We ran into an issue where it looks like we're not properly ignoring a
pci device with a non-good status property when we walk the device tree
and instanciate the Linux side PCI devices.
However, the EEH init code does look for the property and disables EEH
on these devices. This leaves us in an inconsistent where we are poking
at a supposedly bad piece of hardware and RTAS will block our config
cycles because EEH isn't enabled anyway.
Signed-of-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Switch to use the generic power management helpers.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Subrata Modak reported that building a CONFIG_RELOCATABLE kernel with
CONFIG_ISERIES enabled gives the following warnings:
WARNING: 4 bad relocations
c00000000007216e R_PPC64_ADDR16_HIGHEST __ksymtab+0x00000000009dcec8
c000000000072172 R_PPC64_ADDR16_HIGHER __ksymtab+0x00000000009dcec8
c00000000007217a R_PPC64_ADDR16_HI __ksymtab+0x00000000009dcec8
c00000000007217e R_PPC64_ADDR16_LO __ksymtab+0x00000000009dcec8
The reason is that decrementer_iSeries_masked is using
LOAD_REG_IMMEDIATE to get the address of a kernel symbol, which
creates relocations that aren't handled by the kernel relocator code.
Instead of reading the tb_ticks_per_jiffy variable, we can just set
the decrementer to its maximum value (0x7fffffff) and that will work
just as well. In fact timer_interrupt sets the decrementer to that
value initially anyway, and we are sure to get into timer_interrupt
once interrupts are reenabled because we store 1 to the decrementer
interrupt flag in the lppaca (LPPACADECRINT(r12) here).
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Configuring a powerpc 32 bit kernel for both SMP and SUSPEND turns on
CPU_HOTPLUG to enable disable_nonboot_cpus to be called by the common
suspend code. Previously the definition of cpu_die for ppc32 was in
the powermac platform code, causing it to be undefined if that platform
as not selected.
arch/powerpc/kernel/built-in.o: In function 'cpu_idle':
arch/powerpc/kernel/idle.c:98: undefined reference to 'cpu_die'
Move the code from setup_64 to smp.c and rename the power mac
versions to their specific names.
Note that this does not setup the cpu_die pointers in either
smp_ops (request a given cpu die) or ppc_md (make this cpu die),
for other platforms but there are generic versions in smp.c.
Reported-by: Matt Sealey <matt@genesi-usa.com>
Reported-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc strncmp implementation does not correctly handle a zero
length, despite the claim in 0119536cd3
(Add hand-coded assembly strcmp).
Additionally, all the length arguments are size_t, not int, so use
PPC_LCMPI and eq instead of cmpwi and le throughout.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There appear to be Pegasos systems which have the rtas-event-scan
RTAS tokens, but on which the event scan always fails. They also
have an event-scan-rate property containing 0, which means call
event scan 0 times per minute.
So interpret a scan rate of 0 to mean don't scan at all. This fixes
the problem on the Pegasos machines and makes sense as well.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we build with ftrace enabled its possible that loadcam_entry would
have used the stack pointer (even though the code doesn't need it). We
call loadcam_entry in __secondary_start before the stack is setup. To
ensure that loadcam_entry doesn't use the stack pointer the easiest
solution is to just have it in asm code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In CONFIG_PTE_64BIT the PTE format has unique permission bits for user
and supervisor execute. However on !CONFIG_PTE_64BIT we overload the
supervisor bit to imply user execute with _PAGE_USER set. This allows
us to use the same permission check mask for user or supervisor code on
!CONFIG_PTE_64BIT.
However, on CONFIG_PTE_64BIT we map _PAGE_EXEC to _PAGE_BAP_UX so we
need a different permission mask based on the fault coming from a kernel
address or user space.
Without unique permission masks we see issues like the following with
modules:
Unable to handle kernel paging request for instruction fetch
Faulting instruction address: 0xf938d040
Oops: Kernel access of bad area, sig: 11 [#1]
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A future version of the MPC8610 HPCD's ASoC DMA driver will probe on individual
DMA channel nodes, so the DMA controller nodes' compatible string must be listed
in mpc8610_ids[] for the probe to work.
Also remove the "gianfar" compatible from mpc8610_ids[], since there is no
gianfar (or any other networking device) on the 8610.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are two front-panel LEDs on MPC837xRDB and MPC8315RDB boards: PWR
and HDD. After adding appropriate nodes we can program these LEDs from
kernel and user space.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since USB2 is shared with local bus, either local bus or USB2
should be disabled. By default U-Boot enables local bus, so we
have to disable USB2, otherwise kernel hangs:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
<hangs here>
Note that U-Boot doesn't clear 'status' property when it enables
USB2, so we have to comment out the whole node.
To enable USB2, one can issue
'setenv hwconfig usb2:dr_mode=<host|peripheral>' command at the
U-Boot prompt.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for eTSEC 2.0 as found in P1020.
The changes include introduction of the group nodes for
the etsec nodes.
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Technically, whilst SEC v3.3 h/w honours the tls_ssl_stream descriptor
type, it lacks the ARC4 algorithm execution unit required to be able
to execute anything meaningful with it. Change the node to agree with
the documentation that declares that the sec3.3 really doesn't have such
a descriptor type.
Reported-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable the DEBUG_PER_CPU_MAPS option so we can look for problems with
cpumasks .
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert to the new cpumask API.
irq_choose_cpu can be simplified by using cpumask_next and cpumask_first.
smp_mpic_message_pass was doing open coded cpumask manipulation and passing an
int for a cpumask into mpic_send_ipi. Since mpic_send_ipi is only used
locally, make it static and convert it to take a cpumask. This allows us
to clean up the mess in smp_mpic_message_pass.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the *_map cpumask variants are deprecated, change the comments to
instead refer to *_mask.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert NUMA code to new cpumask API. We shift the node to cpumask
setup code until after we complete bootmem allocation so we can
dynamically allocate the cpumasks.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert hotplug-cpu code to new cpumask API.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dynamically allocate cpu_sibling_map and cpu_core_map cpumasks.
We don't need to set_cpu_online() the boot cpu in smp_prepare_boot_cpu,
init/main.c does it for us.
We also postpone setting of the boot cpu in cpu_sibling_map and cpu_core_map
until when the memory allocator is available (smp_prepare_cpus), similar
to x86.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask API in /proc/cpuinfo code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This separates the per cpu output from the summary output at the end of the
file, making it easier to convert to the new cpumask API in a subsequent
patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new cpumask API and add some comments to clarify how get_irq_server
works.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask functions in pseries SMP startup code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask functions in iseries SMP startup code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask_* functions, and dynamically allocate cpumask in fixup_irqs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new cpumask_* functions and dynamically allocate the cpumask in
smp_cpus_done.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use cpumask_first, cpumask_next in rtasd code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change &cpu_online_map to cpu_online_mask.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As explained in commit 1c0fe6e3bd, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.
Cc: linuxppc-dev@ozlabs.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to keep track of the backing pages that get allocated by
vmemmap_populate() so that when we use kdump, the dump-capture kernel knows
where these pages are.
We use a simple linked list of structures that contain the physical address
of the backing page and corresponding virtual address to track the backing
pages.
To save space, we just use a pointer to the next struct vmemmap_backing. We
can also do this because we never remove nodes. We call the pointer "list"
to be compatible with changes made to the crash utility.
vmemmap_populate() is called either at boot-time or on a memory hotplug
operation. We don't have to worry about the boot-time calls because they
will be inherently single-threaded, and for a memory hotplug operation
vmemmap_populate() is called through:
sparse_add_one_section()
|
V
kmalloc_section_memmap()
|
V
sparse_mem_map_populate()
|
V
vmemmap_populate()
and in sparse_add_one_section() we're protected by pgdat_resize_lock().
So, we don't need a spinlock to protect the vmemmap_list.
We allocate space for the vmemmap_backing structs by allocating whole pages
in vmemmap_list_alloc() and then handing out chunks of this to
vmemmap_list_populate().
This means that we waste at most just under one page, but this keeps the code
is simple.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the parsing of the device tree in
arch/powerpc/include/asm/parport.h assumes that the interrupt provided in
the parallel port node is a valid virtual irq. The values for the
interrupts provided in the device tree should have meaning in the context
of the driver for the specific interrupt controller to which the interrupt
is connected and irq_of_parse_and_map() should be used to determine the
correct virtual irq.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So we tried to speed things up a bit using flush_hash_pages() directly
but that falls over on 603 of course meaning we fail to flush the TLB
properly and we may even end up having it corrupt memory randomly by
accessing a hash table that doesn't exist.
This removes the "optimization" by always going through flush_tlb_page()
for now at least.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we always call start-cpu irrespective of if the CPU is
stopped or not. Unfortunatley on POWER7, firmware seems to not like
start-cpu being called when a cpu already been started. This was not
the case on POWER6 and earlier.
This patch checks to see if the CPU is stopped or not via an
query-cpu-stopped-state call, and only calls start-cpu on CPUs which
are stopped.
This fixes a bug with kexec on POWER7 on PHYP where only the primary
thread would make it to the second kernel.
Reported-by: Ankita Garg <ankita@linux.vnet.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves query_cpu_stopped() out of the hotplug cpu code and into
smp.c so it can called in other places and renames it to
smp_query_cpu_stopped().
It also cleans up the return values by adding some #defines
Cc: <stable@kernel.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
By setting "reset_type" to one of the following values, the default
software reset mechanism may be overidden. Here the possible values of
"reset_type":
1 - PPC4xx core reset
2 - PPC4xx chip reset
3 - PPC4xx system reset (default)
This will be used by a new PPC440SPe board port, which needs a "chip
reset" instead of the default "system reset" to be asserted.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A defconfig for the IBM ISS 476 simulator
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is a trivial 4xx plaform that uses the new simple bsp from
Josh and is handy to use in simulators such as ISS or even Mambo
who don't properly implement most of the actual devices in the
SoC but really only the core.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
476 requires an isync after loading MMU and debug related SPR's. Some of
these are in performance-critical paths and may need to be optimized, but
initially, we're playing it safe.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 47x core's MCSR varies from 44x, so it needs it's own machine check
handler.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds the base support for the 476 processor. The code was
primarily written by Ben Herrenschmidt and Torez Smith, but I've been
maintaining it for a while.
The goal is to have a single binary that will run on 44x and 47x, but
we still have some details to work out. The biggest is that the L1 cache
line size differs on the two platforms, but it's currently a compile-time
option.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 47x platform supports multiple cores and shares code with 44x.
Break out code that is common for initializing the primary and secondary
cpus into a function which can be called for both.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds a marker to the exception stack frame to aid in debugging.
It's already inserted on other platforms and xmon recognizes it and
identifies exception frames when showing stack traces.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
powernow-k8: Fix frequency reporting
x86: Fix parse_reservetop() build failure on certain configs
x86: Fix NULL pointer access in irq_force_complete_move() for Xen guests
x86: Fix 'reservetop=' functionality
The x86_64 call_rwsem_wait() treats the active state counter part of the
R/W semaphore state as being 16-bit when it's actually 32-bit (it's half
of the 64-bit state). It should do "decl %edx" not "decw %dx".
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With F10, model 10, all valid frequencies are in the ACPI _PST table.
Cc: <stable@kernel.org> # 33.x 32.x
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
LKML-Reference: <1270065406-1814-6-git-send-email-bp@amd64.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit e67a807 ("x86: Fix 'reservetop=' functionality") added a
fixup_early_ioremap() call to parse_reservetop() and declared it
in io.h.
But asm/io.h was only included indirectly - and on some configs
not at all, causing a build failure on those configs.
Cc: Liang Li <liang.li@windriver.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Wang Chen <wangchen@cn.fujitsu.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1272621711-8683-1-git-send-email-liang.li@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Upstream PV guests fail to boot because of a NULL pointer in
irq_force_complete_move(). It is possible that xen guests have
irq_desc->chip_data = NULL.
Test for NULL chip_data pointer before attempting to complete an irq move.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
LKML-Reference: <20100427152434.16193.49104.sendpatchset@prarit.bos.redhat.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org> [2.6.33]
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (27 commits)
MIPS: Loongson 2F: Fix of problems introduced by -mfix-loongson2f-jump
MIPS: Loongson-2F: Use CONFIG_CPU_JUMP_WORKAROUNDS to control workarounds.
MIPS: Loongson 2F: Enable fixups of the latest binutils
MIPS: Loongson: Add CPU_LOONGSON2F_WORKAROUNDS
MIPS: Kconfig: Make Broadcom SoC support naming consistent
MIPS: BCM63xx: Update defconfig
MIPS: oprofile: Fix breakage when CONFIG_OPROFILE=m
STAGING: octeon-ethernet: Use proper phy addresses for Movidis hardware.
NET: mdio-octeon: Enable the hardware before using it.
I2C: Fix section mismatch errors in i2c-octeon.c
MIPS: Loongson: Fix LOONGSON_ADDRWIN_CFG macro.
MIPS: Loongson: Fix phys_mem_access_prot() check
MIPS: Loongson: Fix find_vga_mem_init()
MIPS: Loongson: Fix typo in gdium mach type string.
MIPS: Use CKSEG1ADDR for uncached handler
MIPS: Check for accesses beyond the end of the PGD.
MIPS: Use uasm_i_ds{r,l}l_safe() instead of uasm_i_ds{r,l}l() in tlbex.c
MIPS: Add uasm_i_dsrl_safe() and uasm_i_dsll_safe() to uasm.
MIPS: die() does not call die notifier chain
MIPS: Swarm, Littlesur: Enable PATA platform driver.
...
