This patch (co-developed by Dan Williams and Holger Schurig) uses a kfifo
object for events and a swapping buffer scheme for the command response to
preserve the zero-copy semantics of the CF driver and keep memory usage low.
The main thread should only ever touch the buffer indexed by priv->resp_idx,
while the interface code is free to write to the second buffer, then swap
priv->resp_idx under the driver spinlock. The firmware specs only permit
one in-flight command, so there will only ever be one command response to
process at a time.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch tries to make dmesg logs between different runs easier
to compare by
* removing the jiffies (use CONFIG_PRINTK_TIME if you need
timing)
* remove the line numbers, they change with each applied patch
It also changes the deprecated __FUNCTION__ to __func__ to make
checkpatch.pl happy.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it a struct cmd_header, since that's what it is, and clean up
the places that it's used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need for these any more. We've collapsed all the unneeded nests of
functions which needed to keep track of which device the skb belonged to.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New typedefs are usually frowned upon. This patch changes
libertas_adapter -> struct libertas_adapter
libertas_priv -> struct libertas_priv
While passing, make everything checkpatch.pl-clean that gets touches.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies the namespace of variables, functions defines
and structures. It does:
- rename libertas_XXX to lbs_XXX
- rename LIBERTAS_XXX to lbs_XXX
- rename wlan_XXX to lbs_XXX
- rename WLAN_XXX to LBS_XXX (but only those that were
defined in libertas-local *.h files, e.g. not defines
from net/ieee80211.h)
While passing, I fixed some checkpatch.pl errors too.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when you define LBS_DEB_HEX, you get every hex dump in the
whole driver, e.g. for LBS_DEB_CMD, LBS_DEB_RX, LBS_DEB_TX etc. This
patch makes sure that you only get the hexdump that you're interested in.
Renamed lbs_dbg_hex() into lbs_deb_hex(), like the other lbs_deb_XXX()
macros.
Made lbs_deb_hex() issue a line feed (and a new prompt) after 16 bytes.
As lbs_deb_hex() now prints the ":" after the prompt by itself, removed
the misc colons in the various *.c files.
lbs_deb_XXX() now print the debug category as well.
As lbs_deb_XXX() --- and especially lbs_deb_11d() --- now print the
category, I removed various "11D:" prefixes in 11d.c as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is nowhere any place that set's this variable.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usually constants defined by #define are in ALL_UPPERCASE. This patch
fixes this.
I also shuffled the bits around so that they match the bit positions in the
host-interrupt-state register of the CF/SDIO card :-)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused/duplicated fields and consolidate static data rate arrays,
for example the libertas_supported_rates[] and datarates[] arrays in
the bss_descriptor structure, and the libertas_supported_rates field
in the wlan_adapter structure.
Introduce libertas_fw_index_to_data_rate and libertas_data_rate_to_fw_index
functions and use them everywhere firmware requires a rate index rather
than a rate array.
The firmware requires the 4 basic rates to have the MSB set, but most
other stuff doesn't, like WEXT and mesh ioctls. Therefore, only set the MSB
on basic rates when pushing rate arrays to firmware instead of doing a ton
of (rate & 0x7f) everywhere.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch, scanning with mshX interface will only return mesh networks. To
differentiate them, a specific mesh IE in beacons/probe responses is used. This
IE has been introduced in firmware release 5.110.14. Note:
Even though there can be at most a single mesh per channel, this scan might
return several networks in the same channel.
If all nodes in a mesh network are associated to an AP, they won't produce
beacons/probe responses, thus the network will not be listed. This will be fixed
in future firmware releases.
Scan on ethX interface is not filtered, so it will list both mesh and non-mesh
networks.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't touch hardware and therefore doesn't need endian notations
either.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- use a linked list for scan results
- age scan results
- pass bss_descriptors around instead of indexes into the scan table
- lock access to the scan results
- stop returning EAGAIN from SIOCGIWSCAN handler
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updated commands fwt_add and fwt_list, bt_list.
New commands: bt_get_invert, bt_set_invert, to invert the blinding table,
i.e., receive only frames from nodes listed in the BT.
This patch needs/is needed for firmware 5.220.9.p11.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For now, it's "libertas" by default, but that is overwritten in
if_usb.c/if_bootcmd.c and in if_cs.c.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This functions makes all libertas_sbi_XXX functions static to the
if_usb.c file and renames them to if_usb_XXXX(). The get called from
other places of the source code via priv->hw_XXXX().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It used to be LBS_DEB_MAIN, now it's LBS_DEB_THREAD
Also fixed a missing ":" in lbs_deb_enter()
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* renamed module parameter back to libertas_debug
* change from bit shifts to constants, that way it's easier to look at the
source and specify the libertas_debug=0xXXXX module parameter
* moved module_param from fw.c to main.c, where it belongs better
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug output of libertas was either not present or it was overwhelming.
This patch adds the possibility to specify a bitmask for the area of
interest. One should then only get the desired output.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move libertas_wlan_data_rates into wext.c and make it static. wext.c is the
only user of this array.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove filename from debug output because it's way too long.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also change WEPstatus to "wep_enabled"; it's clearer and consistent with the
WPAenabled and WPA2enabled members.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove WLAN_802_11_AUTHENTICATION_MODE enum and use IW_AUTH_ALG_* instead.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove setencryptionmode private ioctl and Encryptionmode variable.
Mostly unused, and its functionality is provided by other internal members
like WEPstatus, WPAenabled, WPA2enabled, and SIOCSIWGENIE.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obsoleted by SIOCSIWAUTH's IW_AUTH_80211_AUTH_ALG option introduced
by WE-18.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Useless; it set an internal variable that was unused anyway.
A supplicant handles all 802.1x authentication, not the driver.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the Marvell Libertas 8388 802.11 USB driver.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
