Intel IDE-R devices are part of the Intel AMT management setup. They don't
have any special configuration registers or settings so the ata_generic
driver will support them fully.
Rather than add a huge table of IDs for each chipset and keep sending in
new ones this patch autodetects them.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Until now identifying that a device supports WRITE SAME(16) with the
UNMAP bit set has been black magic. Implement support for the SBC-3
Thin Provisioning VPD page and set the TPWS bit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that libata provides proper cross-port EH exclusion. The SIDPR
locking added by commit 213373cf (ata_piix: fix locking around SIDPR
access) is no longer necessary. Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In libata, the non-EH code paths should always take and release
ap->lock explicitly when accessing hardware or shared data structures.
However, once EH is active, it's assumed that the port is owned by EH
and EH methods don't explicitly take ap->lock unless race from irq
handler or other code paths are expected. However, libata EH didn't
guarantee exclusion among EHs for ports of the same host. IOW,
multiple EHs may execute in parallel on multiple ports of the same
controller.
In many cases, especially in SATA, the ports are completely
independent of each other and this doesn't cause problems; however,
there are cases where different ports share the same resource, which
lead to obscure timing related bugs such as the one fixed by commit
213373cf (ata_piix: fix locking around SIDPR access).
This patch implements exclusion among EHs of the same host. When EH
begins, it acquires per-host EH ownership by calling ata_eh_acquire().
When EH finishes, the ownership is released by calling
ata_eh_release(). EH ownership is also released whenever the EH
thread goes to sleep from ata_msleep() or explicitly and reacquired
after waking up.
This ensures that while EH is actively accessing the hardware, it has
exclusive access to it while allowing EHs to interleave and progress
in parallel as they hit waiting stages, which dominate the time spent
in EH. This achieves cross-port EH exclusion without pervasive and
fragile changes while still allowing parallel EH for the most part.
This was first reported by yuanding02@gmail.com more than three years
ago in the following bugzilla. :-)
https://bugzilla.kernel.org/show_bug.cgi?id=8223
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reported-by: yuanding02@gmail.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration. These will be used to implement EH exclusion.
This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that DIPM can be used independently from HIPM, ata_piix can
support LPM too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Port multipliers can do DIPM on fan-out links fine. Implement support
for it. Tested w/ SIMG 57xx and marvell PMPs. Both the host and
fan-out links enter power save modes nicely.
SIMG 37xx and 47xx report link offline on SStatus causing EH to detach
the devices. Blacklisted.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current LPM implementation has the following issues.
* Operation order isn't well thought-out. e.g. HIPM should be
configured after IPM in SControl is properly configured. Not the
other way around.
* Suspend/resume paths call ata_lpm_enable/disable() which must only
be called from EH context directly. Also, ata_lpm_enable/disable()
were called whether LPM was in use or not.
* Implementation is per-port when it should be per-link. As a result,
it can't be used for controllers with slave links or PMP.
* LPM state isn't managed consistently. After a link reset for
whatever reason including suspend/resume the actual LPM state would
be reset leaving ap->lpm_policy inconsistent.
* Generic/driver-specific logic boundary isn't clear. Currently,
libahci has to mangle stuff which libata EH proper should be
handling. This makes the implementation unnecessarily complex and
fragile.
* Tied to ALPM. Doesn't consider DIPM only cases and doesn't check
whether the device allows HIPM.
* Error handling isn't implemented.
Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense. This patch reimplements
LPM support.
* The new implementation is per-link. The target policy is still
port-wide (ap->target_lpm_policy) but all the mechanisms and states
are per-link and integrate well with the rest of link abstraction
and can work with slave and PMP links.
* Core EH has proper control of LPM state. LPM state is reconfigured
when and only when reconfiguration is necessary. It makes sure that
LPM state is reset when probing for new device on the link.
Controller agnostic logic is now implemented in libata EH proper and
driver implementation only has to deal with controller specifics.
* Proper error handling. LPM config failure is attributed to the
device on the link and LPM is disabled for the link if it fails
repeatedly.
* ops->enable/disable_pm() are replaced with single ops->set_lpm()
which takes @policy and @hints. This simplifies driver specific
implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management is about to be reimplemented. Prepare for it.
* Implement sata_link_scr_lpm().
* Drop static from ata_dev_set_feature() and make it available to
other libata files.
* Trivial whitespace adjustments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm. This patch cleans up lpm related symbols
and sysfs show/store functions as follows.
* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
ATA_LPM_{MIN|MAX|MED}_POWER.
* Pre/postfixes are unified to lpm.
* sysfs show/store functions for link_power_management_policy were
curiously named get/put and unnecessarily complex. Renamed to
show/store and simplified.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This build error showed up in linux-next tag next-20100820 for ia64:
WARNING: vmlinux.o(.init.text+0x4a952): Section mismatch in reference from the function ata_init() to the function .exit.text:ata_sff_exit()
The function __init ata_init() references
a function __exit ata_sff_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
ata_sff_exit() so it may be used outside an exit section.
Sure enough, dropping the __exit fixes the problem.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This change enables my x86 machine to recognize and talk to a
"Native 4K" SATA device.
When I started working on this, I didn't know Matthew Wilcox had
posted a similar patch 2 years ago:
http://git.kernel.org/?p=linux/kernel/git/willy/ata.git;a=shortlog;h=refs/heads/ata-large-sectors
Gwendal Grignou pointed me at the the above code and small portions of
this patch include Matthew's work. That's why Mathew is first on the
"Signed-off-by:". I've NOT included his use of a bitmap to determine
512 vs Native for ATA command block size - just used a simple table.
And bugs are almost certainly mine.
Lastly, the patch has been tested with a native 4K 'Engineering
Sample' drive provided by Hitachi GST.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, sata_fsl, mv and nv call ata_qc_complete() multiple times
from their interrupt handlers to indicate completion of NCQ commands.
This limits the visibility the libata core layer has into how commands
are being executed and completed, which is necessary to support IRQ
expecting in generic way. libata already has an interface to complete
multiple commands at once - ata_qc_complete_multiple() which ahci and
sata_sil24 already use.
This patch updates the three drivers to use ata_qc_complete_multiple()
too and updates comments on ata_qc_complete[_multiple]() regarding
their usages with NCQ completions. This change not only provides
better visibility into command execution to the core layer but also
simplifies low level drivers.
* sata_fsl: It already builds done_mask. Conversion is straight
forward.
* sata_mv: mv_process_crpb_response() no longer checks for illegal
completions, it just returns whether the tag is completed or not.
mv_process_crpb_entries() builds done_mask from it and passes it to
ata_qc_complete_multiple() which will check for illegal completions.
* sata_nv adma: Similar to sata_mv. nv_adma_check_cpb() now just
returns the tag status and nv_adma_interrupt() builds done_mask from
it and passes it to ata_qc_complete_multiple().
* sata_nv swncq: It already builds done_mask. Drop unnecessary
illegal transition checks and call ata_qc_complete_multiple().
In the long run, it might be a good idea to make ata_qc_complete()
whine if called when multiple NCQ commands are in flight.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: O32 compat/N32: Fix to use compat syscall wrappers for AIO syscalls.
MAINTAINERS: Change list for ioc_serial to linux-serial.
SERIAL: ioc3_serial: Return -ENOMEM on memory allocation failure
MIPS: jz4740: Fix Kbuild Platform file.
MIPS: Repair Kbuild make clean breakage.
If the host is slow in reading data or doesn't read data at all,
blocking write calls not only blocked the program that called write()
but the entire guest itself.
To overcome this, let's not block till the host signals it has given
back the virtio ring element we passed it. Instead, send the buffer to
the host and return to userspace. This operation then becomes similar
to how non-blocking writes work, so let's use the existing code for this
path as well.
This code change also ensures blocking write calls do get blocked if
there's not enough room in the virtio ring as well as they don't return
-EAGAIN to userspace.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In this code, 0 is returned on memory allocation failure, even though other
failures return -ENOMEM or other similar values.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
expression x,e1,e2,e3;
@@
ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: Pat Gefre <pfg@sgi.com>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch reverts the driver to enabling/disabling the NFC interrupt
mask rather than enabling/disabling the system interrupt. This cleans
up the driver so that it doesn't rely on interrupts being disabled
within the interrupt handler.
For i.MX21 we keep the current behaviour, that is calling
enable_irq/disable_irq_nosync to enable/disable interrupts. This patch
is based on earlier work by John Ogness.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus/i2c/2636-rc8' of git://git.fluff.org/bjdooks/linux:
i2c-imx: do not allow interruptions when waiting for I2C to complete
i2c-davinci: Fix TX setup for more SoCs
448cd16 ("Input: evdev - rearrange ioctl handling") broke EVIOCSABS by
checking for the wrong direction bit.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The i2c_imx_trx_complete() function is using
wait_event_interruptible_timeout() to wait for the I2C controller to
signal that it has completed an I2C bus operation. If the process that
causes the I2C operation receives a signal, the wait will be
interrupted, returning an error. It is better to let the I2C operation
finished before handling the signal (i.e. returning into userspace).
It is safe to use wait_event_timeout() instead, because the timeout
will allow the process to exit if the I2C bus hangs. It's also better
to allow the I2C operation to finish, because unacknowledged I2C
operations can cause the I2C bus to hang.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch is an improvement to 4bba0fd8d1
which got to mainline a little early.
Sudhakar Rajashekhara explains that at least OMAP-L138 requires MDR mode
settings before DXR for correct behaviour, so load MDR first with
STT cleared and later load again with STT set.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fixes cursor corruption in certain cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Revert commit 54672386cc
"firewire: ohci: fix up configuration of TI chips".
It caused massive slow-down and data corruption with a TSB82AA2 based
StarTech EC1394B2 ExpressCard and FireWire 800 harddisks.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/657081http://thread.gmane.org/gmane.linux.kernel.firewire.user/4013
The fact that some card EEPROMs do not program these enhancements may be
related to TSB81BA3 phy chip errata, if not to bugs of TSB82AA2 itself.
We could re-add these configuration steps, but only conditional on a
whitelist of cards on which these enhancements bring a proven positive
effect.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org> 2.6.35
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The compat code for the VIDIOCSMICROCODE ioctl is totally buggered.
It's only used by the VIDEO_STRADIS driver, and that one is scheduled to
staging and eventually removed unless somebody steps up to maintain it
(at which point it should use request_firmware() rather than some magic
ioctl). So we'll get rid of it eventually.
But in the meantime, the compatibility ioctl code is broken, and this
tries to get it to at least limp along (even if Mauro suggested just
deleting it entirely, which may be the right thing to do - I don't think
the compatibility translation code has ever worked unless you were very
lucky).
Reported-by: Kees Cook <kees.cook@canonical.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix SDIO suspend/resume regression introduced by 4c2ef25fe0 "mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume":
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
pm_op(): platform_pm_suspend+0x0/0x5c returns -38
PM: Device pxa2xx-mci.0 failed to suspend: error -38
PM: Some devices failed to suspend
4c2ef25fe0 moved the card removal/insertion mechanism out of MMC's
suspend/resume path and into pm notifiers (mmc_pm_notify), and that
broke SDIO's expectation that mmc_suspend_host() will remove the card,
and squash the error, in case -ENOSYS is returned from the bus suspend
handler (mmc_sdio_suspend() in this case).
mmc_sdio_suspend() is using this whenever at least one of the card's SDIO
function drivers does not have suspend/resume handlers - in that case
it is agreed to force removal of the entire card.
This patch fixes this regression by trivially bringing back that part of
mmc_suspend_host(), which was removed by 4c2ef25fe0.
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: <stable@kernel.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add Cando touch screen 15.6-inch product id
HID: Add MULTI_INPUT quirk for turbox/mosart touchscreen
HID: hidraw, fix a NULL pointer dereference in hidraw_write
HID: hidraw, fix a NULL pointer dereference in hidraw_ioctl
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ehea: Fix a checksum issue on the receive path
net: allow FEC driver to use fixed PHY support
tg3: restore rx_dropped accounting
b44: fix carrier detection on bind
net: clear heap allocations for privileged ethtool actions
NET: wimax, fix use after free
ATM: iphase, remove sleep-inside-atomic
ATM: mpc, fix use after free
ATM: solos-pci, remove use after free
net/fec: carrier off initially to avoid root mount failure
r8169: use device model DMA API
r8169: allocate with GFP_KERNEL flag when able to sleep
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Silent spurious error message
drm/radeon/kms: fix bad cast/shift in evergreen.c
drm/radeon/kms: make TV/DFP table info less verbose
drm/radeon/kms: leave certain CP int bits enabled
drm/radeon/kms: avoid corner case issue with unmappable vram V2
Commit 0793448 "DMAENGINE: generic channel status v2" changed the interface for
how dma channel progress is retrieved. It inadvertently exported an internal
helper function ioat_tx_status() instead of ioat_dma_tx_status(). The latter
polls the hardware to get the latest completion state, while the helper just
evaluates the current state without touching hardware. The effect is that we
end up waiting for completion timeouts or descriptor allocation errors before
the completion state is updated.
iperf (before fix):
[SUM] 0.0-41.3 sec 364 MBytes 73.9 Mbits/sec
iperf (after fix):
[SUM] 0.0- 4.5 sec 499 MBytes 940 Mbits/sec
This is a regression starting with 2.6.35.
Cc: <stable@kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Richard Scobie <richard@sauce.co.nz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently we set all skbs with CHECKSUM_UNNECESSARY, even
those whose protocol we don't know. This patch just
add the CHECKSUM_COMPLETE tag for non TCP/UDP packets.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least one board using the FEC driver does not have a conventional
PHY attached to it, it is directly connected to a somewhat simple
ethernet switch (the board is the SnapGear/LITE, and the attached
4-port ethernet switch is a RealTek RTL8305). This switch does not
present the usual register interface of a PHY, it presents nothing.
So a PHY scan will find nothing - it finds ID's of 0 for each PHY
on the attached MII bus.
After the FEC driver was changed to use phylib for supporting PHYs
it no longer works on this particular board/switch setup.
Add code support to use a fixed phy if no PHY is found on the MII bus.
This is based on the way the cpmac.c driver solved this same problem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This add the product id of the touch screen found on ACER Aspire 5738PZ. Works
with hid-cando driver.
Signed-off-by: Francois Jaouen<francois.jaouen@laposte.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This should pass "buf" to bvec_kunmap_irq() instead of "bv". The api is
like kmap_atomic() instead of kmap().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
I see the following error message in my kernel log from time to time:
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
radeon 0000:07:00.0: ffff88007c334000 reserve failed for wait
After investigation, it turns out that there's nothing to be afraid of
and everything works as intended. So remove the spurious log message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make TV standard and DFP table revisions debug only.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These bits are used for internal communication and should
be left enabled. This may fix s/r issues on some systems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should not allocate any object into unmappable vram if we
have no means to access them which on all GPU means having the
CP running and on newer GPU having the blit utility working.
This patch limit the vram allocation to visible vram until
we have acceleration up and running.
Note that it's more than unlikely that we run into any issue
related to that as when acceleration is not woring userspace
should allocate any object in vram beside front buffer which
should fit in visible vram.
V2 use real_vram_size as mc_vram_size could be bigger than
the actual amount of vram
[airlied: fixup r700_cp_stop case]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This device generates ABS_Z and ABS_RX events, while it should be
generating ABS_X and ABS_Y instead. Using the MULTI_INPUT quirk solves
this issue.
Reference: https://bugs.launchpad.net/ubuntu/+bug/620609/
Signed-off-by: Pierre BAILLY <pierre@substantiel.fr>
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
commit 511d22247b (tg3: 64 bit stats on all arches), overlooked the
rx_dropped accounting.
We use a full "struct rtnl_link_stats64" to hold rx_dropped value, but
forgot to report it in tg3_get_stats64().
Use an "unsigned long" instead to shrink "struct tg3" by 176 bytes, and
report this value to stats readers.
Increment rx_dropped counter for oversized frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
