Commit graph

1950 commits

Author SHA1 Message Date
Daniel Kurtz
0da2e7768b i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
The datasheet says that the STOP sequence should be:
 1) I2CSTAT.5 = 0	- Clear BUSY (or 'generate STOP')
 2) I2CCON.4 = 0	- Clear IRQPEND
 3) Wait until the stop condition takes effect.
 4*) I2CSTAT.4 = 0 	- Clear TXRXEN

Where, step "4*" is only for buses with the "HDMIPHY" quirk.

However, after much experimentation, it appears that:
 a) normal buses automatically clear BUSY and transition from
    Master->Slave when they complete generating a STOP condition.
    Therefore, step (3) can be done in doxfer() by polling I2CCON.4
    after starting the STOP generation here.
 b) HDMIPHY bus does neither, so there is no way to do step 3.
    There is no indication when this bus has finished generating STOP.

In fact, we have found that as soon as the IRQPEND bit is cleared in
step 2, the HDMIPHY bus generates the STOP condition, and then immediately
starts transferring another data byte, even though the bus is supposedly
stopped.  This is presumably because the bus is still in "Master" mode,
and its BUSY bit is still set.

To avoid these extra post-STOP transactions on HDMI phy devices, we just
disable Serial Output on the bus (I2CSTAT.4 = 0) directly, instead of
first generating a proper STOP condition.  This should float SDA & SCK
terminating the transfer.  Subsequent transfers start with a proper START
condition, and proceed normally.

The HDMIPHY bus is an internal bus that always has exactly two devices,
the host as Master and the HDMIPHY device as the slave. Skipping the STOP
condition has been tested on this bus and works.

Also, since we disable the bus directly from the isr, we can skip the bus
idle polling loop at the end of doxfer().

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 13:08:55 +01:00
Daniel Kurtz
9bcd04bfbb i2c: s3c2410: grab adapter lock while changing i2c clock
We probably don't want to change I2C frequency while a transfer is in
progress.  The current implementation grabs a spinlock, but that only
protected the writes to IICCON when starting a message, it didn't protect
against clock changes in the middle of a transaction.

Note: The i2c-core already grabs the adapter lock before calling
s3c24xx_i2c_doxfer(), which ensures that only one caller is issuing a
xfer at a time. This means it is not necessary to disable interrupts
(spin_lock_irqsave) when changing frequencies, since there won't be
any i2c interrupts if there is no on-going xfer.

Lastly, i2c_lock_adapter() may cause the cpufreq_transition to sleep if
if a xfer is in progress, but this is ok since cpufreq notifiers are
called in a kernel thread, and there are already cases where it could
sleep, such as when using i2c to update the output of a voltage
regulator.

Note: the cpufreq part of this change has no functional affect on
	exynos, where the i2c clock is independent of the cpufreq.
	But, there is a slight perfomance boost since we no longer need to
	lock/unlock an additional spinlock.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 13:08:48 +01:00
Tomasz Figa
2693ac6988 i2c: s3c2410: Add support for pinctrl
This patch adds support for pin configuration using pinctrl subsystem
to the i2c-s3c2410 driver.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 12:53:25 +01:00
Mark Brown
a72ad456bb i2c: s3c2410: Convert to devm_request_and_ioremap()
A small code saving and less error handling to worry about.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 12:53:17 +01:00
Mark Brown
2935e0e05a i2c: s3c2410: Refactor ifdefs for PM_SLEEP
Use the PM_SLEEP ifdef for system suspend and resume. This is partly
in preparation for adding runtime operations and partly because a user
may in theory choose to enable runtime suspend but not system suspend.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 12:53:10 +01:00
Maxime Ripard
9b7a0c40de i2c: mux: Add dt support to i2c-mux-gpio driver
Allow the i2c-mux-gpio to be used by a device tree enabled device. The
bindings are inspired by the one found in the i2c-mux-pinctrl driver.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>

[wsa: fixed some whitespace]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 09:28:27 +01:00
Shinya Kuribayashi
29fb08c300 i2c: i2c-sh_mobile: fix spurious transfer request timed out
Ensure that any of preceding register write operations to the I2C
hardware block reached the module, and the write data is reflected
in the registers, before leaving the interrupt handler.

Otherwise, we'll suffer from spurious WAIT interrupts that lead to
'Transfer request timed out' message, and the transaction failed.

Reported-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 09:09:13 +01:00
Shinya Kuribayashi
ebd5ac165f i2c: i2c-sh_mobile: support I2C hardware block with a faster operating clock
On newer SH-/R-Mobile SoCs, a clock supply to the I2C hardware block,
which is used to generate the SCL clock output, is getting faster than
before, while on the other hand, the SCL clock control registers, ICCH
and ICCL, stay unchanged in 9-bit-wide (8+1).

On such silicons, the internal SCL clock counter gets incremented every
2 clocks of the operating clock.

This patch makes it configurable through platform data.

Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 09:09:12 +01:00
Shinya Kuribayashi
23a612916a i2c: i2c-sh_mobile: optimize ICCH/ICCL values according to I2C bus speed
ICCH/ICCL values is supposed to be calculated/optimized to strictly meet
the timing specs required by the I2C standard. The resulting I2C bus
speed does not matter at all, if it's less than 100 or 400 kHz.

With this change, sh_mobile_i2c_icch() is virtually identical to
sh_mobile_i2c_iccl(), but they're providing good descriptions of
SH-/R-Mobile I2C hardware spec, and I'd leave them as separated.

Also fix a typo in the comment, print icch/iccl values at probe, etc.

Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>

[wsa: squashed two patches for bisectability]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 09:07:43 +01:00
Shinya Kuribayashi
7b0e62920a i2c: i2c-sh_mobile: calculate clock parameters at driver probing time
Currently SCL clock parameters (ICCH/ICCL) are calculated in
activate_ch(), which gets called every time sh_mobile_i2c_xfer() is
processed, while each I2C bus speed is system-defined and in general
those parameters do not have to be updated over I2C transactions.

The only reason I could see having it transaction-time is to adjust
ICCH/ICCL values according to the operating frequency of the I2C
hardware block, in the face of DFS (Dynamic Frequency Scaling).

However, this won't be necessary.

The operating frequency of the I2C hardware block can change _even_
in the middle of I2C transactions.  There is no way to prevent it
from happening, and I2C hardware block can work with such dynamic
frequency change, of course.

Another is that ICCH/ICCL clock parameters optimized for the faster
operating frequency, can also be applied to the slower operating
frequency, as long as slave devices work.  However, the converse is
not true.  It would violate SCL timing specs of the I2C standard.

What we can do now is to calculate the ICCH/ICCL clock parameters
according to the fastest operating clock of the I2C hardware block.
And if that's the case, that calculation should be done just once
at driver-module-init time.

This patch moves ICCH/ICCL calculating part from activate_ch() into
sh_mobile_i2c_init(), and call it from sh_mobile_i2c_probe().

Note that sh_mobile_i2c_init() just prepares clock parameters using
the clock rate and platform data provided, but does _not_ make any
hardware I/O accesses.  We don't have to care about run-time PM
maintenance here.

Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 08:57:16 +01:00
Wolfram Sang
16c4c52435 bindings: i2c: use consistent naming for i2c binding descriptions
Filenames of devictree binding documentation seems to be arbitrary and
for me it is unneeded hazzle to find the corresponding documentation for
a specific driver.

Naming the description the same as the driver is a lot easier and makes
sense to me since the driver defines the binding it understands.

Also, remove a reference in one source to the binding documentation, since path
information easily gets stale.

Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-11-15 15:57:07 +00:00
Wolfram Sang
27e0fbefa5 i2c: omap: don't save a value only needed for read-clearing
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
2012-11-14 19:52:12 +01:00
Shubhrajyoti D
ca85e248b6 i2c: omap: cleanup the sysc write
Currently after the reset the sysc is written with hardcoded values.
The patch reads the sysc register and writes back the same value
after reset.

- Some unnecessary rev checks can be optimised.
- Also due to whatever reason the hwmod flags are changed
we will not reset the values.
- In some of the cases the minor values of the 2430 register
is different(0x37) in that case the autoidle setting may be missed.

Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:43 +01:00
Shubhrajyoti D
554c96744a i2c: omap: Restore i2c context always
Currently the restore is done based on the flag
OMAP_I2C_FLAG_RESET_REGS_POSTIDLE.

This helps the following
- The driver is always capable of restoring regardless
of the off mode support being there or not.

- While testing omap2430 it is found that in case of certain
error paths (timeout) a reset is done. However the restore
never happens as it is dependent on the POSTIDLE flag.
The other option would be to call a restore in the reset
case. As there are only a few registers to be restored
the penalty in the idle case should not be much.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:42 +01:00
Shubhrajyoti D
d6c842ad56 i2c: omap: make reset a seperate function
Implement reset as a separate function.
This will enable us to make sure that we don't do the
calculation again on every transfer.
Also at probe the reset is not added as the hwmod is doing that
for us.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:42 +01:00
Shubhrajyoti D
95dd303266 i2c: omap: re-factor omap_i2c_init function
re-factor omap_i2c_init() so that we can re-use it for resume.
While at it also remove the bufstate variable as we write it
in omap_i2c_resize_fifo for every transfer.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:41 +01:00
Shubhrajyoti D
2c88ab8c5a ARM: i2c: omap: Remove the i207 errata flag
The commit [i2c: omap: use revision check for OMAP_I2C_FLAG_APPLY_ERRATA_I207]
uses the revision id instead of the flag. So the flag can be safely removed.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:40 +01:00
Shubhrajyoti D
cd10c74aee i2c: omap: remove the dtrev
The dtrev is used only for the comments. Remove the same and use
the scheme instead to know if it is version2.

Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:39 +01:00
Shubhrajyoti D
a748021ccb i2c: omap: use revision check for OMAP_I2C_FLAG_APPLY_ERRATA_I207
The errata i207 is enabled for 2430 and 3xxx. Use the revision check
to enable the erratum instead.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:39 +01:00
Shubhrajyoti D
47dcd0161a i2c: omap: Fix the revision register read
The revision register on OMAP4 is a 16-bit lo and a 16-bit
hi. Currently the driver reads only the lower 8-bits.
Fix the same by preventing the truncating of the rev register
for OMAP4.

Also use the scheme bit ie bit-14 of the hi register to know if it
is OMAP_I2C_IP_VERSION_2.

On platforms previous to OMAP4 the offset 0x04 is IE register whose
bit-14 reset value is 0, the code uses the same to its advantage.

Also since the omap_i2c_read_reg uses reg_map_ip_* a raw_readw is done
to fetch the revision register.

The dev->regs is populated after reading the rev_hi. A NULL check
has been added in the resume handler to prevent the access before
the setting of the regs.

Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:38 +01:00
Sebastien Guiriec
2d4b4520a5 i2c: omap: adopt pinctrl support
Some GPIO expanders need some early pin control muxing. Due to
legacy boards sometimes the driver uses subsys_initcall instead of
module_init. This patch takes advantage of defer probe feature
and pin control in order to wait until pin control probing before
GPIO driver probing. It has been tested on OMAP5 board with TCA6424
driver.

Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:37 +01:00
Felipe Balbi
d60ece5f01 i2c: omap: ensure writes to dev->buf_len are ordered
if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.

This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.

After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.

This patch has been tested with pandaboard for a few
iterations of the script mentioned above.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:44:37 +01:00
Felipe Balbi
aedc256dd0 i2c: omap: ensure writes to dev->buf_len are ordered
if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.

This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.

After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.

This patch has been tested with pandaboard for a few
iterations of the script mentioned above.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 17:43:03 +01:00
Paul Walmsley
9aadd70aed Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
This reverts commit 3db11feffc
(ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints).
This commit causes I2C timeouts to appear on several OMAP3430/3530-based
boards:

  http://marc.info/?l=linux-arm-kernel&m=135071372426971&w=2
  http://marc.info/?l=linux-arm-kernel&m=135067558415214&w=2
  http://marc.info/?l=linux-arm-kernel&m=135216013608196&w=2

and appears to have been sent for merging before one of its prerequisites
was merged:

  http://marc.info/?l=linux-arm-kernel&m=135219411617621&w=2

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 11:54:41 +01:00
Paul Walmsley
49839dc939 Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
This reverts commit 3db11feffc
(ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints).
This commit causes I2C timeouts to appear on several OMAP3430/3530-based
boards:

  http://marc.info/?l=linux-arm-kernel&m=135071372426971&w=2
  http://marc.info/?l=linux-arm-kernel&m=135067558415214&w=2
  http://marc.info/?l=linux-arm-kernel&m=135216013608196&w=2

and appears to have been sent for merging before one of its prerequisites
was merged:

  http://marc.info/?l=linux-arm-kernel&m=135219411617621&w=2

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 11:51:15 +01:00
Ludovic Desroches
0d852fe4d2 i2c: at91: fix SMBus quick command
The driver claims to support SMBus quick command but it was not the
case. This patch fixes this issue. Without it, i2cdetect finds imaginary
devices. And with some IP versions, trying to send 0 byte can cause
issue when writing data to an EEPROM.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

[wsa: improved the commit message]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 10:33:21 +01:00
Ludovic Desroches
7c3fe64d13 i2c: at91: fix SMBus quick command
The driver claims to support SMBus quick command but it was not the
case. This patch fixes this issue. Without it, i2cdetect finds imaginary
devices. And with some IP versions, trying to send 0 byte can cause
issue when writing data to an EEPROM.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

[wsa: improved the commit message]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 10:28:28 +01:00
Bo Shen
58a7371a4d i2c: i2c-gpio: fix name issue with multiple i2c gpio nodes
When having multiple i2c-gpio nodes, the name for each is same.
So add the patch to fix it.

The adap->name printing information was added by myself

without this patch the log information is as following
---<8---
adap->name = i2c-gpio-1
i2c-gpio i2c.2: using pins 30 (SDA) and 31 (SCL)
adap->name = i2c-gpio-1
i2c-gpio i2c.3: using pins 64 (SDA) and 65 (SCL)
--->8---

with this patch, the log information is as following
---<8---
adap->name = i2c.2
i2c-gpio i2c.2: using pins 30 (SDA) and 31 (SCL)
adap->name = i2c.3
i2c-gpio i2c.3: using pins 64 (SDA) and 65 (SCL)
--->8---

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

[wsa: minor fixes to the commit mesage]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-14 09:56:43 +01:00
Guenter Roeck
aa1e3e81e7 i2c-mux-pinctrl: Fix probe error path
When allocating the memory for i2c busses, the code checked the wrong
variable and thus never detected if there was a memory error.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-11-13 22:27:19 +01:00
Thierry Reding
970d494c32 i2c: ocores: Use devm_request_and_ioremap()
Replacing the devm_request_mem_region() and devm_ioremap_nocache() calls
by a single call to devm_request_and_ioremap() simplifies the code.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-13 12:16:24 +01:00
Wolfram Sang
45fd5e4ad2 i2c: rcar: fix section mismatch
Give the driver struct a name according to the 'standard' to fix:

WARNING: vmlinux.o(.data+0x11798): Section mismatch in reference from the variable rcar_i2c_drv to the function .devinit.text:rcar_i2c_probe()
...
WARNING: vmlinux.o(.data+0x1179c): Section mismatch in reference from the variable rcar_i2c_drv to the function .devexit.text:rcar_i2c_remove()

Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
2012-11-13 11:24:15 +01:00
Arnd Bergmann
b5932cc839 Merge branch 'cleanups/dma' into next/cleanup
Separate patches from Marek Szyprowski <m.szyprowski@samsung.com>:

Commit e9da6e9905 ("ARM: dma-mapping: remove custom consistent dma
region") replaced custom consistent memory handling, so setting
consistent dma memory size is not longer required. This patch series
cleans sub-architecture platform code to remove all calls to the
obsolated init_consistent_dma_size() function and finally removes the
init_consistent_dma_size() stub itself.

* cleanups/dma:
  ARM: at91: remove obsoleted init_consistent_dma_size()
  ARM: u300: remove obsoleted init_consistent_dma_size()
  ARM: dma-mapping: remove init_consistent_dma_size() stub
  ARM: shmobile: remove obsoleted init_consistent_dma_size()
  ARM: davinci: remove obsoleted init_consistent_dma_size()
  ARM: samsung: remove obsoleted init_consistent_dma_size()

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-11-13 10:14:38 +01:00
Kuninori Morimoto
b53f4baf8b i2c: rcar: used devm_request_and_ioremap() instead of devm_ioremap()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-13 09:27:28 +01:00
Chuansheng Liu
cf7505ef9c i2c: nomadik: Fix the usage of wait_for_completion_timeout
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.

So the condition "ret < 0" or "ret >= 0" is pointless.

Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-12 18:21:55 +01:00
Linus Torvalds
209c510e36 Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
 "Two patches are usual stuff.

  The bigger patch is needed to correct a wrong decision made in this
  merge window.  We hoped to get the PIOQUEUE mode in the mxs driver
  working with DMA, but it turned out to be too broken (leading to data
  loss), so we now think it is best to remove it entirely and work only
  with DMA now.  The patch should be in 3.7.  IMO, so users never get
  the chance to use both modes in parallel."

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c: tegra: set irq name as device name
  i2c-nomadik: Fixup clock handling
  i2c: mxs: remove broken PIOQUEUE support
2012-11-03 15:14:54 -07:00
Laxman Dewangan
91b370a0db i2c: tegra: set irq name as device name
When watching the irqs name of tegra i2c, all instances
irq name shows as tegra_i2c.

Passing the device name properly to have the irq names with
instance like tegra-i2c.0, tegra-i2c.1 etc.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-02 10:52:52 +01:00
Philippe Begnic
817315f574 i2c-nomadik: Fixup clock handling
Make sure to clk_prepare as well as clk_enable.

Signed-off-by: Philippe Begnic <philippe.begnic@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-02 10:52:52 +01:00
Wolfram Sang
82fa63bd6b i2c: mxs: remove broken PIOQUEUE support
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2012-11-02 10:52:32 +01:00
Jean Delvare
28901f5794 i2c-i801: Fix comment
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-28 21:37:01 +01:00
Jean Delvare
79e3e5b894 i2c-i801: Simplify dependency towards GPIOLIB
Arbitrarily selecting GPIOLIB causes trouble on some architectures,
so don't do that. Instead, just make the optional multiplexing code
depend on CONFIG_I2C_MUX_GPIO instead of CONFIG_I2C_MUX for now. We
can revisit if the i2c-i801 driver ever supports other multiplexing
flavors.

Also make that optional code depend on DMI, as it won't do anything
without that.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
2012-10-28 21:37:01 +01:00
Jean Delvare
31d178bffc i2c-stub: Move to drivers/i2c
Move the i2c-stub driver to drivers/i2c, to match the Kconfig entry.
This is less confusing that way.

I also fixed all checkpatch warnings and errors.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Huewe <peterhuewe@gmx.de>
2012-10-28 21:37:00 +01:00
Shawn Guo
5bdfba29f1 i2c: imx: remove cpu_is_xxx by using platform_device_id
This is some amount of work left/forgot from device tree conversion.
Instead of checking cpu_is_xxx to determine the controller type, the
driver should use platform_device_id, which should match the device
tree compatible string.

The patch changes the driver to use platform_device_id rather than
cpu_is_xxx to determine the controller type/version.  It also updates
the platform code and device tree source accordingly.

As the result, mach/hardware.h inclusion gets removed from the driver.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
2012-10-15 10:03:15 +08:00
Linus Torvalds
12250d843e Merge branch 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux
Pull i2c-embedded changes from Wolfram Sang:
 "The changes for i2c-embedded include:

   - massive rework of the omap driver
   - massive rework of the at91 driver.  In fact, the old driver gets
     removed; I am okay with this approach since the old driver was
     depending on BROKEN and its limitations made it practically
     unusable, so people used bitbanging instead.  But even if there are
     users, there is no platform_data or module parameter which would
     need to be converted.  It is just another driver doing I2C
     transfers, just way better.  Modifications of arch/arm/at91 related
     files have proper acks from the maintainer.
   - new driver for R-Car I2C
   - devicetree and generic_clock conversions and fixes
   - usual driver fixes and changes.

  The rework patches have come a long way and lots of people have been
  involved in creating/testing them.  Most patches have been in
  linux-next at least since 3.6-rc5.  A few have been added in the last
  week, I have to admit.

  An unexpected (but welcome :)) peak in private life is the cause for
  that.  The "late" patches shouldn't cause any merge conflicts and I
  will have a special eye on them during the stabilization phase.  This
  is an exception and I want to have the patches in place properly in
  time again for the next kernels."

* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
  MXS: Implement DMA support into mxs-i2c
  i2c: add Renesas R-Car I2C driver
  i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
  ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
  i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
  i2c: algo: pca: Fix chip reset function for PCA9665
  i2c: mpc: Wait for STOP to hit the bus
  i2c: davinci: preparation for switch to common clock framework
  omap-i2c: fix incorrect log message when using a device tree
  i2c: omap: sanitize exit path
  i2c: omap: switch over to autosuspend API
  i2c: omap: remove unnecessary pm_runtime_suspended check
  i2c: omap: switch to threaded IRQ support
  i2c: omap: remove redundant status read
  i2c: omap: get rid of the "complete" label
  i2c: omap: resize fifos before each message
  i2c: omap: simplify IRQ exit path
  i2c: omap: always return IRQ_HANDLED
  i2c: omap: simplify errata check
  i2c: omap: bus: add a receiver flag
  ...
2012-10-11 10:27:51 +09:00
Marek Vasut
62885f59a2 MXS: Implement DMA support into mxs-i2c
This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.

Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>

[wsa: rebased to 3.6-rc7]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-10-08 12:47:33 +02:00
Wolfram Sang
102084d3d3 Linux 3.6-rc7
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
 LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
 u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
 xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
 i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
 GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
 =0v2l
 -----END PGP SIGNATURE-----

Merge tag 'v3.6-rc7' into i2c-embedded/for-next

Linux 3.6-rc7

Needed to get updates from i2c-embedded/for-current into i2c-embedded/for-next
2012-10-08 12:46:32 +02:00
Kuninori Morimoto
6ccbe60713 i2c: add Renesas R-Car I2C driver
R-Car I2C is similar with SH7760 I2C.
But the SH7760 I2C driver had many workaround operations, since H/W had bugs.
Thus, it was pointless to keep compatible between SH7760 and R-Car I2C drivers.
This patch creates new Renesas R-Car I2C driver.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-10-08 12:46:25 +02:00
Linus Torvalds
d8dc91b753 Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pul ACPI & Power Management updates from Len Brown:
 - acpidump utility added
 - intel_idle driver now supports IVB Xeon
 - turbostat utility can now count SMIs
 - ACPI can now bind to USB3 hubs
 - misc fixes

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (49 commits)
  ACPI: Add new sysfs interface to export device description
  ACPI: Harden acpi_table_parse_entries() against BIOS bug
  tools/power/turbostat: add option to count SMIs, re-name some options
  tools/power turbostat: add [-d MSR#][-D MSR#] options to print counter deltas
  intel_idle: enable IVB Xeon support
  tools/power turbostat: add [-m MSR#] option
  tools/power turbostat: make -M output pretty
  tools/power turbostat: print more turbo-limit information
  tools/power turbostat: delete unused line
  tools/power turbostat: run on IVB Xeon
  tools/power/acpi/acpidump: create acpidump(8), local make install targets
  tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
  ACPI: run _OSC after ACPI_FULL_INITIALIZATION
  tools/power/acpi/acpidump: create acpidump(8), local make install targets
  tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
  tools/power/acpi/acpidump: version 20071116
  tools/power/acpi/acpidump: version 20070714
  tools/power/acpi/acpidump: version 20060606
  tools/power/acpi/acpidump: version 20051111
  xo15-ebook: convert to module_acpi_driver()
  ...
2012-10-08 07:14:06 +09:00
Thomas Abraham
d3b64c5934 i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.

Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-10-06 15:57:25 +02:00
Jean Pihet
3db11feffc ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
Convert the driver from the outdated omap_pm_set_max_mpu_wakeup_lat
API to the new PM QoS API.
Since the constraint is on the MPU subsystem, use the PM_QOS_CPU_DMA_LATENCY
class of PM QoS. The resulting MPU constraints are used by cpuidle to
decide the next power state of the MPU subsystem.

The I2C device latency timing is derived from the FIFO size and the
clock speed and so is applicable to all OMAP SoCs.

Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-10-06 13:43:38 +02:00
Lee Jones
43fea5813c i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
Here we apply the bindings required for successful Device Tree
probing of the i2c-nomadik driver.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-10-06 13:20:33 +02:00
Thomas Kavanagh
a76e7c6821 i2c: algo: pca: Fix chip reset function for PCA9665
The parameter passed to pca9665_reset is adap->data (which is bus driver
specific), not i2c_algp_pca_data *adap. pca9665_reset expects it to be
i2c_algp_pca_data *adap. All other wrappers from the algo call back to
the bus driver, which knows to handle its custom data. Only pca9665_reset
resides inside the algorithm code and does not know how to handle a custom
data structure. This can result in a kernel crash.

Fix by re-factoring pca_reset() from a macro to a function handling chip
specific code, and only call adap->reset_chip() if the chip is not PCA9665.

Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-10-06 13:14:36 +02:00
Daniel J Blueman
c415b303a7 i2c-piix4: Fix build failure
Fix build failure in Intel PIIX4 I2C driver.

Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org [v3.6]
2012-10-05 22:23:55 +02:00
Jean Delvare
f82b86267a i2c-i801: Let i2c-mux-gpio find the GPIO chip
Now that i2c-mux-gpio is able to find the GPIO chip by itself, we can
delegate this task. The great thing here is that i2c-mux-gpio can
defer device probing until the gpio chip is available, so we no longer
depend on the module loading order.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:54 +02:00
Jean Delvare
e7ee514058 i2c-mux-gpio: Add support for dynamically allocated GPIO pins
The code instantiating an i2c-mux-gpio platform device doesn't
necessarily know in advance the GPIO pin numbers it wants to use. If
pins are on a GPIO device which gets its base GPIO number assigned
dynamically at run-time, the values can't be hard-coded.

In that case, let the caller tell i2c-mux-gpio the name of the GPIO
chip and the (relative) GPIO pin numbers to use. At probe time, the
i2c-mux-gpio driver will look for the chip and apply the proper offset
to turn relative GPIO pin numbers to absolute GPIO pin numbers.

The same could be (and was so far) done on the caller's end, however
doing it in i2c-mux-gpio has two benefits:
* It avoids duplicating the code on every caller's side (about 30
  lines of code.)
* It allows for deferred probing for the muxed part of the I2C bus
  only. If finding the GPIO chip is the caller's responsibility, then
  deferred probing (if the GPIO chip isn't there yet) will not only
  affect the mux and the I2C bus segments behind it, but also the I2C
  bus trunk.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-05 22:23:54 +02:00
Maxime Ripard
2614a85941 i2c-mux-gpio: Use devm_kzalloc instead of kzalloc
Use the devm_kzalloc managed function to stripdown the error and remove
code.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:53 +02:00
Jean Delvare
3ad7ea18ae i2c-i801: Support SMBus multiplexing on Asus Z8 series
Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.

On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.

The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.

Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.

At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:53 +02:00
Jean Delvare
01d56a6aa1 i2c-viapro: Add VIA VX900 device ID
The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.

This closes kernel bug #43096.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:53 +02:00
Jean Delvare
7fe442a1a5 i2c-parport: i2c_parport_irq can be static
i2c_parport_irq is only called internally so it can be static.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:53 +02:00
Jean Delvare
bccd780f86 i2c-designware: i2c_dw_xfer_msg can be static
i2c_dw_xfer_msg is only called internally so it can be static. It
original was, before the driver split. No idea why it was changed at
that time.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2012-10-05 22:23:53 +02:00
Jim Cromie
401e72b55d i2c/scx200_*: Replace printks with pr_<level>s
Replace printks with pr_<level>s, add pr_fmt()s to replace NAMEs

Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:52 +02:00
Peter Huewe
3ddb59d4bc i2c: Make I2C available on UML
Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.

The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.

[JD: Some adjustments.]

[Heiko Carstens: Keep I2C disabled on S390.]

Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:52 +02:00
Shubhrajyoti D
230da09435 i2c: Convert struct i2c_msg initialization to C99 format
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.

Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:52 +02:00
Julia Lawall
71b578452e i2c-smbus: Convert kzalloc to devm_kzalloc
Converting kzalloc to devm_kzalloc simplifies the code and ensures that the
result, alert, is freed after the irq allocated by the subsequent
devm_request_irq.  This in turn ensures that when an interrupt can be
triggered, the alert structure is still available.

The problem of a free after a devm_request_irq was found using the
following semantic match (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression e1,e2,x,a,b,c,d;
identifier free;
position p1,p2;
@@

  devm_request_irq@p1(e1,e2,...,x)
  ... when any
      when != e2 = a
      when != x = b
  if (...) {
    ... when != e2 = c
        when != x = d
    free@p2(...,x,...);
    ...
    return ...;
  }
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:52 +02:00
Jean Delvare
eee543e824 i2c-mux: Add support for device auto-detection
Let I2C bus segments behind multiplexers have a class. This allows for
device auto-detection on these segments. As long as parent segments
don't share the same class, it should be fine.

I implemented support in drivers i2c-mux-gpio and i2c-mux-pca954x. I
left i2c-mux-pca9541 and i2c-mux-pinctrl alone for the moment as I
don't know if this feature makes sense for the use cases of these
drivers.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Cc: Rodolfo Giometti <giometti@linux.it>
2012-10-05 22:23:51 +02:00
Fengguang Wu
125c4c706b idr: rename MAX_LEVEL to MAX_IDR_LEVEL
To avoid name conflicts:

  drivers/video/riva/fbdev.c:281:9: sparse: preprocessor token MAX_LEVEL redefined

While at it, also make the other names more consistent and add
parentheses.

[akpm@linux-foundation.org: repair fallout]
[sfr@canb.auug.org.au: IB/mlx4: fix for MAX_ID_MASK to MAX_IDR_MASK name change]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: walter harms <wharms@bfs.de>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-10-06 03:04:56 +09:00
Linus Torvalds
9cd11c0c47 ARM: soc: multiplatform enablement
This is a pretty significant branch. It's the introduction of the
 first multiplatform support on ARM, and with this (and the later
 branch) merged, it is now possible to build one kernel that contains
 support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
 platforms will be convered over in the next few releases.
 
 Two critical last things had to be done for this to be practical and
 possible:
 * Today each platform has its own include directory under
   mach-<mach>/include/mach/*, and traditionally that is where a lot of
   driver/platform shared definitions have gone, such as platform data
   structures. They now need to move out to a common location instead,
   and this branch moves a large number of those out to
   include/linux/platform_data.
 * Each platform used to list the device trees to compile for its
   boards in mach-<mach>/Makefile.boot.
 
 Both of the above changes will mean that there are some merge
 conflicts to come (and some to resolve here). It's a one-time move and
 once it settles in, we should be good for quite a while. Sorry for the
 overhead.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJQaO7aAAoJEIwa5zzehBx3bUIP/02U8PhkHJJrrowyIsWRBOql
 7LPJ53PRRgrpBdmEGzFD3TO3zaNyrjQRbYgNDvzHMO6NAMNvdRFouuWYjO11/tuB
 i32zssXCC+eUOEgbAo/U/lYq+UOvqw9gv6mU+3+i3OcGEhdKOaoT/DSLPQC4hoDm
 222TeLfFB3HJXu5n720dEQ9V3fO6TS1+bbh8TU3cjHqzceXsOrffZqOA5CQxUcRr
 KWwOjA0nALDwWcqgv45GJNwY3GTyAQ/hPMQavnuWK0voJ+qUYk5HftKocAK7C+py
 0T0OFOAHTwtyhvzJBxLC84M6Ox465BYXyeNjIB+2nG/Um9+mDoP0dnWpGy4c7DMU
 P5hyqbeLGeqjUXQuYtRmgMMc3UeHKoUGAfXW9eMsjLa6/M4NLGv//7E7LbZPpgMZ
 obkjwuesmcaYn/FRyj/yFmC35YlF4oCLziVzEtURZw3eKHHSUlhkTDSMNnkcZ0kZ
 Vv7kFxnD2Y46ixiwSJv30ErQnVkgI3MdqDlDxkE8r5+phYuK4gCrNaJtiwRh/oNw
 cFhpPxKuA0sJ9b6YRTzjC45eT/XZomEEr/uifCFeRNaCquyjYP00Mm8F0flSqwx9
 zi+emzPAwNmk1bvxMUM/idGnaj0V4p+BAYUAvkbSoqU1p1flzyhU88fGTSIyKOt6
 K5TCDS2v5hrVykK9TDwl
 =Tc6y
 -----END PGP SIGNATURE-----

Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM soc multiplatform enablement from Olof Johansson:
 "This is a pretty significant branch.  It's the introduction of the
  first multiplatform support on ARM, and with this (and the later
  branch) merged, it is now possible to build one kernel that contains
  support for highbank, vexpress, mvebu, socfpga, and picoxcell.  More
  platforms will be convered over in the next few releases.

  Two critical last things had to be done for this to be practical and
  possible:
   * Today each platform has its own include directory under
     mach-<mach>/include/mach/*, and traditionally that is where a lot
     of driver/platform shared definitions have gone, such as platform
     data structures.  They now need to move out to a common location
     instead, and this branch moves a large number of those out to
     include/linux/platform_data.
   * Each platform used to list the device trees to compile for its
     boards in mach-<mach>/Makefile.boot.

  Both of the above changes will mean that there are some merge
  conflicts to come (and some to resolve here).  It's a one-time move
  and once it settles in, we should be good for quite a while.  Sorry
  for the overhead."

Fix conflicts as per Olof.

* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
  ARM: add v7 multi-platform defconfig
  ARM: msm: Move core.h contents into common.h
  ARM: highbank: call highbank_pm_init from .init_machine
  ARM: dtb: move all dtb targets to common Makefile
  ARM: spear: move platform_data definitions
  ARM: samsung: move platform_data definitions
  ARM: orion: move platform_data definitions
  ARM: vexpress: convert to multi-platform
  ARM: initial multiplatform support
  ARM: mvebu: move armada-370-xp.h in mach dir
  ARM: vexpress: remove dependency on mach/* headers
  ARM: picoxcell: remove dependency on mach/* headers
  ARM: move all dtb targets out of Makefile.boot
  ARM: picoxcell: move debug macros to include/debug
  ARM: socfpga: move debug macros to include/debug
  ARM: mvebu: move debug macros to include/debug
  ARM: vexpress: move debug macros to include/debug
  ARM: highbank: move debug macros to include/debug
  ARM: move debug macros to common location
  ARM: make mach/gpio.h headers optional
  ...
2012-10-01 19:11:38 -07:00
Linus Torvalds
8f446a7a06 ARM: soc: driver specific changes
- A long-coming conversion of various platforms to a common LED
   infrastructure
 - AT91 is moved over to use the newer MCI driver for MMC
 - Pincontrol conversions for samsung platforms
 - DT bindings for gscaler on samsung
 - i2c driver fixes for tegra, acked by i2c maintainer
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJQaO48AAoJEIwa5zzehBx3excP/ieEkRhvfnWxdYST6ekvGIQr
 nEyskOh2rVjgYKmSXUJyKSbvG+7bZ8VIxvPvojeAJ/R84pTFMzbR2F0CaPKzAuSW
 inDt6c0Bnx1NZlfUTAoXcz7feyq9zHYNs9BCLoPU0bYNchCCqcWSKzqnpXk2ph/P
 LFnmNa0j6a4E3QJYAjM2zFvc3Tgk+MWTq1fWwNFvsWTh2WbQtmB/iGnzT5Xs4XQh
 u1SSx5tz0lcF5zQRGmJhXgL5+nnIP4sRwRUBAkpe3Gv5cM6WBVEBRDANa5QpbUL2
 RXK5YyCTIln2Me4bPk32zEBLjiZ/WXbmiA2uwoqVgy6XToubemDXd0PtKmjj5tZ1
 BkTD1DND7BKBEQnJj/GBECEdvx2FbrKfruoPcJHvXPZ7Svn5Dt/MWYJQIkRFkuhL
 zlVNoDGWlU8nScGrgmTM56UvWmGWC3UFsWSgdVQNfW9yEva+G1FvRUwUH02Ip5Ad
 4r28JFIn6zyjtM99ZHipU6C6Rze2ordC7fl5X5LBLkVOobioblxCAhIhcqkhfKsk
 rFriNsdfYs7SrJA7mK7GzvaMEJgp/5o1noJKXI7ZBcLI8yYagzbQbPu/vGi6G6d3
 0xC7NaTEJbtoXoDAtmtilLRxmw0YCXgVBBGua0K2YKpcRwnzCHNbV4gsLMnDuOXS
 HP4M96LxLHJlLGCxhEme
 =ck7M
 -----END PGP SIGNATURE-----

Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM soc driver specific changes from Olof Johansson:
 - A long-coming conversion of various platforms to a common LED
   infrastructure
 - AT91 is moved over to use the newer MCI driver for MMC
 - Pincontrol conversions for samsung platforms
 - DT bindings for gscaler on samsung
 - i2c driver fixes for tegra, acked by i2c maintainer

Fix up conflicts as per Olof.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  drivers: bus: omap_l3: use resources instead of hardcoded irqs
  pinctrl: exynos: Fix wakeup IRQ domain registration check
  pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
  pinctrl: exynos: Correct the detection of wakeup-eint node
  pinctrl: exynos: Mark exynos_irq_demux_eint as inline
  pinctrl: exynos: Handle only unmasked wakeup interrupts
  pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
  pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
  drivers: bus: Move the OMAP interconnect driver to drivers/bus/
  i2c: tegra: dynamically control fast clk
  i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
  ARM: tegra: clock: remove unused clock entry for i2c
  ARM: tegra: clock: add connection name in i2c clock entry
  i2c: tegra: pass proper name for getting clock
  ARM: tegra: clock: add i2c fast clock entry in clock table
  ARM: EXYNOS: Adds G-Scaler device from Device Tree
  ARM: EXYNOS: Add clock support for G-Scaler
  ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
  ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
  ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
  ...
2012-10-01 18:46:13 -07:00
Linus Torvalds
61464c8357 ARM: soc: general cleanups
This is a large branch that contains a handful of different cleanups:
 
 - Fixing up the I/O space remapping on PCI on ARM. This is a series
   from Rob Herring that restructures how all pci devices allocate I/O
   space, and it's part of the work to allow multiplatform kernels.
 - A number of cleanup series for OMAP, moving and removing some
   headers, sparse irq rework and in general preparation for
   multiplatform.
 - Final removal of all non-DT boards for Tegra, it is now
   device-tree-only!
 - Removal of a stale platform, nxp4008. It's an old mobile chipset
   that is no longer in use, and was very likely never really used with
   a mainline kernel. We have not been able to find anyone interested
   in keeping it around in the kernel.
 - Removal of the legacy dmaengine driver on tegra
 
 + A handful of other things that I haven't described above.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJQaO1fAAoJEIwa5zzehBx3IPgP/jxoO1flVGNVf0reqqyDro/w
 prZmp8cNVH9uv8xG9n9vawObrMQ8M6jCJ449fEWuAZ58EXrpIPd0kkm/MOmxp8K1
 LNs+q2aXxWpD488+b3RK55g3fksqZutTbn3y6HNuCoLG9l8yT/95KX4IIzfEP2Ch
 1TCNHdkTbf37nTBOmKN0x1kahGpWDrOkf9ysHQq+DXAGF4uwNwtR194dqz3HbDND
 hZqRq7qCLn9OwGRGNicPFoB6UcxwZ/+/+u5sX7nqPGoiPofg977mhWk1DFO15EM3
 S+A6g0dZ+XLsL+fFtOl4snSmrG5Et6qTOP0/ItQJgTG+5YdCS09ohCWJwRCBHbgj
 M5arOkyGFdVAlvX7cUux374sMe0AcqUsEmt79mYuBpIE+pBJaRUoCgDcs9FDZeUB
 U6WcE4AkxMtW7DtmVW+mF4ls9/K6cRXgWMuHCUmt1o3m3Ly9ITT7j+ntXnD9nuYk
 ndoVLR6Vxk2BzlkD0JEtg7FRAS9Wgo2DBix05qM1Qkut2iIZRhFQlqJQpNbeNdii
 /3Lg/hqpAVTZKGCd+paegHez61meyFz2PB2IiE0JKANhKHRCWTWRGgKIXkGyCiXk
 wJ2iRCOlMEpmpJgCBzfI32ER/hnW4s64iDjgksEwz6pEt7xCbhwgmwrpf0H0KsSF
 rLroHOMqyISd/Ha52Vin
 =ck1u
 -----END PGP SIGNATURE-----

Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM soc general cleanups from Olof Johansson:
 "This is a large branch that contains a handful of different cleanups:

   - Fixing up the I/O space remapping on PCI on ARM.  This is a series
     from Rob Herring that restructures how all pci devices allocate I/O
     space, and it's part of the work to allow multiplatform kernels.
   - A number of cleanup series for OMAP, moving and removing some
     headers, sparse irq rework and in general preparation for
     multiplatform.
   - Final removal of all non-DT boards for Tegra, it is now
     device-tree-only!
   - Removal of a stale platform, nxp4008.  It's an old mobile chipset
     that is no longer in use, and was very likely never really used
     with a mainline kernel.  We have not been able to find anyone
     interested in keeping it around in the kernel.
   - Removal of the legacy dmaengine driver on tegra

  + A handful of other things that I haven't described above."

Fix up some conflicts with the staging tree (and because nxp4008 was
removed)

* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
  ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
  ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
  ARM: mmp: using for_each_set_bit to simplify the code
  ARM: tegra: harmony: fix ldo7 regulator-name
  ARM: OMAP2+: Make omap4-keypad.h local
  ARM: OMAP2+: Make l4_3xxx.h local
  ARM: OMAP2+: Make l4_2xxx.h local
  ARM: OMAP2+: Make l3_3xxx.h local
  ARM: OMAP2+: Make l3_2xxx.h local
  ARM: OMAP1: Move irda.h from plat to mach
  ARM: OMAP2+: Make hdq1w.h local
  ARM: OMAP2+: Make gpmc-smsc911x.h local
  ARM: OMAP2+: Make gpmc-smc91x.h local
  ARM: OMAP1: Move flash.h from plat to mach
  ARM: OMAP2+: Make debug-devices.h local
  ARM: OMAP1: Move board-voiceblue.h from plat to mach
  ARM: OMAP1: Move board-sx1.h from plat to mach
  ARM: OMAP2+: Make omap-wakeupgen.h local
  ARM: OMAP2+: Make omap-secure.h local
  ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
  ...
2012-10-01 18:19:05 -07:00
Olof Johansson
e3a66aa33a Merge branch 'multiplatform/platform-data' into next/multiplatform
* multiplatform/platform-data:
  ARM: spear: move platform_data definitions
  ARM: samsung: move platform_data definitions
  ARM: orion: move platform_data definitions
  ARM: nomadik: move platform_data definitions
  ARM: w90x900: move platform_data definitions
  ARM: vt8500: move platform_data definitions
  ARM: tegra: move sdhci platform_data definition
  ARM: sa1100: move platform_data definitions
  ARM: pxa: move platform_data definitions
  ARM: netx: move platform_data definitions
  ARM: msm: move platform_data definitions
  ARM: imx: move platform_data definitions
  ARM: ep93xx: move platform_data definitions
  ARM: davinci: move platform_data definitions
  ARM: at91: move platform_data definitions

Conflicts due to removed files:
	arch/arm/mach-tegra/board-harmony.c
	arch/arm/mach-tegra/board-trimslice.c

Conflicts due to code removal:
	arch/arm/mach-tegra/board-paz00.c

Context conflicts in:
	drivers/mmc/host/sdhci-tegra.c
	drivers/net/irda/pxaficp_ir.c

Signed-off-by: Olof Johansson <olof@lixom.net>
2012-09-22 01:07:21 -07:00
Olof Johansson
b536661bb0 Merge branch 'v3.7-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/fixes-non-critical
A few non-critical fixes/cleanups for samsung platforms.

* 'v3.7-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: SAMSUNG: Add missing variable declaration in s3c64xx_spi1_set_platdata()
  ARM: S3C24XX: removes unnecessary semicolon
  ARM: S3C24xx: delete double assignment
  ARM: EXYNOS: fix address for EXYNOS4 MDMA1
  ARM: EXYNOS: fixed SYSMMU setup definition to mate parameter name
  + sync to 3.6-rc6
2012-09-21 22:54:15 -07:00
Mika Westerberg
20420500cb i2c-scmi: convert to module_acpi_driver()
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
2012-09-21 13:39:56 -04:00
Olof Johansson
32dec75349 ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
 driver since v3.6-rcX. This series flips Tegra's defconfig to enable
 dmaengine rather than the legacy driver, and removes the legacy driver
 and all client code.
 
 The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
 ASoC Tegra PCM driver that's required for audio to work correctly when
 using dmaengine.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.10 (GNU/Linux)
 
 iQIcBAABAgAGBQJQV0gxAAoJEMzrak5tbycx9mIP/0uU4fVrAyIgbRkJ7nrPS/K7
 vRKEfYJlXqr4zM79i3flpD/QPK6ImWcj0RptrdU3851yjVGkSehp8wbozKoBVDXQ
 ZqPEBG039Vshmum/AD6Km3LSl4LBYurNJp/OC7ms5r0jIsU2IxZYaoofLGPXmgwn
 LTlsG35Y/Bug6P4bbSNPhR/9CFAe695oQgvkIMnYROwVZTmQwu7Xh1CE2moKMEJN
 top1Z3tZ+gtbb84eU1KR9BSNXAhQi7S7d4vWJe3RjnrhuSTVMIxiyNZSFjt8DrLL
 7THzpmY/K2qV9k6CAO7bTl9X6m9cw8j+IbN6Ljc1NjbBiMcFe3TQRwFXicmt/Pma
 VPjppGIfTUzC9WJI5Tj8GOV6I6B6X5oCSILcXjeJpNE3TEvdLnVXhiclbhiVuB/0
 j9x0+w1SMfRr8RtsMvZyZHy1XQ+WJg/rXojGxLEsKJrZmmJ7yRkfqIr/Q9nSrh87
 KYHhy8lsOuSPXq1qEVKQLwenc1VPbbDcDow1fBURPmz1CFCvNnR/mWtY2uCu5gk/
 XPcqZu5I/T7DlrNGTfYCZbOow67tfHgAxW5MYLPXV+Fqkj1l9EimUGW5fIq7S6bA
 2ouTuCS1e79d9kFLjgAzdbfqtdjy93v7G5vlBV7gUIrMg5PtGnQvQK9ab/YzasOt
 XtP5p/eeV8NDo3MCw3+b
 =4eRL
 -----END PGP SIGNATURE-----

Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup

ARM: tegra: switch to dmaengine

The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.

* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
  ASoC: tegra: remove support of legacy DMA driver based access
  spi: tegra: remove support of legacy DMA driver based access
  ARM: tegra: apbio: remove support of legacy DMA driver based access
  ARM: tegra: dma: remove legacy APB DMA driver
  ARM: tegra: config: enable dmaengine based APB DMA driver
  + sync to 3.6-rc6
2012-09-20 19:57:38 -07:00
Arnd Bergmann
436d42c61c ARM: samsung: move platform_data definitions
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the samsung include directories

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
2012-09-19 17:42:18 +02:00
Linus Torvalds
5b799dde31 Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
 "The last bunch of (typical) i2c-embedded driver fixes for 3.6.

  Also update the MAINTAINERS file to point to my tree since people keep
  asking where to find their patches."

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c: algo: pca: Fix mode selection for PCA9665
  MAINTAINERS: fix tree for current i2c-embedded development
  i2c: mxs: correctly setup speed for non devicetree
  i2c: pnx: Fix read transactions of >= 2 bytes
  i2c: pnx: Fix bit definitions
2012-09-14 17:55:57 -07:00
Joakim Tjernlund
0c25aefa35 i2c: mpc: Wait for STOP to hit the bus
mpc_i2c_stop() only initiates STOP but does not wait for it to
hit the I2C bus. This is a problem when using I2C devices which
uses fairly long clock stretching just before STOP if you also
have an i2c-mux which may switch to another bus before STOP has
been processed.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-14 16:01:04 +02:00
Thomas Kavanagh
5f71a3ef37 i2c: algo: pca: Fix mode selection for PCA9665
The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.

Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-14 15:25:22 +02:00
Murali Karicheri
2bdbfa9c4a i2c: davinci: preparation for switch to common clock framework
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare(). Until the platform is
switched to use the CONFIG_HAVE_CLK_PREPARE Kconfig variable, this just
adds a might_sleep() call and would work without any issues.

This will make it easy later to switch to common clk based implementation
of clk driver from DaVinci specific driver.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-14 15:20:33 +02:00
Arnd Bergmann
54ecf4f056 ARM: w90x900: move platform_data definitions
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the w90x900 include directories

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
2012-09-14 11:18:59 +02:00
Arnd Bergmann
82906b13a6 ARM: imx: move platform_data definitions
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the imx include directories

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
2012-09-14 11:17:21 +02:00
Arnd Bergmann
ec2a0833e5 ARM: davinci: move platform_data definitions
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.

This moves such data out of the davinci include directories

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
2012-09-14 11:16:54 +02:00
Laxman Dewangan
fd301cc4e5 i2c: tegra: dynamically control fast clk
Tegra I2C driver enables the fast clock during initialization
and does not disable till driver removed.
Enable this clock before transfer and disable after transfer done.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-09-13 11:40:30 -06:00
Laxman Dewangan
6ad068ed63 i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
Tegra20 i2c controller does not support the continue transfer
which implements the I2C_M_NOSTART functionality of i2c
protocol mangling.
Removing the I2C_M_NOSTART functionality support for Tegra20.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-09-13 11:40:30 -06:00
Laxman Dewangan
14e92bd4ff i2c: tegra: pass proper name for getting clock
Tegra's i2c controller require two clock sources named as
div_clk and fast_clk.
This change make sure that driver pass the correct clock's
name when it acquires clock handle. Also change the
variable name to reflect the correct clock handles.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-09-13 11:40:29 -06:00
Olof Johansson
1a87676206 Merge branch 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux into next/fixes-non-critical
From  "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>:

this is the 2nd version of this series whose goal is to make struct
of_device_id.data const. Conceptually a driver must not modify the data
contained there so making it const is the right thing.

v1 of this series was sent with Message-id:
1342182734-321-1-git-send-email-y. Changes since then are:
 - powerpc fixes
 - several new consts that were found by Arnd that are possible after
   patch 19.

Arnd suggested to take this series via arm-soc late for 3.6 in one go
because patch 19 depends on the former patches but is a precondition to
the latter and it fixes a few warnings. So getting it in via the
respective maintainer trees would need a much bigger coordination
effort. That means I prefer getting Acks over you taking the patch.

Vinod Koul already took
        dmaengine: at_hdmac: add a few const qualifiers
that is in next-20120723 as 7fd63ccdad now. Vinod, I don't follow your
pull requests, but assuming you didn't let it already pull for 3.6 I
suggest you drop it from your queue and I just take your Ack.

This series was build tested for arm (all defconfigs) and powerpc (all
defconfigs and an allyesconfig) and grep didn't find more issues. As
before it introduces a warning in drivers/regulator/twl-regulator.c.
This driver does modify its .of_match_table when a device is bound which
doesn't fits the concept of independant devices. Arnd noticed another
new warning in drivers/scsi/qlogicpti.c that isn't that easy to resolve,
because the pointer to (now) const data is passed as first argument to
scsi_host_alloc. To fix that properly struct Scsi_Host.hostt needs to
get a const, too. Alternatively I could introduce a cast removing the
const, but I don't like that.

* 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux: (25 commits)
  dma: tegra: make data used as *of_device_id.data const
  can: mpc5xxx_can: make data used as *of_device_id.data const
  macintosh/mediabay: make data used as *of_device_id.data const
  i2c/mpc: make data used as *of_device_id.data const
  mfd/da9052: make i2c_device_id array const
  powerpc/fsl_msi: drop unneeded cast to non-const pointer
  gpio/gpio-omap: make platformdata used as *of_device_id.data const
  of: add const to struct *of_device_id.data
  dma: tegra: make tegra_dma.chip_data a pointer to const data
  watchdog/mpc8xxx: add a const qualifier
  powerpc/celleb_pci: add a const qualifier
  powerpc/fsl_msi: add a const qualifier
  powerpc/83xx: add a const qualifier
  macintosh/mediabay: add a const qualifier
  mmc/omap_hsmmc: add a const qualifier
  i2c/mpc: add a const qualifier
  i2c/i2c-omap: add a const qualifier
  gpio/mpc8xxx: add a const qualifier
  gpio/gpio-omap.c: add a const qualifier
  misc/atmel_tc: make atmel_tc.tcb_config member point to const data

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: repulled a v3 version of the branch that rebased to add some more
acked-bys and added one more patch on top for tegra]
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-09-13 00:15:00 -07:00
Wolfram Sang
72ee734a67 i2c: mxs: correctly setup speed for non devicetree
Commit cd4f2d4 (i2c: mxs: Set I2C timing registers for mxs-i2c) only
covered the case for devicetree and made platform_data based boards
bail out with -EINVAL. Correctly support the latter one, too.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 17:55:22 +02:00
Roland Stigge
c076ada4e4 i2c: pnx: Fix read transactions of >= 2 bytes
On transactions with n>=2 bytes, the controller actually wrongly clocks in n+1
bytes. This is caused by the (wrong) assumption that RFE in the Status Register
is 1 iff there is no byte already ordered (via a dummy TX byte). This lead to
the implementation of synchronized byte ordering, e.g.:

Dummy-TX - RX - Dummy-TX - RX - ...

But since RFE actually stays high after some Dummy-TX, it rather looks like:

Dummy-TX - Dummy-TX - RX - Dummy-TX - RX - (RX)

The last RX byte is clocked in by the bus controller, but ignored by the kernel
when filling the userspace buffer.

This patch fixes the issue by asking for RX via Dummy-TX asynchronously.
Introducing a separate counter for TX bytes.

Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 17:52:44 +02:00
Roland Stigge
b3aafe80c8 i2c: pnx: Fix bit definitions
The I2C Control Register bits RFDAIE and RFFIE were mixed up. In addition to
this fix, this patch adds the missing bit DRSIE for completeness.

Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 17:52:38 +02:00
Florian Vaussard
c5d3cd6dc2 omap-i2c: fix incorrect log message when using a device tree
When booting using a device tree, the adapter number is dynamically
assigned after the log message is sent.
This patch modifies the log message to get a correct adapter id.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:54:14 +02:00
Felipe Balbi
0bdfe0cb80 i2c: omap: sanitize exit path
move the goto out label one line down, so that
it can be used when stat is read as zero. All
other exits, can be done with a break statement.

While at that, also break out as soon as we
complete draining IRQ, since at that time
we know we transferred everything there was
to be transferred.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:04:18 +02:00
Felipe Balbi
6d8451d55a i2c: omap: switch over to autosuspend API
this helps us reduce unnecessary pm transitions
in case we have another i2c message starting soon.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:04:10 +02:00
Felipe Balbi
e3a36b207f i2c: omap: remove unnecessary pm_runtime_suspended check
before starting any messages we call pm_runtime_get_sync()
which will make sure that by the time we program a transfer
and our IRQ handler gets called, we're not suspended
anymore.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:04:03 +02:00
Felipe Balbi
3b2f8f82da i2c: omap: switch to threaded IRQ support
for OMAP2, we can easily switch over to threaded
IRQs on the I2C driver. This will allow us to
spend less time in hardirq context.

Signed-off-by: Felipe Balbi <balbi@ti.com>
[Trivial formating changes]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:03:56 +02:00
Shubhrajyoti D
d741d0c792 i2c: omap: remove redundant status read
Currently omap_i2c_ack_stat doesn't use the stat variable.
After the read of the I2C_STAT_REG it is not used.
Remove the redundant read of the status register.

Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:03:48 +02:00
Felipe Balbi
b07be0f3b9 i2c: omap: get rid of the "complete" label
we can ack stat and complete the command from
the errata handling itself.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:03:41 +02:00
Felipe Balbi
dd74548dde i2c: omap: resize fifos before each message
This patch will try to avoid the usage of
draining feature by reconfiguring the FIFO
the start condition of each message based
on the message's size.

By doing that, we will be better utilizing
the FIFO when doing big transfers.

While at that also drop the now unneeded
check for dev->buf_len as we always know
the amount of data to be transmitted.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:03:34 +02:00
Felipe Balbi
4a7ec4eda5 i2c: omap: simplify IRQ exit path
instead of having multiple return points, use
a goto statement to make that clearer.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:03:26 +02:00
Felipe Balbi
6a85ced2cf i2c: omap: always return IRQ_HANDLED
Always return IRQ_HANDLED otherwise we could get our IRQ line disabled due
to many spurious IRQs.

Signed-off-by: Felipe Balbi <balbi@ti.com>
[Trivial changes to commitlogs]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:03:19 +02:00
Felipe Balbi
3ff4443f88 i2c: omap: simplify errata check
omap_i2c_dev is allocated with kzalloc(),
so we need not initialize b_hw to zero.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:03:12 +02:00
Felipe Balbi
079d8af24b i2c: omap: bus: add a receiver flag
that way we can ignore TX IRQs while in receiver
mode and ignore RX IRQs while in transmitter mode.

Signed-off-by: Felipe Balbi <balbi@ti.com>
[Remove unnecessary braces]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:03:05 +02:00
Felipe Balbi
ac79e4b249 i2c: omap: switch to platform_get_irq()
that's a nice helper from drivers core which
will give us the exact IRQ number, instead
of a pointer to an IRQ resource.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:02:57 +02:00
Felipe Balbi
1d7afc9594 i2c: omap: ack IRQ in parts
According to flow diagrams on OMAP TRMs,
we should ACK the IRQ as they happen.

Signed-off-by: Felipe Balbi <balbi@ti.com>
[Ack the stat OMAP_I2C_STAT_AL in case of arbitration lost]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:02:50 +02:00
Felipe Balbi
66b9298878 i2c: omap: switch over to do {} while loop
this will make sure that we execute at least once.
No functional changes otherwise.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:02:43 +02:00
Felipe Balbi
3312d25e1a i2c: omap: re-factor receive/transmit data loop
re-factor the common parts to a separate function,
so that code is easier to read and understand.

No functional changes.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:02:36 +02:00
Felipe Balbi
4151e74177 i2c: omap: improve i462 errata handling
Make it not depend on ISR's local variables
in order to make it easier to re-factor the
transmit data loop.
Also since we are waiting for XUDF(Transmitter underflow) just before
writing data lets not flag the underflow.
This is anyways going to go once we write
the data.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:02:28 +02:00
Felipe Balbi
6d9939f651 i2c: omap: split out [XR]DR and [XR]RDY
While they do pretty much the same thing, there
are a few peculiarities. Specially WRT erratas,
it's best to split those out and re-factor the
read/write loop to another function which both
cases call.

This last part will be done on another patch.

While at that, also avoid an unncessary register
read since dev->fifo_len will always contain the
correct amount of data to be transferred.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:02:21 +02:00
Felipe Balbi
540a4790f7 i2c: omap: simplify omap_i2c_ack_stat()
stat & BIT(1) is the same as BIT(1), so let's
simplify things a bit by removing "stat &" from
all omap_i2c_ack_stat() calls.

Code snippet (extremely simplified):

if (stat & NACK) {
        ...
        omap_i2c_ack_stat(dev, stat & NACK);
}

if (stat & RDR) {
        ...
        omap_i2c_ack_stat(dev, stat & RDR);
}

and so on. The tricky place is only WRT errata handling, for example:

if (*stat & (NACK | AL)) {
        omap_i2c_ack_stat(dev, *stat & (XRDY | XDR));
        ...
}

but in this case, the errata says we must clear XRDY and XDR if that
errata triggers, so if they just got enabled or not, it doesn't matter.

Another tricky place is RDR | RRDY (likewise for XDR | XRDY):

if (stat & (RDR | RRDY)) {
        ...
        omap_i2c_ack_stat(dev, stat & (RDR | RRDY));
}

again here there will be no issues because those IRQs never fire
simultaneously and one will only after after we have handled the
previous, that's because the same FIFO is used anyway and we won't shift
data into FIFO until we tell the IP "hey, I'm done with the FIFO, you
can shift more data"

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
[Added the explaination from the discurssion to the commit logs]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:02:14 +02:00
Felipe Balbi
c55edb9902 i2c: omap: add blank lines
trivial patch to aid readability. No functional
changes.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:02:06 +02:00
Felipe Balbi
2049b5bcdd i2c: omap: decrease indentation level on data handling
The patch intends to decrease the indentation level on the
data handling
by using the fact that else of if (dev->buf_len) is same as
if (!dev->buf_len)

if (dev->buf_len) {
	aaa;
} else {
	bbb;
	break;
}

to

if (!dev->buf_len) {
        bbb;
        break;
}
aaa;

Hence no functional changes.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:01:59 +02:00
Felipe Balbi
baf3d7b721 i2c: omap: simplify num_bytes handling
trivial patch, no functional changes

If the fifo is disabled or fifo_size is 0 the num_bytes
is set to 1. Else it is set to fifo_size or in case of a
draining interrupt the remaining bytes in the buff stat.
So the zero check is redundant and can be safely optimised.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:01:52 +02:00
Felipe Balbi
d9ebd04d34 i2c: omap: switch to devm_* API
that helps deleting some boiler plate code
and lets driver-core manage our resources
for us.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 15:01:45 +02:00
Ludovic Desroches
70d46a241e i2c: at91: add dt support to i2c-at91
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nikolaus Voss <n.voss@weinmann.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 14:49:15 +02:00
Nikolaus Voss
fac368a040 i2c: at91: add new driver
This driver has the following properties compared to the old driver:
1. Support for multiple interfaces.
2. Interrupt driven I/O as opposed to polling/busy waiting.
3. Support for _one_ repeated start (Sr) condition, which is enough
   for most real-world applications including all SMBus transfer types.
   (The hardware does not support issuing arbitrary Sr conditions on the
    bus.)

testing: SoC: at91sam9g45
	 - BQ20Z80 battery SMBus client.
	 - on a 2.6.38 kernel with several i2c clients (temp-sensor,
	   audio-codec, touchscreen-controller, w1-bridge, io-expanders)

Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Hubert Feurstein <h.feurstein@gmail.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>

[wsa: squashed with the following patches from Ludovic to have some flaws
fixed:
        i2c: at91: use managed resources
        i2c: at91: add warning about transmission issues for some devices
        i2c: at91: use an id table for SoC dependent parameters
]

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 14:49:13 +02:00
Nikolaus Voss
a879e9c34b i2c: at91: remove old polling driver
It will get replaced by a superior one. Safe to remove since this one
depends on BROKEN anyhow.

Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>

[wsa: added commit message]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 14:49:12 +02:00
Linus Walleij
e89cec7ff8 i2c: nomadik: stop fetching the regulator
The regulator fetched by the Nomadik I2C driver is actually a
voltage domain regulator. Stop doing this in the driver and
let the power domain code handle any regulators, as discussed
on the list.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 12:38:10 +02:00
Heiko Schocher
5c3d8a46ac i2c: davinci: add OF support
add of support for the davinci i2c driver.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

[wsa: fix indentation in the binding description]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-12 11:37:24 +02:00
Fabio Estevam
002f002d95 i2c: imx: Use dev_dbg logging style
Use dev_dbg logging style as it is done in other parts of this driver.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-11 23:40:53 +02:00
Fabio Estevam
06d141e9b6 i2c: imx: Use dev_info to indicate that i2c driver was succesfully registered
It is useful information in dmesg to have a message indicating that the i2c
driver was succesfully registered, so promote it to dev_info.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-09-11 23:40:53 +02:00
Arnd Bergmann
1d10a65fde i2c/mpc: make data used as *of_device_id.data const
Since of_device_id.data is declared as a pointer to const data a few
more consts can be added in this driver.

[ukl: split Arnd's patch by driver]

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2012-09-11 08:57:37 +02:00
Uwe Kleine-König
215e691c2a i2c/mpc: add a const qualifier
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:

	drivers/i2c/busses/i2c-mpc.c: In function 'fsl_i2c_probe':
	drivers/i2c/busses/i2c-mpc.c:650:31: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]

Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2012-09-11 08:56:48 +02:00
Uwe Kleine-König
c4dba0119b i2c/i2c-omap: add a const qualifier
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:

	drivers/i2c/busses/i2c-omap.c: In function 'omap_i2c_probe':
	drivers/i2c/busses/i2c-omap.c:1025: warning: assignment discards qualifiers from pointer target type

Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2012-09-11 08:56:47 +02:00
Jean Delvare
390946b172 i2c-core: Fix for lockdep validator
If kernel is compiled with CONFIG_PROVE_LOCKING the
validator raises an error when a multiplexer is removed
via sysfs and sub-clients are connected to it. This is a
false positive.
Documentation/lockdep-design.txt recommends to handle this
via calls to mutex_lock_nested().

Based on an earlier fix from Michael Lawnick.

Note that the extra code resolves to nothing unless
CONFIG_DEBUG_LOCK_ALLOC=y.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
2012-09-10 10:14:02 +02:00
Axel Lin
e68bb91baa i2c-designware: Fix build error if CONFIG_I2C_DESIGNWARE_PLATFORM=y && CONFIG_I2C_DESIGNWARE_PCI=y
This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.

Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.

This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:

  LD      drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org [3.2+]
2012-09-10 10:14:02 +02:00
James Ralston
4a8f1ddde9 i2c-i801: Add Device IDs for Intel Lynx Point-LP PCH
Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.

Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-09-10 10:14:02 +02:00
Olof Johansson
7ad8f8f1c5 Merge branch 'pnx4008-removal' of git://git.antcom.de/linux-2.6 into next/cleanup
Removes the pnx4008 platform support, which hasn't seen any active
development since 2006 and seems to be unused these days.

* 'pnx4008-removal' of git://git.antcom.de/linux-2.6:
  ARM: mach-pnx4008: Remove architecture
2012-09-05 16:16:32 -07:00
Arnd Bergmann
863e99a8c1 Merge commit 'a849088aa1' from rmk/fixes into cleanup/io-pci
As Stephen Rothwell reports, a849088aa1 ("ARM: Fix ioremap() of
address zero") from the arm-current tree and commit c279443709 ("ARM:
Add fixed PCI i/o mapping") from the arm-soc tree conflict in
a nontrivial way in arch/arm/mm/mmu.c.

Rob Herring explains:
The PCI i/o reserved area has a dummy physical address of 0 and
needs to be skipped by ioremap searches. So we don't set
VM_ARM_STATIC_MAPPING to prevent matches by ioremap. The vm_struct
settings don't really matter when we do the real mapping of the
i/o space.

Since commit a849088aa1 is at the start of the fixes branch
in the arm tree, we can merge it into the branch that contains
the other ioremap changes.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
2012-09-04 15:01:37 +02:00
Roland Stigge
d684f05f2d ARM: mach-pnx4008: Remove architecture
This patch removes the ARM architecture mach-pnx4008. No direct support or user
feedback since 2006. Acknowledgements from NXP/Philips and Linux arm-soc
maintainers.

Signed-off-by: Roland Stigge <stigge@antcom.de>
2012-08-26 16:30:37 +02:00
Laxman Dewangan
371e67c9e1 i2c: tegra: protect suspend/resume callbacks with CONFIG_PM_SLEEP
The CONFIG_PM doesn't actually enable any of the PM callbacks, it
only allows to enable CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME.
This means if CONFIG_PM is used to protect system sleep callbacks
then it may end up unreferenced if only runtime PM is enabled.
Hence protecting sleep callbacks with CONFIG_PM_SLEEP.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-08-18 20:45:09 +02:00
Guenter Roeck
ab5625c30a i2c: diolan-u2c: Fix master_xfer return code
The master_xfer function returns 0 on success. It should return the number of
successful transactions.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-08-18 12:27:27 +02:00
Kevin Hilman
33ec5e818b I2C: OMAP: xfer: fix runtime PM get/put balance on error
In omap_i2c_xfer(), ensure pm_runtime_put() is called, even on
failure.

Without this, after a failed xfer, the runtime PM usecount will have
been incremented, but not decremented causing the usecount to never
reach zero after a failure.  This keeps the device always runtime PM
enabled which keeps the enclosing power domain active, and prevents
full-chip retention/off from happening during idle.

Signed-off-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-08-18 10:11:44 +02:00
Lee Jones
b007a3ef95 i2c: nomadik: Add default configuration into the Nomadik I2C driver
At this moment in time there is only one known configuration for the
Nomadik I2C driver. By not holding that configuration in the driver
adds some unnecessary overhead in platform code. The configuration
has already been removed from platform code, this patch checks for any
over-riding configurations. If there aren't any, the default is used.

[LinusW says: "Right now this is causing boot regressions so we need it
badly..."]

Acked-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-08-18 09:56:56 +02:00
Linus Torvalds
3e9a97082f This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.  The goal is to
 addresses weaknesses discussed in the paper "Mining your Ps and Qs:
 Detection of Widespread Weak Keys in Network Devices", by Nadia
 Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
 be published in the Proceedings of the 21st Usenix Security Symposium,
 August 2012.  (See https://factorable.net for more information and an
 extended version of the paper.)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABCAAGBQJQF/0DAAoJENNvdpvBGATwIowQAOep9QKtLrBvb2lwIRVmeiy8
 lRf7V/tYZnz4FePbR0W92JQfKYkCV8yyOO0bmeRzWL3v4m+lRwDTSyA1DDyQMoH+
 LOMzvDKSLJMSXTXdSOIr1WYACphViCR/9CrbMBCKSkYfZLJ1MdaEDxT3rcpTGD0T
 6iknUweiSkHHhkerU5yQL7FKzD5kYUe0hsF47w7QVlHRHJsW2fsZqkFoh+RpnhNw
 03u+djxNGBo9qV81vZ9D1b0vA9uRlEjoWOOEG2XE4M2iq6TUySueA72dQnCwunfi
 3kG/u1Swv2dgq6aRrP3H7zdwhYSourGxziu3jNhEKwKEohrxYY7xjNX3RVeTqP67
 AzlKsOTWpRLIDrzjSLlb8VxRQiZewu8Unex3e1G+eo20sbcIObHGrxNp7K00zZvd
 QZiMHhOwItwFTe4lBO+XbqH2JKbL9/uJmwh5EipMpQTraKO9E6N3CJiUHjzBLo2K
 iGDZxRMKf4gVJRwDxbbP6D70JPVu8ZJ09XVIpsXQ3Z1xNqaMF0QdCmP3ty56q1o0
 NvkSXxPKrijZs8Sk0rVDqnJ3ll8PuDnXMv5eDtL42VT818I5WxESn9djjwEanGv0
 TYxbFub/NRxmPEE5B2Js5FBpqsLf5f282OSMeS/5WLBbnHJR1OoPoAhGVpHvxntC
 bi5FC1OolqhvzVIdsqgt
 =u7KM
 -----END PGP SIGNATURE-----

Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random

Pull random subsystem patches from Ted Ts'o:
 "This patch series contains a major revamp of how we collect entropy
  from interrupts for /dev/random and /dev/urandom.

  The goal is to addresses weaknesses discussed in the paper "Mining
  your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
  by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J.  Alex Halderman,
  which will be published in the Proceedings of the 21st Usenix Security
  Symposium, August 2012.  (See https://factorable.net for more
  information and an extended version of the paper.)"

Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
  random: mix in architectural randomness in extract_buf()
  dmi: Feed DMI table to /dev/random driver
  random: Add comment to random_initialize()
  random: final removal of IRQF_SAMPLE_RANDOM
  um: remove IRQF_SAMPLE_RANDOM which is now a no-op
  sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
  [ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
  board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
  isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
  pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
  omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
  goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
  uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
  drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
  xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
  n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
  pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
  i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
  input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
  mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
  ...
2012-07-31 19:07:42 -07:00
Linus Torvalds
6df419e45d Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
 "This is the first part of the media patches for v3.6.

  This patch series contain:
   - new DVB frontend: rtl2832
   - new video drivers: adv7393
   - some unused files got removed
   - a selection API cleanup between V4L2 and V4L2 subdev API's
   - a major redesign at v4l-ioctl2, in order to clean it up
   - several driver fixes and improvements."

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (174 commits)
  v4l: Export v4l2-common.h in include/linux/Kbuild
  media: Revert "[media] Terratec Cinergy S2 USB HD Rev.2"
  [media] media: Use pr_info not homegrown pr_reg macro
  [media] Terratec Cinergy S2 USB HD Rev.2
  [media] v4l: Correct conflicting V4L2 subdev selection API documentation
  [media] Feature removal: V4L2 selections API target and flag definitions
  [media] v4l: Unify selection flags documentation
  [media] v4l: Unify selection flags
  [media] v4l: Common documentation for selection targets
  [media] v4l: Unify selection targets across V4L2 and V4L2 subdev interfaces
  [media] v4l: Remove "_ACTUAL" from subdev selection API target definition names
  [media] V4L: Remove "_ACTIVE" from the selection target name definitions
  [media] media: dvb-usb: print mac address via native %pM
  [media] s5p-tv: Use module_i2c_driver in sii9234_drv.c file
  [media] media: gpio-ir-recv: add allowed_protos for platform data
  [media] s5p-jpeg: Use module_platform_driver in jpeg-core.c file
  [media] saa7134: fix spelling of detach in label
  [media] cx88-blackbird: replace ioctl by unlocked_ioctl
  [media] cx88: don't use current_norm
  [media] cx88: fix a number of v4l2-compliance violations
  ...
2012-07-30 19:03:41 -07:00
Linus Torvalds
27c1ee3f92 Merge branch 'akpm' (Andrew's patch-bomb)
Merge Andrew's first set of patches:
 "Non-MM patches:

   - lots of misc bits

   - tree-wide have_clk() cleanups

   - quite a lot of printk tweaks.  I draw your attention to "printk:
     convert the format for KERN_<LEVEL> to a 2 byte pattern" which
     looks a bit scary.  But afaict it's solid.

   - backlight updates

   - lib/ feature work (notably the addition and use of memweight())

   - checkpatch updates

   - rtc updates

   - nilfs updates

   - fatfs updates (partial, still waiting for acks)

   - kdump, proc, fork, IPC, sysctl, taskstats, pps, etc

   - new fault-injection feature work"

* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
  drivers/misc/lkdtm.c: fix missing allocation failure check
  lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
  fault-injection: add tool to run command with failslab or fail_page_alloc
  fault-injection: add selftests for cpu and memory hotplug
  powerpc: pSeries reconfig notifier error injection module
  memory: memory notifier error injection module
  PM: PM notifier error injection module
  cpu: rewrite cpu-notifier-error-inject module
  fault-injection: notifier error injection
  c/r: fcntl: add F_GETOWNER_UIDS option
  resource: make sure requested range is included in the root range
  include/linux/aio.h: cpp->C conversions
  fs: cachefiles: add support for large files in filesystem caching
  pps: return PTR_ERR on error in device_create
  taskstats: check nla_reserve() return
  sysctl: suppress kmemleak messages
  ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
  ipc: compat: use signed size_t types for msgsnd and msgrcv
  ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
  ipc: add COMPAT_SHMLBA support
  ...
2012-07-30 17:25:34 -07:00
Viresh Kumar
dd995c9d82 i2c/i2c-pxa: remove conditional compilation of clk code
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.

pxa i2c also has these dummy macros defined locally.  Remove them as they
aren't required anymore.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-07-30 17:25:12 -07:00
Linus Torvalds
287dc4b764 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "More hardware support across the field including a bunch of device
  drivers.  The highlight however really are further steps towards
  device tree.

  This has been sitting in -next for ages.  All MIPS _defconfigs have
  been tested to boot or where I don't have hardware available, to at
  least build fine."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
  MIPS: Loongson 1B: Add defconfig
  MIPS: Loongson 1B: Add board support
  MIPS: Netlogic: early console fix
  MIPS: Netlogic: Fix indentation of smpboot.S
  MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
  MIPS: Netlogic: Remove unused pcibios_fixups
  MIPS: Netlogic: Add XLP SoC devices in FDT
  MIPS: Netlogic: Add IRQ mappings for more devices
  MIPS: Netlogic: USB support for XLP
  MIPS: Netlogic: XLP PCIe controller support.
  MIPS: Netlogic: Platform changes for XLR/XLS I2C
  MIPS: Netlogic: Platform NAND/NOR flash support
  MIPS: Netlogic: Platform changes for XLS USB
  MIPS: Netlogic: Remove NETLOGIC_ prefix
  MIPS: Netlogic: SMP wakeup code update
  MIPS: Netlogic: Update comments in smpboot.S
  MIPS: BCM63XX: Add 96328avng reference board
  MIPS: Expose PCIe drivers for MIPS
  MIPS: BCM63XX: Add PCIe Support for BCM6328
  MIPS: BCM63XX: Move the PCI initialization into its own function
  ...
2012-07-30 11:45:52 -07:00
Linus Torvalds
a410963ba4 Merge branch 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux
Pull embedded i2c changes from Wolfram Sang:
 "Changes for the "embedded" part of the I2C subsystem:

   - lots of devicetree conversions of drivers (and preparations for
     that)
   - big cleanups for drivers for OMAP, Tegra, Nomadik, Blackfin
   - Rafael's struct dev_pm_ops conversion patches for I2C
   - usual driver cleanups and fixes

  All patches have been in linux-next for an apropriate time and all
  patches touching files outside of i2c-folders should have proper acks
  from the maintainers."

* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (60 commits)
  Revert "i2c: tegra: convert normal suspend/resume to *_noirq"
  I2C: MV64XYZ: Add Device Tree support
  i2c: stu300: use devm managed resources
  i2c: i2c-ocores: support for 16bit and 32bit IO
  V4L/DVB: mfd: use reg_shift instead of regstep
  i2c: i2c-ocores: Use reg-shift property
  i2c: i2c-ocores: DT bindings and minor fixes.
  i2c: mv64xxxx: remove EXPERIMENTAL tag
  i2c-s3c2410: Use plain pm_runtime_put()
  i2c: s3c2410: Fix pointer type passed to of_match_node()
  i2c: mxs: Set I2C timing registers for mxs-i2c
  i2c: i2c-bfin-twi: Move blackfin TWI register access Macro to head file.
  i2c: i2c-bfin-twi: Move TWI peripheral pin request array to platform data.
  i2c:i2c-bfin-twi: include twi head file
  i2c:i2c-bfin-twi: TWI fails to restart next transfer in high system load.
  i2c: i2c-bfin-twi: Tighten condition when failing I2C transfer if MEN bit is reset unexpectedly.
  i2c: i2c-bfin-twi: Break dead waiting loop if i2c device misbehaves.
  i2c: i2c-bfin-twi: Improve the patch for bug "Illegal i2c bus lock upon certain transfer scenarios".
  i2c: i2c-bfin-twi: Illegal i2c bus lock upon certain transfer scenarios.
  i2c-mv64xxxx: allow more than one driver instance
  ...

Conflicts:
	drivers/i2c/busses/i2c-nomadik.c
2012-07-28 13:43:12 -07:00
Rob Herring
701eb2647d i2c: iop3xx: use standard gpiolib functions
Instead of using the custom iop3xx gpio functions, use the gpiolib
variants. This should be functionally the same since the gpiolib
just calls the iop3xx gpio functions. This is needed in preparation
of removing iop3xx mach/io.h headers.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: "Jean Delvare (PC drivers, core)" <khali@linux-fr.org>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
2012-07-25 09:26:41 -05:00
Rob Herring
67ac88ff10 i2c: iop3xx: clean-up trailing whitespace
Remove a bunch of trailing whitespace. No functional changes.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: "Jean Delvare (PC drivers, core)" <khali@linux-fr.org>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
2012-07-25 09:26:40 -05:00
Wolfram Sang
5db20c49e2 Revert "i2c: tegra: convert normal suspend/resume to *_noirq"
This reverts commit 7c86d44cda.
Stephen says:

IIRC, I proposed it before solely to solve some suspend/resume ordering
issues, and Colin Cross NAKd it. These days, deferred probe should make
this change unnecessary.

Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-07-24 17:32:45 +02:00
Laurent Pinchart
fb604a3d58 i2c-omap: Add support for I2C_M_STOP message flag
Generate a stop condition after each message marked with I2C_M_STOP.

[JD: Add I2C_FUNC_PROTOCOL_MANGLING.]

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:59 +02:00
Laurent Pinchart
72fc2c7f78 i2c: Fall back to emulated SMBus if the operation isn't supported natively
Adapter drivers might support only a subset of the SMBus operations
natively. Those drivers currently have to manually emulate unsupported
operations using I2C.

Make the i2c_smbus_xfer() function fall back to
i2c_smbus_xfer_emulated() when the adapter's .smbus_xfer() operation
returns -EOPNOTSUPP, like it already does when the .smbus_xfer()
operation isn't available at all.

[JD: Minor optimization.]

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:59 +02:00
Laurent Pinchart
d47726c521 i2c: Add SCCB support
SCCB is a serial communication bus developed by Omnivision. Its 2-wire
mode is very similar to SMBus byte data transactions, but requires the
controller to ignore the ACK bit and to insert a stop condition after
each message.

Add a device SCCB flag and a message stop flag to be passed to
controller drivers.

[JD: Kill rogue definition in go7007 driver.]

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:59 +02:00
Emmanuel Deloget
68a7602f09 i2c-tiny-usb: Add support for the Robofuzz OSIF USB/I2C converter
Robofuzz OSIF is a generic USB/iIC interface that embeds an ATMega8A
AVR-RISC microcontroler.

The device is based upon Till Harbaum's i2c-tiny-usb and although it
enhances the original design with further functionnalities it still
maintain compatibility with it with respect to the USB/I2C interface.

Signed-off-by: Emmanuel Deloget <logout@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:59 +02:00
Daniel Kurtz
d3ff6ce400 i2c-i801: Enable IRQ for byte_by_byte transactions
Byte-by-byte transactions are used primarily for accessing I2C devices
with an SMBus controller.  For these transactions, for each byte that is
read or written, the SMBus controller generates a BYTE_DONE IRQ.  The isr
reads/writes the next byte, and clears the IRQ flag to start the next byte.
On the penultimate IRQ, the isr also sets the LAST_BYTE flag.

There is no locking around the cmd/len/count/data variables, since the
I2C adapter lock ensures there is never multiple simultaneous transactions
for the same device, and the driver thread never accesses these variables
while interrupts might be occurring.

The end result is faster I2C block read and write transactions.

Note: This patch has only been tested and verified by doing I2C read and
write block transfers on Cougar Point 6 Series PCH, as well as I2C read
block transfers on ICH5.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:59 +02:00
Jean Delvare
29b608540b i2c-i801: Enable interrupts on ICH5/7/8/9/10
Enable interrupts on more devices. ICH5, ICH7(-M) and ICH10 have been
tested to work OK. ICH8 and ICH9 are expected to work just fine as
they are very close to ICH7 and ICH10.

Ultimately we want to enable this feature on at least every device
since the ICH5, but for now we limit the exposure. We'll enable it for
other devices if we don't get negative feedback.

As a bonus, let the user know when interrupts are used.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Daniel Kurtz <djkurtz@chromium.org>
2012-07-24 14:13:59 +02:00
Daniel Kurtz
636752bcb5 i2c-i801: Enable IRQ for SMBus transactions
Add a new 'feature' to i2c-i801 to enable using PCI interrupts.
When the feature is enabled, then an isr is installed for the device's
PCI IRQ.

An I2C/SMBus transaction is always terminated by one of the following
interrupt sources: FAILED, BUS_ERR, DEV_ERR, or on success: INTR.

When the isr fires for one of these cases, it sets the ->status variable
and wakes up the waitq.  The waitq then saves off the status code, and
clears ->status (in preparation for some future transaction).
The SMBus controller generates an INTR irq at the end of each
transaction where INTREN was set in the HST_CNT register.

No locking is needed around accesses to priv->status since all writes to
it are serialized: it is only ever set once in the isr at the end of a
transaction, and cleared while no interrupts can occur.  In addition, the
I2C adapter lock guarantees that entire I2C transactions for a single
adapter are always serialized.

For this patch, the INTREN bit is set only for SMBus block, byte and word
transactions, but not for I2C reads or writes.  The use of the DS
(BYTE_DONE) interrupt with byte-by-byte I2C transactions is implemented in
a subsequent patch.

The interrupt feature has only been enabled for COUGARPOINT hardware.
In addition, it is disabled if SMBus is using the SMI# interrupt.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:58 +02:00
Jean Delvare
6cad93c4bb i2c-i801: Consolidate polling
(Based on earlier work by Daniel Kurtz.)

Come up with a consistent, driver-wide strategy for event polling. For
intermediate steps of byte-by-byte block transactions, check for
BYTE_DONE or any error flag being set. At the end of every transaction
(regardless of PEC being used), check for both BUSY being cleared and
INTR or any error flag being set. This ensures proper action for all
transaction types.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Daniel Kurtz <djkurtz@chromium.org>
2012-07-24 14:13:58 +02:00
Daniel Kurtz
37af871112 i2c-i801: Drop ENABLE_INT9
Later patches enable interrupts.  This preliminary patch removes the older
unsupported ENABLE_INT9 flag.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:58 +02:00
Daniel Kurtz
edbeea6383 i2c-i801: Rename some SMBHSTCNT bit constants
Rename the SMBHSTCNT register bit access constants to match the style of
other register bits.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:58 +02:00
Daniel Kurtz
70a1cc1952 i2c-i801: Check and return errors during byte-by-byte transfers
If an error is detected in the polling loop, abort the transaction and
return an error code.

 * DEV_ERR is set if the device does not respond with an acknowledge, and
the SMBus controller times out (minimum 25ms).
 * BUS_ERR is set if a bus arbitration collision is detected.  In other
words, when the SMBus controller tries to generate a START condition, but
detects that the SMBDATA is being held low, usually by another SMBus/I2C
master.
 * FAILED is only set if a transaction is stopped by software (using
the SMBHSTCNT KILL bit).

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:58 +02:00