Compaq Presario R4000-series laptops are not sending a "volume up button
release" and "volume down button release" signal in the PS/2 protocol for
atkbd. The URL below has some of confirmed reports:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/385477
Signed-off-by: Dave Andrews <jetdog330@hotmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When KBC is in active multiplexing mode, disabling and re-enabling the
touchpad with the special key leaves the touchpad dead. Since the laptop
does not have any external PS/2 ports disabling MUX mode should be safe.
Reported-by: Eugeniy Meshcheryakov <eugen@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes, when using the touchscreen, it stops working till next restart
and the following message is printed:
ucb1400: unexpected IE_STATUS = 0x0
The following patch retriggers the touchscreen interrupt unconditionally.
This prevents hanging of the touchscreen in case of bogus interrupt
occurence.
Signed-off-by: Pavel Revak <palo@bielyvlk.sk>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables ADC filtering on UCB1400 codec by default. The
benefit from this change is mostly on some Colibri boards where
the ADCSYNC pin of the UCB1400 codec isn't connected causing the
touchscreen to jitter very badly. This change has no visible
effect on boards where the ADCSYNC pin is connected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Palo Revak <palo@bielyvlk.sk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The KEY_MAX change in 2.6.28 changed the values of the JSIOCSBTNMAP and
JSIOCGBTNMAP constants; software compiled with the old values no longer
works with kernels following 2.6.28, because the ioctl switch statement
no longer matches the values given by the software. This patch handles
these ioctls independently of the length of data specified, and applies the
same treatment to JSIOCSAXMAP and JSIOCGAXMAP which currently depend on
ABS_MAX.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove assumption on the shift and size of rows/columns form
matrix_keypad driver.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Prestigio 157, an old no-name clone laptop uses input keys very
similar to the Wistron 1557/MS2141 with the addition of BIOS-controlled
wireless radio frequency kill switch.
This patch adds support for the RF kill switch control and adds manual
identification of the model.
The Prestigio does not expose any recognisable identity via dmidecode
and so requires manual selection at module init using
force=1 keymap=prestigio
Signed-off-by: TJ <ubuntu@tjworld.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The synaptic touchpad on the Asus G1S is not properly detected when
rebooting machine or on cold boot from time to time. Adding the Asus
G1S to the noloop exception table resolves the issue.
# dmidecode 2.10
SMBIOS 2.4 present.
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: ASUSTeK Computer Inc.
Product Name: G1S
Version: 1.0
Wake-up Type: Power Switch
SKU Number:
Family:
Signed-off-by: Jory A. Pratt <geekypenguin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Netbooks based on the Soltech TA12 do not send a key release
for volume keys causing Linux to think the key is constantly
being pressed forever.
Added quirk data for forced release keys.
BugLink: https://bugs.launchpad.net//bugs/397499
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 3d5cb60e ("Input: simplify name handling for certain input
handles") introduced a regression for the EVIOCGNAME/JSIOCGNAME
ioctl.
Before this, patch, the platform device's name was given back to
userspace which was good to identify devices. After this patch, the
device is ("event%d", minor) which is not descriptive at all.
This fixes the behaviour by taking dev->name.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reviewed-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables forced releasing of the Fn+Volume hotkeys
on the Fujitsu Siemens Amilo Pi 3525 notebook.
Signed-off-by: Simon Davie <nexx@nexxdesign.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Gets rid of the following warning:
Platform driver 'pcspkr' needs updating - please use dev_pm_ops
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds DMI information to automatically load the correct
layout for the Maxdata Pro 7000X/DX notebook models. Such notebooks
are clones of Fujitsu Amilo V2000, the hook for the v2000 is being
used and I have tested that perfectly works.
The immediate result of integrating this patch is that the five
special buttons will work on these specific notebook models and that
the RF killswitch will not be activated after suspend. This patch
definitively obsoletes the fsam7400 module which I was still needing
to enable wifi and to fix the RF killswitch suspend problem; in the
current 2.6.30 kernel it is necessary to load the wistron_btns module
with options 'force=1 keymap=1557/MS2141', which was not anyway a
complete workaround.
Signed-off-by: Giuseppe Mazzotta <g.mazzotta@iragan.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio_mouse - use standard driver registration method
Input: mark serio and i8042 as suspended when hibernating too
Input: add support for generic GPIO-based matrix keypad
Input: arrange keyboards alphabetically
Input: gpio-keys - avoid possibility of sleeping in timer function
Input: gpio-keys - revert 'change timer to workqueue'
Input: dm355evm_keys - fix kconfig symbol names
Input: wacom - add DTF720a support and fix rotation on Intuos3
Input: i8042 - more reset quirks for MSI Wind-clone netbooks
This patch is needed when the gpio's became available only at late
stages, for example, when using i2c gpio expander.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Serio ports are not being restarted any longer because resume operations
after hibernate do nothing, since the device has not been marked as
suspended. This happens because suspend is only considering the SUSPEND
event but not the FREEZE event.
Note that this driver has still to migrate to dev_pm_ops, but this fixes
this particular bug now.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Original patch by Marek Vasut, modified by Eric in:
1. use delayed work to simplify the debouncing
2. combine col_polarity/row_polarity into a single active_low field
3. use a generic bit array based XOR algorithm to detect key
press/release, which should make the column assertion time
shorter and code a bit cleaner
4. remove the ALT_FN handling, which is no way generic, the ALT_FN
key should be treated as no different from other keys, and
translation will be done by user space by commands like 'loadkeys'.
5. explicitly disable row IRQs and flush potential pending work,
and schedule an immediate scan after resuming as suggested
by Uli Luckas
6. incorporate review comments from many others
Patch tested on Littleton/PXA310 (though PXA310 has a dedicate keypad
controller, I have to configure those pins as generic GPIO to use this
driver, works quite well, though), and Sharp Zaurus model SL-C7x0
and SL-C1000.
[dtor@mail.ru: fix error unwinding path, support changing keymap
from userspace]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Reviewed-by: Uli Luckas <u.luckas@road.de>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_get_value function may sleep, so it should not be called in a
timer function. Move gpio_get_value calls to workqueue.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 0b346838c5.
This commit breaks GPIO debouncing by replacing the original mod_timer
with schedule_delayed_work in the interrupt handler. The latter does not
kick the timer further on GPIO line changes as it should to perform
debouncing.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When testing Moblin on various netbooks, we've got reports that
many MSI Wind clones need the i8042 reset quirks for the keyboard
and/or touchpad's proper function.
Signed-off-by: Yan Li <yan.i.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
This driver supports Synaptics I2C touchpad controller on eXeda
mobile device. Unfortunaltely it only works in relative mode and
thus is not comaptible with Xorg Synaptics driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics uses anisotropic coordinate system. On some wide touchpads
vertical resolution can be twice as high as horizontal which causes
unequal sensitivity on x/y directions. Add support for reading the
resolution with EVIOCGABS ioctl.
Signed-off-by: Tero Saarni <tero.saarni@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
PIT_TICK_RATE is currently defined in four architectures, but in three
different places. While linux/timex.h is not the perfect place for it, it
is still a reasonable replacement for those drivers that traditionally use
asm/timex.h to get CLOCK_TICK_RATE and expect it to be the PIT frequency.
Note that for Alpha, the actual value changed from 1193182UL to 1193180UL.
This is unlikely to make a difference, and probably can only improve
accuracy. There was a discussion on the correct value of CLOCK_TICK_RATE
a few years ago, after which every existing instance was getting changed
to 1193182. According to the specification, it should be
1193181.818181...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.osdl.org
Acked-by: Chris Wright <chrisw@sous-sol.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support to the input core to report the proper device name to
userspace for their devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When pressing any button belonging to the touchpoint, the generated
click events don't belong to the touchpoint but to the touchpad.
This patch fixes this behaviour, the events will be sent via the
correct device, so scrolling with touchpoint is possible.
Signed-off-by: Ulrich Dangel <uli@spamt.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The gpio_get_value function of I2C/SPI GPIO expander may sleep thus this
function call can not be called in a timer function.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some SoCs support only pin change interrupts on GPIO pins used as irq
lines.
The ads7846 core is not affected from the additional irqs on the rising
edge because the code accounts touch bounce anyway by kicking in a timer
and disabling the irq after the first request and reenabling the irq after
a timeout when there is no longer pen down detected.
Signed-off-by: Michael Roth <mroth@nessie.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The touchscreen works in two modes, wait trigger mode and auto-semi
mode. The device starts in wait trigger mode and waits until pressure
is detected, then device sets WT_INT bit and raises an interrupt.
The driver should put the device into auto-semi mode and prepare for
reading first X and then Y coordinates. When coordinate data is ready
the driver sets ADC_INT bit and raises interrupt again.
[dtor@mail.ru: various cleanups]
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The appletouch driver is prone to reporting multiple fingers when only
one is pressing. The appletouch driver queries an array of pressure
sensors and counts local maxima in pressure to determine the number of
fingers. It just does this on the raw values, so a data stream like:
0 100 250 300 299 300 250 100 0
actually registers as 2 fingers.
This patch updates the logic to ignore small dips in pressure that are
less than the threshold.
Signed-off-by: Jeremy Huddleston <jeremyhu@freedesktop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>