away with it on sa1100 platforms because most
happen to have PHYS_OFFSET == PAGE_OFFSET, but that may not be the
case depending on kernel configuration. So fix this latent bug.
This fixes xsc3 as well which was saving and restoring this register
independently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpu_v7_reset disables the MMU and then branches to the provided address.
On Thumb-2 kernels, we should take care to clear the Thumb Exception
enable bit in the System Control Register, otherwise this may wreak
havok in the code to which we are branching (for example, an ARM kernel
image via kexec).
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 540b5738 ("ARM: 6999/1: head, zImage: Always Enter the kernel in
ARM state") mandates that the kernel should be entered in ARM state.
If a Thumb-2 kernel kexecs a new kernel image, we need to ensure that
we change state when branching to the new code. This patch replaces a
mov pc, lr with a bx lr on Thumb-2 kernels so that we transition to ARM
state if need be.
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
- Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes following building error:
--
arch/arm/mach-footbridge/dc21285.c: In function 'dc21285_preinit':
arch/arm/mach-footbridge/dc21285.c:299:2: error: 'vga_base' undeclared (first use in this function)
arch/arm/mach-footbridge/dc21285.c:299:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/arm/mach-footbridge/dc21285.o] Error 1
--
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
This patch fixed following building error:
--
arch/arm/mach-orion5x/pci.c: In function 'orion5x_pci_sys_setup':
arch/arm/mach-orion5x/pci.c:563:2: error: 'vga_base' undeclared (first use in this function)
arch/arm/mach-orion5x/pci.c:563:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/arm/mach-orion5x/pci.o] Error 1
make[1]: *** Waiting for unfinished jobs....
--
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Upstream commit d5341942d7 "PCI: Make the
struct pci_dev * argument of pci_fixup_irqs const." leaked an extra
"const" into an actual call site (vs a proto/decl) which causes this:
arch/arm/mach-orion5x/dns323-setup.c: In function 'dns323_pci_map_irq':
arch/arm/mach-orion5x/dns323-setup.c:80: error: expected expression before 'const'
arch/arm/mach-orion5x/dns323-setup.c:80: error: too few arguments to function 'orion5x_pci_map_irq'
make[3]: *** [arch/arm/mach-orion5x/dns323-setup.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Commit c03f007a8b (OMAP: PM:
omap_device: add system PM methods for PM domain handling) mistakenly
used SET_SYSTEM_SLEEP_PM_OPS() when trying to configure custom methods
for the PM domains noirq methods. Fix that by setting only the
suspend_noirq and resume_noirq methods with custom versions.
Note that all other PM domain methods (including the "normal"
suspend/resume methods) are populated using USE_PLATFORM_PM_SLEEP_OPS,
which configures them all to the default subsystem (platform_bus)
methods.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Associate the HDMI clock together with LCDC1 on sh7372.
Without this patch Suspend-to-RAM hangs on the boards
AP4EVB and Mackerel. The code hangs in the LCDC driver
where the software is waiting forever for the hardware to
power down. By explicitly associating the HDMI clock with
LCDC1 we can make sure the HDMI clock is enabled using
Runtime PM whenever the driver is accessing the hardware.
This HDMI and LCDC1 dependency is documented in the sh7372
data sheet. Older kernels did work as expected but the
recently merged (3.1-rc)
794d78f drivers: sh: late disabling of clocks V2
introduced code to turn off clocks lacking software reference
which happens to include the HDMI clock that is needed by
LCDC1 to operate as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This was a typo in clockdev declaration for at91sam9261 SoC.
Fix the kernel hanging when switching clocksource to TC (tcb_clksrc).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
It seems that an entry for the SP805 watchdog in the table of clocks was
missing. This results in the sp805_wdt driver rejecting the device with
the following errors:
sp805-wdt mb:wdt: Clock not found
sp805-wdt mb:wdt: Probe Failed!!!
sp805-wdt: probe of mb:wdt failed with error -2
While not obviously stated in the hardware docs, the onboard SP810's
"REFCLK" is connected to a 32.768KHz crystal, and this drives the
watchdog. Add a struct clk and corresponding lookup entry for it.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I made some changes to the entry in the ARM Machine Registry after
submission which was the wrong thing to do.
This patch should help to fix this error.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Should be passing the parent clk object when
calling for parent rate.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch increases reset delay from 50 usec to 80 usec for
USB HOST PHY. In order to reset USB HOST PHY controller properly,
a little extra time is required during its reset cycle.
Signed-off-by: Yulgon Kim <yulgon.kim@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds chained IRQ enter/exit functions to gpio interrupt
handler in order to function correctly on primary controllers with
different methods of flow control.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds chained IRQ enter/exit functions to external interrupt
handler in order to function correctly on primary controllers with
different methods of flow control.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds chained IRQ enter/exit functions to timer
interrupt handler in order to function correctly on primary
controllers with different methods of flow control.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When S3C_PM_DEBUG_LED_SMDK is enabled for suspend/resume debugging, the following
compilation error occurs:
arch/arm/mach-s3c64xx/pm.c: In function 's3c_pm_debug_smdkled':
arch/arm/mach-s3c64xx/pm.c:41: error: implicit declaration of function 'gpio_set_value'
arch/arm/mach-s3c64xx/pm.c:41: error: implicit declaration of function 'S3C64XX_GPN'
arch/arm/mach-s3c64xx/pm.c: In function 's3c64xx_pm_init':
arch/arm/mach-s3c64xx/pm.c:184: error: implicit declaration of function 'gpio_request'
arch/arm/mach-s3c64xx/pm.c:188: error: implicit declaration of function 'gpio_direction_output'
Fix the error by including linux/gpio.h
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fixed the following warning for S5PV210.
arch/arm/mach-s5pv210/pm.c: In function 's5pv210_pm_add':
arch/arm/mach-s5pv210/pm.c:139: warning: assignment from
incompatible pointer type
Also, staticized the function.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is a regression fix after migration to the external GIC.
The breakage has been introduced in commit 69644a8e23
("ARM: EXYNOS4: modify interrupt mappings for external GIC")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: added commit id]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
WARNING: vmlinux.o(.text+0xf47c): Section mismatch in reference from the function samsung_bl_set() to the (unknown reference) .init.data:(unknown)
The function samsung_bl_set() references
the (unknown reference) __initdata (unknown).
This is often because samsung_bl_set lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to commit 659fb32d1b
("replace irq_gc_ack() with {set,clr}_bit variants"), this
should be fixed.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since commit 8560a6cfc9
"arm: Footbridge: Use common i8253 clockevent",
ARCH_NETWINDER needs to select CLKEVT_I8253.
This patch fixes below build error with "make netwinder_defconfig".
LD .tmp_vmlinux1
arch/arm/mach-footbridge/built-in.o: In function `isa_timer_init':
isa-rtc.c:(.init.text+0x12c8): undefined reference to `clockevent_i8253_init'
isa-rtc.c:(.init.text+0x12d0): undefined reference to `i8253_clockevent'
arch/arm/mach-footbridge/built-in.o:(.data+0x198): undefined reference to `i8253_clockevent'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is a workaround for the 364296 ARM1136 r0p2 erratum (possible
cache data corruption with hit-under-miss enabled). It sets the
undocumented bit 31 in the auxiliary control register and the FI bit in
the control register, thus disabling hit-under-miss without putting the
processor into full low interrupt latency mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes L2 Cache size calculations for L2C-210, L2C-310 and
PL310, by changing the L2X0_AUX_CTRL_WAY_SIZE_MASK from 2 bits to 3
bits.
The Auxiliary Control Register for L2C-210, L2C-310 and PL310 has 3bits
[19:17] for Way size, however the existing code only uses 2 bits to
get this value. This results in incorrect cachesize calculations.
It also results in performing operations on the whole cache when we
erroneously decide that the range is big enough (due to l2x0_size being
too small) and also prints incorrect cachesize.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the obvious error in board detection logic, because according to the TS's
manual, the model is stored in the least three significant bits. For example
the byte read on my ts-7300 is 0x23 and the detection then fails.
Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
ARM: mmp: Change the way we use timer 0 as clockevent timer.
ARM: mmp: Switch to using timer 1 as clocksource timer.
ARM: mmp: Also start timer 1 on boot.
ARM: pxa168/gplugd: free correct GPIO
ARM: pxa168/gplugd: get rid of mfp-gplugd.h
ARM: pxa: fix logic error in PJ4 iWMMXt handling
mach-sa1100: fix PCI build problem
omap: timer: Set dmtimer used as clocksource in autoreload mode
OMAP3: am3517crane: remove NULL board_mux from board file
arm: mach-omap2: mux: use kstrdup()
arch:arm:plat-omap:iovmm: remove unused variable 'va'
Update Nook Color machine 3284 to common Encore name
am3505/3517: Various platform defines for UART4
OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
iMX: Fix build for iMX53
ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
OMAP3: beagle: don't touch omap_device internals
OMAP1: enable GENERIC_IRQ_CHIP
...
Linus Torvalds