The function ixgbe_init_mbx_params_pf isn't used unless CONFIG_PCI_IOV
is defined. This is causing namespace warnings. So I wrapped its
definition in CONFIG_PCI_IOV too.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We had a support function that just walked a few pointers to get
from the ixgbe_hw struct to the netdev pointer. This was causing
a namespace warning so I removed it and just reference the pointers
directly.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We didn't need the prototype and it was causing namespace complaints so
I made it static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This consolidates hardware specifics to ixgbe_dcb.c this simplifies
code that was previously branching based on hardware type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes the RESET bit previously used to force a device
reset when DCB bandwidth configurations were changed. This can
now be done dynamically without a reset so the bit is no longer
needed. The only remaining operations that force a device reset
are DCB enable/disable and FCoE application priority changes.
DCB enable/disable is a hardware requirement.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82599 and 82598 devices do not require hardware resets to
configure CEE pg settings. This patch changes DCB configuration
to set the CEE pg values directly from the dcbnl ops routine.
This reduces the number of resets seen on the wire and allows
LLDP to reach a steady state faster.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implements 802.1Qaz support for ixgbe driver. Additionally,
this adds IEEE_8021QAZ_TSA_{} defines to dcbnl.h this is to
avoid having to use cryptic numeric codes for the TSA type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the routines that configure the HW for DCB require a
ixgbe_dcb_config structure. This structure was designed to support
the CEE standard and does not match the IEEE standard well.
This patch changes the HW routines in ixgbe_dcb_8259x.{ch} to use
raw pfc and bandwidth values. This requires some parsing of the DCB
configuration but makes the HW routines independent of the data
structure that contains the DCB configuration.
The primary advantage to doing this is we can do HW setup directly
from the 802.1Qaz ops without having to arbitrarily encapsulate this
data into the CEE structure.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove round robin configuration code for 82598 parts it
is not settable and is always false.
If we need/want this in the future we can add it back properly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the FCoE priority is not changing do not set the RESET and
APP_UPCHG bits. This causes unneeded HW resets and which can
cause unneeded LLDP frames and negotiations.
The current check is not sufficient because the FCoE priority
can change twice during a negotiation which results in the
bits being set. This occurs when the switch changes the
priority or when the link is reset with switches that do not
include the APP priority until after PFC has been negotiated.
This results in set_app being called with the local APP
priority. Then the negotiation completes and set_app
is called again with the peer APP priority. The check
fails so the device is reset and the above occurs again
resulting in an endless loop of resets.
By only resetting the device if the APP priority has really
changed we short circuit the loop.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This will synchronize the version string with that of the latest source
forge driver which shares its functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_fcoe_ddp_get function wasn't initializing one of its variables
and this was producing compiler warnings. This patch cleans that up.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes VM pool allocation issues based on MAC address filtering,
as well as limits the scope of VF access to promiscuous mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have found a hardware erratum on 82599 hardware that can lead to
unpredictable behavior when Header Splitting mode is enabled. So
we are no longer enabling this feature on affected hardware.
Please see the 82599 Specification Update for more information.
CC: stable@kernel.org
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Caught with gcc 4.6 -Wunused-but-set-variable
Remove unused napi_vectors variable.
Fix the use of reset_bit in ixgbe_reset_hw_X540()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
After recent changes, (percpu stats on vlan/tunnels...), we dont need
anymore per struct netdev_queue tx_bytes/tx_packets/tx_dropped counters.
Only remaining users are ixgbe, sch_teql, gianfar & macvlan :
1) ixgbe can be converted to use existing tx_ring counters.
2) macvlan incremented txq->tx_dropped, it can use the
dev->stats.tx_dropped counter.
3) sch_teql : almost revert ab35cd4b8f (Use net_device internal stats)
Now we have ndo_get_stats64(), use it, even for "unsigned long"
fields (No need to bring back a struct net_device_stats)
4) gianfar adds a stats structure per tx queue to hold
tx_bytes/tx_packets
This removes a lockdep warning (and possible lockup) in rndis gadget,
calling dev_get_stats() from hard IRQ context.
Ref: http://www.spinics.net/lists/netdev/msg149202.html
Reported-by: Neil Jones <neiljay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes several issues found in ntuple filtering while I was
doing the ATR refactor.
Specifically I updated the masks to work correctly with the latest version
of ethtool, I cleaned up the exception handling and added detailed error
output when a filter is rejected, and corrected several bits that were set
incorrectly in ixgbe_type.h.
The previous version of this patch included a printk that was left over from
me fixing the filter setup. This patch does not include that printk.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a compressed input type for atr signature hash
computation. It also drops the use of the set functions when setting up
the ATR input since we can then directly setup the hash input as two dwords
that can be stored and passed as registers.
With these changes the cost of computing the has is low enough that we can
perform a hash computation on each TCP SYN flagged packet allowing us to
drop the number of flow director misses considerably in tests such as
netperf TCP_CRR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change cleans up the layout of the flow director data, and the
algorithm used to calculate the hash resulting in a 35x / 3500% performance
increase versus the old flow director hash computation. The overall effect
is only a 1% increase in transactions per second though due to the fact
that only 1 packet in 20 are actually hashed upon.
TCP_RR before:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23059.27
16384 87380
TCP_RR after:
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 60.00 23239.98
16384 87380
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disable the Rx logic globally, we would also want to disable the per Rx
queue receive logic by per queue Rx control register RXDCTL so no more DMA is
happening from the packet buffer to the receive buffer associated with the Rx
ring, before we start unmapping Rx ring receive buffer. The hardware may take
max of 100us before the corresponding Rx queue is really disabled. Added
ixgbe_disable_rx_queue() for this purpose.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the anti-spoofing feature in the HW. Packets from
VF devices with spoofed MAC addresses or VLAN tags will be blocked
and a counter incremented. During the watchdog timer the spoofed
packet dropped counter is read and if it is non-zero then a warning
message is displayed on the host VMM's console.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add X540 specific feature support to X540
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print warnings to the system log when the VF attempts to override
MAC/VLAN settings that were configured by the VMM Host administrator
using the ip link set commands.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
All three drivers use flush_scheduled_work() similarly during driver
detach. Replace it with explicit cancels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Some minor cleanup to use string calls that use bound checks just to
be extra safe.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit f62bbb5e62
ixgbe: Update ixgbe to use new vlan accleration.
removed ETH_FLAG_NTUPLE from the supported flags.
This patch puts it back on to allow for setting ntuple via ethtool.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables X540 hardware to use it's own set of support
functions. This is useful as it has no need of SFP+ support. A
couple minor bugs with the eeprom semaphore were also cleaned up.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing PHY ID for X540 was from early production hardware and
is no longer correct. This patch corrects that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on work by Joe Perches <joe@perches.com>
Using static const to decrease data and overall object size.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Fixes a recent bug on the patch (c6ecf39a10)
that disabled the laser on ifconfig down. Compilers were seeing a enum
mismatch.
Signed-off-by Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch helps prevent FW/SW semaphore collision from leading
to link establishment failure. The collision might mess up the
PHY registers so we reset the PHY. However there are SFI/KR areas
in the PHY that are not reset with a Reset_AN so we need to change
LMS to reset it. Also wait until AN state machine is AN_GOOD
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After freeing the rings we were not zeroing out the ring count values.
This patch now clears these counts correctly.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new PBA format is stored as a string. This patch allows the
driver to support both the old and new format.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add both NIC and backplane support for FCoE enabled devices IDs.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add wake on LAN support to the dev/sub_dev 10FB 11A9. This
will also include ixgbe ethtool support for this device.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have had several requests to have ifconfig down command disable
the SFP+ laser and thus make link go down. Likewise on ifconfig up
the laser would be enabled and link would come up. This patch enables
that behavior.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vzalloc() and vzalloc_node() in net drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will reflect addition of new X540 hardware
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed ring variable was initialized before allocations, and that
memory node management was a bit ugly. We also leak memory in case of
ring allocations error.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the x540 MAC which is the next MAC in the
82598/82599 line.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds the new x540.c file and Aquantia 1202 PHY for X540 support.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new MAC type X540 shares much of the same functionality of
some silicon specific functions. To reduce duplicate code,
made these functions generic.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When invalidating the DDP context is invalidated, the HW may not be done
with the user buffer right away. In which case, we poll the FCBUFF register
to check if the buffer valid bit is cleared or not, if not, we wait for max
100us that is guaranteed by the HW.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hw automatically invalidates the context if DDP is successful or there is
error detected. In case there is no error status available from the hw,
initializing the per context error status to be 1 allows the DDP context to be
still invalidated via the upper layer call to ddp_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no point to allow incoming DDP requests from the upper layer stack if
the adapter is going down or being reset.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx hang logic has been known to detect false hangs when
the device is receiving pause frames or has delayed processing
for some other reason.
This patch makes the logic more robust and resolves these
known issues. The old logic checked to see if the device
was paused by querying the HW then the hang logic was
aborted if the device was currently paused. This check was
racy because the device could have been in the pause state
any time up to this check. The other operation of the
hang logic is to verify the Tx ring is still advancing
the old logic checked the EOP timestamp. This is not
sufficient to determine the ring is not advancing but
only infers that it may be moving slowly.
Here we add logic to track the number of completed Tx
descriptors and use the adapter stats to check if any
pause frames have been received since the previous Tx
hang check. This way we avoid racing with the HW
register and do not detect false hangs if the ring is
advancing slowly.
This patch is primarily the work of Jesse Brandeburg. I
clean it up some and fixed the PFC checking.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change resolves some null function pointer accesses on 82598 when a
multi-speed fiber module is inserted into the adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The q_vector back pointer was not being set in the rings so it would not
have been possible to determine the parent q_vector of the ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up some of the items in ixgbe_map_rings_to_vectors.
Specifically it merges the two for loops and drops the unnecessary vectors
parameter.
It also moves the vector names into the q_vectors themselves.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve the stack utilization and simplify the math
used in ixgbe_set_itr_msix.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a number of places where we use the variable j to contain the
register index of the ring. Instead of using such a non-descriptive
variable name it is better that we name it reg_idx so that it is clear what
the variable contains.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is just to cleanup some confusing logic in ixgbe_cache_ring_rss
which can be simplified by adding a conditional with return to the start of
the call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change address a few whitespace issues in DCB #ifdefs, adds a comment
calling out the DCB specific registers, and nests an if statement inline
with a number of if statements related to flow control.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for certain 82599 based Mezzanine adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we always disable SCTP regardless of mac type
since we shouldn't need to check mac type before disabling a feature that
isn't supported on a given piece of hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces a number of if/elseif/else statements with switch
statements to support the addition of future devices to the ixgbe driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the use of rsc_count and changes it to a boolean since
the actual numerical value is used nowhere in the Rx cleanup path. I am
also moving the skb count into the RSC_CB path since it is much easier to
track it there than when it is passed as a parameter to various function
calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the ixgbe_atr filter setup function so that it uses
fewer items from the stack. Since the code is only applicable to IPv4 w/
TCP it makes sense to just use the pointers based on the headers themselves
instead of copying them to temp variables and then writing those to the
filters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code for ixgbe_clean_rx_irq was much more tangled up than it needed to
be in terms of logic statements and unused variables. This change
untangles much of that and drops several unused variables such as cleaned
which was being returned but never checked.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This changes the numbering scheme slightly. Previously the ordering was
coming out like this:
Rx-2
Rx-1
Rx-0
TxRx-0
Which would drop two queues on CPU 0. This change makes it so that the
ordering is like this:
Rx-3
Rx-2
Rx-1
TxRx-0
This means that each CPU will have it's own Rx queue, and only CPU 0 will
have the Tx queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code as it existed could re-arm the queues when it was requesting a HW
reset due to a TX hang. Instead of doing that this change makes it so that
we will just exit if the hardware is believed to be hung.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSC will flush its descriptors every time the interrupt throttle timer
expires. In addition there are known issues with RSC when the rx-usecs
value is set too low. As such we are forced to clear the RSC_ENABLED bit
and reset the adapter when the rx-usecs value is set too low.
However we do not need to clear the NETIF_F_LRO flag because it is used to
indicate that the user wants to leave the LRO feature enabled, and in fact
with this change we will now re-enable RSC as soon as the rx-usecs value is
increased and the flag is still set.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we perform link setup with interrupts
disabled. If the SFP has not been detected previously we will schedule the
SFP detection task to run in order to detect link. By doing this we avoid
the possibility of interrupts firing in the middle of our link setup during
ixgbe_up_complete.
In addition this change makes it so that the multi-speed fiber setup and SFP
setup are not mutually exclusive. The addresses issues seen in which a
link would only come up at 1G on some multi-speed fiber modules.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds a set of state flags to the rings that allow them to
independently function allowing for features like RSC, packet split, and
TX hang detection to be done per ring instead of for the entire device.
This is accomplished by re-purposing the flow director reinit_state member
and making it a global state instead since a long for a single bit flag is
a bit wasteful.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the start of work to sort out what belongs in the rings and what
belongs in the q_vector. Items like the CPU variable for make much more
sense in the q_vector since the CPU is a per-interrupt thing rather than a
per ring thing.
I also added a back-pointer from the ring to the q_vector.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves an adapter pointer into the private portion of the
pci_dev instead of a pointer to the netdev. The reason for this change is
because in most cases we just want the adapter anyway. In addition as we
start moving toward multiple netdevs per port we may want to move the
adapter pointer out of the netdevs entirely.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Missed some code that was left floating around in the DCB configuration
for the TXDCTL register. As a result the register was being messed with in
two different spots when we only needed to do the change once.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The main reason for this change is to keep the suspend/resume logic matched
up. The clear_interrupt_scheme function will disable MSI-X which will
effect the PCIe configuration space. Therefore we will want to do it before
we save state to avoid having the interrupt state restored by
pci_restore_state, and then trying to re-enable MSI/MSI-X interrupts via
ixgbe_setup_interrupt_scheme.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change places a netdev pointer directly into the ring structure. This
way we can avoid having to determine which netdev we are supposed to be
using and can just access the one on the ring directly.
As a result of this change further collapse of the code is possible by
dropping the adapter from ixgbe_alloc_rx_buffers, and the netdev pointer
from ixgbe_xmit_frame_ring_adv and ixgbe_maybe_stop_tx.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moved some of the RX and TX stats into separate structures and
them placed those structures in a union in order to help reduce the size of
the ring structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to simplify DMA map/unmap by providing a device
pointer. As a result the adapter pointer can be dropped from many of
the calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change drops ring->head since it is not used in any hot-path and can
easily be determined using IXGBE_[RT]DH(ring->reg_idx).
It also changes ring->tail into a true pointer so we can avoid unnecessary
pointer math to find the location of the tail.
In addition I also dropped the setting of head and tail in
ixgbe_clean_[rx|tx]_ring. The only location that should be setting the head
and tail values is ixgbe_configure_[rx|tx]_ring and that is only while the
queue is disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change re-orders alloc_rx_buffers to make better use of the packet
split enabled flag. The new setup should require less branching in the
code since now we are down to fewer if statements since we either are
handling packet split or aren't.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change simplifies the work being done by the TX interrupt handler and
pushes it into the tx_map call. This allows for fewer cache misses since
the TX cleanup now accesses almost none of the skb members.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no need to reset the adapter when changing the Rx checksum
settings. Since the only change is a software flag we can disable it
without needing to reset the entire adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The maximum credits per traffic class only needs to be greater
then the TSO size for 82598 devices. The 82599 devices do not
have this requirement so only do this test for 82598 devices.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the high and low water marks for PFC are being set
conservatively for jumbo frames. This means the RX buffers
are being underutilized in the default 1500 MTU. This patch
fixes this so that the water marks are set as described in
the data sheet considering the MTU size.
The equation used is,
RTT * 1.44 + MTU * 1.44 + MTU
Where RTT is the round trip time and MTU is the max frame size
in KB. To avoid floating point arithmetic FC_HIGH_WATER is
defined
((((RTT + MTU) * 144) + 99) / 100) + MTU
This changes how the hardware field fc.low_water and
fc.high_water are used. With this change they are no longer
storing the actual low water and high water markers but are
storing the required head room in the buffer. This simplifies
the logic and we do not need to account for the size of the
buffer when setting the thresholds.
Testing with iperf and 16 threads showed a slight uptick in
throughput over a single traffic class .1-.2Gbps and a reduction
in pause frames. Without the patch a 30 second run would show
~10-15 pause frames being transmitted with the patch ~2-5 are
seen. Test were run back to back with 82599.
Note RXPBSIZE is in KB and low and high water marks fields are
also in KB. However the FCRT* registers are 32B granularity and
right shifted 5 into the register,
(((rx_pbsize - water_mark) * 1024) / 32) << 5
is the most explicit conversion here we simplify
(rx_pbsize - water_mark) * 32 << 5 = (rx_pbsize - water_mark) << 10
This patch updates the PFC thresholds and legacy FC thresholds.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"cat /proc/net/dev" uses RCU protection only.
Its quite possible we call a driver get_stats() method while device is
dismantling and freeing its data structures.
So get_stats() methods must be very careful not accessing driver private
data without appropriate locking.
In ixgbe case, we access rx_ring pointers. These pointers are freed in
ixgbe_clear_interrupt_scheme() and set to NULL, this can trigger NULL
dereference in ixgbe_get_stats64()
A possible fix is to use RCU locking in ixgbe_get_stats64() and defer
rx_ring freeing after a grace period in ixgbe_clear_interrupt_scheme()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Tantilov, Emil S <emil.s.tantilov@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the skb->protocol field is used to setup various
offloading parameters on transmit for the correct protocol.
However, if vlan offloading is disabled or otherwise not used,
the protocol field will be ETH_P_8021Q, not the actual protocol.
This will cause the offloading to be not performed correctly,
even though the hardware is capable of looking inside vlan tags.
Instead, look inside the header if necessary to determine the
correct protocol type.
To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DCB credits refill quantum _must_ be greater than half the max
packet size. This is needed to guarantee that TX DMA operations
are not attempted during a pause state. Additionally, the min IFG
must be set correctly for DCB mode. If a DMA operation is
requested unexpectedly during the pause state the HW data
store may be corrupted leading to a DMA hang. The DMA hang
requires a reset to correct. This fixes the HW configuration
to avoid this condition.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FCoE offload is enabled/disabled per adapter, but upper FCoE protocol
stack could have multiple FCoE instances created on the same physical network
interface, e.g., FCoE on multiple VLAN interfaces on the same physical
network interface. In this case we want to turn on FCoE offload at the first
request from ndo_fcoe_enable() but only turn off FCoE offload at the very last
call to ndo_fcoe_disable(). This is fixed by adding a refcnt in the per adapter
FCoE structure and tear down FCoE offload when refcnt decrements to zero.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ixgbe stats have following problems :
- Not 64 bit safe (on 32bit arches)
- Not safe in ixgbe_clean_rx_irq() :
All cpus dirty a common location (netdev->stats.rx_bytes &
netdev->stats.rx_packets) without proper synchronization.
This slow down a bit multiqueue operations, and possibly miss some
updates.
Fixes :
Implement ndo_get_stats64() method to provide accurate 64bit rx|tx
bytes/packets counters, using 64bit safe infrastructure.
ixgbe_get_ethtool_stats() also use this infrastructure to provide 64bit
safe counters.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update copyright notice
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the ixgbe driver use the new vlan accleration model.
Signed-off-by: Jesse Gross <jesse@nicira.com>
CC: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many (but not all) drivers check to see whether there is a vlan
group configured before using a tag stored in the skb. There's
not much point in this check since it just throws away data that
should only be present in the expected circumstances. However,
it will soon be legal and expected to get a vlan tag when no
vlan group is configured, so remove this check from all drivers
to avoid dropping the tags.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a DCB check config from DCB configuration we
continue to configure DCB even if it fails so don't
even bother to check. Plus user space (lldpad) checks
this before programming the hw anyways.
Worse case is we program some values into the hw that
don't make total sense resulting in incorrect bandwidth
allocation.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch fixes warnings reported by `make namespacecheck`
Reported by Stephen Hemminger
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove functions that are declared, but not used in the driver.
This patch fixes warnings reported by `make namespacecheck`
Reported by Stephen Hemminger
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new infrastructure to balance interrupts for flow
alignment when ATR or Flow Director are enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible panic/hang with shared Legacy interrupts by not enabling
interrupts when interface is down.
Also fixes an intermittent link by enabling LSC upon exit from ixgbe_intr()
This patch adds flags to ixgbe_irq_enable() to allow for some flexibility
when enabling interrupts.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the netdev->features is set with NETIF_F_HIGHDMA, we should set the
corresponding netdev->vlan_features as well to allow VLAN netdev created
on top of the real netdev to be able to also benefit from HIGHDMA on 32bit
system, reducing the performance hit that is caused by __skb_linearize(),
particularly for large send. This is fixed in this patch for all Intel e1000,
e1000e, igb, ixgbe, and ixgbe drivers since this should be beneficial
to all devices supported by these drivers.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool utility does not set masks for flow parameters that are
not specified, so if both value and mask are 0 then this must be
treated as equivalent to a mask with all bits set. Currently that is
done in the only driver that implements RX n-tuple filtering, ixgbe.
Move it to the ethtool core.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce indentation in a couple of places
Add static function ixgbe_psum
Add temporary for adapter->stats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Did not add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
because no printk in this module used message prefixing.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whitespace cleanups.
Move inline keyword after function type declarations.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ordering of operations was messed up in the init and as a result when
VMDQ was enabled we were trying to enable TX rings before setting the VFTE
bits. This resulted in a ring that appeared to fail to enable when in fact
it was blocked because the VFTE bits were cleared after the reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"foo = &function" is more commonly written "foo = function"
Done with coccinelle script:
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
drivers/net/tehuti.c used a function and struct with the
same name, the function was renamed.
Compile tested x86 only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the ethtool loopback test uses the standard
ring configuration and allocation functions. As a result the loopback test
will be much more effective at testing core driver functionality.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the DESC_ADV macros are currently needing the pointers to be
de-referenced before accessing the ring. Instead of having to add all of
the asterisks it is easier to just update the macro to expect a pointer to
the ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx init is currently split over ixgbe_configure, ixgbe_configure_rx,
and ixgbe_up_complete. Instead of leaving it split over 3 function it is
easier to consolidate them all into ixgbe_configure_rx.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx init was spread out over ixgbe_configure, ixgbe_configure_tx, and
ixgbe_up_complete. This change combines all of that into the
ixgbe_configure_tx function in order to simplify the Tx init path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves all GPIE register configuration into a single function.
The advantage of this is that we can avoid a number of unnecessary
read/modify/write cycles on the register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves the configuration that was done in configure_rx into a
separate virtualization configuration function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves all of the Rx DMA control register writes to one central
location. This should help to avoid accidentally overwriting existing
settings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change consolidates all of the Rx max frame size and Rx buffer length
configuration into a single function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vmolr is configured already in ixgbe_set_rx_mode for the PF so there is
no need to set it again in ixgbe_configure_rx.
Instead of using the variable name reg, it is easier to just rename it to
gcr_ext to reflect the register contents that the variable holds.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump the header size for packet split to 512 bytes since this makes the
best use of the 1k buffer that is allocated for any skb 512 bytes or
smaller.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are accessing the FCTRL register in multiple spots in the init path and
we can simplify things by combining the configuration all into
ixgbe_set_rx_mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configuration of PSRTYPE was being done conditionally on if packet
split is enabled or not. It can be configured always since it will not
have any effect when packet split is not enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These changes add ixgbe_configure_rx_ring which is used to setup the base
function pointers for the ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change simplifies the configuration of MRQC by consolidating the
setting of it into one function. As such the register is no longer set in
multiple places which should make any future changes easier to work with.
In addition we can combine RSS related register writes into the call since
enabling all of those bits without enabling RSS itself in MRQC should have
no effect.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the Tx ring configuration into a separate function. In
addition the function drops the setting of the head writeback RO bit since
head writeback is no longer used within ixgbe.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the configuration of the MTQC register into it's own
function call similar to ixgbe_setup_mrqc.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ixgbe_up_complete we were doing a read-modify-write of TXDCTL followed
by another one just a few lines further down. Instead of performing two
separate read-modify-writes it would make more sense to combine the two
into one.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are unnecessarily modifying the GSO size for all HW when we don't need
to. The code can be simplified by moving the check for DCB and the
adjustment of the GSO size for 82598 into ixgbe_configure_dcb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the redundant DMA alignment code from the Rx buffer
allocation path. This code is no longer necessary since all x86 buffers
are now DMA aligned due to recent changes to NET_IP_ALIGN and NET_SKB_PAD.
It also moves the setting of the Rx queue value into the allocation path
since it is more likely that the queue mapping will still be in the cache
at the time of allocation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code in ixgbe_get_drvinfo more protected against buffer overflow
boundaries by using snprintf and sizeof with snprintf.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patches from Sonny Rao and Milton Miller...
Combined the patches to fix up clean_tx_irq and clean_rx_irq.
The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.
This bug was found during stress testing and adding this barrier has
been shown to fix it. The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().
This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.
Previously Submitted to e1000-devel only for ixgbe
http://marc.info/?l=e1000-devel&m=126593062701537&w=3
We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.
CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause
a build error. This resolves the build error by wrapping
the fcoe.up in CONFIG_IXGBE_DCB ifdefs.
Also frames were being priority VLAN tagged even without DCB
enabled. This fixes this so that 8021Q priority tags are
only added with DCB actually enabled.
Reported-by: divya <dipraksh@linux.vnet.ibm.com>
Reported-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e_dev_err() macro dereferences "adapter" which is NULL here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DCB user priority for FCoE is available regardless of whether
FCoE offload is enabled (IXGBE_FLAG_FCOE_ENABLED bit is set).
This allows proper DCB user priority tagging for FCoE
traffic on both 82598 and 82599 devices.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In latest changes about 64bit stats on 32bit arches,
[commit 28172739f0 (net: fix 64 bit counters on 32 bit arches)],
I missed ixgbe uses a bit of magic in its ixgbe_gstrings_stats
definition.
IXGBE_NETDEV_STAT() must now assume offsets relative to
rtnl_link_stats64, not relative do dev->stats.
As a bonus, we also get 64bit stats on ethtool -S
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ixgbe cards put an invalid VF device ID in the PCIe SR-IOV
capability. The ixgbe driver is only valid for PFs or non SR-IOV
hardware. It seems that the same problem could occur on igb hardware as
well, so if we discover we are trying to initialize a VF in ixbge_probe
or igb_probe, print an error and exit.
Based on a patch for ixgbe from Chris Wright <chrisw@sous-sol.org>.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: Chris Wright <chrisw@sous-sol.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump the version string to better reflect what is in the driver.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FCoE protocol stack may hold a lock when this gets called.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When FCoE is disabled, there is a race condition that FCoE offload is
turned off but the FCoE protocol driver is still queuing I/O thinking
offload support still exists. This patch toggles off corresponding FCoE
netdev feature flags and notify the FCoE stack first, allowing FCoE
protocol stack driver to update its flags upon NETDEV_FEAT_CHANGE so no
I/O will be using offload.
Also, indicate FCoE offload flags in vlan_features in ixgbe_probe once
and do not toggle them in ixgbe_fcoe_enable/disable so when FCoE is
created on the VLAN interface, vlan_transfer_features() would properly
update the VLAN netdev features flag and notify the FCoE protocol driver
for NETDEV_FEAT_CHANGE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change removes UDP from the supported protocols for RSS hashing. The
reason for removing this protocol is because IP fragmentation was causing a
network flow to be broken into two streams, one for fragmented, and one for
non-fragmented and this in turn was causing out-of-order issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the DPF bit when PFC is enabled. This will discard
PFC frames so they do not get passed up the stack.
The DPF bit is set for flow control, but not priority
flow control this brings pfc inline with fc.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.
One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().
Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)
Old drivers (only providing get_stats() method) need no changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restores the ability to set msglvl through ethtool.
The issue was introduced by:
commit 849c45423c
CC: Joe Perches <joe@perches.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reducing real_num_queues needs to flush the qdisc otherwise
skbs with queue_mappings greater then real_num_tx_queues can
be sent to the underlying driver.
The flow for this is,
dev_queue_xmit()
dev_pick_tx()
skb_tx_hash() => hash using real_num_tx_queues
skb_set_queue_mapping()
...
qdisc_enqueue_root() => enqueue skb on txq from hash
...
dev->real_num_tx_queues -= n
...
sch_direct_xmit()
dev_hard_start_xmit()
ndo_start_xmit(skb,dev) => skb queue set with old hash
skbs are enqueued on the qdisc with skb->queue_mapping set
0 < queue_mappings < real_num_tx_queues. When the driver
decreases real_num_tx_queues skb's may be dequeued from the
qdisc with a queue_mapping greater then real_num_tx_queues.
This fixes a case in ixgbe where this was occurring with DCB
and FCoE. Because the driver is using queue_mapping to map
skbs to tx descriptor rings we can potentially map skbs to
rings that no longer exist.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ETH_FLAG_LRO and NETIF_F_LRO have the same value, but NETIF_F_LRO
is intended to use with netdev->features.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 1G SFP+ PHY's to 82599.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool_op_set_flags() does not check for unsupported flags, and has
no way of doing so. This means it is not suitable for use as a
default implementation of ethtool_ops::set_flags.
Add a 'supported' parameter specifying the flags that the driver and
hardware support, validate the requested flags against this, and
change all current callers to pass this parameter.
Change some other trivial implementations of ethtool_ops::set_flags to
call ethtool_op_set_flags().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In driver ixgbe, ixgbe_atr may cause crashes for non-ipv4 packets. Just
add a test to check skb->protocol. It may crash on short packets due
to ip_hdr() access.
Signed-off-by: Guillaume Gaudonville <guillaume.gaudonville@6wind.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling the tx laser while receiving DMA requests
can hang the device. After this occurs the device
is in a bad state. The GPIO bit never clears when
PCI master access is disabled and a reboot is required
to get the device in a good state again.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added to 2.6.34:
commit 5f6c018199
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
Date: Wed Apr 14 16:04:23 2010 -0700
ixgbe: fix bug with vlan strip in promsic mode
among other things added a function called ixgbe_vlan_filter_enable.
This new function wants to access and set some rx_ring parameters, but
adapter->rx_ring has already been freed. This simply moves the free
until after the access and makes __ixgbe_shutdown look more like
ixgbe_remove.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
