Commit graph

7498 commits

Author SHA1 Message Date
Patrick McHardy
6ed106549d net: use NETDEV_TX_OK instead of 0 in ndo_start_xmit() functions
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.

Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05 19:16:04 -07:00
Manu Abraham
eebf8d86ac V4L/DVB (12131): BUGFIX: An incorrect Carrier Recovery Loop optimization table was being
loaded for a given chip version. This would cause the optimization in
tuning not to be applied and thus a failed expectation, in tuning speed
increment. The patch swaps the tables in use. It also fixes a possible
one in a million condition where state->dev_ver implies an older Cut
(Cut < 2.0, eventhough the driver doesn't attach to any Cut older than
2.0) or even negative (due to a bad I2C bus master driver) for the card
combination.

Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing
out the issue at large.

Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:29:57 -03:00
Manu Abraham
0a5ded56fd V4L/DVB (12130): Fix a redundant compiler warning
drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_optimize_carloop_short’:
drivers/media/dvb/frontends/stv090x.c:2677: warning: ‘short_crl’ may be used uninitialized in this function

Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:29:50 -03:00
Trent Piepho
d8b2996607 V4L/DVB (12003): v4l2: Move bounding code outside I2C ifdef block
On Fri, 12 Jun 2009, Randy Dunlap wrote:
> From: Randy Dunlap <randy.dunlap@oracle.com>
>
> Move v4l_bound_align_image() outside of an #ifdef CONFIG_I2C block
> so that it is always built.  Fixes a build error:

clamp_align() should be moved as well, since it's only used by
v4l_bound_align_image().  I'm attaching an alternate version that fixes
this.  Labeled the endif too.

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:20 -03:00
Trent Piepho
1ca27379f3 V4L/DVB (11913): cx231xx: TRY_FMT should not actually set anything
In the TRY_FMT handler the function get_scale() is called to find what the
scaler hardware will produce for a requested size.

The problem is that get_scale(struct cx231xx *dev, ..., unsigned int *vscale,
unsigned int *hscale) saves the calculated scale values into both the
pointer arguments and into dev's hscale and vscale fields.  TRY_FMT shouldn't
actually change anything in the device state.

The code to in get_scale() that writes to dev->[hv]scale can just be
deleted.  In all cases when dev's fields should be modified, get_scale()
was called with get_scale(dev, ..., &dev->hscale, &dev->vscale), so dev was
getting updated anyway.

This didn't actually cause a problem because nothing ever actually made use
of the hscale and vscale fields.  I changed cx231xx_resolution_set() to use
those fields rather than re-calculate them with a call to get_scale().

Updating [hv]scale in cx231xx_resolution_set() isn't necessary because
every call of cx231xx_resolution_set() was already preceded by a call to
get_scale() or setting the [hv]scale fields, so they will be always be
up-to-date w.r.t. width and height.

Removing the call to get_scale() from cx231xx_resolution_set() allowed
making get_scale() a static function, which is a good thing for something
with such a short name.  There is already another function with the same
name in the em28xx driver, but that one is static.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:20 -03:00
Trent Piepho
ccb83408b2 V4L/DVB (11912): em28xx: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

It appears that the em2800 can only scale by 50% or 100%, i.e. the only
heights supported might be 240 and 480.  In that case the old code would
set any height other than 240 to 480.  Request 240 get 240, but request 239
and then you get 480.  Change it to round to the nearest supported value.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:19 -03:00
Trent Piepho
9bd0e8d7d1 V4L/DVB (11911): cx231xx: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:19 -03:00
Trent Piepho
653dc59b64 V4L/DVB (11910): mt9: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:19 -03:00
Trent Piepho
2449afcbcc V4L/DVB (11909): cx23885: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:19 -03:00
Trent Piepho
1c657a99fd V4L/DVB (11908): w8968cf: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

The existing code was casting pointers to u32 and to unsigned int into
pointers to u16.  This could mess up if someone passed in an image size
greater than 65,535 and on big-endian platforms it won't work at all.

The existing bounding code would shrink an image if it was too big, but
returned ERANGE if it was too small.  The code will not shrink or expand as
necessary.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:19 -03:00
Trent Piepho
4b89945e59 V4L/DVB (11907): cx88: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:19 -03:00
Trent Piepho
bc52d6eb44 V4L/DVB (11906): saa7134: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:18 -03:00
Trent Piepho
3adbbb8e2a V4L/DVB (11905): vivi: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:18 -03:00
Trent Piepho
728f5b93f4 V4L/DVB (11904): zoran: Use v4l bounding/alignment functiob
The v4l function has a better algorithm for aligning image size.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:18 -03:00
Trent Piepho
bc44fc061e V4L/DVB (11903): sh_mobile_ceu_camera: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:18 -03:00
Trent Piepho
4a6b8df213 V4L/DVB (11902): pxa-camera: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.

For instance the old code would change 159x243 into 156x240 to meet the
alignment requirements.  The new function will use 160x243, which is a lot
closer to what was asked for originally.

Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:18 -03:00
Trent Piepho
b0d3159be9 V4L/DVB (11901): v4l2: Create helper function for bounding and aligning images
Most hardware has limits on minimum and maximum image dimensions and also
requirements about alignment.  For example, image width must be even or a
multiple of four.  Some hardware has requirements that the total image size
(width * height) be a multiple of some power of two.

v4l_bound_align_image() will enforce min and max width and height, power of
two alignment on width and height, and power of two alignment on total
image size.

It uses an efficient algorithm that will try to find the "closest" image
size that meets the requirements.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:21:18 -03:00
Hans Verkuil
f0222c7d86 V4L/DVB (12125): v4l2: add new s_config subdev ops and v4l2_i2c_new_subdev_cfg/board calls
Add a new s_config core ops call: this is called with the irq and platform
data to be used to initialize the subdev.

Added new v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev_board calls
that allows you to pass these new arguments.

The existing v4l2_i2c_new_subdev functions were modified to also call
s_config.

In the future the existing v4l2_i2c_new_subdev functions will be replaced
by a single v4l2_i2c_new_subdev function similar to v4l2_i2c_new_subdev_cfg
but without the irq and platform_data arguments.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:15:47 -03:00
Mike Isely
90135c9686 V4L/DVB (12122): pvrusb2: De-obfuscate code which handles routing schemes
This change does not change any outward behavior; it merely chops down
some large if-conditions with embedded assignments into something a
little more maintainable for others (I of course never had a problem
with this...).

Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:15:17 -03:00
Mike Isely
81e804c9c2 V4L/DVB (12121): pvrusb2: Improve handling of routing schemes
The pvrusb2 driver has a concept of "routing scheme" which defines
which physical inputs should be connected based on application's
choice of logical input.  The correct "routing scheme" depends on the
specific device since different devices might wire up their muxes

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:15:13 -03:00
Mike Isely
6f441ed78e V4L/DVB (12120): pvrusb2: Change initial default frequency setting
Change default frequency to be US Broadcast channel 3 - with the
transition to d igital the previous value has now become useless.
This change is PURELY to help with my testing (I need to set some kind
of default so it might as well be some thing usable).

Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:15:09 -03:00
Mike Isely
a6862da2f3 V4L/DVB (12119): pvrusb2: Re-fix hardware scaling on video standard change
The cx25840 module's VBI initialization logic uses the current video
standard as part of its internal algorithm.  This therefore means that
we probably need to make sure that the correct video standard has been
set before initializing VBI.  (Normally we would not care about VBI,
but as described in an earlier changeset, VBI must be initialized
correctly on the cx25840 in order for the chip's hardware scaler to
operate correctly.)

It's kind of messy to force the video standard to be set before
initializing VBI (mainly because we can't know what the app really
wants that early in the initialization process).  So this patch does
the next best thing: VBI is re-initialized after any point where the
video standard has been set.

Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:15:05 -03:00
Mike Isely
e17d787c51 V4L/DVB (12118): pvrusb2: Fix hardware scaling when used with cx25840
The cx25840 module requires that its VBI initialization entry point be
called in order for hardware-scaled video capture to work properly -
even if we don't care about VBI.  Making this behavior even more
subtle is that if the capture resolution is set to 720x480 - which is
the default that the pvrusb2 driver sets up - then the cx25840
bypasses the hardware scaler.  Therefore this problem does not
manifest itself until some other resolution, e.g. 640x480, is tried.
MythTV typically defaults to 640x480 or 480x480, which means that
things break whenever the driver is used with MythTV.

This all has been known for a while (since at least Nov 2006), but
recent changes in the pvrusb2 driver (specifically in regards to
sub-device support) caused this to break again.  VBI initialization
must happen *after* the chip's firmware is loaded, not before.  With
this fix, 24xxx devices work correctly again.

A related fix that is part of this changeset is that now we
re-initialize VBI any time after we issue a reset to the cx25840
driver.  Issuing a chip reset erases the state that the VBI setup
previously did.  Until the HVR-1950 came along this subtlety went
unnoticed, because the pvrusb2 driver previously never issued such a
reset.  But with the HVR-1950 we have to do that reset in order to
correctly transition from digital back to analog mode - and since the
HVR-1950 always starts in digital mode (required for the DVB side to
initialize correctly) then this device has never had a chance to work
correctly in analog mode!  Analog capture on the HVR-1950 has been
broken this *ENTIRE* time.  I had missed it until now because I've
usually been testing at the default 720x480 resolution which does not
require scaling...  What fun.  By re-initializing VBI after a cx25840
chip reset, correct behavior is restored.

Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:15:01 -03:00
Michael Krufky
b34cdc36c4 V4L/DVB (12116): cx23885: ensure correct IF freq is used on HVR1200 & HVR1700
Ensure that we're programming the tda18271 tuner with the correct
IF frequencies to match the programming of the TDA10048 DVB-T demod
for the HVR1200 and HVR1700 products.

Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:58 -03:00
Michael Krufky
9d68fc0ad4 V4L/DVB (12115): tda10048: add missing entry to pll_tab for 3.8 MHz IF
Thanks for Terry Wu for pointing out the missing entry.

Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:56 -03:00
Hans Verkuil
aad40d3d0c V4L/DVB (12112): cx231xx: fix uninitialized variable.
The variable 'rc' could be used uninitialized in the cx231xx_capture_start
function. Sri informed me that it should be initialized to -1.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:52 -03:00
Hans Verkuil
54bb501c06 V4L/DVB (12111): tcm825x: remove incorrect __exit_p wrapper
tcm825x_remove is not necessarily called on module exit, it can also be
called when the i2c_adapter is removed. While the i2c adapter might never
be removed on an embedded system, in practice this sensor driver can also
be used in e.g. a USB webcam where this is a perfectly acceptable thing
to do.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:48 -03:00
Hans Verkuil
5543e2b4c4 V4L/DVB (12109): radio-tea5764: fix incorrect rxsubchans value
rxsubchans was only set when stereo was detected, otherwise it was
left to 0 instead of setting it to mono.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:43 -03:00
Hans Verkuil
be5daa9bd2 V4L/DVB (12107): smscoreapi: fix compile warning
gcc 4.3.1 generates this warning:

v4l/smscoreapi.c: In function 'smscore_gpio_configure':
v4l/smscoreapi.c:1481: warning: 'GroupNum' may be used uninitialized in this function
v4l/smscoreapi.c:1480: warning: 'TranslatedPinNum' may be used uninitialized in this function

While in practice this will not happen, it is something that the compiler
can't determine. Initializing these two local variables to 0 suppresses
this warning.

Cc: Udi Atar <udi.linuxtv@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:35 -03:00
Hans Verkuil
c6711c3e6d V4L/DVB (12104): ivtv/cx18: fix regression: class controls are no longer seen
A previous change (v4l2-common: remove v4l2_ctrl_query_fill_std) broke
the handling of class controls in VIDIOC_QUERYCTRL. The MPEG class control
was broken for all drivers that use the cx2341x module and the USER class
control was broken for ivtv and cx18.

This change adds back proper class control support.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:31 -03:00
Devin Heitmueller
a4c473033b V4L/DVB (12102): em28xx: add Remote control support for EVGA inDtube
Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:25 -03:00
Devin Heitmueller
19859229d7 V4L/DVB (12101): em28xx: add support for EVGA inDtube
Add support for the EVGA inDtube.  Both ATSC and analog side validated as
fully functional.

Thanks to Jake Crimmins from EVGA for providing the correct GPIO info.
Thanks to Alan Hagge for doing all the device testing.
Thanks to Greg Williamson for providing hardware for testing.

Cc: Jake Crimmins <jcrimmins@evga.com>
Cc: Alan Hagge <ahagge@gmail.com>
Cc: Greg Williamson <cheeseboy16@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:21 -03:00
Devin Heitmueller
cdf7bfa892 V4L/DVB (12100): em28xx: make sure the analog GPIOs are set if we used a card hint
In cases where the board had a default USB ID, we would not indentify the
board until after the call to em28xx_set_mode().  As a result, for those
boards the analog GPIOs were not being set before probing the i2c bus for
devices (the probe would occur with the GPIOs being all high).

Make a call to em28xx_set_mode() so that the GPIOs are set properly before
probing the i2c bus for devices.

This problem was detected with the EVGA inDtube, where the tvp5150 is not
powered on unless GPIO1 is pulled low.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:16 -03:00
Igor M. Liplianin
f867c3f4ea V4L/DVB (12098): Create table for customize stv0900 ts registers.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:12 -03:00
Abylay Ospan
ee1ebcfea6 V4L/DVB (12097): Implement reading uncorrected blocks for stv0900
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:07 -03:00
Abylay Ospan
68191edeb5 V4L/DVB (12096): Bug fix: stv0900 register read must using i2c in one transaction
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:14:03 -03:00
Igor M. Liplianin
0cde9b2533 V4L/DVB (12095): Change lnbh24 configure bits for NetUP card.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:59 -03:00
Hans de Goede
3fb4a57b49 V4L/DVB (12093): gspca_sonixj: Name saturation control saturation, not color
Name saturation control saturation, not color and make the default
less saturated (the old default was overdoing it).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:57 -03:00
Hans de Goede
f800952c21 V4L/DVB (12092): gspca_sonixj + ov7630: invert vflip control instead of changing default
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise
the picture is upside down. It is better to instead invert the meaning
of the control in the set function, and have the default be no vflip,
as one would expect vflip enabled to be upside down.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:54 -03:00
Hans de Goede
37c6dbe290 V4L/DVB (12091): gspca_sonixj: Add light frequency control
gspca_sonixj: Add light frequency control

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:49 -03:00
Hans de Goede
1fec747cd3 V4L/DVB (12090): gspca_sonixj: enable autogain control for the ov7620
gspca_sonixj: enable autogain control for the ov7620, and not only
make it enable autogain but also auto exposure (and do the
same for the ov7648).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:45 -03:00
Hans de Goede
a5d1cc39fe V4L/DVB (12089): gspca_sonixj: increase 640x480 frame-buffersize
gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer
overflows during my testing of a "Premier" 0c45:613e cam

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:38 -03:00
Hans de Goede
119893b2df V4L/DVB (12088): Mark the v4l1 uvcvideo quickcam messenger driver as deprecated
Mark the v4l1 uvcvideo quickcam messenger driver as deprecated, the one
cam it supports, is now also supported by the v4l2 gspca stv06xx driver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:33 -03:00
Hans de Goede
cc7b5b573f V4L/DVB (12087): gspca_sonixj: enable support for 0c45:613e camera
gspca_sonixj: enable support for 0c45:613e camera, and slightly tweak
the ov7630 register init values for a much better picture.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:29 -03:00
Hans de Goede
9764398bde V4L/DVB (12086): gspca_sonixj: Fix control index numbering
The control index defines for the gspca_sonixj driver were numbered
wrong, causing us to disable the wrong controls on various sensors

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:26 -03:00
Hans de Goede
e080fcd929 V4L/DVB (12085): gspca_ov519: constify ov518 inititial register value tables
gspca_ov519: constify ov518 inititial register value tables

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:22 -03:00
Hans de Goede
0220f8870e V4L/DVB (12084): ov511: mark as deprecated
Mark the v4l1 ov511 as deprecated as we now have ov511 support in
the gspca ov519 driver. Note we should really also keep track of this
in Documentation/feature-removal-schedule.txt, but that is not
part of the v4l-dvb tree.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:18 -03:00
Hans de Goede
98b1e9be88 V4L/DVB (12083): ov511: remove ov518 usb id's from the driver
ov511: remove ov518 usb id's from the driver, as they have not been working
ever since the decompression code got removed from the kernel, and they
are no supported by the gspca_ov519 module.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:16 -03:00
Hans de Goede
8668d504d7 V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor
Add support for st6422 bridge and sensor to the stv06xx gspca sub driver,
tested with:
Logitech QuickCam Messenger     046d:08f0       ST6422  integrated
Logitech QuickCam Mess. Plus    046d:08f6       ST6422  integrated

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:13:11 -03:00
Hans de Goede
ae49c40461 V4L/DVB (12081): gspca_ov519: Cleanup some sensor special cases
gspca_ov519: Cleanup some sensor special cases

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-06-23 03:12:50 -03:00