The MEM_SWAPOUT crashpoint in LKDTM could be broken as some compilers
inline the call to shrink_page_list() and symbol lookup for this function
name fails. Replacing it with the function shrink_inactive_list(), which
is the only function calling shrink_page_list().
Signed-off-by: Ankita Garg <ankita@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/net/Kconfig says:
# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
so remove duplicate 'depends' uses of NETDEVICES.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes 64k page support by using PAGE_MASK and appropriate pagesize defines in several places.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removed define H_CB_ALIGNMENT which is already defined in include/asm-powerpc/hvcall.h
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix: Must check for nullpointer before dereferencing it - not afterwards.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes a bug reported in:
http://bugzilla.kernel.org/show_bug.cgi?id=7438
tg3_close() turns off the PHY if WoL and ASF are both disabled. On
the next tg3_open(), some devices such as the 5752M will not be
brought up correctly without a PHY reset early in the reset sequence.
The PHY clock is needed for some internal MAC blocks to function
correctly.
This problem is fixed by always resetting the PHY early in
tg3_reset_hw() when it is called from tg3_open() or tg3_resume().
tg3_setup_phy() can then be called later in the sequence without the
reset_phy parameter set to 1, since the PHY reset is already done.
Update version to 3.68.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: use MII hooks only if CONFIG_MII is enabled
USB Storage: unusual_devs.h entry for Sony Ericsson P990i
USB: xpad: additional USB id's added
USB: fix compiler issues with newer gcc versions
USB: HID: add blacklist AIRcable USB, little beautification
USB: usblp: fix system suspend for some systems
USB: failure in usblp's error path
usbtouchscreen: use endpoint address from endpoint descriptor
USB: sierra: Fix id for Sierra Wireless MC8755 in new table
USB: new VID/PID-combos for cp2101
hid-core: big-endian fix fix
USB: usb-storage: Unusual_dev update
USB: add another sierra wireless device id
Add support for PATA controllers of MCP67 to amd74xx.c.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
spin_lock_irq{save,restore} is incorrectly called here (the function can
sleep after acquring the lock).
done the necessary corrections and removed unwanted cli/sti.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
WARNING: vmlinux - Section mismatch: reference to .init.text:spi_register_board_info from __ksymtab_gpl between '__ksymtab_spi_register_board_info' (at offset 0xc032f7d0) and '__ksymtab_spi_alloc_master'
Fix this by removing the export.
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=7439
It looks like device registration in drivers/char/ipmi/ipmi_si_intf.c was
cleaned up and a small error was made when setting the class_mask. The fix
is simple as the correct mask value is defined in the code but is not used.
Acked-by: Corey Minyard <minyard@acm.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call sysdev_class_unregister() on failure in edac_sysfs_memctrl_setup()
and decrease identation level for clear logic.
Acked-by: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix module_param/sysfs file permission typo.
Clean up MODULE_PARM_DESC strings to avoid fancy (and incorrect)
formatting.
Fix header includes for lkdtm; add some needed ones, remove unused ones;
and fix this gcc warning:
drivers/misc/lkdtm.c:150: warning: 'struct buffer_head' declared inside parameter list
drivers/misc/lkdtm.c:150: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ankita Garg <ankita@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows udev to do something intelligent when an array becomes
available.
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix mcs7830 patch
The recent mcs7830 update to make the MII support sharable goofed various
pre-existing configurations in two ways:
- it made the usbnet infrastructure reference MII symbols even
when they're not needed in the kernel being built
- it didn't enable MII along with the mcs7830 minidriver
This patch fixes these two problems.
However, there does seem to be a Kconfig reverse dependency bug in that MII
gets wrongly enabled in some cases (like USBNET=y and USBNET_MII=n); I think
I've noticed that same problem in other situations too. So the result can
mean kernels being bloated by stuff that's needlessly enabled ... better
than wrongly being disabled, but contributing to bloat.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding additional USB vendor/product ID's for XBOX pads provided by the
XBOX Linux team.
Signed-off-by: Dominic Cerquetti <binary1230@yahoo.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove complaint from newer GCCs; they don't like forward function
declarations except in top-level contexts.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add AIRcable USBto USB-HID blacklist, makes some little
changes things in the Kconfig to make AIRcable USB look as all the rest
of drivers. And it removes the readme part that was on
Documentation/usb/usb-serial.txt because it is not needed anymore.
Signed-off-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this has been confirmed to fix suspend problems with usblp.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if urb submission fails due to a transient error here eg. ENOMEM
, the driver is dead. This fixes it.
Regards
Oliver
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
use the endpoint address from the endpoint descriptor instead of the hardcoding
it to 0x81. at least some ITM based screen use a different address and don't work
without this.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Ralf Lehmann <ralf@lehmann.cc>
Cc: J.P. Delport <jpdelport@csir.co.za>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new version of sierra.c has introduced tables for the 1 port and 3
port variants. The device id i added in my last patch needs to be added
to the 3 port table.
Signed-off-by: Jan Luebbe <jluebbe@lasnet.de>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
3 new VID/PID combinations (registered with Silicon Laboratories Inc.)
added for devices made by Lipowsky Industrie Elektronik GmbH all using
the CP2102 usb-to-serial converter (Baby-JTAG, Baby-LIN, HARP-1).
Signed-off-by: Bjorn Schneider <schneider@lipowsky.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adam Kropelin had posted 32-bit fix in June 2005 about two weeks after I
originally had posted my fixes for big endian support. Adam has a UPS
device which reports LINEV using 32-bits.
Added comments to describe the limitations of the code.
extract() is the same version I posted earlier and tested in user space.
Made similar changes to implement() routine. I've written (and will
shortly post) a test for implement(). Code tested on C3600 (parisc) with
USB keyboard/mouse attached.
I've dropped test_implement.c and a few other user space test programs on
http://iou.parisc-linux.org/~grundler/tests/
-rw-r--r-- 1 grundler grundler 1750 Oct 18 09:13 test_extract.c
-rw-r--r-- 1 grundler grundler 561 Jan 25 2006 test_ffs.c
-rw-r--r-- 1 grundler users 7175 Apr 8 2005 test_fls.c
-rw-r--r-- 1 grundler grundler 206 Sep 1 15:52 test_gettimeofday.c
-rw-r--r-- 1 grundler grundler 1886 Oct 19 09:20 test_implement.c
-rw-r--r-- 1 grundler users 2707 Jun 4 2005 test_unaligned.c
I would appreciate if someone else would look at the output of
test_implement.c to make it does The Right Thing.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Dmitry Torokhov <dtor@mail.ru>
Acked-By: Adam Kropelin <akropel1@rochester.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The protocol in this entry is needed for some versions of the device but
not others. This adds the NEED_OVERRIDE flag to prevent it complaining
to users who don't need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
As reported by Peter Kucmeroski and Jason Ganovsky.
Cc: Peter Kucmeroski <PKucmeroski@novell.com>
Cc: Jason Ganovsky <JGanovsky@novell.com>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI_MULTITHREAD_PROBE is an interesting feature, but in its current state
it seems to be more of a trap for users who accidentally enable it.
This patch lets PCI_MULTITHREAD_PROBE depend on BROKEN for 2.6.19.
The intention is to get this patch reversed in -mm as soon as it's in
Linus' tree, and reverse it for 2.6.20 or 2.6.21 after the fallout of
in-kernel problems PCI_MULTITHREAD_PROBE causes got fixed.
(akpm: I get enough bug reports already)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a front-end is disabled, card drivers that use it are compiled with
a stub version of the front-end's attach function. This way they have no
references to the front-end's code and don't need it to be loaded.
If a card driver is compiled into the kernel, and a front-end is a
module, then that front-end is effectively disabled wrt the card driver.
In this case, the card driver should get the stub version. This was not
happening.
The stub vs real attach function selection is changed so that when the
front-end is a module the real attach function is only used if the card
driver is a module as well. This means a module front-end will be
supported by card drivers that are modules and not supported by card
drivers compiled into the kernel.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TT DVB-C 2300 runs at 137 kHz I2C speed. short_delay mode did not work
reliably on fast machines with that speed. Increased max loop count from
20 to 50. Moved dummy access out of the loop.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The board did not return to analog mode since the board specific
"demod sleep" function was not called.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Technotrend 1500 T card have "inverted inversion". This patch fixes that.
Many thanks to Martin Zwickel from Technotrend for his confirmation and
correction proposal.
Signed-off-by: Raymond Mantchala <raymond.mantchala@streamvision.fr>
Signed-off-by: Perceval Anichini <perceval.anichini@streamvision.fr>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix sparse NULL usage warnings:
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:714:14: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:715:16: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1079:10: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:224:58: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IR chip has no address decoding, so the IR data is always present in
the high byte when doing a read from the saa7146 chip. This means that
the DEBI address used is irrelevant to the IR decoding logic.
DEBI addresses 0x1XXX are mapped to the registers on the CI module
itself, but only the lowest two bits are actually used (see EN50221,
section A.2.2.1), meaning that 0x1234 is equivalent to 0x1000 which maps
to register 0 (the data register). A read from the data register is
supposed to be preceded by a read from the size register, so some CI
modules will be confused (the AlphaCrypt CAM will hang completely).
The attached patch changes the address used when reading the IR data to
use 0x4000 instead. This is the CI version address, which is a safer
default, works with the AlphaCrypt CAM and matches the behaviour of the
Windows driver (AFAIK).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Let the MT2060 be customized like most of the other DVB PLLs/front-ends.
Also, add a missing dependency on I2C.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/addr: Use client registration to fix module unload race
IB/mthca: Fix MAD extended header format for MAD_IFC firmware command
IB/uverbs: Return sq_draining value in query_qp response
IB/amso1100: Fix incorrect pr_debug()
IB/amso1100: Use dma_alloc_coherent() instead of kmalloc/dma_map_single
IB/ehca: Fix eHCA driver compilation for uniprocessor
RDMA/cma: rdma_bind_addr() leaks a cma_dev reference count
IB/iser: Start connection after enabling iSER
Require registration with ib_addr module to prevent caller from
unloading while a callback is in progress.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This reverts commit f833229c96c0bf53c05995e4bd58709d9e9edd67:
According to reviewers and the lspci data provided in commit message
itself, PCI ID 0x7110 should not have been added to ata_piix.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Make alignment exception always check exception table
[POWERPC] Disallow kprobes on emulate_step and branch_taken
[POWERPC] Make mmiowb's io_sync preempt safe
[POWERPC] Make high hugepage areas preempt safe
[POWERPC] Make current preempt-safe
[POWERPC] qe_lib: qe_issue_cmd writes wrong value to CECDR
[POWERPC] Use 4kB iommu pages even on 64kB-page systems
[POWERPC] Fix oprofile support for e500 in arch/powerpc
[POWERPC] Fix rmb() for e500-based machines it
[POWERPC] Fix various offb issues
ahci_softreset() used to use ahci_tf_read() which reads D2H_REG area
to check for the Status register. However, this area is zeroed on
initialization and not set by initial signature FIS. Replace it with
ahci_check_status().
This bug prevented CLO code from being activated whenever BSY and/or
DRQ is set prior to softreset. This fix makes
AHCI_FLAG_RESET_NEEDS_CLO flag redundant.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] ata_piix: allow 01b MAP for both ICH6M and ICH7M
[PATCH] libata: unexport ata_dev_revalidate()
[PATCH] Add 0x7110 piix to ata_piix.c
[PATCH] sata_sis: fix flags handling for the secondary port
This patch fixes a few issues in offb:
- A test was inverted causing the palette hack to never work
(no device node was passed down to the init function)
- Some cards seem to have their assigned-addresses property in a random
order, thus we need to try using of_get_pci_address() first, which will
fail if it's not a PCI device, and fallback to of_get_address() in that
case. of_get_pci_address() properly parsees assigned-addresses to test
the BAR number and thus will get it right whatever the order is.
- Some cards (like GXT4500) provide a linebytes of 0xffffffff in the
device-tree which does no good. This patch handles that by using the
screen width when that happens. (Also fixes btext.c while at it).
- Add detection of the GXT4500 in addition to the GXT2000 for the
palette hacks (we use the same hack, palette is linear in register space
at offset 0x6000).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bcm43xx driver uses 4 locations in the devices sprom to determine
the behavior of the leds. Certain defaults are assigned if all bits are
set in those locations. On at least one BCM4303 chip, the sprom contains
values other than the default, which executes an assertion placed in the
default case of a following switch statement. This patch makes the leds
on the above mentioned interface behave correctly. In addition, it limits
the number of logged messages to 20 for the case of unexpected values in
the sprom locations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a netdev watchdog timeout problem.
The software needs to call netif_tx_disable before running the
hardware calibration code. The problem condition can be shown by the
following timegraph.
|---5secs - ~10 jiffies time---|---|OOPS
^ ^
last real TX periodic work stops netif
At OOPS, the following happens:
The watchdog timer triggers, because the timeout of 5secs
is over. The watchdog first checks for stopped TX.
_Usually_ TX is only stopped from the TX handler to indicate
a full TX queue. But this is different. We need to stop TX here,
regardless of the TX queue state. So the watchdog recognizes
the stopped device and assumes it is stopped due to full
TX queues (Which is a _wrong_ assumption in this case). It then
tests how far the last TX has been in the past. If it's more than
5secs (which is the case for low or no traffic), it will fire
a TX timeout.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the manfid CIS should be at least 4, and it's normally 4.
It's incorrect to require it to be at least 5. This breaks support for
most (if not all) cards.
The right place to ensure that we don't access beyond the CIS buffer is
to strengthen another check. Make sure that the next tuple begins at
least at the CIS buffer end (in which case we stop processing) or
before that.
Reported by ph35sm@free.fr
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ICH7M was separated from ICH6M to allow undocumented MAP value 01b
which was spotted on an ASUS notebook. However, there is also
notebooks with MAP value 01b on ICH6M. This patch re-merges ICH6M and
ICH7M entries and allows MAP value 01b for both.
This problem has been reported and initial patch provided by Jonathan
Dieter.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jonathan Dieter <jdieter@gmail.com>
Cc: Tom Deblauwe <tom.deblauwe@telenet.be>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_revalidate() isn't used outside of libata core. Unexport it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi Jeff,
I tested the PATA support on my old VAIO notebook, and it failed to find
my piix device:
00:07.1 Class 0101: 8086:7111 (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at fc90 [size=16]
This patch adds the pci id to ata_piix.c and things then work as
expected.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sis_init_one() modifies probe_ent->port_flags after allocating and
initializing it using ata_pci_init_native_mode(). This makes port_flags
for the secondary port (probe_ent->pinfo2->flags) go out of sync resulting
in misdetection of device due to incorrectly initialized SCR access flag.
This patch make probe_ent alloc/init happen after the final port flags
value is determined. This is fragile but probe_ent and all the related
mess are scheduled to go away soon for exactly this reason. We just need
to hold everything together till then.
This has been spotted and diagnosed and tested by Patrick McHardy.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Patric McHardy <kaber@trash.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2 driver uses a single NAPI poll routine for both ports on dual ported
cards (because there is a single IRQ and status ring). Netpoll makes assumptions
about the relationship between network device and NAPI that aren't correct
on the second port, this will cause the port to never clear work.
Most systems, just have single port, so not a big issue.
The easy fix is just make the second port, not netpoll capable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I don't want my code to downgraded to GPLv3 because of
cut-n-pasted the comments. These files which I hold copyright
on were started before it was clear what GPLv3 was going to be.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Checks for NULL dev_alloc_skb() and returns on true to avoid subsequent
dereference.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Christoph Hellwig <hch@infrared.org>
Signed-off-by: David Rientjes <rientjes@cs.washington.edu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to keep defining PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE
in the driver code since it is now defined in pci_ids.h.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2 driver is no longer in experimental state.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
modprobe n2 with no parameters or no such devices
will get confusing error message.
# modprobe n2
... Kernel does not have module support
This patch replaces return code from -ENOSYS to -EINVAL.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
drivers/net/wan/n2.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Call platform_driver_unregister() before return when no cards found.
(fixes data corruption when no cards found)
- Check platform_device_register_simple() return value
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Mike Phillips <mikep@linuxtr.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
drivers/net/tokenring/proteon.c | 9 +++++++--
drivers/net/tokenring/skisa.c | 9 +++++++--
2 files changed, 14 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Flooding the console with error messages for every RX FIFO overrun,
checksum error and framing error isn't very sensible. Each of these
errors can occur during normal operation, so stop printk'ing error
messages for RX errors at all.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ray Lehtiniemi reported that an incoming UDP packet flood can lock up
the ep93xx ethernet driver. Herbert Valerio Riedel noted that due to
the way ep93xx_eth manages the RX/TXstatus rings, it cannot distinguish
a full ring from an empty one, and correctly suggested that this was
likely to be causing this lockup to occur.
Instead of looking at the hardware's RX/TXstatus ring write pointers
to determine when to stop reading from those rings, we should just check
every individual RX/TXstatus descriptor's valid bit instead, since there
is no other way to distinguish an empty ring from a full ring, and if
there is a descriptor waiting, we take the hit of reading the descriptor
from memory anyway.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several fields in an incoming MAD extended info header were passed
into the MAD_IFC firmware command at incorrect offsets (mostly off by
4 bytes). As the result, the HCA will fail to generate traps in which
this info is needed (e.g. traps which include the GRH of the incoming
packet), in violation of the IB spec.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SCSI_QLA_ISCSI needs to depend on NET to prevent build (link) failures
that are caused by selecting SCSI_ISCSI_ATTRS.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Return the sq_draining value back to user space for query_qp instead
of the en_sqd_async notify value, which is valid only for
modify_qp. For query_qp, the draining status should returned.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The Ammasso driver needs to use dma_alloc_coherent() for
allocating memory that will be used by the HW for dma.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The eHCA driver does not compile for a uniprocessor configuration
(CONFIG_SMP=n), due to H_SUCCESS and other symbols being undefined.
This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Hoang-Nam Nguyen <HNGUYEN@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a connection is started (a new connection or a recovered one),
iSER should prepare its resources for full-featured mode and only then
notify the iSCSI layer that it is ready to start queueing commands.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hp6xx.h header moved location, causing the build to fail,
fix it up.
Signed-off-by: Kristoffer Ericson <kristoffer_e1@hotmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Several u64 objects are derefernced in situations where the
pointer is not guarenteed to be aligned correctly. Use
get_unaligned() as needed.
Thanks to Will Simoneau for lots of testing and debugging
help.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On Wed, 25 Oct 2006 18:03:13 +0200 Toralf Förster wrote:
> WARNING: "arp_broken_ops" [drivers/net/wan/sealevel.ko] undefined!
> make[1]: *** [__modpost] Error 1
> make: *** [modules] Error 2
>
> Here's the config:
...
> # CONFIG_INET is not set
> CONFIG_SEALEVEL_4021=m
Sealevel uses arp_broken_ops so it needs to depend on INET.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When gigaset_initbcs() is called, cs->dev is not initialized yet. If
dev_alloc_skb() failed in this function, NULL poinster dereference will
happen at dev_warn().
Cc: Kai Germaschewski <kai.germaschewski@gmx.de>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix dm-crypt after the block cipher API changes to correctly return the
backwards compatible cipher-chainmode[-ivmode] format for "dmsetup
table".
Signed-off-by: Christophe Saout <christophe@saout.de>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
diff linux-2.6.19-rc3.orig/drivers/md/dm-crypt.c linux-2.6.19-rc3/drivers/md/dm-crypt.c
This reverts commit a2b98a697f.
As per Guennadi Liakhovetski, the mac address change support code breaks
some normal uses (_without_ any address changes), and until it's all
sorted out, we're better off without it.
Says Francois:
"Go revert it.
Despite what I claimed, I can not find a third-party confirmation by
email that it works elsewhere.
It would probably be enough to remove the call to
__rtl8169_set_mac_addr() in rtl8169_hw_start() though."
See also
http://bugzilla.kernel.org/show_bug.cgi?id=6032
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3914/1: [Jornada7xx] - Typo Fix in cpu-sa1110.c (b != B)
[ARM] 3913/1: n2100: fix IRQ routing for second ethernet port
[ARM] Add KBUILD_IMAGE target support
[ARM] Fix suspend oops caused by PXA2xx PCMCIA driver
[ARM] Fix i2c-pxa slave mode support
[ARM] 3900/1: Fix VFP Division by Zero exception handling.
[ARM] 3899/1: Fix the normalization of the denormal double precision number.
[ARM] 3909/1: Disable UWIND_INFO for ARM (again)
[ARM] Add __must_check to uaccess functions
[ARM] Add realview SMP default configuration
[ARM] Fix SMP irqflags support
If no devices found or invalid parameter is specified,
scl200wdt_pnp_driver is left unregistered.
It breaks global list of pnp drivers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Some errors during preparation for suspended state can be skipped with a
warning instead of a failure of the whole suspend transition, notably an
error in pci_set_power_state.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The PXA2xx PCMCIA driver was registering a device_driver with the
platform_bus_type. Unfortunately, this causes data outside the
device_driver structure to be dereferenced as if it were a
platform_driver structure, causing an oops. Convert the PXA2xx
core driver to use the proper platform_driver structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i2c-pxa times out when trying to enable slave mode due to an
incorrect test. Also, check that i2c->slave is non-NULL
before dereferencing it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] cio: Make ccw_device_register() static.
[S390] Improve AP bus device removal.
[S390] uaccess error handling.
[S390] cio: css_probe_device() must be called enabled.
[S390] Initialize interval value to 0.
[S390] sys_getcpu compat wrapper.
The Jmicron JMB368 is PATA only so has the PATA on function zero. Don't
therefore skip function zero on this device when probing
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Put SYS_HYPERVISOR inside the Generic Driver Config menu where it should
be. Otherwise xconfig displays it as a dangling (lost) menu item under
Device Drivers, all by itself (when all options are displayed).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <holzheu@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix printk format warnings:
drivers/block/cciss.c:2000: warning: long long int format, long unsigned int arg (arg 2)
drivers/block/cciss.c:2035: warning: long long int format, long unsigned int arg (arg 2)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix printk format warning:
drivers/misc/ioc4.c:213: warning: long long int format, u64 arg (arg 3)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/md/raid1.c:1479: warning: long long unsigned int format, long unsigned int arg (arg 4)
drivers/md/raid10.c:1475: warning: long long unsigned int format, long unsigned int arg (arg 4)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent fix which made sure ->degraded was initialised properly exposed a
second bug - ->degraded wasn't been updated when drives failed or were
hot-added.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When "mdadm --grow --size=xxx" is used to resize an array (use more or less of
each device), we check the new siza against the available space in each
device.
We already have that number recorded in rdev->size, so calculating it is
pointless (and wrong in one obscure case).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If save_raid_disk is >= 0, then the device could be a device that is already
in sync that is being re-added. So we need to default this value to -1.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Remove quirk_via_abnormal_poweroff
PCI: reset pci device state to unknown state for resume
PCI: x86-64: mmconfig missing printk levels
PCI: fix pci_fixup_video as it blows up on sparc64
acpiphp: fix latch status
Add description of 'raw' in comments for
drivers/mtd/nand/nand_base.c::nand_write_page_syndrome() so 'make xmldocs'
will not spew a warning at us.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The multithreaded-probing code has a problem: after one initcall level (eg,
core_initcall) has been processed, we will then start processing the next
level (postcore_initcall) while the kernel threads which are handling
core_initcall are still executing. This breaks the guarantees which the
layered initcalls previously gave us.
IOW, we want to be multithreaded _within_ an initcall level, but not between
different levels.
Fix that up by causing the probing code to wait for all outstanding probes at
one level to complete before we start processing the next level.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My K8T800 mobo resumes fine from suspend to ram with and without patch
applied against 2.6.18.
quirk_via_abnormal_poweroff makes some boards not boot 2.6.18, so IMO patch
should go to head, 2.6.18.2 and everywhere "ACPI: ACPICA 20060623" has been
applied.
Remove quirk_via_abnormal_poweroff
Obsoleted by "ACPI: ACPICA 20060623":
<snip>
Implemented support for "ignored" bits in the ACPI
registers. According to the ACPI specification, these
bits should be preserved when writing the registers via
a read/modify/write cycle. There are 3 bits preserved
in this manner: PM1_CONTROL[0] (SCI_EN), PM1_CONTROL[9],
and PM1_STATUS[11].
http://bugzilla.kernel.org/show_bug.cgi?id=3691
</snip>
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: Bob Moore <robert.moore@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Considering below scenario:
1.Unload a PCI device's driver, the device ->current remains in PCI_D0.
2.Do suspend/resume circle. After that, BIOS puts the device to D3.
3.Reload the device driver. The calling pci_set_power_state in the
driver can't change the state to D0, as set_power_state thinks the
device is already in D0.
A bug is reported at http://bugzilla.kernel.org/show_bug.cgi?id=6024
Pat attached a patch at
http://marc.theaimsgroup.com/?l=linux-pci&m=114049761428561&w=2 for this
issue, but it's lost. As pci_set_power_state can handle D3 -> D0
correctly (restore config space), I simplified Patrick's patch.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts much of the original pci_fixup_video change and makes it
work for all arches that need it.
fixed, and tested on x86, x86_64 and IA64 dig.
Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_hotplug.h says:
* @latch_status: if the latch (if any) is open or closed (1/0)
However, acpiphp returns opposite value.
This patch fixes this issue.
I tested this patch on my ia64 machine that has some apciphp based
hotplug slots.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ccw_device_register() is only called from io_subchannel_register()
and io_subchannel_probe() and will never be called for possible
non-io subchannels.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Added a call to device_unregister() in ap_scan_bus() to actively
remove unavailable AP bus devices with every bus scan. Previously
devices were only removed in ap_queue_message() or __ap_poll_all().
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move css_probe_device() behind giving up the lock for the old subchannel
in css_evaluate_known_subchannel() so we aren't disabled when we call it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
dp->path_component_name can be larger than ->bus_id[]
so use a different naming scheme for this stuff.
Noticed by Jurij Smakov.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'intelfb-patches' of master.kernel.org:/pub/scm/linux/kernel/git/airlied/intelfb-2.6:
Remove unnecessary check in drivers/video/intelfb/intelfbhw.c
intel fb: switch to pci_get API
* 'drm-patches' of master.kernel.org:/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: ioremap balanced with iounmap for drivers/char/drm
drm: fix error returns, sysfs error handling
fix return code in error case.
drm: mga: set dev_priv_size
drm: savage: dev->agp_buffer_map is not initialized for AGP DMA on savages
drm: radeon: only allow specific type-3 packetss through verifier
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The previous code did something like,
if (error) goto out_err;
....
do {
struct au1000_pcmcia_socket *skt = PCMCIA_SOCKET(i);
del_timer_sync(&skt->poll_timer);
pcmcia_unregister_socket(&skt->socket);
out_err:
flush_scheduled_work();
ops->hw_shutdown(skt);
i--;
} while (i > 0)
.....
- On the error path, skt would not contain a valid value for the first
iteration (skt is masked by uninitialized automatic skt)
- Does not do hw_shutdown() for 0th element of PCMCIA_SOCKET
Signed-off-by: Om Narasimhan <om.turyx@gmail.com>
Cc: "Yoichi Yuasa" <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
debugging goo removed to not leave assymetry in it after possible "leave"
removal.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove some code which is unneeded if CONFIG_PM=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Some PCMCIA cards do not mention specific IO addresses in the CIS. In that
case, inside the alloc_io_space function, conflicts are detected (the
function returns 1) for the second function of a multifunction card unless
the length of IO address range required is greater than 0x100.
The following patch will remove this conflict checking for a PCMCIA
function which had not mentioned any specific IO address to be mapped from.
The patch is tested for Linux kernel 2.6.15.4 and works fine in the above
case and is as suggested by Dave Hinds.
Signed-off-by: Kaustav Majumdar <kaustav.majumdar@wipro.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As a replacement for the broad manufactor/card ID match we commented out
because of conflicts with pcnet_cs, add two product ID matches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
More correct AT91 CF wakeup logic ... only enable/disable the IRQ wakeup
capability, not the IRQ itself. That way the we know that the IRQ will be
disabled correctly, in suspend/resume logic instead of ARM IRQ code.
Most of the pin multiplexing setup has moved to the devices.c setup code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This is a cross-port of a similar patch for aic7xxx;
only it's a bit simpler here as we don't support HVD
and all controller actually implement this register.
I hope.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a cross-port from aic79xx; we still hit the occasional
BUG_ON in slave_destroy. And again we don't really need the
slave_destroy callback nor the ahc_linux_target structure
at all.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
aic79xx has a special 'iocell' chip which handles the precompensation.
If it's set via DV we should make sure to set the chip correctly, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Whenever an external device is resetted we really have to take
care to keep the channel in sync. Just notifying SCSI-ML and retry
is not enough as we have to make sure the SCSI bus is not getting
confused, either.
So whenever we detect an external reset we rewrite the command to
TUR, disable packetized command and notify the internal engine
that an abort has happened. This way we trigger a proper bus
reset sequence and all devices will be renegotiated properly.
Kudos to Justin Gibbs and Luben Tuikov for this idea.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix printk format warning:
drivers/scsi/lpfc/lpfc_attr.c:597: warning: long long unsigned int format, uint64_t arg (arg 4)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- make needlessly global code static
- #if 0 the following unused global functions:
- aic79xx_core.c: ahd_print_scb
- aic79xx_core.c: ahd_suspend
- aic79xx_core.c: ahd_resume
- aic79xx_core.c: ahd_dump_scbs
- aic79xx_osm.c: ahd_softc_comp
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanups done to use min/max macros from kernel.h. Handcrafted MIN/MAX
macros are changed to use macros in kernel.h
[akpm@osdl.org: fix warning]
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for REPORT TARGET PORT GROUPS. This is used
eg for the multipathing priority callout to determine the path
priority.
With this patch multipath-tools can use the existing mpath_prio_alua
callout to exercise the path priority grouping.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix typo in check of return value of qla1280_bus_reset() which would
result in an adapter reset in addition to the bus reset.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to the iscsi RFC, we cannot send other requests if
we have sent a logout pdu. This patch enforces this requirement
by blocking the session and suspending the send thread. Userspace
decides if we restart the connection or if we just free everything.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have been dropping the pdu. We should just send it to userspace
and let it handle it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from bhalevy@gmail.com:
It looks like change 652 to libiscsi.c added some dead code around line
670
if (rc) {
spin_unlock_bh(&conn->session->lock);
goto again;
}
since 5 lines above we goto again if (rc).
It looks like the previous if (rc) should go away if we want to put the
ctask before
breaking out of the while loop with "goto again" (see following patch).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If connection creation fails we end up calling list_del
on a invalid struct. This then causes an oops. We are not
acutally using the lists (old MCS code we thought might
be useful elsewhere) so this patch just removes that
code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The transport class recv mempools are causing slab corruption.
We could hack around netlink's lack of mempool support like dm,
but it is just too ulgy (dm's hack is ugly enough :) when you need
to support broadcast.
This patch removes the recv pools. We have not used them even when
we were allocting 20 MB per session and the system only had 64 MBs.
And we have no pools on the send side and have been ok there. When
Peter's work gets merged we can use that since the network guys
are in favor of that approach and are not going to add mempools
everywhere.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Doesn't make the hardware hot pluggable but does ensure the driver won't
crash when another device is hot-unplugged at the wrong moment. Soon I
propose to deprecate pci_find_device() and some of its friends.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Debugging TCQ issues has shown me this is a very useful parameter to be
able to view. Add it to he host class parameters.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It is known that 2 LSI Logic MegaRAID SATA RAID Controllers (150-4 and
150-6) don't support 64-bit DMA. Unfortunately currently this check is
wrong and driver sets 64-bit DMA mode for these devices.
Signed-off-by: Andrey Mirkin <amirkin@sw.ru>
Acked-by: "Ju, Seokmann" <Seokmann.Ju@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add PCI id. Plus correct for possibly missing resistor that can cause
FLASHEX to have the wrong value.
Signed-off-by: Sergey Kononenko <sergk@sergk.org.ua>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The "ibmvscsi: treat busy and error conditions separately" patch
submitted by Dave Boutcher back in June incorrectly reenables the CRQ.
The broken logic causes the adapter to get disabled if the CRQ
connection happens to close temporarily. This patch "fixes that
obviously wrong logic check" (Dave's words).
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: David Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Drop queue-depths across all luns for a given fcport
during TASK_SET_FULL statuses.
- Ramp-up I/Os after throttling.
- Consolidate completion-status handling of CS_QUEUE_FULL with
CS_COMPLETE as ISP24xx firmware no longer reports
CS_QUEUE_FULL.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Early ISP2432 parts have a known hardware issue when coming
out of a D3 hot state. This issue can result in a hung PCIe
link. Recent firmwares contain a workaround whereby the
stop-firmware mailbox command prevents the ISP from entering
the D3 hot state.
In order to ensure that the workaround succeeded the driver
must verify that the stop-firmware mailbox command completes
successfully. In the event of a failure, the driver
attempts a shutdown-retry after resetting the ISP and
re-executing firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in the Fibre Channel
driver (fc4).
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete typedefd Scsi_Cmnd to struct scsi_cmnd in
the ninja scsi pcmcia driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in psi240i-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we fail to allocate mp->virt during the first while loop iteration,
mlist is still uninitialized, therefore we should check if before
dereferencing.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes a typo in the aic7xxx_old.c.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Thanks to James Smart for the inspiration.
Stall error handler if attempting recovery while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Also verify that VirtDevice is available before issuing scsi command.
VirtDevice is removed when fc transport removes a target.
See James Smart's patch of 08/17/2006 for greater detail.
http://marc.theaimsgroup.com/?l=linux-scsi&m=115583213624803&w=2
Also bump version number per Eric's request.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Eric Moore <eric.moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to the adaptec sources aic7xxx / aic79xx really can do
4MB transfers. So we should adjust .max_sectors.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a dup printk at the tail of qla4xxx_module_init(). Remove the
first instance as it's before the complete success of the function.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
AM53C974A's Start Transfer Counter register has 24 bits, thus
maximum transfer length is 16MiB. But the maximum I can test
is 8MiB, so use that until somebody tests 16MiB.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Based on the original patch from Hannes Reinecke <hare@suse.de>
Fix st_open() to return -ENOMEDIUM instead of -EIO if no medium is
found.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change obsolete Scsi_Cmnd to struct scsi_cmnd in the Qlocic FAS408 driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change the obsolete Scsi_Cmnd to struct scsi_cmnd in the sun3-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
All callers and the function itself dereference dinfo, so we can remove the
check. (coverity id #1371)
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only) to make sure the files are compiling without
any warning/error due to new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
- callers of drm_sysfs_create() and drm_sysfs_device_add() looked for
errors using IS_ERR(), but the functions themselves only ever returned
NULL on error. Fixed.
- unwind from, and propagate sysfs errors
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The other failure returns in this function are negative, so make
this one do the same.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
CRYPTO_MANAGER is selected automatically by CONFIG_ECB and CONFIG_CBC.
config CRYPTO_ECB
tristate "ECB support"
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
I've added CONFIG_ECB to the ones you mentioned and CONFIG_CBC to
gssapi.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Account for the interface being closed before disabling polling
on a device, to fix shutdown on some systems that explcitly close
the netdevice before calling shutdown.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Move the length (rx_bytes counter) adjustment of 4 bytes down to after the
TBI_ACCEPT workaround.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
82571 and newer chispets don't need to limit desc. length to 4kb and can
handle 8kb sizes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allocations using alloc_page are taking too long for normal MTU, so
use LPE only for jumbo frames.
Signed-off-bu: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Threshold bitmasks for prefetch, host and writeback were clearing
bits that they were not supposed to. The leftmost 2 bits in the byte
for each threshold are reserved.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The MANC register should not be read for PCI-E adapters at all, as well as
82543 and older where 82543 would master abort when this register was
accessed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Fix module loading:
corgi_bl: module license 'GPLv2' taints kernel.
corgi_bl: Unknown symbol platform_driver_unregister
corgi_bl: Unknown symbol __symbol_get
corgi_bl: Unknown symbol platform_driver_register
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix module compiling:
WARNING: drivers/video/backlight/corgi_bl.o - Section mismatch:
reference to .init.text: from .data between '$d' (at offset 0x0) and
'bl_mutex'
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
only allow specific type-3 packets to pass the verifier instead of all for r100/r200 as others might be unsafe (r300 already does this), and add checking for these we need but aren't safe. Check the RADEON_CP_INDX_BUFFER packet on both r200 and r300 as it isn't safe neither.
Signed-off-by: Dave Airlie <airlied@linux.ie>
In commit 4e8a520150 ("[PKT_SCHED] netem:
Orphan SKB when adding to queue.") Davem mistakenly also included a
temporary diff in his tree that disabled the pci_fixup_video VGA quirk,
which broke sparc64.
This reverts that part of the commit. Sayeth Davem:
"Greg KH has a patch coming to you soon which will move that VGA code
back into x86/x86_64/IA64 specific areas and will fix the sparc64
problem properly."
Special thanks to Claudio Martins <ctpm@ist.utl.pt> for noticing the
error in the first place.
Cc: Claudio Martins <ctpm@ist.utl.pt>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[PKT_SCHED] netem: Orphan SKB when adding to queue.
[NET]: kernel-doc fix for sock.h
[NET]: Reduce sizeof(struct flowi) by 20 bytes.
[IPv6] fib: initialize tb6_lock in common place to give lockdep a key
[ATM] nicstar: Fix a bogus casting warning
[ATM] firestream: handle thrown error
[ATM]: No need to return void
[ATM]: handle sysfs errors
[DCCP] ipv6: Fix opt_skb leak.
[DCCP]: Fix Oops in DCCPv6
The networking emulator can queue SKBs for a very long
time, so if you're using netem on the sender side for
large bandwidth/delay product testing, the SKB socket
send queue sizes become artificially larger.
Correct this by calling skb_orphan() in netem_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Not enough to make Nicstar 64bit friendly but got squashed in passing so might
as well be applied
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc emits the following warning:
drivers/atm/firestream.c: In function ‘fs_open’:
drivers/atm/firestream.c:870: warning: ‘tmc0’ may be used uninitialized in this function
This indicates a real bug. We should check make_rate() return value for
potential errors.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>