In ISDB-S, time-devision duplex is used to multiplexing several waves
in the same frequency. Each wave is identified by its own transport
stream ID, or TS ID. We need to provide some way to specify this ID
from user applications to handle ISDB-S frontends.
This code has been tested with the Earthsoft PT1 driver.
[mchehab@infradead.org: Fix merge conflicts with isdbt and rename the new parameter to DTV_ISDBS_TS_ID]
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was forgotten to map the LAYER_ENABLED ioctl to the frontend-cache and back.
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch increments the DVB-API to version 5.1 in order to reflect the addition of ISDB-T and ISDB-Tsb on Linux' DVB-API.
Changes in detail:
- added a small document to describe how to use the API to tune to an ISDB-T or ISDB-Tsb channel
- added necessary fields to dtv_frontend_cache
- added a smarter clear-cache function which resets all fields of the dtv_frontend_cache
- added a TRANSMISSION_MODE_4K to fe_transmit_mode_t
Signed-off-by: Olivier Grenie <olgrenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check the modulation in dvb_frontend_check_parameters against
frontend's capabilties for FE_QAM devices.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various frontend driver have parameter checks in their set_frontend
functions and return an error if the parameters are not supported,
tda10021 and cx24116 to name two.
The tuning ioctls FE_SET_FRONTEND/FE_SET_PROPERTY only change values
in the property cache and return before set_frontend is called. If a
set_frontend call in software zigzag algorithm fails and the card was
previously locked it will report a lock and the new parameters but is
still tuned to the old transport. This is not detectable from
userspace.
This change checks the return values of fe->ops.set_frontend and
changes the state to the added FESTATE_ERROR for software zigzag.
No lock will be reported to userspace if the State is FESTATE_ERROR.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fact that we now explicitly set fepriv->exit = 1 when the thread is
shutting down exposed an edge case where it was not being reset back to zero
once the thread went away in some cases. This resulted in failures in cases
where the frontend was closed, and then opened O_RDONLY, since in that case
the thread is not being restarted but it was checking the fepriv->exit flag.
Thanks to Thierry Lelegard, who and encountered and debugged a large portion
of the issue in the same twelve hours that I did (as well as testing my patch).
Cc: Thierry Lelegard <thierry.lelegard@tv-numeric.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A race condition was detected in the case that putting the tuner to sleep takes
an unusually long period of time, combined with applications that quickly
close/open the dvb frontend.
The kaffeine channel scanner closes and reopens the dvb frontend between each
tuning attempt. If it takes an unusually longer period of time to put the
tuner to sleep (for example, the Pinnacle 801e takes 660 ms), the dvb_frontend
thread will still be in a running state (and hence fepriv->thread is still set)
but the fepriv->exit field will still be zero. As a result, if a
dvb_frontend_start() call arrives while the frontend thread is in the process
of terminating, the call will return 0 without actually starting a new thread.
This results in the tuning request being dropped.
To address this, mark fepriv->exit as soon as we know the thread is going to
be terminated, so that dvb_frontend_start() knows to start a new instance.
Problem encountered with Kaffeine 0.8.7 doing ATSC scanning against the
Pinnacle 801e tuner, in conjunction with new code to power down the xc5000
when not in use.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For legacy applications stv0899 performs search only first time after insmod
due to not set DVBFE_ALGO_SEARCH_AGAIN bit
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/master/v4l/dvb_frontend.c:838:19: warning: symbol 'dtv_cmds' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1035:6: warning: symbol 'dtv_property_dump' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1066:5: warning: symbol 'is_legacy_delivery_system' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1080:6: warning: symbol 'dtv_property_cache_sync' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1132:6: warning: symbol 'dtv_property_legacy_params_sync' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1187:6: warning: symbol 'dtv_property_adv_params_sync' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1222:6: warning: symbol 'dtv_property_cache_submit' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1253:5: warning: symbol 'dtv_property_process_get' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1362:5: warning: symbol 'dtv_property_process_set' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It has been noticed that in HW tuning mode in cx24123.c that
a check is made to not alter the status var when in one shot
mode, a simpler solution is to not update here for all cards.
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Issue: Currently, the DVBFE_ALGO_CUSTOM is called only at the first tuning.
After the first call, the status is never set to force a new tuning.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not safe to assume that the i2c gate will be open before issuing the
command to power down the tuner. In fact, many demods only open the gate
long enough to issue the tuning command.
This fix allows power management to work properly for those tuners behind an
i2c gate (in my case the problem was with the HVR-950Q)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ATSC should be considered a legacy delivery system, or else fields such as
p->u.vsb.modulation do not get populated (resulting in set_frontend failures)
Cc: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rather than implementing different ways leading to confusion.
This allows multiple gate_enable/disable's in the tuner_read/write
functions, thereby lesser number of I/O operations throughout,
eventually leading to better results. As a side effect demods that
detect the STOP bit for auto closing of the gate can be avoided, thereby
a very minimal gain in disabling the auto detect feature as well.
Improves readability on the device control.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When moving from one frontend to another
an application could spawn multiple threads opening
the same new frontend and in some circumstances all of
these could become delayed waiting for the previous
frontend readers or previous frontend writer thread to
complete.
In this scenario the first thread will succeed on open
to bring the new frontend online but any others will return
EBUSY. This is a fault. If the first succeeds and all others
are on the same frontend then they should succeed also.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This add frontend R/W mutual exclusion.
Prior to this point in time it was possible to open both
frontends simultaneously which an MFE card cannot support.
In order to stop this, a delayed open is performed which
has the following function:
- Return EBUSY after a configurable amount of time
if a frontend is unavailable due to the other being
in use.
- Only allow opening of a frontend if the kernel thread
of the other has stopped.
This solution was chosen to allow switching between
frontends to work as seamlessly as possible. When both
frontends are actually opened simultaneously then one
will only open, but if quick switching is performed
between one of many then the new open will succeed in
a clean fashion rather than interrupting a kernel
thread.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A detailed description from the original patches 2 years ago:
"The WinTV-HVR3000 has a single transport bus which is shared between
a DVB-T and DVB-S modulator. These patches build on the bus acquisition
cx88 work from a few weeks ago to add support for this.
So to applications the HVR3000 looks like this:
/dev/dvb/adapter0/fe0 (cx24123 DVB-S demod)
/dev/dvb/adapter0/fe1 (cx22702 DVB-T demod)
Additional boards continue as before, eg:
/dev/dvb/adapter1/fe0 (lgdt3302 ATSC demod)
The basic change is removing the single instance of the videobuf_dvb in
cx8802_dev and saa7134_dev(?) and replacing it with a list and some
supporting functions.
*NOTE* This branch was taken before v4l-dvb was closed for 2.6.19 so
two or three current cx88 patches appear to be reversed by this tree,
this will be cleaned up in the near future. The patches missing change
the mutex handing to core->lock, fix an enumeration problem."
It should be recognised that a number of people have been maintaining
this patchset. Significant levels of Kudos to everyone one involved,
including but not limited to:
Darron Broad
Fabio M. Di Nitto
Carlo Scarfoglio
Hans Werner
Without the work of these people, and countless others, my two year old
patches would of died on the Mercurial linuxtv.org vine a long time
ago.
TODO: Revise these patches a little further so that the need for
demux1 and dvr0 is optional, not mandatory on the HVR3000.
HISTORY (darron):
This is the last update to MFE prepared by Hans which is based
upon the `scratchpad' diff created by Carlo.
All MFE work prior to that point must be attributed to Fabio
who ported and maintained Steve's original patch up to that
time.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A user tuning DVB-T via the S2API reports that this was not implemented,
and his tuning was failing.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuning DVB-T via the S2API was failing, missing some essential items.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reports from users that using the new API for tuning DTV was failing,
and the cache was missing some essential items.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
... and cleanup any drivers using them.
I've also removed NBC_QPSK and modified the cx24116 driver to check
the delivery_type also, removing some excess namespace baggage.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This means that when developers add new commands then they'll be see
the DTV_MAX_COMMAND define and will be more likely to modify it, without
having to modify the command validation code.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes switching from S2API to legacy where legacy params given to S2API
aware demods are cached ones and not those implied in the legacy API.
It was found (on an S2API aware demod at least) that after using
an S2API aware application and then switching to a legacy application
that prior S2API params were in effect were legacy has only
implied values. This fixes this.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Quick fix to stop an OOPS if illegal commands are dumped in S2API.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows application developers to query the dvb-core API version
dynamically, helping developers understand whether certain features
will be available.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows application developers to determine which particular
command in a sequence is invalid, or failing with error.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't want to push the ISDB-T definitions into the kernel until
we have a high level of confidence in the ISDB-T API. More testing
is required before this code is released.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many thanks to Darron Broad for pointing out the obvious.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also added some compat code for the older API.
Added more ISDB message/command suggestions, current not connected in dvb-core.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frontends will be notified (if they chose) of all _get and _set commands
so they can help determine result or action. Results are now returned
to userspace correctly.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The API now assumes that ioctl calls for FE_SET_PROPERTY and all
set commands, and FE_GET_PROPERTY are get commands.
Simplification.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This helps complex demods which support different modulation types
be better informed.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For demod drivers, we want a single tuning function (set_frontend) to have
access to the properly constructed dvb_frontend_parameters structure, or
the cache values - regardless of whether the legacy or new API is being used.
This cuts down on redundant code in the demod drivers and ensures the
tuning parameters are consistent regardless of the API entry type.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After discussion the following changes were made:
1. Removed the typedefs in frontend.h, use structures.
2. In the frontend.h, remove the 16 command limit on the API and
switch to a flexible variable length API. For practical reasons
a #define limits this to 64, this should be discussed.
3. Changed dvb-core ioctl handing to deal with variable sequences
of commands.
tune-v0.0.3.c is required to use this API, it contains the interface changes.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The group preferred dtv_ over tv_, this implements it.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Hans Werner for finding the problem.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SET_TONE and SET_VOLTAGE were not previously implemented. Two options
existed. Either cut/paste from the previous ioctl handler into the
process_properties function, which is code duplication. Or, split
the current ioctl handler into it's two major pieces.
Piece 1, responsible for input validation and semaphore acquiring
Piece 2 the processing of the previous ioctls
and finally, a new third pieces where the array of properties
is processed, and can freely call the legacy ioctl handler without
having to re-acquire the fepriv->sem semaphore. This is a clean approach
and ensures the existing legacy ioctls are processed as they were previously
(but with an extra function call) and allows the new API to share code
without duplication.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
