The omap1_defconfig this should be eventually usable for booting
all omap1 machines. Generated based on:
$ grep ARCH_OMAP1=y arch/arm/configs/* | cut -d: -f1 | xargs cat | \
sort | uniq >> arch/arm/configs/omap1_defconfig
Then change few things manually, like use Nokia 770 CONFIG_CMDLINE
as it does not allow setting it in the bootloader.
Finally ran make savedefconfig on it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise multi-omap1 support for omap1 won't work as the cpu_class_is_omap1()
won't work until the SoC is detected.
Note that eventually these will go away, please use ioremap + read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize asm_irq_flags in omap_init_irq and use it in
get_irqnr_and_base to detect between omap7xx and omap15xx/16xx.
Note that both INT_1510_IH2_IRQ and INT_1510_IH2_IRQ are defined
as 0, so use INT_1510_IH2_IRQ for both of them.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using true/false instead of 1/0 to update the free variable.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Function omap_mcbsp_probe allocates struct omap_mcbsp *mcbsp but it is not
freed in omap_mcbsp_remove. Fix this, remove unneeded structure cleanups
and clk_disable calls since they are not needed here.
This is not problem currently but becomes if the mcbsp driver is ever
modularized.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Value of "isr_reg" pointer is depend on configuration and GPIO method.
Potentially it may have NULL value and it is dereferenced later
in code. Warning and exit from function are added in this case.
Signed-off-by: Evgeny Kuznetsov <EXT-Eugeny.Kuznetsov@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some cases we can get error function `omap2_i2c_add_bus':
arch/arm/plat-omap/i2c.c:136: undefined reference to `omap2_i2c_mux_pins'
arch/arm/plat-omap/i2c.c:141: undefined reference to `omap_hwmod_lookup'
arch/arm/plat-omap/i2c.c:157: undefined reference to `omap_device_build'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 4d17aeb1c5 ("OMAP: I2C: split
device registration and convert OMAP2+ to omap_device") broke I2C on
OMAP1. The following messages appear at boot:
i2c_omap i2c_omap.1: failure requesting irq 0
i2c_omap: probe of i2c_omap.1 failed with error -22
Investigation revealed that a chunk of code is missing from the
original plat-omap/i2c.c file which configured the IRQ and base address
for the I2C block on OMAP1. Upon adding this back, the OMAP1 I2C block
seems to initialize correctly.
Thanks to Cory Maccarrone <darkstar6262@gmail.com> for reporting the bug,
and apologies for the breakage.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 0ea1293009 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.
Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6524/1: GIC irq desciptor bug fix
ARM: 6523/1: iop: ensure sched_clock() is notrace
ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
ARM: cns3xxx: Fix build with CONFIG_PCI=y
gic_set_cpu will directly use irq_desc[]. If CONFIG_SPARSE_IRQ is
enabled, there is no irq_desc[]. So we need use irq_to_desc(irq) to
get the descriptor for irq.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The existing code invokes the syscall with rubbish in r7,
due to what looks like an incorrect literal load idiom.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_OMAP_MUX is not enabled, we can define board_mux in the header
file instead of forcing every single board to define it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated for combined board-zoom files]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Access to some registers depends on register access mode
Three different modes are available for OMAP (at least)
• Operational mode LCR_REG[7] = 0x0
• Configuration mode A LCR_REG[7] = 0x1 and LCR_REG[7:0]! = 0xBF
• Configuration mode B LCR_REG[7] = 0x1 and LCR_REG[7:0] = 0xBF
Define access modes and remove redefinitions and magic numbers
in serial drivers (and later in bluetooth driver).
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define MDR1 register serial definitions used in serial and
bluetooth drivers.
Change magic number to ones defined in serial_reg for omap1/2
serial driver.
Remove redefined MDR1 register definitions in omap-serial driver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Craneboard is a hardware development platform based on the
Sitara AM3517 ARM Cortex - A8 microprocessor device. This is a
low cost reference design.
This patch adds basic board file. Detailed support will follow in
subsequent patches.
[1] http://www.ti.com/arm
[2] http://www.mistralsolutions.com/products/craneboard.php
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patches removes a config option that was used to select a FIQ
handler to be build for Amstrad Delta, as required by the on-board serio
interface driver. Not having any problem reports received since it was
introduced in 2.6.35, the FIQ handler can now be built and initialized by
default, thus reqiring no extra config option.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It's easier to understand what that number means and
also avoids problems if we ever have to change it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
They are extremely similar anyway, let's get rid
of one file.
While at that, also remove the empty zoom_config
variable.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The changes are:
- Use 'for' loop instead 'while' loop.
- No need to initialize ret to 0, we're assigning it right after.
- No need to check for onenandcs < GPMC_CS_NUM here, it will always be true.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_board_config_size is implicitly initialized to 0 in
plat-omap/common.c, get_config() won't dereference omap_board_config,
so we can remove the empty igep2_config array.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
to be a few more concistant with the other boards
as ek is for evaluation kit and dk for development kit
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Ajeco 1ARM Single Board Computer
- Sperry-Sun KAFA board
- picotux 200
Remove the deprecated at91_init_serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Currently, the kprobes implementation for ARM only supports the ARM
instruction set, so it only works if CONFIG_THUMB2_KERNEL is not
enabled.
Until kprobes is updated to work with Thumb-2, turning it on will
cause horrible things to happen, so this patch disables it for now.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C. If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.
In general, the following rules should be applied when using
data word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned data
words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume that
fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned, this
can cause impaired performance and stray alignment faults in some
circumstances.
In general, the following rules should be applied when using data word
declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 32-bit conditional branches in Thumb-2 have a shorter range
(+/-512K) than their ARM counterparts (+/-32MB). The linker does
not currently generate trampolines to extend the range of these
Thumb-2 conditional branches, resulting in link errors when vmlinux
is sufficiently large, e.g.:
head.o:(.text+0x464): relocation truncated to fit: R_ARM_THM_JUMP19
This patch forces the longer-range, unconditional branch encoding
by use of an explicit IT instruction. The resulting branches are
triggered on the same conditions as before.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code which makes up the zImage header intends to leave a
32-byte gap followed by a branch to the real entry point, a magic
number, and a word containing the absolute entry point address.
This gets messed up with with CONFIG_THUMB2_KERNEL, because the
size of the initial padding NOPs changes.
Instead, the header can be made fully compatible by restoring it to
ARM.
In the Thumb-2 case, we can replace the initial NOPs with a
sequence which switches to Thumb and jumps to the real entry point.
As a consequence, the zImage entry point is now always ARM, so no
special magic is needed any more for the uImage rules in the
Thumb-2 case.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some instruction operand combinations are used here which are nor
permitted in Thumb-2.
In particular, most uses of pc as an operand are disallowed in
Thumb-2, and deprecated in ARM from ARMv7 onwards.
The modified code introduced by this patch should be compatible
with all architecture versions >= v3, with or without
CONFIG_THUMB2_KERNEL.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
In this specific case, we can achieve the desired alignment by
forcing a 32-bit branch instruction using the W() macro, since the
assembler location counter is already 32-bit aligned in this case.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C. If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.
In general, the following rules should be applied when using data
word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
