Handle the error returned from snd_pcm_oss_get_formats() correctly
in SNDCTL_DSP_SETFMT ioctl handler of PCM OSS emulation.
Signed-off-by: Steven Finney <sfinney@healthhero.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] MAINTAINERS
[PARISC] Make ioremap default to _nocache
[PARISC] Add new entries to the syscall table
[PARISC] Further work for multiple page sizes
[PARISC] Fix up hil_kbd.c mismerge
[PARISC] defconfig updates
[PARISC] Document that we tolerate "Relaxed Ordering"
[PARISC] Misc. janitorial work
[PARISC] EISA regions must be mapped NO_CACHE
[PARISC] OSS ad1889: Match register names with ALSA driver
This fixes an oops in 2.6.16.X when loading the snd_powermac module. The
name of the requested module changed during the 2.6.16 development cycle
from i2c-keylargo to i2c-powermac.
Signed-off-by: Guido Guenther <agx@sigxcpu.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There was a report of a regression in the ALSA driver for the same
hardware.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update the schedule for the removal of drivers depending on
OBSOLETE_OSS_DRIVER as follows:
- adjust OBSOLETE_OSS_DRIVER dependencie
- from the release of 2.6.16 till the release of 2.6.17:
approx. two months for users to report problems with the ALSA
drivers for the same hardware
- after the release of 2.6.17 (and before 2.6.18):
remove the subset of drivers marked at OBSOLETE_OSS_DRIVER without
known regressions in the ALSA drivers for the same hardware
Additionally, correct some OBSOLETE_OSS_DRIVER dependencies.
A rationale of the changes is in
http://lkml.org/lkml/2006/1/28/135
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a hang in mpu401_uart.c that can occur when the mpu401 interface
is non-existent or otherwise doesn't respond to commands but we issue IO
anyway. snd_mpu401_uart_cmd now returns an error code that is passed up
the stack so that an open() will fail immediately in such cases.
Eventually discovered after wine/cxoffice would constantly cause hard
lockups on my desktop immediately after loading (emulating Windows too
well). Turned out that I'd recently moved my sound cards around and using
/dev/sequencer now talks to a sound card with a broken MPU.
This second version changes -EFAULT to -EIO and frees open resources on
error too. Test booted and seems to work ok.
Signed-off-by: Jon Masters <jcm@jonmasters.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unregister the platform device again if the probe was unsuccessful.
This restores the behaviour of not loading the driver on probe() failure.
Signed-off-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Continue with the next one on error from device registration.
This would seem the correct thing to do, even if it's not the probe()
error that we're getting.
Signed-off-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: PCM Midlevel
This patch makes the needlessly global snd_pcm_format_name() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: au88x0 driver
since idx is used as an index for vortex_pcm_prettyname[VORTEX_PCM_LAST],
it should not be equal to VORTEX_PCM_LAST. This fixes coverity bug id #572
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: au88x0 driver
Removed all use of __devinit/__devexit and init.h from headers. Any
attributes given in the prototype but not in the function definition have
been moved to the definition.
An exception is vortex_eq_free: I removed the __devexit attribute because
vortex_eq_free is called from vortex_core_shutdown, and
vortex_core_shutdown may be called from __devinit snd_vortex_create.
Compile tested with allyesconfig and allmodconfig.
Signed-off-by: Dale Sedivec <dale@codefu.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch adds the entry for the 5-stack pin-config for the STAC
chip on the Intel D945Pvs board with subdevice id 0x0707.
With this patch against 1.0.11rc4 in the linux kernel 2.6.17-rc1, I'm
able to successfully output over the optical port and analog ports.
Signed-off-by: Ashley Clark <aclark@ghoti.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This adds the support for HP Compaq Presario B2800 laptop with AD1986A codec.
Signed-off-by: Coywolf Qi Hunt <qiyong@freeforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA<-OSS emulation
Fix Oops due to a typo in snd_pcm_oss.c.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These are the last conversions of pci_set_dma_mask(),
pci_set_consistent_dma_mask() and pci_dma_supported() to use DMA_xBIT_MASK
constants from linux/dma-mapping.h
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (28 commits)
[ALSA] Kconfig SND_SEQUENCER_OSS help text fix
[ALSA] Add Aux input switch control for Aureon Universe
[ALSA] pcxhr - Fix the crash with REV01 board
[ALSA] sound/pci/hda: use create_singlethread_workqueue()
[ALSA] hda-intel - Add support of ATI SB600
[ALSA] cs4281 - Fix the check of timeout in probe
[ALSA] cs4281 - Fix the check of right channel
[ALSA] Test volume resolution of usb audio at initialization
[ALSA] maestro3.c: fix BUG, optimization
[ALSA] HDA/Realtek: multiple input mux definitions and pin mode additions
[ALSA] AdLib FM card driver
[ALSA] Fix / clean up PCM-OSS setup hooks
[ALSA] Clean up PCM codes (take 2)
[ALSA] Tiny clean up of PCM codes
[ALSA] ISA drivers bailing on first !enable[i]
[ALSA] Remove obsolete kfree_nocheck call
[ALSA] Remove obsolete kfree_nocheck call
[ALSA] Add snd-als300 driver for Avance Logic ALS300/ALS300+ soundcards
[ALSA] Add snd-riptide driver for Conexant Riptide chip
[ALSA] hda-codec - Fix noisy output wtih AD1986A 3stack model
...
Fix misleading help text for SND_SEQUENCER_OSS config option.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a mixer control which allows the user to switch the Aux
playback between the internal Aux jack, Wavetable, and Rear Line-In on
Aureon Universe cards.
For switching, a PCA9554 (8-line GPIO with I2C interface) and a 74HC4052
(dual 4-way mux/demux) are used. Output 0 and 1 of the PCA9554 are
connected to the select pins of the 74HC4052. The I2C interface of the
PCA9554 is connected to the card's internal SPI bus which is also used
to control the WM8770 and CS8415. SPI and I2C on the same lines...
To communicate with the PCA9554 the WM8770 and CS8415 are disabled and
an I2C Stop Condition is generated before the Start Condition (needed
for synchronisation because other SPI traffic appear to confuse the
PCA9554). Then a normal I2C data transfer takes place. Programming must
be done ridiculously slow; in theory, 4.7us is the minimum delay time
for normal-speed I2C according to the datasheet, but even with 10us
switching was unreliable. The Windows driver from Terratec does the
programming very slowly, too (checked with an oscilloscope).
PCA9554 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/PCA9554_9554A_6.pdf
74HC4052 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/74HC_HCT4052_4.pdf
Signed-off-by: Maximilian Rehkopf <otakon@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a new board revision for pcxhr boards, the
PCXHR_CHIPSC_GPI_USERI bit is no more supported.
The cards concerned have a REV01 in their PCI ID.
As the current driver tests this bit and does not load the
first Xilinx binary when it's 1, the card will crash on Xilinx
access over PCI. (the PCI will freeze ....)
The fix (fix to version 1.0.11rc4) works for both REV00 and
REV01 cards.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
process_unsol_events() seems to assume a singlethread one (IOW, racey).
So, this patch uses create_singlethread_workqueue() instead of
create_workqueue().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for high definition audio on ATI SB600.
Signed-off-by: Felix Kuehling <fkuehlin@ati.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Test the volume of usb audio whether actually it works and adjusts
the resolution value according to it.
Some USB audio devices report a lower resolution than it reacts.
The only possible check is to write and read a volume value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- fix brown-paper-bag locking bug (lock() / return / unlock())
- improve central function snd_m3_update_ptr()
(avoid expensive integer divisions)
- add cpu_relax() to busy-wait I/O loop as recommended
(does this require special macro support in ALSA for older kernels??)
- constify several structs
- spelling updates
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The following patch relative to CVS from 20060324 adds the following
features to the Realtek HDA codec.
1) Define two new pin modes: ALC_PIN_DIR_IN_NOMICBIAS and
ALC_PIN_DIR_INOUT_NOMICBIAS. These can be used with jack mode switch
definitions in mixers to prevent the user being offered the mic bias
options if the hardware doesn't support it.
2) Add the ability to have different input mux definitions for different
ADCs. This is needed because the ALC260 chip uses different mux layouts
for the two onboard ADCs. A new field (num_mux_defs) was added to the
alc_spec and alc_config_preset structures to support this.
3) Adjust numerous comments to make them consistent with the above changes.
4) Utilise the new multi-mux definition functionality for the ALC260 fujitsu
model to allow recording of the mixer output.
5) Utilise the new multi-mux definition functionality for the ALC260 test
model to make the mux selections a little less confusing.
6) Allow the headphone jack of the ALC260 acer model to be retasked in
the mixer.
6) Utilise the new multi-mux definition functionality for the ALC260 acer
model to give access to the mixer output and the retasked headphone
jack.
At this stage the *_NOMICBIAS modes are not used. We have reports that the
"Line" jack of at least some Acer models doesn't pass the bias out, and we
also know that NIDs 0x0f and 0x10 don't seem to accept the mic bias requests
at all. However, I feel we need to collect more evidence on both counts
before committing to the use of *_NOMICBIAS. In the case of the Acers, it's
not clear whether this issue (probably caused by the inclusion of DC
blocking capacitors) affects all Acer models or just a small number. With
the issue with NIDs 0x0f and 0x10 it's unclear whether this is a hardware
bug which will be addressed in later chip revisions or if it's an
intentional restriction. The datasheet makes no mention of the restriction
so at this stage I'm inclined to consider it a hardware bug. Comments in
the source reflect this reasoning.
On a similar theme, the headphone jack of the Fujitsu S7020 also doesn't
appear to pass mic bias voltage. I'm still investigating this however.
With the ability to retask the headphone jack, owners of ALC260-based Acer
laptops should now be able to record 4 channels of audio if they desire. The
multiple mux definitions allow this jack to be presented from both ADCs
(since this mux input is one of those which differs between the muxes).
This patch has been tested on a Fujitsu S7020 laptop and appears to behave
itself both for the "test" and "fujitsu" models. Definitions using only a
single mux specification also work. Other ALC chips should be fine but I
cannot test these myself. The "auto" modes should also continue to function
but again I have not verified this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Attached you'll find an ALSA driver for AdLib FM cards. An AdLib card is
just an OPL2, which was already supported by sound/drivers/opl3, so only
very minimal bus-glue is needed. The patch applies cleanly to both
2.6.16 and 2.6.16-mm1.
The driver has been tested with an actual ancient 8-bit ISA AdLib card
and works fine. It also works fine for an OPL3 {,emulation} as still
found on many ISA soundcards but given that AdLib cards don't have their
own mixer, upping the volume from 0 might be a problem without the card
driver already loaded and driving the OPL3.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Fix possible race of referring the setup hook from the running PCM
- Fix memory leak in an error path of proc write
- Clean up the setup hook parser
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Clean up initialization and destruction of substream instance
Now snd_pcm_open_substream() alone does most initialization jobs.
Add pcm_release callback for cleaning up at snd_pcm_release_substream()
- Tidy up PCM oss code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removed from CONFIG_EXPERIMENTAL from CONFIG_SND_CS46XX_NEW_DSP, and
make default to yes. This option works fine for years.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I have just discovered I made an error in the register value set in 'Limit
dmx6fire to 6 dacs' patch (bug1472). The value set should be '2a' not '0a'
as in the original patch, which unintentionally disables the 2nd MPU 401
UART.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Steven Finney