This patch adds the flags parameter to ipv6_find_hdr. This flags
allows us to:
* know if this is a fragment.
* stop at the AH header, so the information contained in that header
can be used for some specific packet handling.
This patch also adds the offset parameter for inspection of one
inner IPv6 header that is contained in error messages.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
During merge of net to net-next the changes in patch:
e1000e: Fix default interrupt throttle rate not set in NIC HW
got munged in param.c of the e1000e driver. This rectifies the
merge issues.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a new mesh configuration parameter "ht_opmode" and will
allow user to check the current HT protection mode selected. Users could
configure the protection mode by the command "iw mesh_iface set mesh_param
mesh_ht_protection_mode=2". The default protection mode of mesh is set to
non-HT mixed mode.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we have protection enabled, allow non-HT and HT20 stations to peer
with HT40+/- stations. Peering is still disallowed for HT40+/- mismatch.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Section 9.23.3.5 of IEEE 80211s standard describes the protection rules for
HT mesh STA in a MBSS. Three HT protection modes are supported for now:
non-HT mixed mode - is selected if any non-HT peers are present in our MBSS.
20MHz-protection mode - is selected if all peers in our 20/40MHz MBSS support
HT and atleast one HT20 peer is present.
no-protection mode - is selected otherwise.
This is a limited implementation of 9.23.3.5, which only considers mesh peers
when determining the HT protection mode. Station's channel_type needs to be
maintained.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the BSS table is organized in a RB tree, the BSSs need to be
comparable. This means that we must define a < and > operator to
the BSS object.
compare_ethr_addr isn't enough since it returns only a binary value.
Since Felix's
cfg80211: use compare_ether_addr on MAC addresses instead of memcmp
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSS table is corrupted: rb_find_bss can't find the bss.
As a result BSSes are duplicated in the BSS table, and we get stuck
while probing an AP before associating (in STA mode).
Change-Id: I85928756f4328028230832c1565ece7f412f3843
CC: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some sdio host controllers do not support real in band interrupt.
Software polling mode as a replacement is not fast enough for
high throughput and new features. Also some in band interrupts
do not support host wake up on embedded platform even when they
are real physical interrupts. Therefore out of band (oob)
interrupt mechanism is implemented for these scenarios.
To provide oob irq number and flags used for irq registration in
brcmfmac, a platform device contains irq resource must be
registered in board specific code.
Here is an example of platform device structure:
struct resource brcmf_sdio_res[] = {
{
.start = GPIO_BRCMF_SDIO_OOB_NUM,
.end = GPIO_BRCMF_SDIO_OOB_NUM,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
}
};
struct platform_device brcmf_sdio_device = {
.name = "brcmf_sdio_pd",
.id = -1,
.num_resources = ARRAY_SIZE(brcmf_sdio_res),
.resource = brcmf_sdio_res,
};
Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For out of band interrupt which is going to be introduced shortly,
the interrupt register function must be called after firmware is
downloaded. This patch moves it from brcmf_sdbrcm_probe to
brcmf_sdbrcm_bus_init.
Reviewed-by: pieter-paul giesberts <pieterpg@broadcom.com>
Reviewed-by: arend van spriel <arend@broadcom.com>
Signed-off-by: franky lin <frankyl@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bus state should be the correct flag for bus status. Use it instead
of result from previous function call for backplane clock switch.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sdbrcm_isr doesn't access to the dongle through SDIO bus.
Stop releasing and claiming host in irq handler to eliminate
any potential risk.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal and noise are forced to be positive since ethtool
deals in unsigned 64-bit values and this number should be human
readable. This gives easy access to some of the data formerly
exposed in the deprecated /proc/net/wireless file.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds hooks to call into the driver to get additional
stats for the ethtool API.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets ethtool print out stats related to stations
connected to the interface. Does not yet get stats
from the underlying driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device. The latter needs to be registered
first.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently cfg80211 fails to create a "phy80211" symlink in sysfs from
the net device to the wiphy device. The latter needs to be registered
first.
Compile-tested only.
Reported-by: Cesare Leonardi <celeonar@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFCSR is only used in rt2800. For other chipsets, the debug struct
for rfcsr should be zeroed, which isn't be an issue, since the code
can now cope with that.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow a register to be unspecified, therefore not creating its debugfs
file entry.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a mesh peer indicates it is operating as 20MHz-only in its HT
operation IE, have the rate control algorithm respect this by disabling
the equivalent bit in the ieee80211_sta HT capabilities.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need the station rate info when inserting a new sta_info. The
patch "mac80211: refactor mesh peer initialization" wrongly assumed the
rate info could be applied after insertion. After further review, this
is clearly not the case.
This fixes a regression where HT parameters were not applied before
inserting the sta_info, causing performance degradation.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"oui_type" in structure "ieee_types_vendor_header" is not used separately,
so include it in "oui" array. Now complete oui will be compared fixing
following warnings.
drivers/net/wireless/mwifiex/sta_ioctl.c:1410 mwifiex_set_gen_ie_helper()
error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/sta_ioctl.c:1435 mwifiex_set_gen_ie_helper()
error: memcmp() 'pvendor_ie->oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1177 mwifiex_update_bss_desc_with_ie()
error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
drivers/net/wireless/mwifiex/scan.c:1185 mwifiex_update_bss_desc_with_ie()
error: memcmp() 'vendor_ie->vend_hdr.oui' too small (3 vs 4)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate control updation never be called on 2040 BSS change.
The station should update its rate control on receiving beacon
with different HT mode in the HT operation IE. Not doing so,
leads to sending frames with higher(ht40) rates whereas AP is
operating in lower mode (ht20).
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a cut and paste mistake, sizeof(struct mib_local) was intended
instead of sizeof(struct mib_phy). The call to at76_get_mib() uses
sizeof(struct mib_local) correctly, although I changed that to
sizeof(*m) for style reasons after discussion with some of the wireless
maintainers.
The current code works fine because mib_phy structs are larger than
mib_local structs. But we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This doesn't make any sense. Init it from the transport instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are various problems happened on 5GHz band not observed on
2.4 GHz (microcode errors, queue stuck, etc... ) . Also roaming
between 5GHz AP and 2GHz does not work very well. To workaround
the problems add option to disable 5GHz support. This will help
on environments where APs are dual-band, and devices will not try
to associate on band where issues happen.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Also remove a debug print when allocation error occurred.
The kernel will complain anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When bluetooth coex is active and certain condition matched,
driver need to decide should the tx power been reduce or not.
Adding the logic to manage it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Do not assume we have our subsystem including this for us,
at least for older kernels this is not true. Lets just be
explicit about this requirement for the usage of wake_up().
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes ip_queue support which was marked as obsolete
years ago. The nfnetlink_queue modules provides more advanced
user-space packet queueing mechanism.
This patch also removes capability code included in SELinux that
refers to ip_queue. Otherwise, we break compilation.
Several warning has been sent regarding this to the mailing list
in the past month without anyone rising the hand to stop this
with some strong argument.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Explicit helper attachment via the CT target is broken with NAT
if non-standard ports are used. This problem was hidden behind
the automatic helper assignment routine. Thus, it becomes more
noticeable now that we can disable the automatic helper assignment
with Eric Leblond's:
9e8ac5a netfilter: nf_ct_helper: allow to disable automatic helper assignment
Basically, nf_conntrack_alter_reply asks for looking up the helper
up if NAT is enabled. Unfortunately, we don't have the conntrack
template at that point anymore.
Since we don't want to rely on the automatic helper assignment,
we can skip the second look-up and stick to the helper that was
attached by iptables. With the CT target, the user is in full
control of helper attachment, thus, the policy is to trust what
the user explicitly configures via iptables (no automatic magic
anymore).
Interestingly, this bug was hidden by the automatic helper look-up
code. But it can be easily trigger if you attach the helper in
a non-standard port, eg.
iptables -I PREROUTING -t raw -p tcp --dport 8888 \
-j CT --helper ftp
And you disabled the automatic helper assignment.
I added the IPS_HELPER_BIT that allows us to differenciate between
a helper that has been explicitly attached and those that have been
automatically assigned. I didn't come up with a better solution
(having backward compatibility in mind).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This refreshes the "timeout" attribute in existing expectations if one is
given.
The use case for this would be for userspace helpers to extend the lifetime
of the expectation when requested, as this is not possible right now
without deleting/recreating the expectation.
I use this specifically for forwarding DCERPC traffic through:
DCERPC has a port mapper daemon that chooses a (seemingly) random port for
future traffic to go to. We expect this traffic (with a reasonable
timeout), but sometimes the port mapper will tell the client to continue
using the same port. This allows us to extend the expectation accordingly.
Signed-off-by: Kelvie Wong <kelvie@ieee.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
To build ip_vs as a module sysctl_rmem_max and sysctl_wmem_max
needs to be exported.
The dependency was added by "ipvs: wakeup master thread" patch.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol '__ipvs_proto_data_get' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol 'ip_vs_ftp_init' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>