Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ar9170 to load firmware asynchronously
out of ->probe() and only register with mac80211 when
all firmware has been loaded successfully. If, on the
other hand, any firmware fails to load, it will now
unbind from the device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While ath9k does not support RIFS yet, the ability to receive RIFS
frames is currently enabled for most chipsets in the initvals.
This is causing baseband related issues on AR9160 and AR9130 based
chipsets, which can lock up under certain conditions.
This patch fixes these issues by overriding the initvals, effectively
disabling RIFS for all affected chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ath9k to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ar9170 to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In AP mode, ath_beacon_config_ap only restarts the timer if a TSF
restart is requested. Apparently this was added, because this function
unconditionally sets the flag for TSF reset.
The problem with this is, that ath9k_hw_reset() clobbers the timer
registers (specified in the initvals), thus effectively disabling the
SWBA interrupt whenever a card reset without TSF reset is issued
(happens in a few places in the code).
This patch fixes ath_beacon_config_ap to only issue the TSF reset flag
when necessary, but reinitialize the timer unconditionally. Tests show,
that this is enough to keep the SWBA interrupt going after a call to
ath_reset()
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When selecting the tx fallback rate, rc.c used a separate variable
'nrix' for storing the next rate index, however it did not use that as
reference for further rate index lowering. Because of that, it ended up
reusing the same rate for multiple multi-rate retry stages, thus
decreasing delivery probability under changing link conditions.
This patch removes the separate (unnecessary) variable and fixes
fallback the way it was intended to work.
This should result in increased throughput and better link stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the lowest rate for Beacon frames, use the rate
index specified in the mac80211 TX info in AP mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support for setting the coverage class in some cases broke
association and data transfer, as it overwrote the initial ACK timeout
value from the initvals with a smaller value.
I don't know why the new value works in 5 GHz (matches the initval
there), but not in 2.4 GHz (initvals use 64us here), so until the
problem is fully understood, the value should be increased again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware needs to know what type of frames are being
sent in order to fill in various fields, for example the
timestamp in probe responses (before this patch, it was
always 0). Set it correctly when initializing the TX
descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a WARN_ON which is triggered
by Poland's country code.
ath: EEPROM regdomain: 0x8268
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x37
ath: Country alpha2 being used: PL
ath: Regpair used: 0x37
-----------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/regd.c:155 ath_regd_init+0x30b
Pid: 12661, comm: firmware/carl91 2.6.33-rc5-wl #18
Call Trace:
[<>] ? warn_slowpath_common+0x76/0x8c
[<>] ? ar9170_reg_notifier+0x0/0x2d [carl9170usb]
[<>] ? ath_regd_init+0x30b/0x377 [ath]
[<>] ? ar9170_register+0x3b3/0x3ca [carl9170usb]
[...]
---[ end trace ]---
Note: Poland is just an example. But it is very likely
that more country codes are affected.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_tx_stats() will be removed from mac80211.
Because ar9170 uses ieee80211_tx_queue_stats internally, create a new
identical struct ar9170_tx_queue_stats which the driver can use.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If split tkip key is used, ath_delete_key should delete
rx key and rx mic key. This patch fixes the leak of hw
keycache in the case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM timer interrupt is enabled even before the ACK of nullqos
is received which is unnecessary.
Also clean up the CONF_PS part of config callback properly for
better readability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
beacons configuration SHOULD be done only if the STA is associated.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some single chip family devices are sold in the market with
802.11n bonded out, these have no hardware capability for
802.11n but ath9k can still support them. These are called
AR2427.
Cc: stable@kernel.org
Reported-by: Rolf Leggewie <bugzilla.kernel.org@rolf.leggewie.biz>
Tested-by: Bernhard Reiter <ockham@raz.or.at>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling ath_bus_cleanup() after ieee80211_free_hw() resulted in access
to common->bus_ops, which is already freed as part of the device data.
Remove the cleanup field in struct ath_bus_ops, as it was never used
properly. Remove ath_bus_cleanup(). Merge cleanup functions in place
of the ath_bus_cleanup() calls. Take care not to use any device data
after ieee80211_free_hw().
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using stack for that causes warnings with CONFIG_FRAME_WARN=1024
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Numeric channel is hard to get, so it won't be printed. Replace Mhz
with MHz on the affected lines and add commas as needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IDLE PS (Full Sleep) doesn't work when ifconfig up
is done during Idle unassociated state.
Fix this by restoring FULL SLEEP in ps_restore if CONF_IDLE
is set.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With following patch, LED should now work with LiteOn AR5BXB63 mini
pci-e cards.
(Broken patch fixed-up by me...let's hope I did it right! -- JWL)
Signed-off-by: Luca Verdesca <magooz@salug.it>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k currently forces hw->max_rate_tries to 4 to work around rate
control inefficiencies. This has some negative side effects, such as
rate_control_send_low also using a maximum of 4 tries, which could
negatively affect reliability of unicast management frames.
This patch pushes the retry limit to the rate control instead, and
allows it to use more tries on the last stage to prevent unnecessary
packet loss.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Among other changes, this commit:
commit 06d0f0663e
Author: Sujith <Sujith.Manoharan@atheros.com>
Date: Thu Feb 12 10:06:45 2009 +0530
ath9k: Enable Fractional N mode
changed the hw attach code to fix up initialization values only for
dual band devices, however the commit message did not give a reason as
to why this would be useful or necessary.
According to tests by Jorge Boncompte, this breaks at least some
2GHz-only cards, so the code should be changed back to the
unconditional INI fixup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Jorge Boncompte <jorge@dti2.net>
Cc: stable@kernel.org
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As all bt packets are priority traffic during bt scan, wifi
will get disconnected when bt scan lasts for few seconds. Fix
this by allocating 10% of bt period time (4.5ms) to wifi fully.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon sent gating doesn't seem to work with any combination
of flags. Thus, buffered frames tend to stay buffered forever,
using up tx descriptors.
Instead, use the DBA gating and hold transmission of the buffered
frames until 80% of the beacon interval has elapsed using the ready
time. This fixes the following error in AP mode:
ath5k phy0: no further txbuf available, dropping packet
Add a comment to acknowledge that this isn't the best solution.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using the external sleep clock in AP mode, the
TSF increments too quickly, causing beacon interval
to be much lower than it is supposed to be, resulting
in lots of beacon-not-ready interrupts.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14802.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cleaning up beacon buffers and slots, ath9k currently checks if
sc->ah->opmode is set to a beacon related mode before cleaning up
buffers.
An unfortunate ordering of interface up/down commands can lead to
sc->ah->opmode being set to monitor mode, while there are AP interfaces
present on the same wiphy.
Always cleaning up beacon buffers if present fixes this issue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users wishing to tweak tx power want it to happen immediately,
try to respect that. This was tested by Lorenzo by measuring the
received signal strength from an AP with ath9k and the patch.
Changing the tx power on the AP produced these results:
1) iwconfig wlan0 txpower 20 ---> Rx power -37dbm
2) iwconfig wlan0 txpower 15 ---> Rx power -41dbm
3) iwconfig wlan0 txpower 10 ---> Rx power -45dbm
4) iwconfig wlan0 txpower 5 ---> Rx power -51dbm
5) iwconfig wlan0 txpower 0 ---> Rx power -37dbm
The result with 0 is an anomoly and would need to be
addressed through a separate patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Tx DMA descriptor has two kinds of flags that select RTS/CTS usage.
The first one (global for the frame) selects whether RTS/CTS or
CTS-to-self should be used, the second one enables RTS/CTS or
CTS-to-self usage for an individual multi-rate-retry entry.
Previously the code preparing the descriptor only enabled the global
flag, if the first MRR series selected the local one.
Fix this by enabling the global flag if any of the MRR entries need it.
With this patch, rate control can properly select the use of RTS/CTS
for all MRR entries except the first one, which is the default behavior.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously ath9k left the initialization of slot timing and ACK/CTS
timeout to the mode specific initvals. This does not handle short vs
long slot in 2.4 GHz and uses a rather strange value for the 2.4 GHz
ACK timeout (64 usec).
This patch uses the proper ath9k_hw functions for setting slot time and
timeouts and also implements the switch between short and long slot
time in 2.4 GHz
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device has to be marked as invalid before
registering the ISR. HW initialization takes place
after the ISR has been registered, and the invalid
flag is eventually cleared in the ->stop() callback.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 passes appropriate flags indicating whether
monitor mode is being used. Use this to set the HW opmode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file can be used to track frame reception errors.
PHY error counts are also added.
Location: ath9k/phy#/recv
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
