md arrays are not currently destroyed when they are stopped - they
remain in /sys/block. Last time I tried this I tripped over locking
too much.
A consequence of this is that udev doesn't remove anything from /dev.
This is rather ugly.
As an interim measure until proper device removal can be achieved,
make sure all partitions are removed using the BLKRRPART ioctl, and
send a KOBJ_CHANGE when an md array is stopped.
Signed-off-by: NeilBrown <neilb@suse.de>
Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I had assumed that the standard recovery would be sufficient for this
hardware but it isn't. Fix up the other registers on resume as needed. See
bug #11735
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[http://lkml.org/lkml/2008/10/18/82]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed. These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to request posting limitations, bandwidth of sil3132 is limited to
around 120MB/s with the minimum pci-e payload size (128bytes) which is
used by most consumer systems. However, write throughput can be
slightly (~3%) increased by increasing the max read requeset size.
Configure it to 4k which is the maximum supported. This optimization
is also done by SIMG's windows driver.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix libata missing kernel-doc:
Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description
found for parameter 'tag'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.
* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()
While at it, reformat comments in cable_is_40wire().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add an appropriate entry for the Promise PDC42819 controller. It has an
AHCI mode and so far works correctly with board_ahci.
This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port)
software-based RAID cards (for which there is a binary driver, t3sas) and
can be found on some motherboards, for example the MSI K9A2 Platinum,
which calls the chip a Promise T3 controller.
Although this controller also supports SAS devices, its default bootup mode
is AHCI and the binary driver has to do some magic to get the chip into the
appropriate mode to drive SAS disks.
Seeing as no documentation is provided by Promise, adding this entry to the
ahci driver allows the controller to be useful to people as a SATA
controller (with no ill effects on the system if a SAS disk is connected -
probing of the port just times out with "link online but device
misclassified"), without having to resort to using the binary driver. Users
who require SAS or the proprietary software raid can get this functionality
using the binary driver.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix fastpath issues
Since mmci_request() can be called from a non-interrupt
context, and does, during kernel init, causing a host
of debug messages during boot if you enable spinlock debugging,
we need to use the spinlock calls that save IRQ flags and
restore them.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix mac80211.h kernel-doc: it had some extra parameters that were
no longer valid and incorrect format for a return value in 2 places.
Warning(lin2628-rc2//include/net/mac80211.h:1487): Excess function parameter or struct member 'control' description in 'ieee80211_beacon_get'
Warning(lin2628-rc2//include/net/mac80211.h:1596): Excess function parameter or struct member 'control' description in 'ieee80211_get_buffered_bc'
Warning(lin2628-rc2//include/net/mac80211.h:1632): Excess function parameter or struct member 'rc4key' description in 'ieee80211_get_tkip_key'
Warning(lin2628-rc2//include/net/mac80211.h:1735): Excess function parameter or struct member 'return' description in 'ieee80211_start_tx_ba_session'
Warning(lin2628-rc2//include/net/mac80211.h:1775): Excess function parameter or struct member 'return' description in 'ieee80211_stop_tx_ba_session'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Saturday 25 October 2008 10:24:10 Johannes Berg wrote:
> just FYI in case you haven't seen them. the p54 one looks like a genuine
> problem.
>
> drivers/net/wireless/p54/p54common.c: In function ‘p54_parse_eeprom’:
> drivers/net/wireless/p54/p54common.c:325: warning: ‘synth’ may be used uninitialized in this function
There you go. Yes, it is a genuine problem, if the device's eeprom is screwed really up.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a s2ram / resume cycle, resetting the key cache does not work
unless it is deferred until after the hardware has been reinitialised by
a call to ath5k_hw_reset(). This fixes a regression introduced by
"ath5k: fix suspend-related oops on rmmod".
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialise correctly last fields, so tasks can be actually executed.
On some architectures the initial jiffies value is not zero, so later
all rfkill incorrectly decides that rfkill_*.last is in future.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a double-free error in p54pci
( http://bugzilla.kernel.org/show_bug.cgi?id=11782 )
Trying to free already-free IRQ 10
Pid: 108, comm: pccardd Not tainted 2.6.27-05577-g0cfd810-dirty #1
Call Trace:
[<c01265dc>] free_irq+0xad/0xb9
[<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7
[<c01ba8e6>] p54p_stop+0x4a/0x1fa
[<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7
[<c02348c5>] p54p_probe+0x23e/0x302
Tested-by: Sean Young
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement set_mac_address for runtime mac address change.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch corrects a message bug in the via-velocity driver which
bothered me for some time.
The messages printed during device init look like the following:
[ 8.486422] eth%d: set value of parameter Wake On Lan options to 0
^^!
[ 8.487340] eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
Note the unresolved format string.
dev->name is unavailable before register_netdev, so use
dev_driver_string(&pdev->dev), which is also consistent with other
drivers.
"char *devname" parameters had to be converted to "const char *devname" to
be consistent with dev_driver_string return value.
Signed-off-by: Sven Hartge <sven@svenhartge.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The recent build fix for ibm_newemac has a typo in the config
option #ifdef used for disabling flow control. This corrects
it to the proper Kconfig option name.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
All kernel memory which is used for kernel/hardware data transfer must
be registered with firmware using "memory regions". 16GB hugepages
may not be part of a memory region due to firmware restrictions.
This patch modifies the walk_memory_resource callback fn to filter
hugepages and add only standard memory to the busmap which is later
on used for MR registration.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to check the address that pci_alloc_consistent() returns since
it might fail.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To make the qeth driver more robust in case of malformatted inbound
packets due to hardware problems, an additional check for
OSN-card-type is added for OSN-type packets.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Removing this check improves usability because you do not have to
set the device online to initially set ipv6 routing option.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For the non preallocated qeth header code path we should not
change the header length.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
IP-threads have been removed from the qeth driver. Only the
recover-thread is left over. This makes checkings for
non-recover threads superfluous.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
libata: fix NCQ devices behind port multipliers
scsi: make sure that scsi_init_shared_tag_map() doesn't overwrite existing map
For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Right now callers have to check whether scsi_host->bqt is already
set up, it's much cleaner to just have scsi_init_shared_tag_map()
does this check on its own.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Impact: documentation fix
sched-design-CFS.txt wrongly references sched_granularity_ns sysctl,
as its name in fact is sched_min_granularity_ns.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Blackfin: update SPORT0 port selector (v2)
ALSA: hda - Restore default pin configs for realtek codecs
sound: use a common working email address
pci: use pci_ioremap_bar() in sound/
When booting Linux on a txx9 board with VxWorks boot loader, it crashes in
prom_getenv(), as VxWorks doesn't pass firmware parameters in a0-a3 (in my
case, the actual leftover values in these registers were 0x80002000,
0x80001fe0, 0x2000, and 0x20).
Make the parsing of argc, argv, and envp a bit more robust by checking if
argc is a number below CKSEG0, and argv/envp point to CKSEG0.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove runtime db_* macros as we don't need them any more. In general,
such helpers are useful for initial porting, but once approved, they are
not indispensable.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current EMMA2RH irq code is mess. Before cleaning it up, gather them
in one place as a first step.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We'll put all EMMA related headers there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
git mv arch/mips/{emma2rh,emma} and fixups Makefiles. We'll put all NEC
EMMA series based machines there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
NeilBrown