From: Bruce Ashfield <bruce.ashfield@windriver.com>
To fully support the armv7-a instruction set/optimizations, support
for the R_ARM_MOVW_ABS_NC and R_ARM_MOVT_ABS relocation types is
required.
The MOVW and MOVT are both load-immediate instructions, MOVW loads 16
bits into the bottom half of a register, and MOVT loads 16 bits into the
top half of a register.
The relocation information for these instructions has a full 32 bit
value, plus an addend which is stored in the 16 immediate bits in the
instruction itself. The immediate bits in the instruction are not
contiguous (the register # splits it into a 4 bit and 12 bit value),
so the addend has to be extracted accordingly and added to the value.
The value is then split and put into the instruction; a MOVW uses the
bottom 16 bits of the value, and a MOVT uses the top 16 bits.
Signed-off-by: David Borman <david.borman@windriver.com>
Signed-off-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add power management support to the VIC by registering
each VIC as a system device to get suspend/resume
events going.
Since the VIC registeration is done early, we need to
record the VICs in a static array which is used to add
the system devices later once the initcalls are run. This
means there is now a configuration value for the number
of VICs in the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In the long run, we may want to place page tables in highmem. However,
pmd_page() has traditionally been coded to convert the physical address
to a virtual one, which won't work with highmem pages. Instead,
translate the physical address to a PFN, and then convert the PFN to a
struct page instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel 2.6.30-rc1 added sys_preadv and sys_pwritev to most archs
but not ARM, resulting in
<stdin>:1421:2: warning: #warning syscall preadv not implemented
<stdin>:1425:2: warning: #warning syscall pwritev not implemented
This patch adds sys_preadv and sys_pwritev to ARM.
These syscalls simply take five long-sized parameters, so they
should have no calling-convention/ABI issues in the kernel.
Tested on armv5tel eabi using a preadv/pwritev test program posted
on linuxppc-dev earlier this month.
It would be nice to get this into the kernel before 2.6.30 final,
so that glibc's kernel version feature test for these syscalls
doesn't have to special-case ARM.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When unmapping N pages (e.g. shared memory) the amount of TLB flushes
done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it should be N at
maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8 pages, so there is a
noticeable performance penalty when unmapping a large VMA and the system
is spending its time in flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh Dickins,
and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger mappings
even more.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds a SZ_32K define to the available sizes. I need it for an
upcoming platform support.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.
Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds support for Faraday FA526 core. This core is used at least by:
Cortina Systems Gemini and Centroid family
Cavium Networks ECONA family
Grain Media GM8120
Pixelplus ImageARM
Prolific PL-1029
Faraday IP evaluation boards
v2:
- move TLB_BTB to separate patch
- update copyrights
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Now, as all places that use Scoop GPIO have been converted to use
GPIO API, drop old-style accessors completely.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"""The Marvell® PXA168 processor is the first in a family of application
processors targeted at mass market opportunities in computing and consumer
devices. It balances high computing and multimedia performance with low
power consumption to support extended battery life, and includes a wealth
of integrated peripherals to reduce overall BOM cost .... """
See http://www.marvell.com/featured/pxa168.jsp for more information.
1. Marvell Mohawk core is a hybrid of xscale3 and its own ARM core,
there are many enhancements like instructions for flushing the
whole D-cache, and so on
2. Clock reuses Russell's common clkdev, and added the basic support
for UART1/2.
3. Devices are a bit different from the 'mach-pxa' way, the platform
devices are now dynamically allocated only when necessary (i.e.
when pxa_register_device() is called). Description for each device
are stored in an array of 'struct pxa_device_desc'. Now that:
a. this array of device description is marked with __initdata and
can be freed up system is fully up
b. which means board code has to add all needed devices early in
his initializing function
c. platform specific data can now be marked as __initdata since
they are allocated and copied by platform_device_add_data()
4. only the basic UART1/2/3 are added, more devices will come later.
Signed-off-by: Jason Chagas <chagas@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
It would seem when building kernel modules with modern binutils
(required by modern GCC) for ARM v4T targets (specifically observed
with the Samsung 24xx SoC which is an 920T) R_ARM_V4BX relocations
are emitted for function epilogues.
This manifests at module load time with an "unknown relocation: 40"
error message.
The following patch adds the R_ARM_V4BX relocation to the ARM kernel
module loader. The relocation operation is taken from that within the
binutils bfd library.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Map unused registers at the end of DMA region at 64 MB to allow PCI masters
to cross the boundary when prefetching data from SDRAM.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
The choice is between looping over the physical range and performing
single cache line operations, or to map highmem pages somewhere, as
cache range ops are possible only on virtual addresses.
Because L2 range ops are much faster, we go with the later by factoring
the physical-to-virtual address conversion and use a fixmap entry for it
in the HIGHMEM case.
Possible future optimizations to avoid the pte setup cost:
- do the pte setup for highmem pages only
- determine a threshold for doing a line-by-line processing on physical
addresses when the range is small
Signed-off-by: Nicolas Pitre <nico@marvell.com>
If a machine class has a custom __virt_to_bus() implementation then it
must provide a __arch_page_to_dma() implementation as well which is
_not_ based on page_address() to support highmem.
This patch fixes existing __arch_page_to_dma() and provide a default
implementation otherwise. The default implementation for highmem is
based on __pfn_to_bus() which is defined only when no custom
__virt_to_bus() is provided by the machine class.
That leaves only ebsa110 and footbridge which cannot support highmem
until they provide their own __arch_page_to_dma() implementation.
But highmem support on those legacy platforms with limited memory is
certainly not a priority.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This is a helper to be used by the DMA mapping API to handle cache
maintenance for memory identified by a page structure instead of a
virtual address. Those pages may or may not be highmem pages, and
when they're highmem pages, they may or may not be virtually mapped.
When they're not mapped then there is no L1 cache to worry about. But
even in that case the L2 cache must be processed since unmapped highmem
pages can still be L2 cached.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The kmap virtual area borrows a 2MB range at the top of the 16MB area
below PAGE_OFFSET currently reserved for kernel modules and/or the
XIP kernel. This 2MB corresponds to the range covered by 2 consecutive
second-level page tables, or a single pmd entry as seen by the Linux
page table abstraction. Because XIP kernels are unlikely to be seen
on systems needing highmem support, there shouldn't be any shortage of
VM space for modules (14 MB for modules is still way more than twice the
typical usage).
Because the virtual mapping of highmem pages can go away at any moment
after kunmap() is called on them, we need to bypass the delayed cache
flushing provided by flush_dcache_page() in that case.
The atomic kmap versions are based on fixmaps, and
__cpuc_flush_dcache_page() is used directly in that case.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This is the minimum fixmap interface expected to be implemented by
architectures supporting highmem.
We have a second level page table already allocated and covering
0xfff00000-0xffffffff because the exception vector page is located
at 0xffff0000, and various cache tricks already use some entries above
0xffff0000. Therefore the PTEs covering 0xfff00000-0xfffeffff are free
to be used.
However the XScale cache flushing code already uses virtual addresses
between 0xfffe0000 and 0xfffeffff.
So this reserves the 0xfff00000-0xfffdffff range for fixmap stuff.
The Documentation/arm/memory.txt information is updated accordingly,
including the information about the actual top of DMA memory mapping
region which didn't match the code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds a Non-cacheable Normal ARM executable memory type,
MT_MEMORY_NONCACHED.
On OMAP3, this is used for rapid dynamic voltage/frequency scaling in
the VDD2 voltage domain. OMAP3's SDRAM controller (SDRC) is in the
VDD2 voltage domain, and its clock frequency must change along with
voltage. The SDRC clock change code cannot run from SDRAM itself,
since SDRAM accesses are paused during the clock change. So the
current implementation of the DVFS code executes from OMAP on-chip
SRAM, aka "OCM RAM."
If the OCM RAM pages are marked as Cacheable, the ARM cache controller
will attempt to flush dirty cache lines to the SDRC, so it can fill
those lines with OCM RAM instruction code. The problem is that the
SDRC is paused during DVFS, and so any SDRAM access causes the ARM MPU
subsystem to hang.
TI's original solution to this problem was to mark the OCM RAM
sections as Strongly Ordered memory, thus preventing caching. This is
overkill: since the memory is marked as non-bufferable, OCM RAM writes
become needlessly slow. The idea of "Strongly Ordered SRAM" is also
conceptually disturbing. Previous LAKML list discussion is here:
http://www.spinics.net/lists/arm-kernel/msg54312.html
This memory type MT_MEMORY_NONCACHED is used for OCM RAM by a future
patch.
Cc: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point these being in a generic include file when they're
only used in arch/arm/mach-rpc/dma.c.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds ELF section parsing for the unwinding tables in loadable
modules together with the PREL31 relocation symbol resolving.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the main functionality for parsing the stack unwinding
information generated by the ARM EABI toolchains. The unwinding
information consists of an index with a pair of words per function and a
table with unwinding instructions. For more information, see "Exception
Handling ABI for the ARM Architecture" at:
http://infocenter.arm.com/help/topic/com.arm.doc.subset.swdev.abi/index.html
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the walk_stacktrace and its callers for easier
integration of stack unwinding. The arch/arm/kernel/stacktrace.h file is
also moved to arch/arm/include/asm/stacktrace.h.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves code around in the arch/arm/kernel/traps.c file for
easier integration of the stack unwinding support.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The VFPv3D16 is a VFPv3 CPU configuration where only 16 double registers
are present, as the VFPv2 configuration. This patch adds the
corresponding hwcap bits so that applications or debuggers have more
information about the supported features.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds ptrace support for setting and getting the VFP registers
using PTRACE_SETVFPREGS and PTRACE_GETVFPREGS. The user_vfp structure
defined in asm/user.h contains 32 double registers (to cover VFPv3 and
Neon hardware) and the FPSCR register.
Cc: Paul Brook <paul@codesourcery.com>
Cc: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make headers_check' warnings:
usr/include/asm-arm/swab.h:19: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-arm/swab.h:25: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-arm/setup.h:17: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-arm/setup.h:25: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-arm/a.out.h:5: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-arm/a.out.h:9: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Add swab.h to kbuild.asm and remove the individual entries from
each arch, mark as unifdef as some arches have some kernel-only
bits inside.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make VMAs per mm_struct as for MMU-mode linux. This solves two problems:
(1) In SYSV SHM where nattch for a segment does not reflect the number of
shmat's (and forks) done.
(2) In mmap() where the VMA's vm_mm is set to point to the parent mm by an
exec'ing process when VM_EXECUTABLE is specified, regardless of the fact
that a VMA might be shared and already have its vm_mm assigned to another
process or a dead process.
A new struct (vm_region) is introduced to track a mapped region and to remember
the circumstances under which it may be shared and the vm_list_struct structure
is discarded as it's no longer required.
This patch makes the following additional changes:
(1) Regions are now allocated with alloc_pages() rather than kmalloc() and
with no recourse to __GFP_COMP, so the pages are not composite. Instead,
each page has a reference on it held by the region. Anything else that is
interested in such a page will have to get a reference on it to retain it.
When the pages are released due to unmapping, each page is passed to
put_page() and will be freed when the page usage count reaches zero.
(2) Excess pages are trimmed after an allocation as the allocation must be
made as a power-of-2 quantity of pages.
(3) VMAs are added to the parent MM's R/B tree and mmap lists. As an MM may
end up with overlapping VMAs within the tree, the VMA struct address is
appended to the sort key.
(4) Non-anonymous VMAs are now added to the backing inode's prio list.
(5) Holes may be punched in anonymous VMAs with munmap(), releasing parts of
the backing region. The VMA and region structs will be split if
necessary.
(6) sys_shmdt() only releases one attachment to a SYSV IPC shared memory
segment instead of all the attachments at that addresss. Multiple
shmat()'s return the same address under NOMMU-mode instead of different
virtual addresses as under MMU-mode.
(7) Core dumping for ELF-FDPIC requires fewer exceptions for NOMMU-mode.
(8) /proc/maps is now the global list of mapped regions, and may list bits
that aren't actually mapped anywhere.
(9) /proc/meminfo gains a line (tagged "MmapCopy") that indicates the amount
of RAM currently allocated by mmap to hold mappable regions that can't be
mapped directly. These are copies of the backing device or file if not
anonymous.
These changes make NOMMU mode more similar to MMU mode. The downside is that
NOMMU mode requires some extra memory to track things over NOMMU without this
patch (VMAs are no longer shared, and there are now region structs).
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original arch/arm/include/asm/hardware/vic.h was
written for the PL190 ARM VIC implementation, and as
such does not have any information about the PL192
version.
Add details about the PL192 and PL190 specific registers
and any changes between the two units.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
dma_supported() is supposed to indicate whether the system can support
the DMA mask it was passed, which depends on the maximal address which
can be returned for DMA allocations. If the mask is smaller than that,
we are unable to guarantee that the driver can reliably obtain suitable
memory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Separate the RiscPC specific (IOMD and floppy FIQ) data out of the core
DMA structure by making the IOMD and floppy DMA supersets.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having the central DMA multiplexer call the architecture
specific DMA initialization function, have each architecture DMA
initialization function use core_initcall(), and register each DMA
channel separately with the multiplexer.
This removes the array of dma structures in the central multiplexer,
replacing it with an array of pointers instead; this is more flexible
since it allows the drivers to wrap the DMA structure (eventually
allowing us to transition non-ISA DMA drivers away.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 8ec53663d2 ("[ARM] Improve
non-executable support") added support for detecting non-executable
stack binaries. One of the things it does is to make READ_IMPLIES_EXEC
be set in ->personality if we are running on a CPU that doesn't support
the XN ("Execute Never") page table bit or if we are running a binary
that needs an executable stack.
This exposed a latent bug in ARM's asm/processor.h due to which we'll
end up placing the stack at a very low address, where it will bump into
the heap on any application that uses significant amount of stack or
heap or both, causing many interesting crashes.
Fix this by testing the ADDR_LIMIT_32BIT bit in ->personality instead
of testing for equality against PER_LINUX_32BIT.
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 0c65f459ce intended to fix truncation issues with fls() on
ARMv5+ by renaming it to __fls() and wrapping it into a C function.
However that didn't take into account the fact that __fls() already
already had different semantics in the kernel.
Let's move the __fls() code into fls() function directly, and redefine
__fls() with the appropriate semantics. While at it, bring a generic
__fls() definition for pre ARMv5 too.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All the cases where the local timer for a CPU is accessed happen on the
corresponding current CPU, hence no need to access the per-CPU local
timer mappings.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RiscPC is the only platform using the default setting for NR_IRQS,
so the default NR_IRQS doesn't really make sense; remove it and
make RiscPC provide such a definition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definition of MAX_DMA_ADDRESS from mach/dma.h to mach/memory.h,
thereby placing it along side its relative, ISA_DMA_THRESHOLD.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no machine class overriding this. If non linear translations
are implemented again for some machines then this could be restored at
that time.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently there are two instances of struct meminfo: one in
kernel/setup.c marked __initdata, and another in mm/init.c with
permanent storage. Let's keep only the later to directly populate
the permanent version from arm_add_memory().
Also move common validation tests between the MMU and non-MMU cases
into arm_add_memory() to remove some duplication. Protection against
overflowing the membank array is also moved in there in order to cover
the kernel cmdline parsing path as well.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For similar reasons as copy_user_page(), we want to avoid the
additional kmap_atomic if it's unnecessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We used to override the copy_user_page() function. However, this
is not only inefficient, it also causes additional complexity for
highmem support, since we convert from a struct page to a kernel
direct mapped address and back to a struct page again.
Moreover, with highmem support, we end up pointlessly setting up
kmap entries for pages which we're going to remap. So, push the
kmapping down into the copypage implementation files where it's
required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CLPS7500 platform has not built since 2.6.22-git7 and there
seems to be no interest in fixing it. So, remove the platform
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton, remove memzero() - it's not supported
on other architectures so use of it is a potential build breaking bug.
Since the compiler optimizes memset(x,0,n) to __memzero() perfectly
well, we don't miss out on the underlying benefits of memzero().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mm/dma-mapping.c: In function `dma_sync_sg_for_cpu':
arch/arm/mm/dma-mapping.c:588: warning: statement with no effect
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Mikael Pettersson reported:
The 2.6.28-rc kernels fail to detect PCI device 0000:00:01.0
(the first ethernet port) on my Thecus n2100 XScale box.
There is however still a strange "ghost" device that gets partially
detected in 2.6.28-rc2 vanilla.
The IOP321 manual says:
The user designates the memory region containing the OCCDR as
non-cacheable and non-bufferable from the IntelR XScaleTM core.
This guarantees that all load/stores to the OCCDR are only of
DWORD quantities.
Ensure that the OCCDR is so mapped.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As a result of the ptebits changes, we ended up marking device mappings
as normal memory on ARMv7 CPUs, resulting in undesirable behaviour with
serial ports and the like. While reviewing the section mapping table
entries, other errors in the memory type settings for devices were
detected and confirmed to prevent Xscale3 platforms booting.
Tested on:
OMAP34xx (ARMv7),
OMAP24xx (ARMv6),
OMAP16xx (ARM926T, ARMv5),
PXA311 (Xscale3),
PXA272 (Xscale),
PXA255 (Xscale),
IXP42x (Xscale),
S3C2410 (ARM920T, ARMv4T),
ARM720T (ARMv4T)
StrongARM-110 (ARMv4)
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Ben Dooks <ben-linux@fluff.org>
Tested-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of 73bdf0a60e, the kernel needs
to know where modules are located in the virtual address space.
On ARM, we located this region between MODULE_START and MODULE_END.
Unfortunately, everyone else calls it MODULES_VADDR and MODULES_END.
Update ARM to use the same naming, so is_vmalloc_or_module_addr()
can work properly. Also update the comment on mm/vmalloc.c to
reflect that ARM also places modules in a separate region from the
vmalloc space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In case of non-aliasing VIPT caches, there is no need to flush the whole
cache when new mapping is created. The patch introduces this condition
check. In the non-aliasing VIPT case flush_cache_vmap() needs a DSB
since the set_pte_at() function called from vmap_pte_range() does not
have such barrier (done usually via TLB flushing functions).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Those inline assembly segments using the umlal instruction must have
the & modifier so to be sure that a purely input register won't alias
one of the registers used as input+output. In most cases, the inputs
are still used after the outputs are touched, and most binutil versions
insist on "rdhi, rdlo and rm must all be different" even for ARMv6+.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to confusion between the ftrace infrastructure and the gcc profiling
tracer "ftrace", this patch renames the config options from FTRACE to
FUNCTION_TRACER. The other two names that are offspring from FTRACE
DYNAMIC_FTRACE and FTRACE_MCOUNT_RECORD will stay the same.
This patch was generated mostly by script, and partially by hand.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The SET_PERSONALITY macro is always called with a second argument of 0.
Remove the ibcs argument and the various tests to set the PER_SVR4
personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
Most ARM machines don't need a special "DMA" memory zone, and
when configured out, the kernel becomes a bit smaller:
| text data bss dec hex filename
|3826182 102384 111700 4040266 3da64a vmlinux
|3823593 101616 111700 4036909 3d992d vmlinux.nodmazone
This is because the system now has only one zone total which effect is
to optimize away many conditionals in page allocation paths.
So let's configure this zone only on machines that need split zones.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide helpers for getting physical addresses or pfns from the
meminfo array, and use them. Move for_each_nodebank() to
asm/setup.h alongside the meminfo structure definition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for detecting non-executable stack binaries, and adjust
permissions to prevent execution from data and stack areas. Also,
ensure that READ_IMPLIES_EXEC is enabled for older CPUs where that
is true, and for any executable-stack binary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of the previous commit, MT_DEVICE_IXP2000 encodes to the same
PTE bit encoding as MT_DEVICE, so it's now redundant. Convert
MT_DEVICE_IXP2000 to use MT_DEVICE instead, and remove its aliases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide L_PTE_MT_xxx definitions to describe the memory types that we
use in Linux/ARM. These definitions are carefully picked such that:
1. their LSBs match what is required for pre-ARMv6 CPUs.
2. they all have a unique encoding, including after modification
by build_mem_type_table() (the result being that some have more
than one combination.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point scattering this around the tree, the parsing
of the parameter might as well live beside the code which uses
it. That also means we can make vmalloc_reserve a static
variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per the dma_unmap_* calls, we don't touch the cache when a DMA
buffer transitions from device to CPU ownership. Presently, no
problems have been identified with speculative cache prefetching
which in itself is a new feature in later architectures. We may
have to revisit the DMA API later for these architectures anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Validate the direction argument like x86 does. In addition,
validate the dma_unmap_* parameters against those passed to
dma_map_* when using the DMA bounce code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dmabounce dma_sync_xxx() implementation have been broken for
quite some time; they all copy data between the DMA buffer and
the CPU visible buffer no irrespective of the change of ownership.
(IOW, a DMA_FROM_DEVICE mapping copies data from the DMA buffer
to the CPU buffer during a call to dma_sync_single_for_device().)
Fix it by getting rid of sync_single(), moving the contents into
the recently created dmabounce_sync_for_xxx() functions and adjusting
appropriately.
This also makes it possible to properly support the DMA range sync
functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Delete ARM's own cnt32_to_63.h as the copy in include/linux/ should now be
used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can translate a struct page directly to a DMA address using
page_to_dma(). No need to use page_address() followed by
virt_to_dma().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than trying to (inaccurately) decode the cache type from the
registers each time we need to decide what type of cache we have,
use a bitmask initialized early during boot.
Since the setup is a one-off initialization, we can be a little more
clever and take account of the CPU architecture as well.
Note that we continue to achieve the compactness on optimised kernels
by forcing tests to always-false or always-true as appropriate, thereby
allowing the compiler to do build-time code elimination.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PCI_DMA_BUS_IS_PHYS was defined to be zero, which meant we ignored
the DMA mask for IDE and SCSI transfers. This is wrong - we have
no DMA translation hardware. We want to obey DMA masks so that the
block layer performs bouncing itself.
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch provides an ARM implementation of ioremap_wc().
We use different page table attributes depending on which CPU we
are running on:
- Non-XScale ARMv5 and earlier systems: The ARMv5 ARM documents four
possible mapping types (CB=00/01/10/11). We can't use any of the
cached memory types (CB=10/11), since that breaks coherency with
peripheral devices. Both CB=00 and CB=01 are suitable for _wc, and
CB=01 (Uncached/Buffered) allows the hardware more freedom than
CB=00, so we'll use that.
(The ARMv5 ARM seems to suggest that CB=01 is allowed to delay stores
but isn't allowed to merge them, but there is no other mapping type
we can use that allows the hardware to delay and merge stores, so
we'll go with CB=01.)
- XScale v1/v2 (ARMv5): same as the ARMv5 case above, with the slight
difference that on these platforms, CB=01 actually _does_ allow
merging stores. (If you want noncoalescing bufferable behavior
on Xscale v1/v2, you need to use XCB=101.)
- Xscale v3 (ARMv5) and ARMv6+: on these systems, we use TEXCB=00100
mappings (Inner/Outer Uncacheable in xsc3 parlance, Uncached Normal
in ARMv6 parlance).
The ARMv6 ARM explicitly says that any accesses to Normal memory can
be merged, which makes Normal memory more suitable for _wc mappings
than Device or Strongly Ordered memory, as the latter two mapping
types are guaranteed to maintain transaction number, size and order.
We use the Uncached variety of Normal mappings for the same reason
that we can't use C=1 mappings on ARMv5.
The xsc3 Architecture Specification documents TEXCB=00100 as being
Uncacheable and allowing coalescing of writes, which is also just
what we need.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pc_pointer() was a function to mask the PC for 26-bit ARMs, which
we no longer support. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit ae82cbfc8b. It
needs the new byteorder headers to be exported to userspace, and
they aren't yet -- and probably shouldn't be, at this point in the
2.6.27 release cycle (or ever, for that matter).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
The post-index immediate value is optional if it is 0 and this patch
removes it. The reason is to allow such instructions to compile to
Thumb-2 where only pre-indexed LDRT/STRT instructions are allowed.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a config option (CONFIG_VMSPLIT_*) to allow choosing
between 3:1, 2:2 and 1:3 user:kernel memory splits.
Tested-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_DEBUG_BUGVERBOSE is not set, we get warnings such as:
arch/arm/mm/ioremap.c: In function ‘remap_area_pte’:
arch/arm/mm/ioremap.c:67: warning: control reaches end of non-void function
mm/bootmem.c: In function ‘mark_bootmem’:
mm/bootmem.c:321: warning: control reaches end of non-void function
fs/dcache.c: In function ‘d_materialise_unique’:
fs/dcache.c:1875: warning: control reaches end of non-void function
fs/nfs/client.c: In function ‘nfs_sockaddr_match_ipaddr’:
fs/nfs/client.c:251: warning: control reaches end of non-void function
block/cfq-iosched.c: In function ‘cfq_async_queue_prio’:
block/cfq-iosched.c:1501: warning: control reaches end of non-void function
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux/ARM currently doesn't support robust or PI futexes.
The problem is that the kernel wants to perform certain ops
(cmpxchg, set, add, or, andn, xor) atomically on user-space
addresses, and ARM's futex.h doesn't support that.
This patch adds that support, but only for uniprocessor machines.
For UP it's enough to disable preemption to ensure mutual exclusion
with other software agents (futexes don't need to care about other
hardware agents, fortunately).
This patch is based on one posted by Khem Raj on 2007-08-01
<http://marc.info/?l=linux-arm-kernel&m=118599407413016&w=2>.
(That patch is included in the -RT kernel patches.)
My changes since that version include:
* corrected implementation of FUTEX_OP_ANDN (must complement oparg)
* added missing memory clobber to futex_atomic_cmpxchg_inatomic()
* removed spinlock because it's unnecessary for UP and insufficient
for SMP, instead the code is restricted to UP and relies on the
fact that pagefault_disable() also disables preemption
* coding style cleanups
Tested on ARMv5 XScales with the glibc-2.6 nptl test suite.
Tested-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As mentioned in commit 796969104c,
and because of commit b03a5b7559,
the direct calling of kprobe_trap_handler() can be removed.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than pollute asm/cacheflush.h with the cache type definitions,
move them to asm/cachetype.h, and include this new header where
necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add asm/cputype.h, moving functions and definitions from asm/system.h
there. Convert all users of 'processor_id' to the more efficient
read_cpuid_id() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
This patch removes CVS keywords that weren't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With gcc 4.3 and later, a pointer that has already been dereferenced is
assumed not to be null since it should have caused a segmentation fault
otherwise, hence any subsequent test against NULL is optimized away.
Current inline asm constraint used in the implementation of prefetch()
makes gcc believe that the pointer is dereferenced even though the PLD
instruction does not load any data and does not cause a segmentation
fault on null pointers, which causes all sorts of interesting results
when reaching the end of a linked lists for example.
Let's use a better constraint to properly represent the actual usage of
the pointer value.
Problem reported by Chris Steel.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename KEXEC_CONTROL_CODE_SIZE to KEXEC_CONTROL_PAGE_SIZE, because control
page is used for not only code on some platform. For example in kexec
jump, it is used for data and stack too.
[akpm@linux-foundation.org: unbreak powerpc and arm, finish conversion]
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2ccdd1e77d doesn't add
v7wbi_possible_flags and v7wbi_always_flags to possible_tlb_flags and
always_tlb_flags. This causes the L2 cache flush in clean_pmd_entry()
(intended for Feroceon only) to execute on ARMv7, and the CPU hangs.
This patch is required for OMAP3 boards to boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Setup some missing syscall pointed out by the checksyscalls.sh script. Fix two
small whitespace issues while being there.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the existing dma_sync_single_for_* APIs to the new range based
APIs, and make the dma_sync_single_for_* API a superset of it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP at least gets the return type(s) for the DMA translation functions
wrong, which can lead to subtle errors. Avoid this by moving the DMA
translation functions to asm/dma-mapping.h, and converting them to
inline functions.
Fix the OMAP DMA translation macros to use the correct argument and
result types.
Also, remove the unnecessary casts in dmabounce.c.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch will truncate and/or ignore memory banks if their kernel
direct mappings would (partially) overlap with the vmalloc area or
the mappings between the vmalloc area and the address space top, to
prevent crashing during early boot if there happens to be more RAM
installed than we are expecting.
Since the start of the vmalloc area is not at a fixed address (but
the vmalloc end address is, via the per-platform VMALLOC_END define),
a default area of 128M is reserved for vmalloc mappings, which can
be shrunk or enlarged by passing an appropriate vmalloc= command line
option as it is done on x86.
On a board with a 3:1 user:kernel split, VMALLOC_END at 0xfe000000,
two 512M RAM banks and vmalloc=128M (the default), this patch gives:
Truncating RAM at 20000000-3fffffff to -35ffffff (vmalloc region overlap).
Memory: 512MB 352MB = 864MB total
On a board with a 3:1 user:kernel split, VMALLOC_END at 0xfe800000,
two 256M RAM banks and vmalloc=768M, this patch gives:
Truncating RAM at 00000000-0fffffff to -0e7fffff (vmalloc region overlap).
Ignoring RAM at 10000000-1fffffff (vmalloc region overlap).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Riku Voipio <riku.voipio@iki.fi>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform independent header files to arch/arm/include/asm, leaving
those in asm/arch* and asm/plat* alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Gortmaker