The code for checksum is more complex than needed when dealing with VLAN's;
the higher layers already pass down the location of the IP header.
Compile tested only, no hardware available.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch has added return value check of request_irq() to pcmcia net drivers.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CONFIG_NETDEVICES, CONFIG_NET_ETHERNET:
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
CONFIG_SMC9194:
Move it so that it appears correctly in menuconfig.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
acenic: SET_NETDEV_DEV is always there these days
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use netdev_alloc_skb rather than dev_alloc_skb when allocating
receive buffers.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The receive buffer offset is constant in this driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to grap full size MTU buffer for possibly small transmit
bounce buffers.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the PHY and statistic timer run on one second boundary
for powersaving.
On resume, the driver should check for link up immediately, to
get online faster (rather than waiting for the next second).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The chip executes microcode present in internal RAM,
whose content is loaded from EEPROM on power cycle.
This patch allows an update of the microcode through PIO
without forcing a power cycle.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update FW to 4.1.
Proceed to subsequent HW tuning to improve RDMA perfs..
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Streamline sge page management.
Fix dma mappings when buffers are recycled.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent gcc versions emit warnings when unsigned variables are compared < 0 or >= 0.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Whitespace updates for usbnet core, mostly switching to tab-only indents.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If connected via SGMII, initialize with SGMII mode configured.
Signed-off-by: Kapil Juneja <Kapil.Juneja@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add code for initialising and configuring TBI interface and
programming it for connecting to on-chip SERDES (Lynx PHY)
in case of SGMII mode selected through HRCW at reset.
also add defines for TBI register configuration. TBI
interface is programmed towards the SERDES.
refactored mdio read/write functions to differentiate
programming local interface MII regs (e.g., for TBI) from
always programming the mdio master (TSEC1, for programming
the PHYs).
Signed-off-by: Kapil Juneja <Kapil.Juneja@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ICPlus IP175C sports a 100Mbit/s 4-port switch in addition
to a dedicated 100Mbit/s WAN port.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds PCI error recovery support to the
s2io 10-Gigabit ethernet device driver. Third revision,
blocks interrupts and the watchdog.
Tested, seems to work well.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Ramkrishna Vepa <Ramkrishna.Vepa@neterion.com>
Cc: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Cc: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver version number has not been updated since the driver was
included in the main kernel tree and there is no plan on updating this
in the future either. At this point, the only correct way to refer to
the version is to use the kernel version. The 0.4.4 version is
confusing since there are external version with higher version number
even though they are not actually any newer than the in-tree version.
Let's get rid of the version number in the kernel tree in order to
avoid this kind of confusion.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use list_for_each_entry() instead of manual iteration and
substitute some list_for_each() loops with list_for_each_entry().
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This may be useful in mesh setups when most stations act as repeaters only.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A disagreement between the specifications and the bcm43xx code has just
been discovered and is hereby fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor driver code suggests that CR47 patching happens on every channel
change for every RF (depending on bit 8 in POD).
Due to a bug in their driver (upper bits of RF_Mode get zeroed out, then
are examined for 1s when setting some other flags), this isn't actually
what happens, and their generic CCK patching routine never takes effect.
Some of their RF configurations do include explicit (duplicated) code
for CR47 patching though. This patch makes zd1211rw match that
behaviour.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for another radio appearing in new devices: the
Ubec UW2453. It's more complicated than the other RF's we support, but
Ubec publish full tech specs so we're able to understand the vendor code
relatively well.
Now that we support UW2453, we also support Atheros' new USB chip: the
AR5007UG. From the little info we have, this appears to be just a
rebranded ZD1211B.
This RF code doesn't work very well -- lots more TX/RX errors than the
other RFs. However, the vendor driver doesn't do any better, so this is
all we can do for now.
[kune@deine-taler.de: bug fixes]
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These changes are needed for UW2453 RF support:
Add pointer which RF drivers can use to store private RF data
Add exit hook so that RF drivers can free private data
Allow RF's to disable the generic TX power integration handling code
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Guy Gallagher
zd1211 chip 0586:3407 v4721 high 00-13-49 AL2230_RF pa0 g---
FCC ID SI5WUB200Z
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add top-of-file comment blocks to rtl818x headers and attribute origin
of magic values to original r8187 driver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
93cx6 datasheet available here:
http://ww1.microchip.com/downloads/en/DeviceDoc/21749F.pdf
Figure 1-1 and Table 1-2 on pages 4-5 indicate that both Clock High
Time and Clock Low Time have largest minimum times of 450ns.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a mac80211 based wireless driver for the rtl8187 USB
wireless card.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will add a comment for the 1us delay which is taken
after the pulse has been switched. The 1us delay is based
on the specifications so that should be made clear.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a library for reading from 93cx6 eeproms.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PIO4 is a maximum PIO mode supported by a driver. Using "255" as a max_mode
argument to ide_get_best_pio_mode() could result in wrong timings being used
by a driver (for "pio" equal to 5) or OOPS (for "pio" values > 5 && < 255).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reviewed-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
The SiS966 has one additional PCI-ID 1180.
If the chipset is using this PCI-ID, the primary channel is connected to the
first PATA-port. The secondary channel is connected to SATA-ports in IDE
emulation mode. The legacy IO-ports are used.
The including of the PCI-ID into pata_sis is not sufficient, because the legacy
driver in drivers/ide is initialized before pata_sis.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In 7d12e780e0 David Howells performed
this evolution:
"IRQ: Maintain regs pointer globally rather than passing to IRQ handlers"
He correctly updated many of the function definitions that were using this
extra regs pointer parameter but forgot to update some caller sites of
those functions. The reason the modifications was not properly done on all
drivers is that some drivers were rarely compiled because they are for
AMIGA, or that some code sites were inside #ifdefs where the option is not
set or inside #if 0.
Here is the semantic patch that found the occurences
and fixed the problem.
@ rule1 @
identifier fn;
identifier irq, dev_id;
typedef irqreturn_t;
@@
static irqreturn_t fn(int irq, void *dev_id)
{
...
}
@@
identifier rule1.fn;
expression E1, E2, E3;
@@
fn(E1, E2
- ,E3
)
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we enable the SMCf010 IR device, the Toshiba Portege 4000 BIOS claims
the device is working, but it really isn't configured correctly. The BIOS
*will* configure it, but only if we call _SRS after (1) reversing the order
of the SIR and FIR I/O port regions and (2) changing the IRQ from
active-high to active-low.
This patch addresses the 2.6.22 regression:
"no irda0 interface (2.6.21 was OK), smsc does not find chip"
I tested this on a Portege 4000. The smsc-ircc2 driver correctly detects
the device, and "irattach irda0 -s && irdadump" shows transmitted and
received packets.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: document some of keycodes
Input: add a new EV_SW SW_RADIO event, for radio switches on laptops
Input: serio - take drv_mutex in serio_cleanup()
Input: atkbd - use printk_ratelimit for spurious ACK messages
Input: atkbd - throttle LED switching
Input: i8042 - add HP Pavilion ZT1000 to the MUX blacklist
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Update defconfigs
[POWERPC] Uninline and export virq_to_hw() for the pasemi_mac driver
[POWERPC] Fix PMI breakage in cbe_cbufreq driver
[POWERPC] Disable old EMAC driver in arch/powerpc
Yeah, we could have just disabled it, but there's work on a new one that
isn't as fundamentally broken, so there really doesn't seem to be any
point in keeping it around.
The recent timer cleanup broke the only valid use, and when I say
"valid", I obviously mean "totally broken". So it's not like it works,
or really even can work in the current format that uses the unsafe
"panic" LED blinking routines..
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/ide/setup-pci.c: In function 'ide_scan_pcibus':
drivers/ide/setup-pci.c:879: warning: ignoring return value of '__pci_register_driver', declared with attribute warn_unused_result
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Recently the PLL input clock of Promise 2027x is sometimes detected
higher than expected (e.g. 20.027 MHz compared to 16.714 MHz).
It seems sometimes the mdelay() function is not as precise as it
used to be. Per Alan's advice, HT or power management might affect
the precision of mdelay().
This patch calls gettimeofday() to measure the time elapsed and
calculate the PLL input clock accordingly.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bahadir Balban <bahadir.balban@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
SWDMA modes are unsupported by it821x. Attempts to tune SWDMA modes always
fail (due to sanity check in ->speedproc) and result in PIO being tuned.
* Fix incorrect SWDMA mask so core code won't try these modes and will just
tune PIO if no other DMA modes are available.
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
* Driver can't skip programming transfer mode on the device in amd_set_drive()
(similar fix has been applied to via82cxxx driver ages ago).
* While at it remove redundant warning (ide_config_drive_speed() already
produces more valuable one).
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The HPT36x chips finally turned out to have the channel enable bits -- however,
badly implemented. Make use of them despite it's probably only going to burden
the driver's code -- assuming both channels are always enabled by the HighPoint
BIOS anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Cc: michal.kepien@poczta.onet.pl
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add the MAXTOR STM3320620A drive into the UltraDMA/66 mode blacklist
for the HPT36x chips.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Found by a static analyser. It is in theory possible we dereference
dev->id when it has become invalid. Re-order to avoid this.
Not needed for new-ide as we no longer support the crazy exabyte nest stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Look at wait_drive_not_busy in drivers/ide/ide-taskfile.c:
static u8 wait_drive_not_busy(ide_drive_t *drive)
{
ide_hwif_t *hwif = HWIF(drive);
int retries = 100;
u8 stat;
/*
* Last sector was transfered, wait until drive is ready.
* This can take up to 10 usec, but we will wait max 1 ms
* (drive_cmd_intr() waits that long).
*/
while (((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) && retries--)
udelay(10);
if (!retries)
printk(KERN_ERR "%s: drive still BUSY!\n", drive->name);
return stat;
}
`printk' is never called because `retries' never holds zero at the
outside of `while' loop: when `retries' holds zero at the while's loop
condition, `retries' will hold -1 at the if condition.
Signed-off-by: Masatake YAMATO <jet@gyve.org>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: joe@perches.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
if the call to budget_register() fails in ttpci_budget_int(),
ttpci_budget_init() returns success. The attached patch will
fix this problem.
Signed-off-by: Hartmut Birr <e9hack@googlemail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Spotted and tested by Thomas Sattler <tsattler@gmx.de>.
cinergyT2.c does cancel_delayed_work() + flush_scheduled_work() while
holding cinergyt2->sem. This leads to deadlock because work->func()
needs the same mutex to complete. Another bug is that this code in fact
can't reliably stop the re-arming delayed_work.
Convert this code to use cancel_rearming_delayed_work() and move it
out of ->sem. Another mutex, ->wq_sem, was added to protect against the
concurrent open/resume.
This patch is a horrible hack to fix the lockup which happens in practice.
As Dmitry Torokhov pointed out this driver has other problems and needs
further changes.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
v4l-info and other programs would loop indefinitely while querying the
tuners for cx88-blackbird cards.
The cause was that vidioc_g_tuner didn't return an error value for
qctrl->id != 0, making the application think there is a never ending
list of tuners...
This patch adds the same index check as done in vidioc_g_tuner() in
cx88-video.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If one uses a V4L *one* application, such as vlc or mplayer's v4l driver, as
the first user after the driver is loaded, the driver wedges itself and will
never capture properly. Even if one uses a V4L2 application later, it still
won't work.
If one uses a V4L *two* application first, such as tvtime or mplayer's v4l2
driver, then the driver will be ok. One can then run a V4L1 application, and
it will work.
It turns out the problem is with norm changing and the crop support that was
added in 2.6.21. The driver defaults to PAL, and keeps the last norm it was
set too across opens. If one changes the norm via V4L1, the cropping
parameters are not reset like they should be, and they'll remain broken across
device opens.
This patch removes the direct setting of btv->tvnorm in the V4L1 ioctl
VIDIOCSCHAN handler. The norm is set via the existing call to set_input(),
which calls set_tvnorm(), which will reset the cropping values now that it is
able to detect the norm change.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
PCMCIA doesn't use DMA and as this driver is used on many platforms we
don't want it to fail on those that define the DMA alloc API as a NULL
return
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We got it backwards and now the other detects are fixed it shows up
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
host->irq and host->irq2 should be set before ata_host_register() for
IRQ reporting to work. Move up host->irq assignment in
ata_host_activate() and add it to ata_pci_init_one() native path and
pata_cs5520.
The port info printing in ata_host_register() doesn't fit all the
different controllers. It should probably be moved out to LLDs with
some helpers in the future.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to check for special case "acpi_osi=!Linux" before handling the
general case "acpi_osi=!*", or it will have no effect.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
3c589_cs: fix local_bh_enable warning
RESEND [PATCH 3/3] NetXen: Graceful teardown of interface and hardware upon module unload
drivers/net/ns83820.c: fix a check-after-use
net/usb/cdc_ether minor sparse cleanup
RESEND [PATCH 2/3] NetXen: Support per PCI-function interrupt mask registers
RESEND [PATCH 1/3] NetXen: Fix issue of MSI not working correctly
dm9601: Return 0 from bind() on success
Update MAINTAINERS for USB network devices
usbnet: Zero padding byte if there is tail room in skb
dm9601: HW header size shouldn't be included in packet length
starfire list alpha as 64 bit arch
myri10ge: SET_NETDEV_DEV()
gianfar: Fix typo bug introduced by move to udp_hdr()
[PATCH] libertas: remove private ioctls
[PATCH] libertas: fix WPA associations by handling ENABLE_RSN correctly
[PATCH] libertas: kill wlan_scan_process_results
[PATCH] libertas: style fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: add Kconfig help on building both stacks
firewire: fix async reception on big endian machines
If a page can't be allocated for the frag list of a skb, the code to
unmap the partially allocated list is off by one. For exaple, if
'frags' equals one, i == 0, and the alloc_page() fails, then the old
loop would have unmapped mapping[1] which is uninitialized. The same
would happen if the call to ib_dma_map_page() failed.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Acked-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Russell King wrote:
> Having upgraded from 2.6.16 to 2.6.22-rc6, I'm now seeing the following.
>
> Looks like netfilter is calling local_bh_enable() with IRQs disabled,
> which would appear to be illegal. Thankfully, this is a warn-once
> warning.
>
> WARNING: at /home/rmk/git/linux-2.6-rmk/kernel/softirq.c:138 local_bh_enable()
> [...]
> [<c01447fc>] (nf_conntrack_destroy+0x0/0x2c) from [<c012c05c>] (__kfree_skb+0xd0/0x100)
> [<c012bf8c>] (__kfree_skb+0x0/0x100) from [<c012c0d8>] (kfree_skb+0x4c/0x50)
> r5:c12a3800 r4:00000300
> [<c012c08c>] (kfree_skb+0x0/0x50) from [<bf03cbb0>] (el3_start_xmit+0xb8/0xd0 [3c589_cs])
> [<bf03caf8>] (el3_start_xmit+0x0/0xd0 [3c589_cs]) from [<c01324dc>] (dev_hard_start_xmit+0x1a8/0x244)
> r7:c12a3800 r6:c1a9aa00 r5:c1a9aa00 r4:c12a3800
> [<c0132334>] (dev_hard_start_xmit+0x0/0x244) from [<c013fcc0>] (__qdisc_run+0xb0/0x198)
Thats a bug in the 3c589_cs driver. Patch attached.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changed PATA handler for PATA-ports used by sata_sis.
This patch was originally submitted by Jeff Garzik.
Added PCI-ID 1180 for SiS966 Controller in pata_sis.
The 1180 mode is fully compatible to other SiS PATA-controller.
The PCI-ID 1183 is SATA in PATA-emulation, but not fully compatible
to SiS5513/5518. sata_sis.c is forwarding this ID to pata_sis.
1183 is not working if simply added to pata_sis.
This handling fixes issues with SiS968.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Another member of HTS5416* family doing spurious NCQ completion.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Enrico Sardi <enricoss@tiscali.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sata_nv driver was missing the change_queue_depth hook in the SCSI host
template which the other NCQ-capable libata drivers had. This made it impossible
to change the queue depth by user request. Add this in.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_inic162x can't do LBA48 properly yet and is likely to corrupt
data on drives larger than LBA28 limit. Disable LBA48 devices during
device configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In ata_hsm_qc_complete():
Calling ata_altstatus() after the qc is completed might race with next qc. Remove it.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recently the PLL input clock of pata_pdc2027x is sometimes detected
higer than expected (e.g. 20.027 MHz compared to 16.714 MHz).
It seems sometimes the mdelay() function is not as precise as it
used to be. Per Alan's advice, HT or power management might affect
the precision of mdelay().
This patch calls gettimeofday() to mesure the time elapsed and
calculate the PLL input clock accordingly.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Mon, 11 Jun 2007 20:28:16 +0200 api wrote:
> Good day,
> When doing make menuconfig one comes across CONFIG_BLK_DEV_SD.
> The help file states that this is for scsi disks.NO MENTION IS MADE THAT
> IT IS NEEDE FOR SATA DISKS AS WELL!
> Would have saved me a lot of time if the help was up to date.
> I hope this can be changed so others can make a kernel for sata systems
> quicker.
From: Randy Dunlap <randy.dunlap@oracle.com>
Add help info for BLK_DEV_SD referring to its use in
SATA or PATA driver configurations.
Add help text for "ATA" indicating that it probably needs
some SCSI config symbols enabled in order to be useful.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resending patch 3/3 only.
These changes allow driver close routine to be called during module unload,
to clean-up buffers and other software resources, flush queues etc. Also,
hardware is reset to pristine state.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove an "sparse" warning about a shadowed variable name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch updates the various access routines to access different
control and status settings present in different register locations.
This will fix problems related to working of different ports in
multi Port card.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen driver uses PCI function 0 to provide the functionality of MSI.
The patch makes driver check the bus master bit for function 0 and
enable it after the card initialization.
Signed-off-by: Dhananjay Phadke<dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixup dm9601_bind() so it returns 0 on success rather than just a positive
number, as otherwise usbnet doesn't init the status handler.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Usbnet adds a padding byte if a 0 byte USB packet would be sent. Zero
padding byte if there is tail room in skb.
Signed-of-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The dm9601 driver was including the 2 byte hardware header in the
packet length, causing the HW to send 2 extra bytes of garbage on tx.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
instead of:
"This driver has not been ported to this 64-bit architecture yet."
the driver is said to work on alpha, see
http://bugs.debian.org/305330
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SET_NETDEV_DEV() in myri10ge to create the "/sys/class/net/<if>/device"
symlink.
Signed-off-by: Maik Hampel <m.hampel@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The EMAC driver, in drivers/net/ibm_emac, for the embedded Ethernet
MAC found in PowerPC 4xx embedded chips is not suitable for
arch/powerpc. It will not build because it relies on the old arch/ppc
OCP mechanism. BenH has a new, device-tree aware version of the
driver which will work in arch/powerpc, but until it's merged, this
patch will disable the old, non-building version.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Don't use PNP detection by default yet. We have some PNP and BIOS issues
to work out first.
Sample problem on a Toshiba Portege 4000: the SMCf010 device is handed off
disabled. We assign I/O ports originally assigned to the SMCf010 to a
PCMCIA device instead. We enable the SMCf010, configuring it to use
disjoint ports, but _SRS doesn't work correctly, so the device doesn't
work.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If asus_acpi_init doesn't find any device it knows about, it mistakenly
returns a "success" error code even though it cleans up after itself. Later
when trying to rmmod asus_acpi, the module_exit routine would try to clean up
one more time and we would end up calling
acpi_bus_unregister_driver(&asus_hotk_driver) twice. This patch addresses
this first problem by returning -ENODEV when no appropriate device is found.
Then there was also another bug with the code handling the return value of
backlight_device_register. If this function ever failed, the driver would
cleanup by calling the module_exit routine from module_init, but it would
still return "success". So any attempt to rmmod this module would result in
asus_acpi_exit being called twice but it's not ready to handle it (I haven't
hit this bug, just found it by code inspection). This patch fixes that by
inserting a return -ENODEV; at the end of this error handling path.
Signed-off-by: Maxime Austruy <maxime@tralhalla.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The blink driver wakes up every jiffies which wastes power unnecessarily.
Using a notifier gives same effect. Also add ability to unload module.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
[ We should really just delete the whole thing. The blink driver is
broken in many other ways too -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alas that won't work so good, because nobody reads help texts.
I thought about adding some crude multiple choice selection (build the
old stack, build the new stack, build both stacks). It's possible, but
it would introduce awkward dummy config variables.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
descriptor.data_address is little endian
Tested-by: Olaf Hering <olh@suse.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Fix printk format warning:
drivers/net/irda/irport.c:512: warning: format '%d' expects type 'int', but argument 5 has type 'long int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4bedb45203 both the udp and tcp
cases where changed to use udp_hdr() instead of leaving the tcp case
alone and fixing with tcp_hdr().
This ended up causing random behavior with TCP connections because
of looking for tcp_hdr()->check in the wrong place.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need to take serio->drv_mutex in serio_cleanup() to prevent the
function from being called while driver is in the middle of attaching
to a serio port. Such situation can happen with i8042 and atkbd drivers
if user rapidly presses Ctrl-Alt-Del during system startup, and leads
to kernel oops.
Reported-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The interrupt clearing code in mpsc_sdma_intr_ack() mistakenly clears the
interrupt for both controllers instead of just the one its supposed to.
This can result in the other controller appearing to hang because its
interrupt was effectively lost.
So, don't clear the interrupt cause bits for both MPSC controllers when
clearing the interrupt for one of them. Just clear the one that is
supposed to be cleared.
Signed-off-by: Jay Lubomirski <jaylubo@motorola.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/built-in.o(.text+0x8742a): Section mismatch: reference to .init.data:chipsfb_fix (between 'chipsfb_pci_init' and 'chipsfb_set_par')
WARNING: drivers/built-in.o(.text+0x87432): Section mismatch: reference to .init.data:chipsfb_fix (between 'chipsfb_pci_init' and 'chipsfb_set_par')
WARNING: drivers/built-in.o(.text+0x87442): Section mismatch: reference to .init.data:chipsfb_var (between 'chipsfb_pci_init' and 'chipsfb_set_par')
WARNING: drivers/built-in.o(.text+0x8744a): Section mismatch: reference to .init.data:chipsfb_var (between 'chipsfb_pci_init' and 'chipsfb_set_par')
init_chips is only called from chipsfb_pci_init
chipsfb_fix and chipsfb_var are only referenced from init_chips
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the test for the thread pid from >= 0 to > 0.
When the saa8134 driver initialization fails after a certain point, it goes
through the complete shutdown process for the driver. Part of shutting it
down includes tearing down the thread for tv audio.
The test for tearing down the thread tests for >= 0. Since the dev
structure is kzalloc'd, the test will always be true if we haven't tried to
start the thread yet. We end up waiting on pid 0 to complete, which will
never happen, so we lock up.
This bug was observed in Novell Bugzilla 284718, when request_irq() failed.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename struct pci_driver data so that false section mismatch warnings won't
be produced.
Sam, ISTM that depending on variable names is the weakest & worst part of
modpost section checking. Should __init_refok work here? I got build
errors when I tried to use it, probably because the struct pci_driver probe
and remove methods are not marked "__init_refok".
WARNING: drivers/dma/ioatdma.o(.data+0x10): Section mismatch: reference to .init.text: (between 'ioat_pci_drv' and 'ioat_pci_tbl')
WARNING: drivers/dma/ioatdma.o(.data+0x14): Section mismatch: reference to .exit.text: (between 'ioat_pci_drv' and 'ioat_pci_tbl')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Chris Leech <christopher.leech@intel.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If one has a dependency chain (tristate)FOO depends on (bool)BAR depends on
(tristate)BAZ, build problems will result. If BAZ=m, then BAR can be set
y, which allows FOO=y. It's possible to have FOO=y && BAZ=m, which
wouldn't be allowed if FOO depended directly on BAZ. In effect, the bool
promotes the tristate from m to y.
This ends up causing a problem with several menuconfigs that look like:
menuconfig BAR
bool
depends on BAZ [tristate]
if BAR
config FOO
tristate
endif
The solution used here is to add the dependencies of BAR to the if
statement, so that items in the if block will gain a direct
non-bool-promoted dependency on BAZ. This is how it would work if a menu
was used instead of an if block.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some HP firmware leaves the SMCf010 IRDA device incompletely configured, or
reports the wrong resources in _CRS. As a workaround, when we find such a
device, try to auto-configure the device.
This ignores the _CRS data, picks a config from _PRS, and runs _SRS to
configure the device. This makes smsc-ircc2 work correctly with PNP
resources (with no preconfiguration!) on all the machines I tested.
I think Windows does something like this by default for all devices,
so we should consider doing the same thing in Linux.
This patch addresses part of the 2.6.22 regression:
"no irda0 interface (2.6.21 was OK), smsc does not find chip"
It fixes smsc-ircc2 PNP device detection on HP nc6000, nc6220, nw8000,
nw8240, and possibly other machines.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we rely on the device resources from PNPBIOS, we also have to rely on
the BIOS to configure any bridges on the way to the device.
Using the PNPBIOS resources but changing the configuration of a bridge
behind the back of the firmware is likely to make things inconsistent.
This patch addresses part of the 2.6.22 regression:
"no irda0 interface (2.6.21 was OK), smsc does not find chip"
It fixes smsc-ircc2 PNP device detection on HP nx5000 laptops.
Other laptops, including HP nc6000, HP nc8000, HP nw8000, and Toshiba
Portege 4000, still need PNP quirks to make this work.
With "smsc-ircc2.nopnp", we do the legacy device probe, including manual
bridge preconfiguration, as before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Acked-by: "Linus Walleij (LD/EAB)" <linus.walleij@ericsson.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a regression on Apple iBook1. Changes in the clock init code caused an
incorrect XCLK frequency to be used leading to a corrupted display.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: Olaf Hering <olaf@aepfle.de>
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The phy_id specified for the Vitesse 824x PHY would never match because
it was expecting bits to be set that would be masked by the phy_id_mask.
Fix the phy_id so it will match properly, and changed the mdio_bus_match
to mask both the driver and devices phy_id with the mask so we dont have
this issue in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Don't clobber the firmware's internal state machine by setting
ENABLE_RSN more than once during the 4-way handshake. Check what
the ENABLE_RSN status is and only set if it should be changed.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fold into wlan_scan_networks() and protect with debug defines.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some boxes keyboard controllers are too slow to withstand
continuous flow of requests to turn keyboard LEDs on and off
and start losing some keypresses or even all of them.
Delay executing of LED switching request if we had another one
within 50 ms thus easing load on the controller.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This should get rid of "atkbd.c: Suprious NAK on isa0060/serio0"
messages caused by broken MUX implementation. The box does not
have external PS/2 ports and, according to documentation,
automatically disables touchpad when an external mouse is plugged
into a port replicator, so MUX mode would not work anyway.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds support for some of the XGI Volari family that are based on the
SiS.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ATA_HORKAGE_DMA_RW_ONLY for TORiSAN is verified to be subset of using
DMA for ATAPI commands which aren't aligned to 16 bytes. As libata
now doesn't use DMA for unaligned ATAPI commands, the horkage is
redundant. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The IDE driver used DMA for ATAPI commands if READ/WRITE command is
multiple of sector size or sg command is multiple of 16 bytes. For
libata, READ/WRITE sector alignment is guaranteed by the high level
driver (sr), so we only have to worry about the 16 byte alignment.
This patch makes ata_check_atapi_dma() always request PIO for all data
transfer commands which are not multiple of 16 bytes.
The following reports are related to this problem.
http://bugzilla.kernel.org/show_bug.cgi?id=8605 (confirmed)
http://thread.gmane.org/gmane.linux.kernel/476620 (confirmed)
https://bugzilla.novell.com/show_bug.cgi?id=229260 (probably)
Albert first pointed out the difference between IDE and libata. Kudos
to him.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In atapi_xlat(), prepare qc better before calling
ata_check_atapi_dma() such that ata_check_atapi_dma() can use info
from qc. While at it, reformat weird looking if/else block in the
function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When EH gives up after repeated exceptions, it doesn't't clear the
PENDING bit on exit which leaves PENDING bit set without EH actually
scheduled. This makes ata_port_wait_eh() to wait forever makes rmmod
hang on such port. Fix it by clearing the flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix section mismatch when CONFIG_HOTPLUG=n (but functions are used
for resume):
WARNING: drivers/ata/pata_it821x.o(.text+0x3f): Section mismatch: reference to .init.text: (between 'it821x_reinit_one' and 'it821x_program_udma')
WARNING: drivers/ata/pata_it821x.o(.text+0x691): Section mismatch: reference to .init.text: (between 'it821x_init_one' and 'it821x_passthru_set_dmamode')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's no reason to print out hpa related messages when HPA is not
active. Kill the unconditional message and add a warning message
which is printed if HPA size is smaller than the current size.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
prereset() is now allowed to set flag for unsupported reset method.
EH layer is responsible for selecting the fallback. Remove non-sense
warning message.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Tue, Jun 19, Stephen Hemminger wrote:
> Olaf Hering <olaf@aepfle.de> wrote:
> > What happend to __ucmpdi2 from David Woodhouse?
> > google has a few hits about stuff like this on 32bit powerpc with gcc 4.1.2:
> >
> > ERROR: "__ucmpdi2" [drivers/net/s2io.ko] undefined!
> >
> > using the drivers/net/s2io* files from 2.6.21 with 2.6.22-rc5 fixes the
> > compile.
> >
> > 25805dcf9d adds two u64 >>= 48 followed by
> > a switch statement (line 2889 and 6816).
>
> Probably the "switch(err) {" needs a cast to a smaller type (like u8).
This change removes the compiler-generated calls to __ucmpdi2.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed by including <linux/dma-mapping.h>:
CC drivers/net/au1000_eth.o
drivers/net/au1000_eth.c: In function 'au1000_probe':
drivers/net/au1000_eth.c:661: warning: implicit declaration of function 'dma_alloc_noncoherent'
drivers/net/au1000_eth.c:802: warning: implicit declaration of function 'dma_free_noncoherent'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reported by Grzegorz Chimosz <gchimi@gmail.com>
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_unlink_urb() is asynchronous, therefore an URB's buffer may not
be freed without waiting for the completion handler. This patch switches
to usb_kill_urb(), which is synchronous.
Thanks to Alan for making me look at the remaining users of usb_unlink_urb()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usblcd currently has no way to limit memory consumption by fast writers.
This is a security problem, as it allows users with write access to this
device to drive the system into oom despite resource limits.
Here's the fix taken from the modern skeleton driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is a classical memory leak in the ioctl handler. The buffer is simply
never freed. This fixes it the obvious way.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
you are submitting an URB with GFP_KERNEL holding a spinlock.
In this case the spinlock can be dropped earlier.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New changes in the signal-handling code require compensating changes
in g_file_storage. This patch (as913) by Oleg Nesterov makes the
code use allow_signal() instead of sigprocmask().
From: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: Make skb_seq_read unmap the last fragment
[NET]: Re-enable irqs before pushing pending DMA requests
[TCP] tcp_read_sock: Allow recv_actor() return return negative error value.
[PPP]: Fix osize too small errors when decoding mppe.
[PPP]: Revert 606f585e36
[TIPC]: Fix infinite loop in netlink handler
[SKBUFF]: Fix incorrect config #ifdef around skb_copy_secmark
[IPV4]: include sysctl.h from inetdevice.h
[IPV6] NDISC: Fix thinko to control Router Preference support.
[NETFILTER]: nfctnetlink: Don't allow to change helper
[NETFILTER]: nf_conntrack_sip: add missing message types containing RTP info
The stallion driver oopses while initializing ISA cards due to an
uninitialized variable. This patch changes the initialisation order to
match the PCI code path.
Signed-off-by: Ingo Korb <ml@akana.de>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When binding the driver, check the ID register for a valid identity, in case
the SM501 is not functioning correctly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ensure that the M1XCLK and MCLK are sourced from the same PLL (and refuse to
bind the driver if they are not).
Update the PCI to safe initialisation values, as 72MHz is the maximum clock
for 33MHz PCI bus mastering.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The order of the set and mask operation in sm501_init_reg() was setting and
then masking the bits set. Correct the order so that we do not end up with
288MHz SDRAM clocks on certain systems.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This init sequence of setting the SDRAM clock before the bus clock is
recommend by Silicon Motion to stop problems with writes not sticking into
registers.
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for suspending the core (mfd driver) of the SM501.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently my console UTF-8 patch went mainline. Here is an additional patch
that fixes two nasty issues and improves a third one, namely:
1. My patch changed the behavior if a glyph is not found in the Unicode
mapping table. Previously for Unicode values less than 256 or 512 the
kernel tried to display the glyph from that position of the glyph table,
which could lead to a different accented letter being displayed. I
removed this fallback possibility and changed it to display the
replacement symbol.
As Behdad pointed out, some fonts (e.g. sun12x22 from the kbd package)
lack Unicode mapping information, hence all you get is lots of question
marks. Though theoretically it's actually a user-space bug (the font
should be fixed), Behdad and I both believe that it'd be good to work
around in the kernel by re-introducing the fallback solution for ASCII
characters only. This sounds a quite reasonable decision, since all fonts
ship the ASCII characters in the first 128 positions. This way users
won't be surprised by lots of question marks just because s/he issued a
not-so-perfectly parameterized setfont command. As this fallback is only
re-introduced for code points below 128, you still won't see an accented
letter replaced by another, but at least you'll always get the English
letters right.
2. My patch introduced "question mark with inverted color attributes" as a
last resort fallback glyph. Though it perfectly works on VGA console, on
framebuffer you may end up with question marks that are highlighed but
shouldn't be, and normal characters that are accidentally highlighed.
This is caused by missing FLUSHes when changing the color attribute.
3. I've updated the table of double-width character based on Markus's
updated version. Only ten new code poings (one interval) is added.
Signed-off-by: Egmont Koblinger <egmont@uhulinux.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mppe_decompress() function required a buffer that is 1 byte too
small when receiving a message of mru size. This fixes buffer
allocation to prevent this from occurring.
Signed-off-by: Konstantin Sharlaimov <konstantin.sharlaimov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can cause packet buffer overflows in certain cases,
the real bug will be fixed differently in a followon
changeset.
Signed-off-by: David S. Miller <davem@davemloft.net>
Always disable/enable interrupts in the acpi idle routine,
even in the error path.
This is required as the 2.6.20 change in git commit d331e739f5ad2aaa9...
"Fix interrupt race in idle callback" expects the idle handler
to enable interrupt before returning.
There was a case in acpi idle routine, in which interrupt was not being
enabled before return, which caused the system to hang at bootup, while
enabling C-states on an SMP system.
The signature of the hang was that "processor.nocst"
was required to enable boot.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Include PPC_MAC in the default too, not only MAC which only covers
m68k MACs.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Correct max_srq_wr returned from mlx4_ib_query_device()
IPoIB/cm: Remove dead definition of struct ipoib_cm_id
IPoIB/cm: Fix interoperability when MTU doesn't match
IPoIB/cm: Initialize RX before moving QP to RTR
IB/umem: Fix possible hang on process exit
We need to keep a spare entry in the SRQ so that there always is a
next WQE available when posting receives (so that we can tell the
difference between a full queue and an empty queue). So subtract 1
from the value HW gives us before reporting the limit on SRQ entries
to consumers.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB connected mode currently rejects a connection request unless the
supported MTU is >= the local netdevice MTU. This breaks
interoperability with implementations that might have tweaked
IPOIB_CM_MTU, and there's real no longer a reason to do so: this test
is just a leftover from when we did not tweak MTU per-connection. Fix
this by making the test as permissive as possible.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a crasher bug in IPoIB CM: once a QP is in the RTR state, a
receive completion (or even an asynchronous error) might be observed
on this QP, so we have to initialize all of our receive data
structures before moving to the RTR state.
As an optimization (since modify_qp might take a long time), the
jiffies update done when moving RX to the passive_ids list is also
left in place to reduce the chance of the RX being misdetected as
stale.
This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=662>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If ib_umem_release() is called after ib_uverbs_close() sets context->closing,
then a process can get stuck in a D state, because the code boils down to
if (down_write_trylock(&mm->mmap_sem))
down_write(&mm->mmap_sem);
which is obviously a stupid instant deadlock. Fix the code so that we
only try to take the lock once.
This bug was introduced in commit f7c6a7b5 ("IB/uverbs: Export
ib_umem_get()/ib_umem_release() to modules") which fortunately never
made it into a release, and was reported by Pete Wyckoff <pw@osc.edu>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After i915 chip, GMCH has no AGP port. Origin bridge driver in device
table will try to access illegal regs like APBASE, APSIZE, etc. This
may cause problem.
So mark them as NULL in the table, we won't load if no IGD got detect
and bridge has no AGP port.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
fix module_param mistake in it821x
ahci: fix PORTS_IMPL override
kerneldoc fix in libata
libata: more NONCQ devices
pata_it821x: (partially) fix DMA in RAID mode
PATA: Add the MCP73/77 support to PATA driver
The attached patch fixes a trivial
mistake in a MODULE_PARAM_DESC of pata_it821x
driver. The parameter name in MODULE_PARAM_DESC
should match the one in module_param_named.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If PORTS_IMPL register is zero, ahci initialize it to full mask
corresponding to nr_ports in the CAP register. hpriv->cap, which is
initialized at the end of the function, is incorrectly used as value
of CAP causing ahci to always override PORTS_IMPL to 0x1 if it's zero.
Fix it.
This fixes a bug where early ich6 ahci can only access the first port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix parameter name from ata_dev_reread_id() in libata-core.c for kerneldoc.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More for the NCQ blacklist. One hitachi and one raptor. Other
members of these families of drives are already on the list, so no
surprises.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code intended to check DMA status was checking DMA command register.
Moreover firmware seems to "forget" to set DMA capable bit for the
slave device (at least in RAID mode but without ITE RAID volumes) so
check device ID for DMA capable bit when deciding whether to use DMA
and remove DMA status check completely.
Thanks to Pavol Simo for the bugreport and testing the initial fix.
This change unfortunately still doesn't fix DMA in RAID mode (which
works fine with IDE it821x) but Alan is working on the missing pieces
(pata_it821x vs libata EH issues).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the MCP73/MCP77 support to PATA driver.
The patch base on kernel 2.6.22-rc4
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rx traffic needs to be halted when the MTU is changed
to avoid a potential chip hang.
Reset/restore MAC filters around a MTU change.
Also fix the pause frames high materwark setting.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Check all lanes for link status on direct XAUI cards.
Don't assume that direct XAUI always uses XGMAC 1.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix netpoll handler to work with line interrupt, msi and msi-x.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
eth_type_trans() now sets skb->dev.
References to skb->dev should happen after it is called.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The spinlock irq flags should be a unsigned long to properly support 64 bit
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I happened to notice that a system with an NVidia NIC using the
forcedeth driver won't wake-on-LAN if the interface was in promiscuous
mode when you power off. By experiment, it looks like
the hardware needs to have NvRegPacketFilterFlags set to
NVREG_PFF_ALWAYS|NVREG_PFF_MYADDR (i.e., receive unicast packets to my
address) in order for WoL to work.
Jeff Garzik writes: "NVIDIA says the patch looks OK." I didn't venture
to insert a signed-off-by line with his name on it, though.
Signed-off-by: Tim Mann <mann@vmware.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The recent iucv rework patches re-introduced some unnecessary inlines.
Remove them again.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
spinlock initializer cleanup in netiucv.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
net/iucv/iucv.c creates the requirement for
iucv_path_connect not to be called from tasklet context anymore.
An extra checking is added in case of a failing netiucv_tx
to fulfil this requirement for netiucv.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use ccw_device_get_id() to get a device number
instead of parsing the ccw device's bus id.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Packets Length in qdio header is broken when using
EDDP on Layer2 devices. This leads to skb_under_panic on receiver
system when running on z/VM GuestLAN devices.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ipv6_regen_rndid in net/ipv6/addrconf.c makes use of "write_lock_bh"
for its inet6_dev->lock. It may run in softirq-context.
qeth makes use of "read_lock" for the same inet6_dev->lock.
To avoid a potential deadlock situation, qeth should make use of
"read_lock_bh" for its usages of inet6_dev->lock.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While first recovery continues, the card issues
a STARTLAN command itself. In this case qeth
schedules another recovery. This second
recovery is cancelled because of an already running first recovery.
Stop first recovery in case of 0xe080.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For real HiperSockets the EBCDIC-ASCII conversion is not necessary.
This is only needed for z/VM GuestLAN devices.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Modify carrier state determination for 802.3ad mode to comply
with section 43.3.9 of IEEE 802.3, which requires that "Links that are
not successful candidates for aggregation (e.g., links that are attached
to other devices that cannot perform aggregation or links that have been
manually configured to be non-aggregatable) are enabled to operate as
individual IEEE 802.3 links."
Bug reported by Laurent Chavey <chavey@google.com>. This patch
is an updated version of his patch that changes the wording of
commentary and adds an update to the driver version.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Laurent Chavey <chavey@google.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch (based on a patch from Stephen Hemminger
<shemminger@linux-foundation.org>) removes use after free conditions in
the unregister path for the bonding master. Without this patch, an
operation of the form "echo -bond0 > /sys/class/net/bonding_masters"
would trigger a NULL pointer dereference in sysfs. I was not able to
induce the failure with the non-sysfs code path, but for consistency I
updated that code as well.
I also did some testing of the bonding /proc file being open
while the bond is being deleted, and didn't see any problems there.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It doesn't look like spidernet hardware can really checksum all protocols,
the code looks like it does IPV4 only. If so, it should use NETIF_F_IP_CSUM
instead of NETIF_F_HW_CSUM.
The driver doesn't need it's own get/set for ethtool tx csum, and it
should use the standard ethtool_op_get_link.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At some point, the transmit descriptor chain end interrupt (TXDCEINT)
was turned on. This is a mistake; and it damages small packet
transmit performance, as it results in a huge storm of interrupts.
Turn it off.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Although the previous patch resolved issues with hangs when the
RX ram full interrupt is encountered, there are still situations
where lots of RX ramfull interrupts arrive, resulting in a noisy
log in syslog. There is no need for this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The terminated RX ring will cause trouble during the RX ram full
conditions, leading to a hung driver, as the hardware can't find
the next descr. There is no real reason to terminate the RX ring;
it doesn't make the operation any smooother, and it does
require an extra sync. So don't do it.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a rare deadlock that can occur when the kernel
is not able to empty out the RX ring quickly enough. Below follows
a detailed description of the bug and the fix.
As long as the OS can empty out the RX buffers at a rate faster than
the hardware can fill them, there is no problem. If, for some reason,
the OS fails to empty the RX ring fast enough, the hardware GDACTDPA
pointer will catch up to the head, notice the not-empty condition,
ad stop. However, RX packets may still continue arriving on the wire.
The spidernet chip can save some limited number of these in local RAM.
When this local ram fills up, the spider chip will issue an interrupt
indicating this (GHIINT0STS will show ERRINT, and the GRMFLLINT bit
will be set in GHIINT1STS). When te RX ram full condition occurs,
a certain bug/feature is triggered that has to be specially handled.
This section describes the special handling for this condition.
When the OS finally has a chance to run, it will empty out the RX ring.
In particular, it will clear the descriptor on which the hardware had
stopped. However, once the hardware has decided that a certain
descriptor is invalid, it will not restart at that descriptor; instead
it will restart at the next descr. This potentially will lead to a
deadlock condition, as the tail pointer will be pointing at this descr,
which, from the OS point of view, is empty; the OS will be waiting for
this descr to be filled. However, the hardware has skipped this descr,
and is filling the next descrs. Since the OS doesn't see this, there
is a potential deadlock, with the OS waiting for one descr to fill,
while the hardware is waiting for a differen set of descrs to become
empty.
A call to show_rx_chain() at this point indicates the nature of the
problem. A typical print when the network is hung shows the following:
net eth1: Spider RX RAM full, incoming packets might be discarded!
net eth1: Total number of descrs=256
net eth1: Chain tail located at descr=255
net eth1: Chain head is at 255
net eth1: HW curr desc (GDACTDPA) is at 0
net eth1: Have 1 descrs with stat=xa0800000
net eth1: HW next desc (GDACNEXTDA) is at 1
net eth1: Have 127 descrs with stat=x40800101
net eth1: Have 1 descrs with stat=x40800001
net eth1: Have 126 descrs with stat=x40800101
net eth1: Last 1 descrs with stat=xa0800000
Both the tail and head pointers are pointing at descr 255, which is
marked xa... which is "empty". Thus, from the OS point of view, there
is nothing to be done. In particular, there is the implicit assumption
that everything in front of the "empty" descr must surely also be empty,
as explained in the last section. The OS is waiting for descr 255 to
become non-empty, which, in this case, will never happen.
The HW pointer is at descr 0. This descr is marked 0x4.. or "full".
Since its already full, the hardware can do nothing more, and thus has
halted processing. Notice that descrs 0 through 254 are all marked
"full", while descr 254 and 255 are empty. (The "Last 1 descrs" is
descr 254, since tail was at 255.) Thus, the system is deadlocked,
and there can be no forward progress; the OS thinks there's nothing
to do, and the hardware has nowhere to put incoming data.
This bug/feature is worked around with the spider_net_resync_head_ptr()
routine. When the driver receives RX interrupts, but an examination
of the RX chain seems to show it is empty, then it is probable that
the hardware has skipped a descr or two (sometimes dozens under heavy
network conditions). The spider_net_resync_head_ptr() subroutine will
search the ring for the next full descr, and the driver will resume
operations there. Since this will leave "holes" in the ring, there
is also a spider_net_resync_tail_ptr() that will skip over such holes.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Avoid kernel crash in mm/slab.c due to double-free of pointer.
If the ethernet interface is brought down while there is still
RX traffic in flight, the device shutdown routine can end up
trying to double-free an skb, leading to a crash in mm/slab.c
Avoid the double-free by nulling out the skb pointer.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Only set client->iso_context if allocation was successful.
ieee1394: fix to ether1394_tx in ether1394.c
firewire: fix hang after card ejection
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Make sure inline data segments don't cross a 64 byte boundary
IB/mlx4: Handle FW command interface rev 3
IB/mlx4: Handle buffer wraparound in __mlx4_ib_cq_clean()
IB/mlx4: Get rid of max_inline_data calculation
IB/mlx4: Handle new FW requirement for send request prefetching
IB/mlx4: Fix warning in rounding up queue sizes
IB/mlx4: Fix handling of wq->tail for send completions
This patch fixes an OOPS on cdev release for an fd where iso context
creation failed.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
It's already annoying that they appear on x86 now -- that's for the 3button
emulation needed on x86 macs -- but at least don't make them default.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not directly related to x86, but I got tired of seeing these warnings on every
kconfig update when building on a non m68k box:
drivers/input/keyboard/Kconfig:170:warning: 'select' used by config symbol 'KEYBOARD_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
drivers/input/mouse/Kconfig:182:warning: 'select' used by config symbol 'MOUSE_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
I moved the definition of ATARI_KBD_CORE into drivers/input/keyboard/Kconfig
so it's always seen by Kconfig.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Hemminger