Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.
I have tested the driver with my board, and it appears to work fine. With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power. With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power. I'm not drawing any current at the
moment, so this is reasonable. The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.
I didn't attempt to support changing any of the chip's settings or
enabling the FET. I'm not sure even how to do that and still fit within
the hwmon framework. :)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An hwmon driver for the National Semiconductor LM95241 triple temperature
sensors chip
Signed-off-by: Davide Rizzo <elpa-rizzo@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many thanks to Fujitsu Siemens Computers for providing docs and a
machine to test the driver on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.
If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.
At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update documentation to prevent further confusion/duplication.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) Fix CONFIG_DMI=n fallback to probe
hwmon: (abituguru3) Enable DMI probing feature on IN9 32X MAX
hwmon: (abituguru3) Match partial DMI board name strings
hwmon: Add a driver for the ADT7475 hardware monitoring chip
hwmon: (k8temp) Fix temperature reporting for (most) K8 RevG CPUs
hwmon: (k8temp) Fix wrong sensor selection for AMD K8 RevF/RevG CPUs
hwmon: (k8temp) Warn about fam F rev F errata
Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver. From a purely Linux developer's point of view,
the led and the accelerometer have nothing related. However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module. Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hwmon driver for the ADT7475 chip.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution. This patch extends the
LM70 driver to support the TMP121. The TMP123 differs in pin assign-
ment.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that the new merged fschmd driver has gained support for the watchdog
integrated into these IC's, there is no more reason to keep the old fscher
and fscpos drivers around, so mark them as deprecated.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for the watchdog part found in _all_ supported FSC
sensor chips.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add some documentation about the f71882fg driver, and update the Kconfig
documentation to report the new supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
New driver to play with. As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors. This driver has been tested on an IntelliStation Z30.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard"). It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.
This driver was first written by Yan Burman. Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now). Pavel Machek removed few more features and switched locking from
semaphore to mutex.
Several people have contributed to the database of the axes.
[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Yan Burman <burman.yan@gmail.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC. Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Driver based on corgi_ssp.c and sharpsl_pm.c, previously done by Richard
Purdie and many others.
Now changed to generic HWMON device and expose all the ADC input value
through sysfs.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a PIC16F747 based controller that monitors and consolidates
the hardware access to various fan and temperature values reported by
adr7462 and similar devices behind an I2C bus.
Signed-off-by: David S. Miller <davem@davemloft.net>
SPI driver for analog to digital converters national semiconductor
ADC081S101, ADC124S501, ...
Code for 8 channels by Tobias Himmer.
This driver adds support for National Semiconductor ADC<bb><c>S<sss> chip
family, where:
* bb is the resolution in number of bits (8, 10, 12)
* c is the number of channels (1, 2, 4, 8)
* sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
kSPS and 101 for 1 MSPS)
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Cc: Tobias Himmer <tobias@himmer-online.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver for the Analog Devices AD7414 temperature monitoring chip.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The adm9240 driver is in the kernel for three years now, time to
remove the EXPERIMENTAL dependency.
Signed-off-by: Grant Coady <gcoady.lk@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
and can't be programmed to fully turn off
- Different voltage scaling
- No VID input
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
More LM75 updates:
- Teach the LM75 driver to use new-style driver binding:
* Create a second driver struct, using new-style driver binding
methods cribbed from the legacy code.
* Add a MODULE_DEVICE_TABLE (for "newER-style binding")
* The legacy probe logic delegates its work to this new code.
* The legacy driver now uses the name "lm75_legacy".
- More careful initialization. Chips are put into 9-bit mode so
the current interconversion routines will never fail.
- Save the original chip configuration, and restore it on exit.
(Among other things, this normally turns off the mode where
the chip is constantly sampling ... and thus saves power.)
So the new-style code should catch all chips that boards declare,
while the legacy code catches others. This particular coexistence
strategy may need some work yet ... legacy modes might best be set
up explicitly by some tool not unlike "sensors-detect". (Or else
completely eradicated...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Minor cleanup and reorg of the lm75 code.
- Kconfig provides a larger list of lm75-compatible chips
- A top comment now says what the driver does (!) ... as in, just
what sort of sensor is this??
- Section comments now delineate the various sections of the driver:
hwmon attributes, driver binding, register access, module glue.
One driver binding function moved out of the attribute section,
as did the driver struct itself.
- Minor tweaks to legacy probe logic: correct a comment, and
remove a pointless variable.
- Whitespace, linelength, and comment fixes.
This patch should include no functional changes. It's preparation
for adding new-style (driver model) I2C driver binding.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This driver reads IBM Active Energy Manager energy/temperature/power
sensors on IBM System X hardware.
[akpm@linux-foundation.org: fix printk warnings]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enhanced the list of supported machines.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Steve Hardy <steve@linuxrealtime.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The W83627HF hardware monitoring features are supported by the
w83627hf driver for several years now. Support by the w83781d has
been advertised as deprecated 6 months ago, it's about time to see
it go.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
It happens that the Analog Devices ADM1024 is fully compatible with
the National Semiconductor LM87, so support for the former can easily
be added to the lm87 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
New driver to read FB-DIMM temperature sensors on systems with the
Intel 5000 series chipsets.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: use full RCU API
Input: remove tsdev interface
Input: add support for Blackfin BF54x Keypad controller
Input: appletouch - another fix for idle reset logic
HWMON: hdaps - switch to using input-polldev
Input: add support for SEGA Dreamcast keyboard
Input: omap-keyboard - don't pretend we support changing keymap
Input: lifebook - fix X and Y axis range
Input: usbtouchscreen - add support for GeneralTouch devices
Input: fix open count handling in input interfaces
Input: keyboard - add CapsShift lock
Input: adbhid - produce all CapsLock key events
Input: ALPS - add signature for ThinkPad R61
Input: jornada720_kbd - send MSC_SCAN events
Input: add support for the HP Jornada 7xx (710/720/728) touchscreen
Input: add support for HP Jornada 7xx onboard keyboard
Input: add support for HP Jornada onboard keyboard (HP6XX)
Input: ucb1400_ts - use schedule_timeout_uninterruptible
Input: xpad - fix dependancy on LEDS class
Input: auto-select INPUT for MAC_EMUMOUSEBTN option
...
Resolved conflicts manually in drivers/hwmon/applesmc.c: converting from
a class device to a device and converting to use input-polldev created a
few apparently trivial clashes..
Switch to using input-polldev skeleton instead of implementing polling loop
by itself. This also fixes problem with trylock on a mutex in atomic
context.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a new merged driver for FSC sensor chips, it merges the fscher
and fscpos drivers and adds support for the FSC Scylla, Heracles and Heimdall
chips.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for the SMSC SCH3112, SCH3114, and SCH3116 Super-I/O
chips. These chips feature identical hardware monitoring capabilites with the
expection that some of the fan inputs and pmw outputs don't exist.
The hardware monitoring features of the SCH311x chips can only be accessed via
the ISA bus. The driver therefore registers as a platform driver, if such a
chip is detected.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add a driver to export IBM PowerExecutive power meter sensors.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Drop HWMON from the dependency list of ABITUGURU3 and LM93: this is
now handled at menu level.
* Make the Abit, Asus and FSC chip drivers depend on X86. These are
custom chips which can only be found on their respective manufacturer's
systems, and these manufacturers only do x86 hardware AFAIK.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add support for Fintek F75375S/SP and F75373.
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
New driver to expose temperature and fan controls attached to Analog
Devices ADT7470 hwmon chips.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This is the second version of a new driver for the hardware monitoring features
of the Fintek F71882FG and F71883FG Super-I/O chips. This version has several
small fixes for flaws discovered during the review of the first version.
This version of the driver does not support the pwm part of these chips (yet).
I'll first design a sysfs api for this and post that for discussion, and then
implement pwm support as an incremental patch over this one.
This driver supports all sensors of this chip, except for the vid inputs. The
vid inputs are somewhat documented in the datasheet, but I know nothing about
vid/vrm stuff. Help with this would be much appreciated.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The Fintek F71806F/FG is compatible with the F71872F/FG, so it is
already supported by the f71805f hardware monitoring driver. In fact,
both chips have the same chip ID, so the driver can't even
differentiate between them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Switch to using input-polldev skeleton instead of implementing polling
loop by itself.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Switch to using input-polldev skeleton instead of implementing polling loop by
itself. This also fixes problem with trylock on a mutex in atomic context.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
