We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This improves the IGD/DIS picking using firstly if Intel, then
if the bus is bus 0. There may be a correct way to do this, but
I've no idea what it is.
Signed-off-by: Dave Airlie <airlied@redhat.com>
As we have already detected something attached to the chip during
initialisation, always report the LVDS connector status as connected
during probing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The IPS driver is designed to be able to run detached from i915 and
just not enable GPU turbo in that case, in order to avoid module
dependencies between the two drivers. This means that we don't know
what the load order between the two is going to be, and we had
previously only supported IPS after (optionally) i915, but not i915
after IPS. If the wrong order was chosen, you'd get no GPU turbo, and
something like half the possible graphics performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
It's required by the specs, but we don't know why. Let's not find out
why.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'intel/drm-intel-next' of /ssd/git/drm-next: (771 commits)
drm/i915: Undo "Uncouple render/power ctx before suspending"
drm/i915: Allow the application to choose the constant addressing mode
drm/i915: dynamic render p-state support for Sandy Bridge
drm/i915: Enable EI mode for RCx decision making on Sandybridge
drm/i915/sdvo: Border and stall select became test bits in gen5
drm/i915: Add Guess-o-matic for pageflip timestamping.
drm/i915: Add support for precise vblank timestamping (v2)
drm/i915: Add frame buffer compression on Sandybridge
drm/i915: Add self-refresh support on Sandybridge
drm/i915: Wait for vblank before unpinning old fb
Revert "drm/i915: Avoid using PIPE_CONTROL on Ironlake"
drm/i915: Pass clock limits down to PLL matcher
drm/i915: Poll for seqno completion if IRQ is disabled
drm/i915/ringbuffer: Make IRQ refcnting atomic
agp/intel: Fix missed cached memory flags setting in i965_write_entry()
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
drm/i915: Enable RC6 autodownclocking on Sandybridge
drm/i915: Terminate the FORCE WAKE after we have finished reading
drm/i915/gtt: Clear the cachelines upon resume
drm/i915: Restore GTT mapping first upon resume
...
Blitting from vram to gart is problematic at the moment.
Use the CPU for now to avoid buffer corruption.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Always useful to know just which connector was polled and had its
status updated.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were using the lockup struct from the wrong union.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This block may contain various additional LCD info such
as physical size and a stored EDID.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some systems have the LCD width and height in mm available in the
LCD info table. Use this info if there is no EDID to provide it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch tries to make sure that the vbl.reply.sequence
vblank count for a queued or emitted vblank event always
corresponds to the true vblank count of queueing/emission, so
the ddx can rely on the returned target_msc for consistency
checks and implementation of swap_intervals in glXSwapBuffers().
Without this there is a small race-condition between the
userspace ddx queueing a vblank event and the vblank
counter incrementing before the event gets queued in
the kernel.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Kconfig says fbcon is required by drm_kms_helper. If radeon, fbcon,
and drm_kms_helper are all modules, radeon is auto loaded (by PCI id?),
drm_kms_helper is loaded because of the module dependency, but fbcon
isn't loaded leaving the console unusable. Since fbcon is required
and there isn't an explicit module dependency, request the module
to be loaded from drm_kms_helper.
Signed-off-by: David Fries <david@fries.net>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Readability cleanup and fix debugging output, no
functional change.
Reported-by: Frank Huang <FrankR.Huang@amd.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Works more like DCE4.0 despite what the docs say.
This fixes blank screen issues when changing crtc
routing due to incorrect crtc to dig mapping.
v2: only two DIGx blocks, routing is hardcoded
based on link.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
add to the 2.8 bump for pageflip
The purpose of these regs is to work around a TX hw bug in R520.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed. Re-program
the mode first, then reset the dpms state.
This fixes the infamous atombios timeouts on resume.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes module reloading and resume as the gfx block seems to
be left in a bad state in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only reset the grbm blocks, srbm tends to lock the GPU
if not done properly and in most cases is not necessary.
Also, no need to call asic init after reset the grbm blocks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For the fbdev api if the struct fb_var_screeninfo accel_flags field is set
to FB_ACCELF_TEXT then userland applications can not mmap the mmio region.
Since it is a bad idea for DRM drivers to expose the mmio region via the
fbdev layer we always set the accel_flags to prevent this. Please apply.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 541cc96691.
Wei Yonjun reported this caused a regression against Intel VGA hotplug
on his G33 hw.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Without this, we attempt the handover too late, the firmware fb
might be accessing the chip simultaneously to us re-initializing
various parts of it, which might frighten babies or cause all sort
of nasty psychologic trauma to kitten.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[danvet: add cc: stable, forward ported and compile-fixed for X86]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[airlied: move to even earlier in module load.]
Signed-off-by: Dave Airlie <airlied@redhat.com>
