The 8020i protocol (also 8070i and QIC-157) uses 12-byte commands;
shorter commands must be padded. Simon Detheridge reports that his
3-TB USB disk drive claims to use the 8020i protocol (which is
normally meant for ATAPI devices like CD drives), and because of its
large size, the disk drive requires the use of 16-byte commands.
However the usb_stor_pad12_command() routine in usb-storage always
sets the command length to 12, making the drive impossible to use.
Since the SFF-8020i specification allows for 16-byte commands in
future extensions, we may as well accept them. This patch (as1490)
changes usb_stor_pad12_command() to leave commands larger than 12
bytes alone rather than truncating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Simon Detheridge <simon@widgit.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch contains additional affected webcam models, on top of the
patches commited to linux-next 2394d67e44
and 5b253d88cc
Signed-off-by: sordna <sordna@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below are codes for accessing usb sysif_regs in driver:
usb_sys_regs = (struct usb_sys_interface *)
((u32)dr_regs + USB_DR_SYS_OFFSET);
these codes work in 32-bit, but in 64-bit, use u32 to type cast the address
of ioremap is not right, and accessing members of 'usb_sys_regs' will cause
call trace, so use (void *) for both 32-bit and 64-bit.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in commit aa6e52a35 we introduce the support of overcurrent notification
but the set and get of the power without checking if the gpio is valid or not
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a race between the USB disconnect handler and the TTY close
handler which may cause the acm object to be freed while it's still
being used. This may lead to things like
http://article.gmane.org/gmane.linux.usb.general/54250
and
https://lkml.org/lkml/2011/5/29/64
This is the simplest fix I could come up with. Holding on to open_mutex
while closing the TTY device prevents acm_disconnect() from freeing the
acm object between acm->port.count drops to 0 and the TTY side of the
cleanups are finalized.
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We've had another report of the "chipmunk" sound on a Logitech C600 webcam.
This patch resolves the issue.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current TT scheduling doesn't allow to play and then record on a
full-speed device connected to a high speed hub.
The IN iso stream can only start on the first uframe (0-2 for a 165 us)
because of CSPLIT transactions.
For the OUT iso stream there no such restriction. uframe 0-5 are possible.
The idea of this patch is that the first uframe are precious (for IN TT iso
stream) and we should allocate the last uframes first if possible.
For that we reverse the order of uframe allocation (last uframe first).
Here an example :
hid interrupt stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 125 | 39 | 0 | 0 | 0 | 0 | 0 |
----------------------------------------------------------------------
There no place for iso IN stream (uframe 0-2 are used) and we got "cannot
submit datapipe for urb 0, error -28: not enough bandwidth" error.
With the patch this become.
iso OUT stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 0 | 0 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
iso IN stream
----------------------------------------------------------------------
uframe | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
----------------------------------------------------------------------
max_tt_usecs | 125 | 125 | 125 | 125 | 125 | 125 | 30 | 0 |
----------------------------------------------------------------------
used usecs on a frame | 13 | 0 | 125 | 40 | 125 | 39 | 0 | 0 |
----------------------------------------------------------------------
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Signed-off-by: Thomas Poussevin <thomas.poussevin@parrot.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1494) fixes a problem in xhci-hcd's resume routine.
When the controller is runtime-resumed, this can only mean that one of
the two root hubs has made a wakeup request and therefore needs to be
resumed as well. Rather than try to determine which root hub requires
attention (which might be difficult in the case where a new
non-SuperSpeed device has been plugged in), the patch simply resumes
both root hubs.
Without this change, there is a race: The controller might be put back
to sleep before it can activate its IRQ line, and the wakeup condition
might never get handled.
The patch also simplifies the logic in xhci_resume a little, combining
some repeated flag settings into a single pair of statements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1491) works around a bug in GCC-3.4.6, which is still
supposed to be supported. The number of microseconds in the udelay()
call in quirk_usb_disable_ehci() is fixed at 100, but the compiler
doesn't understand this and generates a link-time error. So we
replace the otherwise unused variable "delta" with a simple constant
100. This same pattern is already used in other delay loops in that
source file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Konrad Rzepecki <krzepecki@dentonet.pl>
Tested-by: Konrad Rzepecki <krzepecki@dentonet.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for the usb serial ark3116 driver fixes an initialisation
ordering bug that gets triggered on hotplug when using at least recent
debian/ubuntu userspace. Without it, ark3116 serial cables don't work.
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Tested-by: law_ence.dev@ntlworld.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit de47725 (include: replace linux/module.h
with "struct module" wherever possible) introduced
a compilation breaked when it removed <linux/module.h>
from <linux/device.h> which musb glue layers were
(mistakenly) relying on.
Include that header to fix the compile error.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this the gadget will never be able to allocate a stream capable
endpoint. The manual says that the stream id is a 16bit id. It does not
talk about an upper limit in any other way. So I think 15 is a
reasonable limit :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
new endpoint should start from DATA0,
but mod_host didn't care it.
This patch fix it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renesas_usbhs is caring pipe type and its direction.
but current usbhs_endpoint_alloc() didn't check direction.
this patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit "193ab2a usb: gadget: allow multiple gadgets to be built"
the udc controllers can be compiled as a module. The ci13xxx_msm driver
is missing the MODULE_LICENSE statement, so loading fails with:
ci13xxx_msm: module license 'unspecified' taints kernel.
ci13xxx_msm: Unknown symbol dev_set_name (err 0)
ci13xxx_msm: Unknown symbol platform_get_irq (err 0)
ci13xxx_msm: Unknown symbol device_unregister (err 0)
ci13xxx_msm: Unknown symbol usb_add_gadget_udc (err 0)
ci13xxx_msm: Unknown symbol put_device (err 0)
ci13xxx_msm: Unknown symbol platform_driver_register (err 0)
ci13xxx_msm: Unknown symbol platform_get_resource (err 0)
ci13xxx_msm: Unknown symbol device_register (err 0)
ci13xxx_msm: Unknown symbol usb_del_gadget_udc (err 0)
This patch adds the missing MODULE_LICENSE statement with GPL v2 according
to the header of the driver.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following compile errors that show up if switching
on the debug trace code:
drivers/usb/gadget/ci13xxx_udc.c: In function 'ci13xxx_wakeup':
drivers/usb/gadget/ci13xxx_udc.c:2517:3: error: 'dev' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_udc.c:2517:3: note: each undeclared identifier is reported only once for each function it appears in
drivers/usb/gadget/ci13xxx_udc.c: In function 'udc_probe':
drivers/usb/gadget/ci13xxx_udc.c:2867:2: error: 'name' undeclared (first use in this function)
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The inline documentation of _gadget_stop_activity() states that the
function should be called holding the udc->lock. This however will
result in a deadlock, because _gadget_stop_activity() takes the udc->lock.
During normal operation _gadget_stop_activity() is always called unlocked,
but in ci13xxx_stop() it's called locked, this results in the following
deadlock during rmmod of a gadget driver.
This patch fixes the deadlock by calling _gadget_stop_activity() always
unlocked, the inline documentation is adjusted accordingly.
=============================================
[ INFO: possible recursive locking detected ]
3.1.0-rc6+ #159
---------------------------------------------
rmmod/121 is trying to acquire lock:
(udc_lock){-.-...}, at: [<c0229048>] _gadget_stop_activity+0x18/0x154
but task is already holding lock:
(udc_lock){-.-...}, at: [<c02291e0>] ci13xxx_stop+0x5c/0x164
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(udc_lock);
lock(udc_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by rmmod/121:
#0: (udc_lock#2){+.+.+.}, at: [<c02286c0>] usb_gadget_unregister_driver+0x34/0x88
#1: (udc_lock){-.-...}, at: [<c02291e0>] ci13xxx_stop+0x5c/0x164
stack backtrace:
[<c000d41c>] (unwind_backtrace+0x0/0xf0) from [<c0056f94>] (check_deadlock.clone.24+0x284/0x2c4)
[<c0056f94>] (check_deadlock.clone.24+0x284/0x2c4) from [<c00589ac>] (validate_chain.clone.25+0x430/0x6fc)
[<c00589ac>] (validate_chain.clone.25+0x430/0x6fc) from [<c0059bac>] (__lock_acquire+0x494/0x8f0)
[<c0059bac>] (__lock_acquire+0x494/0x8f0) from [<c005a698>] (lock_acquire+0x98/0x1a8)
[<c005a698>] (lock_acquire+0x98/0x1a8) from [<c02f12a4>] (_raw_spin_lock_irqsave+0x64/0xa0)
[<c02f12a4>] (_raw_spin_lock_irqsave+0x64/0xa0) from [<c0229048>] (_gadget_stop_activity+0x18/0x154)
[<c0229048>] (_gadget_stop_activity+0x18/0x154) from [<c0229234>] (ci13xxx_stop+0xb0/0x164)
[<c0229234>] (ci13xxx_stop+0xb0/0x164) from [<c022867c>] (usb_gadget_remove_driver+0x88/0x98)
[<c022867c>] (usb_gadget_remove_driver+0x88/0x98) from [<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88)
[<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88) from [<c0065f2c>] (sys_delete_module+0x1fc/0x26c)
[<c0065f2c>] (sys_delete_module+0x1fc/0x26c) from [<c00092a0>] (ret_fast_syscall+0x0/0x38)
BUG: spinlock lockup on CPU#0, rmmod/121, c05b1644
[<c000d41c>] (unwind_backtrace+0x0/0xf0) from [<c01da000>] (do_raw_spin_lock+0x128/0x144)
[<c01da000>] (do_raw_spin_lock+0x128/0x144) from [<c02f12c8>] (_raw_spin_lock_irqsave+0x88/0xa0)
[<c02f12c8>] (_raw_spin_lock_irqsave+0x88/0xa0) from [<c0229048>] (_gadget_stop_activity+0x18/0x154)
[<c0229048>] (_gadget_stop_activity+0x18/0x154) from [<c0229234>] (ci13xxx_stop+0xb0/0x164)
[<c0229234>] (ci13xxx_stop+0xb0/0x164) from [<c022867c>] (usb_gadget_remove_driver+0x88/0x98)
[<c022867c>] (usb_gadget_remove_driver+0x88/0x98) from [<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88)
[<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88) from [<c0065f2c>] (sys_delete_module+0x1fc/0x26c)
[<c0065f2c>] (sys_delete_module+0x1fc/0x26c) from [<c00092a0>] (ret_fast_syscall+0x0/0x38)
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current driver sets the request's dma addr (mReq->req.dma) to 0 to
mark the DMA address as not valid. However some gadget drivers
(e.g. gadgetfs) set the request's dma addr to DMA_ADDR_INVALID to mark
the address as invalid. This leads to bogus data send because the
ci13xxx_udc driver assumes the request has already been mapped.
This patch fixes the problem, by using DMA_ADDR_INVALID instead of 0
to mark the request's DMA address as invalid.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under certain circumstances lockdep finds an inconsistent lock state in
gadgetfs. The problem can be reproduced with a hardware using the
ci13xxx_udc driver and the gadgetfs test program (needs a patch to support
the ci13xxx_udc, though):
http://www.linux-usb.org/gadget/usb.c
Start the test program, wait to initialize, then press Ctrl+c.
This patch fixes the following problem by using spin_lock_irqsave()
instead of spin_lock().
=================================
[ INFO: inconsistent lock state ]
3.1.0-rc6+ #158
---------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
usb/113 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&dev->lock)->rlock){?.....}, at: [<bf000340>] gadgetfs_disconnect+0x14/0x80 [gadgetfs]
{IN-HARDIRQ-W} state was registered at:
[<c00596b8>] mark_irqflags+0x14c/0x1ac
[<c0059bf8>] __lock_acquire+0x4e0/0x8f0
[<c005a698>] lock_acquire+0x98/0x1a8
[<c02f10e0>] _raw_spin_lock+0x54/0x8c
[<bf000340>] gadgetfs_disconnect+0x14/0x80 [gadgetfs]
[<c0229104>] _gadget_stop_activity+0xd4/0x154
[<c022b130>] isr_reset_handler+0x34/0x1c0
[<c022c320>] udc_irq+0x204/0x228
[<c0069018>] handle_irq_event_percpu+0x64/0x3a0
[<c0069390>] handle_irq_event+0x3c/0x5c
[<c006ae5c>] handle_level_irq+0x8c/0x10c
[<c0068a34>] generic_handle_irq+0x30/0x44
[<c0009b2c>] handle_IRQ+0x30/0x84
[<c0008ef8>] __irq_svc+0x38/0x60
[<c0009c58>] default_idle+0x30/0x34
[<c0009e30>] cpu_idle+0x9c/0xd8
[<c04056f4>] start_kernel+0x278/0x2bc
irq event stamp: 6412
hardirqs last enabled at (6412): [<c02f1cd0>] _raw_spin_unlock_irqrestore+0x30/0x5c
hardirqs last disabled at (6411): [<c02f1278>] _raw_spin_lock_irqsave+0x20/0xa0
softirqs last enabled at (6381): [<c002833c>] irq_exit+0xa0/0xa8
softirqs last disabled at (6372): [<c002833c>] irq_exit+0xa0/0xa8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&dev->lock)->rlock);
<Interrupt>
lock(&(&dev->lock)->rlock);
*** DEADLOCK ***
1 lock held by usb/113:
#0: (udc_lock#2){+.+.+.}, at: [<c02286c0>] usb_gadget_unregister_driver+0x34/0x88
stack backtrace:
[<c000d41c>] (unwind_backtrace+0x0/0xf0) from [<c0058e98>] (print_usage_bug+0x144/0x1c4)
[<c0058e98>] (print_usage_bug+0x144/0x1c4) from [<c0059144>] (mark_lock_irq+0x22c/0x274)
[<c0059144>] (mark_lock_irq+0x22c/0x274) from [<c00592d4>] (mark_lock+0x148/0x3e0)
[<c00592d4>] (mark_lock+0x148/0x3e0) from [<c0059668>] (mark_irqflags+0xfc/0x1ac)
[<c0059668>] (mark_irqflags+0xfc/0x1ac) from [<c0059bf8>] (__lock_acquire+0x4e0/0x8f0)
[<c0059bf8>] (__lock_acquire+0x4e0/0x8f0) from [<c005a698>] (lock_acquire+0x98/0x1a8)
[<c005a698>] (lock_acquire+0x98/0x1a8) from [<c02f10e0>] (_raw_spin_lock+0x54/0x8c)
[<c02f10e0>] (_raw_spin_lock+0x54/0x8c) from [<bf000340>] (gadgetfs_disconnect+0x14/0x80 [gadgetfs])
[<bf000340>] (gadgetfs_disconnect+0x14/0x80 [gadgetfs]) from [<c0229104>] (_gadget_stop_activity+0xd4/0x154)
[<c0229104>] (_gadget_stop_activity+0xd4/0x154) from [<c0229240>] (ci13xxx_stop+0xbc/0x17c)
[<c0229240>] (ci13xxx_stop+0xbc/0x17c) from [<c022867c>] (usb_gadget_remove_driver+0x88/0x98)
[<c022867c>] (usb_gadget_remove_driver+0x88/0x98) from [<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88)
[<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88) from [<bf0003e8>] (dev_release+0x14/0x48 [gadgetfs])
[<bf0003e8>] (dev_release+0x14/0x48 [gadgetfs]) from [<c00cc158>] (__fput+0xa4/0x1f0)
[<c00cc158>] (__fput+0xa4/0x1f0) from [<c00c7f28>] (filp_close+0x5c/0x74)
[<c00c7f28>] (filp_close+0x5c/0x74) from [<c00c7fe8>] (sys_close+0xa8/0x150)
[<c00c7fe8>] (sys_close+0xa8/0x150) from [<c00092a0>] (ret_fast_syscall+0x0/0x38)
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The dynamic jack allocation of the MIDI gadget currently links all
external jacks to one single instance of an embedded jack. According to
the spec, this is only valid if these streams always carry the same data
stream, as described in the USB MIDI 1.0 spec, chapter 3.3.1.
Also, genius Windows 7(tm) terminates it's life cycle instantly with a
blue screen of death once a device with more than one input and output
port with the current implementation is connected.
While at it, and because it grew again by this change, allocate the
temporary function pointer list on the heap, not on the stack.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB-IF CV compliance tester is getting stricter, and it would
be valid for it to fail a mass-storage device that accepts an
invalid USB_BULK_RESET_REQUEST request. Although it doesn't do
that yet, let's be proactive and fix that now.
Suggested by Alan Stern.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The latest USB-IF CV tester checks for a valid length for this
request.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up the following section mismatch warnings:
WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0xf5d): Section
mismatch in reference from the function usbhs_mod_probe() to the function
.devinit.text:usbhs_mod_host_probe() The function usbhs_mod_probe() references
the function __devinit usbhs_mod_host_probe(). This is often because
usbhs_mod_probe lacks a __devinit annotation or the annotation of
usbhs_mod_host_probe is wrong.
WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0xfd7): Section
mismatch in reference from the function usbhs_mod_probe() to the function
.devexit.text:usbhs_mod_host_remove() The function usbhs_mod_probe() references
a function in an exit section. Often the function usbhs_mod_host_remove() has
valid usage outside the exit section and the fix is to remove the __devexit
annotation of usbhs_mod_host_remove.
WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0x1005): Section
mismatch in reference from the function usbhs_mod_remove() to the function
.devexit.text:usbhs_mod_host_remove() The function usbhs_mod_remove()
references a function in an exit section. Often the function
usbhs_mod_host_remove() has valid usage outside the exit section and the fix is
to remove the __devexit annotation of usbhs_mod_host_remove.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since renesas_usbhs mod_host didn't use
struct completion as static object, the warning of lockdep came out.
This patch fixup this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix compile error in file drivers/usb/gadget/fsl_udc_core.c.
drivers/usb/gadget/fsl_udc_core.c: In function 'portscx_device_speed':
drivers/usb/gadget/fsl_udc_core.c:1720: error: 'speed' undeclared (first
use in this function)
Introduced in commit e538dfdae8
(usb: Provide usb_speed_string() function)
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "BCLR" in CFIFOCTR/DnFIFOCTR can flush the fifo of "CPU side" only.
To flush the fifo of "SIE side", we have to use the "ACLRM" in PIPEnCTR.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The udc-newstyle needs device_register in probe() of platform_device.
If it doesn't call, kernel panic happens in the sysfs_create_dir() when
we run modprobe a gadget driver.
[ balbi@ti.com : fix compile warning introduced by this patch ]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those are simply giving information about the current
state of the UDC, nothing really fancy. We can let
everybody read those.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_gadget_disconnect() is responsible of removing
data pullups. Before doing that we must, first, tell
gadget driver we're disconnecting (by calling disconnect
method on gadget driver structure), unbind the gadget
driver and stop the controller.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
that has already being done by udc-core.c. It's
unnecessary and might cause issues with some gadget
drivers.
Tested: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should not be using dev_get_drvdata() because we
never call dev_set_drvdata(). Let's use container_of()
as all other sysfs attributes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of ra.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci:
usb, xhci: Clear warm reset change event during init
xhci: Set slot and ep0 flags for address command.
usb, xhci: fix lockdep warning on endpoint timeout
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. A companion
patch changes the PM core's behavior, but we also need to change the
USB core. In particular, this patch (as1493) updates the device's
last_busy time when an autosuspend fails, so that the PM core will
retry the autosuspend in the future when the delay time expires
again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
I noticed on my Panther Point system that I wasn't getting hotplug events
for my usb3.0 disk on a usb3 port. I tracked it down to the fact that the
system had the warm reset change bit still set. This seemed to block future
events from being received, including a hotplug event.
Clearing this bit during initialization allowed the hotplug event to be
received and the disk to be recognized correctly.
This patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
To fix this build error on ARM:
drivers/usb/host/xhci-hub.c: In function 'xhci_stop_device':
drivers/usb/host/xhci-hub.c:261: error: 'GFP_NOIO' undeclared (first use in this function)
make[4]: *** [drivers/usb/host/xhci-hub.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Use the lightweight version of the header that has just THIS_MODULE
and EXPORT_SYMBOL variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The situation up to this point meant that module.h was pretty
much everywhere, regardless of whether you asked for it or not.
We are fixing that, so give the USB folks who want it an actual
include of it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tomoya MORINAGA