This patch adds driver for Sigmatek DVB-110 USB DVB-T stick. Stick has based
on hardware of Qtuantek QT1010 tuner, Zarlink ZL10353 (Intel CE 6353)
demodulator and Alcor Micro AU6610 DVB-T USB controller. HW is rather similar
as used in MSI Megasky GL861.
Currently, the driver works only in USB 2.0. In my understanding USB 1.1 is
also supported by hw but I cannot test it due to lack of USB 1.1 port. Device
supports only isochronous mode transfers. There is also eeprom in usb
controller(at least in address range 0x80 - 0xbf) for storing data, eg.
firmware. Anyway, firmware loading is not used / required by the device.
There seems to be at least one unknown I2C device in address 0xa0, probably
remote control or GPIO. Windows drivers reads registers from 0x00 to 0x07
from this unknown address.
Driver is based on gl861 module. Tuner has a lot of problems to lock with
megasky qt1010 module with this hardware with some broadcasting standards.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- use parallel_ts - Now this driver works.
- correct typo in MODULE_VERSION
Signed-off-by: Carl Lundqvist <comabug@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
remove unneeded declaration of .generic_bulk_ctrl_endpoint
generic_bulk_ctrl_endpoint isn't being used in this device, so this
is not needed here.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The megasky 580 based on gl861 has three endpoints:
- 0x81 BULK/ISOC IN MPEG2 TS
- 0x83 INT IN remote control receiver
- 0x02 BULK OUT bulk control endpoint
It doesn't look like the bulk endpoint is used, but better to
have the correct one in the config.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch moves the DVB_USB_IS_AN_I2C_ADAPTER flag from the adapter
properties to the device properties.
Without this patch I get an OOPS when the gl861 driver tries to
access any registers.
Signed-off-by: Jan Nijs <jan.nijs@scarlet.be>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The gl861_tuner_attach function is not specific to this device.
This patch removes gl861_tuner_attach, and replaces it with
qt1010_tuner_attach from the qt1010 header file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename driver_name from "gl861" to "dvb_usb_gl861"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The author's email address is already in the MODULE_AUTHOR field.
This patch adds his name as well.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for MSI Mega Sky 580 / GL861 DVB-T USB2.0
Except for the 2 lines added to zl10353.c, zl10353_reset_attach needs
to be changed. If I read the code correctly setting parallel_ts will
take care of the 3rd byte, but the 2nd byte needs to be 0x0b instead
of 0x03 too. I guess these changes needs to be done only for this
device, not sure how to do that.
The zl10353 changes have been split apart from this patch, into the next
patch, soon to follow.
Signed-off-by: Carl Lundqvist <comabug@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move filter caps from device caps to adapter caps for the megasky driver.
This fixes usb1.1 operation.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
QT1010:
- old qt1010-code totally rewritten and put in own kernel module
- same enhancements as my earlier QT1010 125kHz patch
- tuner initialization
- register 1f calculation
- register 20 calculation
- register 25 calculation
m920x: (MSI Megasky)
- use new QT1010 module instead of old code
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move .caps from the adapter properties to the device properties.
Thanks to Martin Schwier for confirming this fix.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The megasky_tuner_attach function is not specific to this device.
This patch renames it to qt1010_tuner_attach and moves it into the qt1010
header file.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cleanups and suggestions from Patrick Boettcher.
Dropped the mutex in m9206_rc_query using #if 0, because
M9206_CORE, M9206_I2C, M9206_FILTER and M9206_FW can be accessed
concurrently.
Thanks to both Aapo Tahkola and Patrick Boettcher.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- hardware pid filtering no longer enabled unless in usb 1.x mode
- more responsive rc handling
- some minor bug fixes and code refolding
- m9206_write delay dropped (doesn't seem to be needed)
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
qt1010 is a tuner used in some other devices, so this code should be put
into a separate file so that it could be reused by other drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
update code to use dvb_attach()
update code to reflect recent changes to the dvb_usb framework
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently, the driver works in bulk mode supporting both USB 2.0 and
1.0 with and without hardware pid filters.
The ULi m9205 also supports isochronous transfer mode, but I have
dropped support for it because it depends on firmware and does not work
on all USB host chips. Further, I have no firmware with remote
controller support for this mode.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Declare the parent device of i2c_adapter devices each time we can
easily do so. It makes the i2c_adapter appear at the right place in
the device tree, rather than as a platform device.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: v4l-dvb-maintainer@linuxtv.org
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
This patch removes unnecessary (and misleading) debug
output (it printed the values of the keys in the table up to the value
of the key pressed).
Signed-off-by: Mario Rossi <mariofutire@googlemail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Converted dee1601, lgz201 and dtt8579 to use dvb_pll_attach
in dvb-usb-cxusb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vendor IDs in this file were all in alphabetical
order except for this one.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding support for Pinnacle PCTV 400e DVB-S. The module name is called ttusb2,
because it this device (and other Pinnacle devices) is using the USB-protocol
originally used by Technotrend device. I'm suspecting Technotrend as the
device-designer.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also sprinkled some input_sync() throughout the code.
Acked-by: Ricardo Cerqueira <v4l@cerqueira.org>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch creates a new atsc tuner module for the LG TDVS-H06xF ATSC tuners,
called lgh06xf. The purpose of this change is to reduce some duplicated
code, and to allow the lgh06xf tuner code to take advantage of dvb_attach().
As a side effect, the dependency of dvb-bt8xx on dvb-pll has been removed,
since the lgh06xf module itself will use dvb-pll, while remaining optional
for the dvb-bt8xx driver through the use of DVB_FE_CUSTOMISE
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add alternative device ID (0xb808) for AverMedia AverTV Volar dongles.
Signed-off-by: Jose Carlos Garcia Sogo <jsogo@debian.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for Nova-T Stick with USB-pid: 0x7060
Signed-off-by: Stefan Traby <stefan@hello-penguin.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the new, STK7700-based revision
of the Leadtek Winfast DTV Dongle.
Signed-off-by: Michal CIJOML Semler <cijoml@volny.cz>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Forgot to increase the device count for the STK7700P-devices
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains support for the DiB7000PC-driver.
Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First working version of the dib7000m-driver.
This commit also makes the Hauppauge NOVA-T Stick working.
Signed-off-by: Francois Kanounnikoff <fkanounnikoff@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for more keys on the remote control included with the
DigitalNow tinyUSB2 DVB-T Receiver.
Signed-off-by: Luke Deller <luke@deller.id.au>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Antti Palosaari