Commit graph

364 commits

Author SHA1 Message Date
David Brownell
529ba0d966 spi: bitbang bugfix in message setup
Bugfix to spi_bitbang infrastructure: make sure to always set transfer
parameters on the first pass through the message's per-transfer loop.
This can matter with drivers that replace the per-word or per-buffer
transfer primitives, on busses with multiple SPI devices.

Previously, this could have started messages using the settings left after
previous messages.  The problem was observed when a high speed chip
(m25p80 type flash) was running very slowly because a low speed device
(avr8 microcontroller) had previously used the bus.  Similar faults could
have driven the low speed device too fast, or used an unexpected word
size.

Acked-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
David Brownell
70d6027ff2 spi: add spi_master flag word
Add a new spi_master.flags word listing constraints relevant to that
controller.  Define the first constraint bit: a half duplex restriction.
Include that constraint in the OMAP1 MicroWire controller driver.

Have the mmc_spi host be the first customer of this flag.  Its coding
relies heavily on full duplex transfers, so it must fail when the
underlying controller driver won't perform them.

(The spi_write_then_read routine could use it too: use the
temporarily-withdrawn full-duplex speedup unless this flag is set, in
which case the existing code applies.  Similarly, any spi_master
implementing only SPI_3WIRE should set the flag.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
David Brownell
b55f627fee spi: new spi->mode bits
Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:

 * SPI_NO_CS ... a second 3-wire variant, where the chipselect
   line is removed instead of a data line; transfers are still
   full duplex.

   This obviously has STRONG protocol implications since the
   chipselect transitions can't be used to synchronize state
   transitions with the SPI master.

 * SPI_READY ... defines open drain signal that's pulled low
   to pause the clock.  This defines a 5-wire variant (normal
   4-wire SPI plus READY) and two 4-wire variants (READY plus
   each of the 3-wire flavors).

   Such hardware flow control can be a big win.  There are ADC
   converters and flash chips that expose READY signals, but not
   many host controllers support it today.

The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack.  That's a mode most hardware can easily support
(unlike SPI_READY).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Paulraj, Sandeep" <s-paulraj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-30 18:56:00 -07:00
Anton Vorontsov
575c5807f6 spi_mpc8xxx: s/83xx/8xxx/g
Since we renamed the file, we might want to rename the file internals too.

Though we don't bother with changing platform driver name and platform
module alias.  The stuff is legacy and hopefully we'll remove it soon.

Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 16:46:05 -07:00
Anton Vorontsov
34a661a1fe spi_mpc83xx: rename spi_83xx.c to spi_8xxx.c
The driver handles MPC83xx, MPC85xx and MPC86xx SPI controllers, so rename
the file for clarity.

Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 16:46:05 -07:00
Anton Vorontsov
aef79d8276 spi_mpc83xx: remove dead code
This patch removes #if 0'ed code, and spi_mpc83xx->busy variable that is
used by that dead snippet only.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 16:46:05 -07:00
Anton Vorontsov
b9b9af11fe spi_mpc83xx: split mpc83xx_spi_work() into two routines
mpc83xx_spi_work() is quite large, with up to five indentation levels and
is quite difficult to read.

So, split the function in two parts:
1. mpc83xx_spi_work() now only traverse queued spi messages;
2. mpc83xx_spi_do_one_msg() only manages single messages.

There should be no functional changes.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 16:46:05 -07:00
Anton Vorontsov
9effb959de spi_mpc83xx: fix checkpatch issues
Checkpatch is spitting errors when seeing the rename patch, so fix the
errors prior to moving.

Following errors and warnings were fixed:

   WARNING: Use #include <linux/io.h> instead of <asm/io.h>
   #1027: FILE: drivers/spi/spi_mpc8xxx.c:37:
   +#include <asm/io.h>

   ERROR: "foo * bar" should be "foo *bar"
   #1111: FILE: drivers/spi/spi_mpc8xxx.c:121:
   +static inline void mpc83xx_spi_write_reg(__be32 __iomem * reg, u32 val)

   ERROR: "foo * bar" should be "foo *bar"
   #1116: FILE: drivers/spi/spi_mpc8xxx.c:126:
   +static inline u32 mpc83xx_spi_read_reg(__be32 __iomem * reg)

   ERROR: "foo * bar" should be "foo *bar"
   #1125: FILE: drivers/spi/spi_mpc8xxx.c:135:
   +       type * rx = mpc83xx_spi->rx;                                      \

   ERROR: "foo * bar" should be "foo *bar"
   #1135: FILE: drivers/spi/spi_mpc8xxx.c:145:
   +       const type * tx = mpc83xx_spi->tx;                      \

   WARNING: suspect code indent for conditional statements (16, 25)
   #1504: FILE: drivers/spi/spi_mpc8xxx.c:514:
   +               while (((event =
   [...]
   +                        cpu_relax();

Following warnings were left over, since fixing them will hurt the
readability.  We'd better fix them by lowering the indentation level by
splitting mpc83xx_spi_work function into two parts.

   WARNING: line over 80 characters
   #1371: FILE: drivers/spi/spi_mpc8xxx.c:381:
   +                                       status = mpc83xx_spi_setup_transfer(spi, t);

   WARNING: line over 80 characters
   #1392: FILE: drivers/spi/spi_mpc8xxx.c:402:
   +                               mpc83xx_spi_chipselect(spi, BITBANG_CS_INACTIVE);

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 16:46:04 -07:00
Anton Vorontsov
5afbf098d1 spi_mpc83xx: add small delay after asserting chip-select line
This is needed for some underlaying GPIO controllers that may be a bit
slow, or if chip-select signal need some time to stabilize.

For what it's worth, we already have the similar delay for chip-select
de-assertion case.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 16:46:04 -07:00
Anton Vorontsov
fd8a11e100 spi_mpc83xx: quieten down the "Requested speed is too low" message
When a platform is running at high frequencies it's not always possible to
scale-down a frequency to a requested value, and using mmc_spi driver this
leads to the following printk flood during card polling:

  ...
  mmc_spi spi32766.0: Requested speed is too low: 400000 Hz. Will use
  520828 Hz instead.
  mmc_spi spi32766.0: Requested speed is too low: 400000 Hz. Will use
  520828 Hz instead.
  ...

Fix this by using WARN_ONCE(), it's better than the flood, and also better
than turning dev_err() into dev_dbg(), since we actually want to warn that
some things may not work correctly.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 16:46:04 -07:00
Anton Vorontsov
9e04b3336a spi_mpc83xx: handle other Freescale processors
With this patch we'll able to select spi_mpc83xx driver on the MPC86xx
platforms.  Let the driver depend on FSL_SOC, so we don't have to worry
about Kconfig anymore.

Also remove the "experimental" dependency, the driver has been tested to
work on a various hardware, and surely not experimental anymore.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-19 16:46:04 -07:00
Jiri Pirko
275704970c spi: fix spi_write_then_read() comment
Buffer needs not be dma-safe, not rx data length.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-18 13:03:42 -07:00
Daniel Ribeiro
50e0a7bd02 pxa2xx_spi: fix for SPI_CS_HIGH
Commit a7bb3909b3 ("spi: pxa2xx_spi:
introduce chipselect GPIO to simplify the common cases") introduces
chipselect GPIO, and configures the CS polarity using SPI_CS_HIGH
spi->mode flag.  Add SPI_CS_HIGH to the allowed modes.

Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-18 13:03:42 -07:00
Anton Vorontsov
7390284290 mpc52xx_psc_spi: convert to cs_control callback
mpc52xx_psc_spi driver is the last user of the legacy activate_cs and
deactivate_cs callbacks, so convert the driver to the cs_control hook and
remove the legacy callbacks from fsl_spi_platform_data struct.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-18 13:03:42 -07:00
David Brownell
e7db06b5d5 spi: move more spi_setup() functionality into core
Move some common spi_setup() error checks into the SPI framework from the
spi_master controller drivers:

 - Add a new "mode_bits" field to spi_master

 - Use that in spi_setup to validate the spi->mode value being
   requested.  Setting this new field is now mandatory for any
   controller supporting more than vanilla SPI_MODE_0.

 - Update all spi_master drivers to:

     * Initialize that field
     * Remove current spi_setup() checks using that value.

This is a net minor code shrink.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-18 13:03:42 -07:00
David Brownell
7d0771970c spi: move common spi_setup() functionality into core
Start moving some spi_setup() functionality into the SPI core from the
various spi_master controller drivers:

 - Make that function stop being an inline;

 - Move two common idioms from drivers into that new function:
    * Default bits_per_word to 8 if that field isn't set
    * Issue a standardized dev_dbg() message

This is a net minor source code shrink, and supports enhancments found in
some follow-up patches.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-18 13:03:42 -07:00
Roel Kluin
b4bd2ababd spi_bfin5xx: limit reaches -1
bfin_spi_flush() returns limit, which reaches -1 upon timeout.  but in
function bfin_spi_pump_transfers() it is compared with 0.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-18 13:03:41 -07:00
Linus Torvalds
517d08699b Merge branch 'akpm'
* akpm: (182 commits)
  fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
  fbdev: *bfin*: fix __dev{init,exit} markings
  fbdev: *bfin*: drop unnecessary calls to memset
  fbdev: bfin-t350mcqb-fb: drop unused local variables
  fbdev: blackfin has __raw I/O accessors, so use them in fb.h
  fbdev: s1d13xxxfb: add accelerated bitblt functions
  tcx: use standard fields for framebuffer physical address and length
  fbdev: add support for handoff from firmware to hw framebuffers
  intelfb: fix a bug when changing video timing
  fbdev: use framebuffer_release() for freeing fb_info structures
  radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
  s3c-fb: CPUFREQ frequency scaling support
  s3c-fb: fix resource releasing on error during probing
  carminefb: fix possible access beyond end of carmine_modedb[]
  acornfb: remove fb_mmap function
  mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
  mb862xxfb: restrict compliation of platform driver to PPC
  Samsung SoC Framebuffer driver: add Alpha Channel support
  atmel-lcdc: fix pixclock upper bound detection
  offb: use framebuffer_alloc() to allocate fb_info struct
  ...

Manually fix up conflicts due to kmemcheck in mm/slab.c
2009-06-16 19:50:13 -07:00
Roel Kluin
021415468c spi: takes size of a pointer to determine the size of the pointed-to type
Do not take the size of a pointer to determine the size of the pointed-to
type.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-16 19:47:27 -07:00
Linus Torvalds
8d6cea5111 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (27 commits)
  Blackfin: hook up new rt_tgsigqueueinfo syscall
  Blackfin: improve CLKIN_HZ config default
  Blackfin: initial support for ftrace grapher
  Blackfin: initial support for ftrace
  Blackfin: enable support for LOCKDEP
  Blackfin: add preliminary support for STACKTRACE
  Blackfin: move custom sections into sections.h
  Blackfin: punt unused/wrong mutex-dec.h
  Blackfin: add support for irqflags
  Blackfin: add support for bzip2/lzma compressed kernel images
  Blackfin: convert Kconfig style to def_bool
  Blackfin: bf548-ezkit: update smsc911x resources
  Blackfin: update aedos-ipipe code to upstream 1.10-00
  Blackfin: bf537-stamp: update ADP5520 resources
  Blackfin: bf518f-ezbrd: fix SPI CS for SPI flash
  Blackfin: define SPI IRQ in board resources
  Blackfin: do not configure the UART early if on wrong processor
  Blackfin: fix deadlock in SMP IPI handler
  Blackfin: fix flag storage for irq funcs
  Blackfin: push down exception oops checking
  ...
2009-06-16 11:49:58 -07:00
Linus Torvalds
2cf4d4514d Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
  MAINTAINERS: EB110ATX is not ebsa110
  MAINTAINERS: update Eric Miao's email address and status
  fb: add support of LCD display controller on pxa168/910 (base layer)
  [ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
  [ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
  [ARM] 5544/1: Trust PrimeCell resource sizes
  [ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
  [ARM] pxa/sharpsl_pm: drop set_irq_type calls
  [ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
  [ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
  [ARM] sa1100: remove unused collie_pm.c
  [ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
  [ARM] 5550/1: Add default configure file for w90p910 platform
  [ARM] 5549/1: Add clock api for w90p910 platform.
  [ARM] 5548/1: Add gpio api for w90p910 platform
  [ARM] 5551/1: Add multi-function pin api for w90p910 platform.
  [ARM] Make ARM_VIC_NR depend on ARM_VIC
  [ARM] 5546/1: ARM PL022 SSP/SPI driver v3
  ARM: OMAP4: SMP: Update defconfig for OMAP4430
  ARM: OMAP4: SMP: Enable SMP support for OMAP4430
  ...
2009-06-14 13:42:43 -07:00
Jie Zhang
67834fa93d Blackfin: rename bfin_addr_dcachable to bfin_addr_dcacheable
The latter naming convention is much more common.

Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-13 07:20:06 -04:00
Russell King
547c32aeb5 Merge branch for-rmk-devel of git://aeryn.fluff.org.uk/bjdooks/linux into devel 2009-06-10 22:41:06 +01:00
Linus Walleij
b43d65f7e8 [ARM] 5546/1: ARM PL022 SSP/SPI driver v3
This adds a driver for the ARM PL022 PrimeCell SSP/SPI
driver found in the U300 platforms as well as in some
ARM reference hardware, and in a modified version on the
Nomadik board.

Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-06-10 22:39:52 +01:00
Russell King
fc05505b77 Merge branch 'ixp4xx' of git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6 into devel 2009-05-23 23:18:40 +01:00
Michal Simek
6fa612b56c microblaze: Kconfig: Enable drivers for Microblaze
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-05-21 15:56:04 +02:00
Ben Dooks
ec976d6eb0 [ARM] S3C24XX: GPIO: Move gpio functions out of <mach/hardware.h>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.

Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).

Note, this does make minor changes to some drivers but
should not mess up any pending merges.

CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-05-18 16:25:40 +01:00
Daniel Ribeiro
7348d82a67 pxa2xx_spi: prevent panic case setup() fails
setup() may fail before ctldata is set, causing a kernel panic on
cleanup().

Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-05-12 14:11:34 -07:00
Sascha Hauer
8c8fdbc9bd [ARM] Remove arch-imx from build system
arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:15:48 +02:00
Roel Kluin
306c68aaa7 spi: pxa2xx: limit reaches -1
On line 944 the return value of flush() is considered as a boolean,
but limit reaches -1 upon timeout which evaluates to true.

On 540, 594, 720 the same occurs for wait_ssp_rx_stall()
On 536 the same occurs for wait_dma_channel_stop()

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-21 13:41:49 -07:00
Daniel Ribeiro
148da33120 pxa2xx_spi: restore DRCMR on resume
If DMA is enabled, any spi_sync call after suspend/resume would block
forever, because DRCMR is lost on suspend.  This patch restores DRCMR to
the same values set by probe.

Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-21 13:41:49 -07:00
Russell King
9fa264d0d3 Merge branch 'fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 2009-04-15 09:58:21 +01:00
David Brownell
bdff549ebe spi: spi_write_then_read() bugfixes
The "simplify spi_write_then_read()" patch included two regressions from
the 2.6.27 behaviors:

 - The data it wrote out during the (full duplex) read side
   of the transfer was not zeroed.

 - It fails completely on half duplex hardware, such as
   Microwire and most "3-wire" SPI variants.

So, revert that patch.  A revised version should be submitted at some
point, which can get the speedup on standard hardware (full duplex)
without breaking on less-capable half-duplex stuff.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>		[2.6.28.x, 2.6.29.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-13 15:04:30 -07:00
Daniel Ribeiro
2b2562d381 [ARM] pxa: fix typo of cs_deassert() in pxa2xx-spi.c
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2009-04-13 12:10:36 +08:00
Mike Rapoport
96a6d9aa09 spi_imx: set spi_master.dma_alignment = 4
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:07 -07:00
Mike Rapoport
7ad0ba91d4 pxa2xx_spi: set spi_master.dma_alignment = 8
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:07 -07:00
Mike Rapoport
75c8915c0c spi_bfin5xx: remove unused IS_DMA_ALIGNED macro
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:07 -07:00
Eric Miao
a7bb3909b3 spi: pxa2xx_spi: introduce chipselect GPIO to simplify the common cases
Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs
for this.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:07 -07:00
Roel Kluin
c8fc657e6a spi: limit reaches -1, tested 0
With a postfix decrement limit will reach -1 rather than 0, so the warning
will not be issued.

Also, add a cpu_relax() into the busy-wait loop.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Mariusz Ceier <mceier@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:07 -07:00
Wolfgang Muees
93b61bddc1 Blackfin SPI Driver: Make mmc_spi driver work on Blackfin
1. Rewrite of the non-dma data transfer functions to use only ONE mode
   of TIMOD (TIMOD=0x1).  With TIMOD=0, it was not possible to set the TX
   bit pattern.  So the TDBR = 0xFFFF inside the read calls won't work.

2. Clear SPI_RDBR before reading and before duplex transfer.
   Otherwise the garbage data in RDBR will get read.  Since mmc_spi uses a
   lot of duplex transfers, this is the main cause of mmc_spi failure.

3. Poll RXS for transfer completion.  Polling SPIF or TXS cannot
   guarantee transfer completion.  This may interrupt a transfer before it
   is finished.  Also this may leave garbage data in buffer and affect
   next transfer.

[Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct
bfin5xx_spi_chip" to specify the value to transmit if no TX value
is supplied.]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:06 -07:00
Michael Hennerich
42c78b2bf5 Blackfin SPI Driver: Add GPIO controlled SPI Slave Select support
Add support for GPIO controlled SPI Chip Selects.  To make use of this
feature, set chip_select = 0 and add a proper cs_gpio to your
controller_data.

struct spi_board_info
        .chip_select = 0

struct bfin5xx_spi_chip
        .cs_gpio = GPIO_P###

There are various SPI devices that require SPI MODE_0, and need to have
the Chip Selects asserted during the entire transfer.  Consider using
SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:06 -07:00
Mike Frysinger
e7d02e3c95 Blackfin SPI Driver: fix NULL pointer crash
Fix NULL pointer crash when cleaning up from invalid platform resources

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:06 -07:00
Mike Frysinger
138f97cd06 Blackfin SPI Driver: use bfin_spi_ prefix on all functions
Do this because when things crash, we get simple names like "setup" and
"start_queue" which is pretty difficult to trace back to the real thing:
the spi driver

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:06 -07:00
Yi Li
b9b2a76a43 Blackfin SPI Driver: fix bug - correct usage of struct spi_transfer.cs_change
According to comments in linux/spi/spi.h:

 * All SPI transfers start with the relevant chipselect active.  Normally
 * it stays selected until after the last transfer in a message. Drivers
 * can affect the chipselect signal using cs_change.
 *
 * (i) If the transfer isn't the last one in the message, this flag is
 * used to make the chipselect briefly go inactive in the middle of the
 * message.  Toggling chipselect in this way may be needed to terminate
 * a chip command, letting a single spi_message perform all of group of
 * chip transactions together.
 *
 * (ii) When the transfer is the last one in the message, the chip may
 * stay selected until the next transfer.  On multi-device SPI busses
 * with nothing blocking messages going to other devices, this is just
 * a performance hint; starting a message to another device deselects
 * this one.  But in other cases, this can be used to ensure correctness.
 * Some devices need protocol transactions to be built from a series of
 * spi_message submissions, where the content of one message is determined
 * by the results of previous messages and where the whole transaction
 * ends when the chipselect goes intactive.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:06 -07:00
Yi Li
2cf3683472 Blackfin SPI Driver: fix bug - spi controller driver does not assert/deassert CS correctly
This bug can be observed when two SPI devices are sharing the spi bus: One
device is set as SPI CS 7, another one is using SPI CS 4.

In spi_bfin5xx.c: cs_active(), cs_deactive() are used to control SPI_FLG
register.  From the debug bellow:

cs_active: flag: 0x7f91, chip->flag: 0x7f80, cs: 7
cs_active: flag: 0xef91, chip->flag: 0xef10, cs: 4

When device A (cs_7) activate CS 7, SPI_FLG is set as 0x7f91 (however,
SPI_FLG should be set as 0x7f80, or 0x6f91 if in broadcast mode).

Due to some HW bug (very possibly), if SPI_FLG is set as 0x7f91, SPISSEL7
is asserted, however SPISSEL4 will be asserted too (I can see this using
the scope).  This is unreasonable according to HRM.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:06 -07:00
Mike Frysinger
a963ea83b3 Blackfin SPI Driver: tweak magic spi dma sequence to get it working on BF54x
Without this change, SPI DMA is not reliably under stress tests.
Obiviously it's a hardware issue which is not addressed by any document.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:06 -07:00
Mike Frysinger
aaaf939c57 Blackfin SPI Driver: add timeout while waiting for SPIF in dma irq handler
The "while" endless loop will cause the system hang if hardware error, so
we add timeout control to make the system alive.

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:05 -07:00
Mike Frysinger
11d6f59951 Blackfin SPI Driver: get dma working for SPI flashes
When using a BF533-STAMP here with a W25X10 SPI flash.  It works fine when
enable_dma is disabled, but doesn't work at all when turning DMA on.  We
get just 0xff bytes back when trying to read the device.

Change the code around so that it programs the SPI first and then enables
DMA, it seems to work a lot better ...

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:05 -07:00
Mike Frysinger
4160bde2d8 Blackfin SPI Driver: SPI slave select code cleanup
- remove duplicated definition MAX_SPI_SSEL

- remove unnecessary array size

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:05 -07:00
Mike Frysinger
b31e27a6dc Blackfin SPI Driver: use the properl BIT_CTL_xxx defines
use the properl BIT_CTL_...  defines rather than the internal driv er
CFG_SPI_...  defines

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:05 -07:00