Commit graph

5282 commits

Author SHA1 Message Date
Vasu Dev
4bb6b51533 [SCSI] fcoe: reduces lock cost when adding a new skb to fcoe_pending_queue
Currently fcoe_pending_queue.lock held twice for every new skb
adding to this queue when already least one pkt is pending in this
queue and that is not uncommon once skb pkts starts getting queued
here upon fcoe_start_io => dev_queue_xmit failure.

This patch moves most fcoe_pending_queue logic to fcoe_check_wait_queue
function, this new logic grabs fcoe_pending_queue.lock only once to
add a new skb instead twice as used to be.

I think after this patch call flow around fcoe_check_wait_queue
calling in fcoe_xmit is bit simplified with modified
fcoe_check_wait_queue function taking care of adding and
removing pending skb in one function.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:29:13 -05:00
Steve Ma
30121d14f5 [SCSI] libfc: Check if exchange is completed when receiving a sequence
When a sequence is received in response to an exchange we issued previously,
we should check to see if the exchange has completed. If yes, the sequence
should be discarded. Since the exchange might be still in the completion
process, it should be untouched.

Signed-off-by: Steve Ma <steve.ma@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:29:11 -05:00
Mike Christie
d5e6054a0a [SCSI] libfc: use DID_ERROR when we have internall aborted command
If we aborted a command, because it timed out we should not use
DID_ABORT. It will fail the command right away back to the upper
layer. We want to use something that indicated that the problem
did not complete normally, but it was not a fatal problem.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:29:10 -05:00
Chris Leech
0f4915398a [SCSI] fcoe: use ETH_P_FIP for skb->protocol of FIP frames
FIP frames should leave the fcoe layer with skb->protocol set to
ETH_P_FIP, not ETH_P_802_3.

Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:29:08 -05:00
Joe Eykholt
5f48f70ece [SCSI] libfcoe: fip: fix non-FIP-mode FLOGI state after reset.
When a reset is sent using fcoeadm on a non-FIP mode NIC,
there's no link flap, so the fcoe_ctlr stays in non-FIP mode.

In that case, FIP wasn't setting the flogi_oxid or map_dest flag,
causing the FLOGI to be sent with the both wrong source MAC and
the wrong destination MAC address, causing it to fail.

This leads to a non-functioning HBA until a link flap or
instance delete/create.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:29:07 -05:00
Herbert Xu
f00a3328bf [SCSI] cxgb3i: Include net/dst.h for struct dst_cache
This driver needs dst_cache->dev so it should include net/dst.h
to ensure that it builds.  While net/tcp.h probably includes it
already, we shouldn't rely on that since there is no guarantee
that this won't change in future.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:09:33 -05:00
Brian King
cbbf58f2e2 [SCSI] ibmvfc: Driver version 1.0.6
Bump driver version

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:51 -05:00
Brian King
6d29cc56be [SCSI] ibmvfc: Improve LOGO/PRLO ELS handling
There are several scenarios where the ibmvfc driver needs to
try to log back into a target on the fabric. Today when these events
occur, we simply go through re-discovery for all attached targets,
assuming that either the query of the name server or an ADISC will
indicate we might need to log back into the target, which doesn't
work for all scenarios. Fix this by taking note of the affected target(s)
in these conditions and ensuring we try to PLOGI back into the target.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:49 -05:00
Brian King
5e47167b6b [SCSI] ibmvfc: Improve device rediscovery
For certain scenarios during device rediscovery, we detect we need
to log back into a target. Currently we do just that - PLOGI/PRLI
back into the target. Change the code to delete and add the target
from the FC transport layer as well, to ensure we handle any cases
where the target may have changed.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:47 -05:00
Brian King
497f9c504f [SCSI] ibmvfc: Add flush on halt support
The virtual I/O server controlling the NPIV adapter associated with
a virtual fibre channel adapter can send a HALT event to the client.
When this occurs, the client can no longer send commands until a RESUME
is received. By adding support for flush on halt, we will get all of
our outstanding commands flushed back before the Virtual I/O server
enters the halt state, eliminating potential command timeouts for
outstanding commands which might occur if we did not support this feature.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:45 -05:00
Brian King
79111d0899 [SCSI] ibmvfc: Add support for NPIV Logout
This patch adds support for a new command supported by the Virtual I/O
Server, NPIV Logout. The command will abort all outstanding commands
and log out of the fabric. Currently, the only way to do this is
by breaking the CRQ, which can take a fairly long time when lots of
commands are outstanding. The NPIV Logout commands provides a mechanism
to accomplish virtually the same function, but is much faster.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:44 -05:00
Brian King
43c8da907c [SCSI] ibmvfc: Fix deadlock in EH
Fixes the following deadlock scenario shown below. We currently allow
queuecommand to send commands when the ibmvfc workqueue is scanning for
new rports, so we should also allow EH to function at this time as well.

scsi_eh_3     D 0000000000000000 12304  1279      2
Call Trace:
[c0000002f7257730] [c0000002f72577e0] 0xc0000002f72577e0 (unreliable)
[c0000002f7257900] [c0000000000118f4] .__switch_to+0x158/0x1a0
[c0000002f72579a0] [c0000000004f8b40] .schedule+0x8d4/0x9dc
[c0000002f7257b60] [c0000000004f8f08] .schedule_timeout+0xa8/0xe8
[c0000002f7257c50] [d0000000001d23e0] .ibmvfc_wait_while_resetting+0xe4/0x140 [ibmvfc]
[c0000002f7257d20] [d0000000001d3984] .ibmvfc_eh_abort_handler+0x60/0xe4 [ibmvfc]
[c0000002f7257dc0] [d000000000366714] .scsi_error_handler+0x38c/0x674 [scsi_mod]
[c0000002f7257f00] [c0000000000a7470] .kthread+0x78/0xc4
[c0000002f7257f90] [c000000000029b8c] .kernel_thread+0x4c/0x68
ibmvfc_3      D 0000000000000000 12432  1280      2
Call Trace:
[c0000002f7253540] [c0000002f72535f0] 0xc0000002f72535f0 (unreliable)
[c0000002f7253710] [c0000000000118f4] .__switch_to+0x158/0x1a0
[c0000002f72537b0] [c0000000004f8b40] .schedule+0x8d4/0x9dc
[c0000002f7253970] [c0000000004f8e98] .schedule_timeout+0x38/0xe8
[c0000002f7253a60] [c0000000004f80cc] .wait_for_common+0x138/0x220
[c0000002f7253b40] [c0000000000a2784] .flush_cpu_workqueue+0xac/0xcc
[c0000002f7253c10] [c0000000000a2960] .flush_workqueue+0x58/0xa0
[c0000002f7253ca0] [d0000000000827fc] .fc_flush_work+0x4c/0x64 [scsi_transport_fc]
[c0000002f7253d20] [d000000000082db4] .fc_remote_port_add+0x48/0x6c4 [scsi_transport_fc]
[c0000002f7253dd0] [d0000000001d7d04] .ibmvfc_work+0x820/0xa7c [ibmvfc]
[c0000002f7253f00] [c0000000000a7470] .kthread+0x78/0xc4
[c0000002f7253f90] [c000000000029b8c] .kernel_thread+0x4c/0x68
fc_wq_3       D 0000000000000000 10720  1283      2
Call Trace:
[c0000002f559ac30] [c0000002f559ace0] 0xc0000002f559ace0 (unreliable)
[c0000002f559ae00] [c0000000000118f4] .__switch_to+0x158/0x1a0
[c0000002f559aea0] [c0000000004f8b40] .schedule+0x8d4/0x9dc
[c0000002f559b060] [c0000000004f8e98] .schedule_timeout+0x38/0xe8
[c0000002f559b150] [c0000000004f80cc] .wait_for_common+0x138/0x220
[c0000002f559b230] [c0000000002721c4] .blk_execute_rq+0xb4/0x100
[c0000002f559b360] [d00000000036a1f8] .scsi_execute+0x118/0x194 [scsi_mod]
[c0000002f559b420] [d00000000036a32c] .scsi_execute_req+0xb8/0x124 [scsi_mod]
[c0000002f559b500] [d0000000000c1330] .sd_sync_cache+0x8c/0x108 [sd_mod]
[c0000002f559b5e0] [d0000000000c15b4] .sd_shutdown+0x9c/0x158 [sd_mod]
[c0000002f559b660] [d0000000000c16d0] .sd_remove+0x60/0xb4 [sd_mod]
[c0000002f559b700] [c000000000392ecc] .__device_release_driver+0xd0/0x118
[c0000002f559b7a0] [c000000000393080] .device_release_driver+0x30/0x54
[c0000002f559b830] [c000000000392108] .bus_remove_device+0x128/0x16c
[c0000002f559b8d0] [c00000000038f94c] .device_del+0x158/0x234
[c0000002f559b960] [d00000000036f078] .__scsi_remove_device+0x5c/0xd4 [scsi_mod]
[c0000002f559b9f0] [d00000000036f124] .scsi_remove_device+0x34/0x58 [scsi_mod]
[c0000002f559ba80] [d00000000036f204] .__scsi_remove_target+0xb4/0x120 [scsi_mod]
[c0000002f559bb10] [d00000000036f338] .__remove_child+0x2c/0x44 [scsi_mod]
[c0000002f559bb90] [c00000000038f11c] .device_for_each_child+0x54/0xb4
[c0000002f559bc50] [d00000000036f2e0] .scsi_remove_target+0x70/0x9c [scsi_mod]
[c0000002f559bce0] [d000000000083454] .fc_starget_delete+0x24/0x3c [scsi_transport_fc]
[c0000002f559bd70] [c0000000000a2368] .run_workqueue+0x118/0x208
[c0000002f559be30] [c0000000000a2580] .worker_thread+0x128/0x154
[c0000002f559bf00] [c0000000000a7470] .kthread+0x78/0xc4
[c0000002f559bf90] [c000000000029b8c] .kernel_thread+0x4c/0x68

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:42 -05:00
Brian King
7d0e462247 [SCSI] ibmvfc: Reduce error logging noise
The ibmvfc driver currently logs errors during discovery for several
transient fabric errors, which generally get retried. If retries
do not work, we see multiple errors in the log. If retries do work,
we see errors in the log which may be confusing since the retry worked.
This patch enhances the discovery time error logging to only log errors
for command failures during discovery if all allowed retries have been
used up. The existing behavior of logging all failures can be restored
by setting the hosts log_level to a value of 3 or greater.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:34 -05:00
Brian King
85e2399e92 [SCSI] ibmvfc: Use DEVICE_ATTR macro
Use DEVICE_ATTR macro for defining device sysfs attributes.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:33 -05:00
Brian King
7270b9bde5 [SCSI] ibmvfc: Fixup GFP flags for target allocations
Since target allocations can occur while resetting the virtual adapter,
we shouldn't be using GFP_KERNEL for them as it could hang. Switch to
use GFP_NOIO.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:31 -05:00
Brian King
4a2837d4fc [SCSI] ibmvfc: Fix invalid error response handling
Fix an obvious bug in processing error responses for SCSI commands
which can result in successful responses being incorrectly returned
with DID_ERROR.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:07:29 -05:00
James Bottomley
601e763825 [SCSI] sd: fix bug in SCSI async probing
The async split up of probing in sd.c created a potential failure case where
something goes wrong with device_add(), but which we don't recover properly.
Since, in general, asynchronous error handling is hard, move the device_add()
into the asynchronous path (it should be fast) and make sure all the deferred
processing cannot fail.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 13:00:13 -05:00
James Bottomley
91bc31fb3b [SCSI] fix up scsi_eh_lock_door()
The Documentation is incorrect (we removed some functions referred to), and
none of the bug warnings now apply.  Additionally remove the spurious check on
the return from blk_get_request() which can't fail if __GFP_WAIT is passed in.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 12:47:40 -05:00
Bartlomiej Zolnierkiewicz
477e608c03 [SCSI] fix documentation for two functions
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 12:23:35 -05:00
James Smart
53331aa1c7 [SCSI] lpfc 8.3.2 : Update the lpfc driver version to 8.3.2
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 11:26:34 -05:00
James Smart
21e9a0a5fb [SCSI] lpfc 8.3.2 : Persistent Vport Support
Add support for persistent vport definitions at creation at boot time

Also includes a few misc fixes for:
- conversion to vpi name from vport slang name
- couple of small mailbox references
- some additional discovery mods

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 11:26:19 -05:00
James Smart
f4b4c68f74 [SCSI] lpfc 8.3.2 : Miscellaneous Changes
Miscellaneous Changes:
- Convert from SLI2_ACTIVE flag to more correct SLI_ACTIVE (generic) flag
- Reposition log verbose messaging definitions
- Update naming for vpi object name from vport slang name
- Handle deferred error attention condition
- Add 10G link support
- Small bug fixup

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 11:26:01 -05:00
James Smart
d8e93df13c [SCSI] lpfc 8.3.2 : Update of copyrights
Update of copyrights on modified files

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 11:25:43 -05:00
James Smart
6fb120a7ed [SCSI] lpfc 8.3.2 : Addition of SLI4 Interface - FCOE Discovery support
SLI4 supports both FC and FCOE, with some extended topology objects.
This patch adss support for the objects, and updates the disovery
engines for their use.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 11:25:24 -05:00
James Smart
04c6849684 [SCSI] lpfc 8.3.2 : Addition of SLI4 Interface - Mailbox handling
The mailbox commands themselves are the same, or very similar to
their SLI3 counterparts. This patch genericizes mailbox command
handling and adds support for the new SLI4 mailbox queue.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 11:24:50 -05:00
James Smart
4f774513f7 [SCSI] lpfc 8.3.2 : Addition of SLI4 Interface - Queues
Adds support for the new queues in the SLI-4 interface.  There are :
- Work Queues - host-to-adapter for fast-path traffic
- Mailbox Queues - host-to-adapter for control (slow-path)
- Buffer Queues - host-to-adapter for posting buffers for async receive
- Completion Queues - adapter-to-host for posting async events,
       completions for fast or slow patch work, receipt of async
       receive traffic
- Event Queues - tied to MSI-X vectors, binds completion queues with
       interrupts

These patches add the all the support code to tie into command submission
and response paths, updates the interrupt handling, etc.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 11:23:54 -05:00
James Smart
da0436e915 [SCSI] lpfc 8.3.2 : Addition of SLI4 Interface - Base Support
Adds new hardware and interface definitions.

Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 11:21:29 -05:00
James Smart
3772a99175 [SCSI] lpfc 8.3.2 : Reorganization for SLI4
Preps the organization of the driver so that the bottom half, which
interacts with the hardware, can share common code sequences for
attachment, detachment, initialization, teardown, etc with new hardware.

For very common code sections, which become specific to the interface
type, the driver uses an indirect function call. The function is set at
initialization. For less common sections, such as initialization, the
driver looks at the interface type and calls the routines relative to
the interface.

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-06-08 11:18:10 -05:00
Jiri Pirko
ccffad25b5 net: convert unicast addr list
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).

I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.

The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>

 drivers/net/bnx2.c               |   13 +--
 drivers/net/e1000/e1000_main.c   |   24 +++--
 drivers/net/ixgbe/ixgbe_common.c |   14 ++--
 drivers/net/ixgbe/ixgbe_common.h |    4 +-
 drivers/net/ixgbe/ixgbe_main.c   |    6 +-
 drivers/net/ixgbe/ixgbe_type.h   |    4 +-
 drivers/net/macvlan.c            |   11 +-
 drivers/net/mv643xx_eth.c        |   11 +-
 drivers/net/niu.c                |    7 +-
 drivers/net/virtio_net.c         |    7 +-
 drivers/s390/net/qeth_l2_main.c  |    6 +-
 drivers/scsi/fcoe/fcoe.c         |   16 ++--
 include/linux/netdevice.h        |   18 ++--
 net/8021q/vlan.c                 |    4 +-
 net/8021q/vlan_dev.c             |   10 +-
 net/core/dev.c                   |  195 +++++++++++++++++++++++++++-----------
 net/dsa/slave.c                  |   10 +-
 net/packet/af_packet.c           |    4 +-
 18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29 22:12:32 -07:00
Abhijeet Joglekar
a366695592 [SCSI] libfc,fcoe,fnic: Separate rport and lport max retry counts
This allows fnic to configure number of retries for lport and rport
separately.

Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:18 -05:00
Eric Moore
d17bf602fb [SCSI] mpt2sas: bump driver version to 01.100.03.00
Bump driver version.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:18 -05:00
Eric Moore
d5d135b3a7 [SCSI] mpt2sas: using the same naming convention for all static function
This fix's is for all local function so their name has the "_" preceeding
the module name, then function name.  Most the code is already is using this
naming convention.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:17 -05:00
Eric Moore
ddf59a35e9 [SCSI] mpt2sas: add query task support for MPT2COMMAND ioctl
This patch will find an active mid for a query_task request via the ioctl path.

This code is already there for task_abort, so this patch combining code using
the same fuction _ctl_set_task_mid(), previously _ctl_do_task_abort().

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:17 -05:00
Eric Moore
993e0da7b7 [SCSI] mpt2sas: LUN Reset Support
Adding new eh_target_reset_handler for target reset. Change the
eh_device_reset_handler so its sending
MPI2_SCSITASKMGMT_TASKTYPE_LOGICAL_UNIT_RESET, instead of
MPI2_SCSITASKMGMT_TASKTYPE_TARGET_RESET.  Add new function
_scsih_scsi_lookup_find_by_lun as a sanity check to insure I_T_L commands are
completed upon completing lun reset.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:17 -05:00
Eric Moore
3c621b3ee1 [SCSI] mpt2sas: T10 DIF Support
This add support for type 1 and 3 DIF support per the Oracle API.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:16 -05:00
Andy Yan
f9da3be5af [SCSI] mvsas: remove all the casts from void * or to void *
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:13 -05:00
Mike Christie
4421c9ebee [SCSI] libiscsi: add debug printks for iscsi command completion path
This patch just adds some debug statements for the abort
and completion paths.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:13 -05:00
Mike Christie
b3cd5050bf [SCSI] libiscsi: add task aborted state
If a task did not complete normally due to a TMF, libiscsi will
now complete the task with the state ISCSI_TASK_ABRT_TMF. Drivers
like bnx2i that need to free resources if a command did not complete normally
can then check the task state. If a driver does not need to send
a special command if we have dropped the session then they can check
for ISCSI_TASK_ABRT_SESS_RECOV.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:13 -05:00
Mike Christie
1336aed10b [SCSI] libiscsi: check if iscsi host has work queue before queueing work
Instead of having libiscsi check if the offload bit is set, have
it check if the lld created a work queue. I think this is more
clear.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:12 -05:00
Mike Christie
301e0f7e4d [SCSI] libiscsi: don't let io sit in queue when session has failed
If the session is failed, but we have not yet fully transitioned
to the recovery stage we were still queueuing IO. The idea is
that for some failures we can recvover at the command level
and still continue to execute other IO. Well, we never have
added the recovery within a command code, so queueing up IO here
just creates the possibility that it might time time out so
this just has us requeue the IO the scsi layer for now.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:12 -05:00
Mike Christie
3bbaaad95f [SCSI] libiscsi: handle cleanup task races
bnx2i needs to send a hardware specific cleanup command if
a command has not completed normally (iscsi/scsi response from
target), and the session is still ok (this is the case when we
send a TMF to stop the command).

At this time it will need to drop the session lock. The problem
with the current code is that fail_all_commands assumes we
will hold the lock the entire time, so it uses list_for_each_entry_safe.
If while bnx2i drops the session lock multiple cmds complete then
list_for_each_entry_safe will not handle this correctly.

This patch removes the running lists and just has us loop over
the cmds array (in later patches we will then replace that
array with a block tag map at the session level). It also fixes
up the completion path so that if the TMF code and the normal recv
path were completing the same command then they both do not try
to do release the refcount taken when the task is queued.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:12 -05:00
Mike Christie
4c48a82935 [SCSI] libiscsi: fix iscsi transport checks to account for slower links
If we have not got any pdus for recv_timeout seconds, then we will
send a iscsi ping/nop to make sure the target is still around. The
problem is if this is a slow link, and the ping got queued after
the data for a data_out (read), then the transport code could think
the ping has failed when it is just slowly making its way through
the network. This patch has us check if we are making progress while
the nop is outstanding. If we are still reading in data, then we
do not fail the session at that time.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:11 -05:00
Mike Christie
d1acfae514 [SCSI] libiscsi_tcp: update recv tracking for each skb instead of iscsi pdu
Everytime we read in a pdu libiscsi will update a tracking field.
It uses this to decide when to check if the transport might be bad.
If we have not got data in recv_timeout seconds then we will
send a iscsi ping/nop.

If we are on a slow link then it could take a while to read in all
the data for a data_in. In that case we might send a ping/nop when
we do not need to or we might drop a session thinking it is bad
when the lower layer is making forward progress on it.

This patch has libiscsi_tcp update the recv tracking for each skb
(basically network packet from our point of view) instead of the
entire iscsi pdu+data, so we account for these cases where data is
coming in slowly.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:11 -05:00
Mike Christie
26013ad4c4 [SCSI] libiscsi: fix nop response/reply and session cleanup race
If we are responding to a nop from the target by sending our nop,
and the session is getting torn down, then iscsi_start_session_recovery
could set the conn stop bits while the recv path is sending the nop
response and we will hit the bug ons in __iscsi_conn_send_pdu.

This has us check the state in __iscsi_conn_send_pdu and fail all
incoming mgmt IO if we are  not logged in and if the pdu is not login
related. It also changes the ordering of the setting of conn stop state
bits so they are set after the session state is set (both are set under
the session lock).

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:11 -05:00
Mike Christie
edbc9aa058 [SCSI] libiscsi: have iscsi_data_in_rsp call iscsi_update_cmdsn
This has iscsi_data_in_rsp call iscsi_update_cmdsn when a pdu is
completed like is done for other pdu's that are don.

For libiscsi_tcp, this means that it calls iscsi_update_cmdsn when
it is handling the pdu internally to only transfer data, but if there is
status then it does not need to call it since the completion handling
will do it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:10 -05:00
Mike Christie
8f9256cea1 [SCSI] libiscsi: export iscsi_itt_to_task for bnx2i
bnx2i needs to be able to look up mgmt task like login and nop, because
it does some processing of them on the completion path. This exports
iscsi_itt_to_task so it can look up the task.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:10 -05:00
Mike Christie
5700b1af93 [SCSI] libiscsi: handle param allocation failures
If we could not allocate the initiator name or some other id like
the hwaddress or netdev, then userspace could deal with the failure
by just running in a dregraded mode.

Now we want to be able to switch values for the params and we
want some feedback, so this patch will check if a string like
the initiatorname could not be allocated and return an error.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:10 -05:00
Mike Christie
184b57c630 [SCSI] libiscsi: check of LLD has a alloc pdu callout.
bnx2i does not have one. It currently preallocates the bdt
when the session is setup.

We probably want to change that to a dma pool, then allocate from
the pool in the alloc pdu. Until then check if there is a alloc
pdu callout.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:09 -05:00
Mike Christie
10eb0f013c [SCSI] iscsi: pass ep connect shost
When we create the tcp/ip connection by calling ep_connect, we currently
just go by the routing table info.

I think there are two problems with this.

1. Some drivers do not have access to a routing table. Some drivers like
qla4xxx do not even know about other ports.

2. If you have two initiator ports on the same subnet, the user may have
set things up so that session1 was supposed to be run through port1. and
session2 was supposed to be run through port2. It looks like we could
end with both sessions going through one of the ports.

Fixes for cxgb3i from Karen Xie.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:09 -05:00
Zhenwen Xu
5a2537959f [SCSI] NCR_D700: fix IRQ handler return type
drivers/scsi/NCR_D700.c: In function `NCR_D700_probe':
drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type
drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type
drivers/scsi/NCR_D700.c:322: warning: passing argument 2 of `request_irq' from incompatible pointer type

Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:09 -05:00
Andy Yan
9870d9a242 [SCSI] mvsas: performance improvement using domain_device->lldd_dev
Using sticky field to improve retrieve performance by eliminating some
lookups in . Remove some spurious casts.

Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:08 -05:00
Andy Yan
77db27cdcb [SCSI] mvsas: correct bit map usage
Utilize DECLARE_BITMAP to define the tags array.

Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:08 -05:00
Andy Yan
0f980a8716 [SCSI] mvsas: bug fix, null pointer may be used
Null pointer check to avoid corruption.

Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:08 -05:00
Andy Yan
0b84b7094e [SCSI] mvsas: bug fix of dead lock
TMF task should be issued with Interrupt Disabled, or Deadlock may take place.
Clean-up unused parameters and conditonal lock.

Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:07 -05:00
Andy Yan
2b288133ab [SCSI] mvsas: bug fix with setting task management frame type
Correct frame type setting according to parameter.

Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:07 -05:00
Kleber S. Souza
6ff63896e5 [SCSI] ipr: fix PCI permanent error handler
The ipr driver can hang if it encounters enough PCI errors
to trigger the permanent error handler. The driver will attempt
to initiate a "bringdown" of the adapter and fail all pending
ops back. However, this bringdown is unlike any other bringdown
of the adapter in the code as the driver. In this code path we
end up failing back ops with allow_cmds still set to 1. This results
in some commands, the HCAM commands in particular, getting immediately
re-issued to the adapter on the done call, which results in
an infinite loop in ipr_fail_all_ops. Fix this by setting allow_cmds
to zero in this path.

Signed-off-by: Kleber S. Souza <klebers@linux.vnet.ibm.com>
[brking@linux.vnet.ibm.com: alternate patch substituted]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:07 -05:00
Eric Piel
a3ec723a94 [SCSI] Update wording of CONFIG_SCSI_MULTI_LUN help
I had to set CONFIG_SCSI_MULTI_LUN to y in order to get my SE W595
working when plugging it as a mass storage. Looking at SCSI option to
get a phone behaving correctly was convoluted to say the least. There
are quite a few other reports about USB card readers needing this option
as well. This patch improves the help text to make the use of the option
more obvious.

Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:06 -05:00
Roel Kluin
16b3858ec9 [SCSI] ibmvscsi: Remove redundant test on unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:06 -05:00
Kai Makisara
1da2019fff [SCSI] st: fix gcc 4.4 warning
This patch fixes the GCC 4.4 warning reported by David Binderman and Sergey
Senozhatsky. The old version was working correctly but was not easy to read.

Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:06 -05:00
Takahiro Yasui
5c10e63c94 [SCSI] limit state transitions in scsi_internal_device_unblock
scsi timeout on two or more devices may cause extremely long execution
time for user applications because SDEV_OFFLINE state is changed to
SDEV_RUNNING state during scsi error recovery procedures triggered by
a bus reset or a host reset of scsi LLD, and scsi timeout can happens
on the same devices many times.

This happens because scsi_internal_device_unblock() changes device's
state to SDEV_RUNNING even if a device in other states than SDEV_BLOCK,
while the following two transitions are required in this function.

  SDEV_BLOCK -> SDEV_RUNNING
  SDEV_CREATED_BLOCK -> SDEV_CREATED

Otherwise, it returns -EINVAL.

Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
[matthew@wil.cx: supplied rewritten base for patch]
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-23 15:44:05 -05:00
Martin K. Petersen
ae03bf639a block: Use accessor functions for queue limits
Convert all external users of queue limits to using wrapper functions
instead of poking the request queue variables directly.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-22 23:22:54 +02:00
Martin K. Petersen
e1defc4ff0 block: Do away with the notion of hardsect_size
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case.  The
sector size will be 4KB but the logical block size will remain
512-bytes.  Hence we need to distinguish between the physical block size
and the logical ditto.

This patch renames hardsect_size to logical_block_size.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-22 23:22:54 +02:00
Jens Axboe
e4b636366c Merge branch 'master' into for-2.6.31
Conflicts:
	drivers/block/hd.c
	drivers/block/mg_disk.c

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-22 20:25:34 +02:00
Randy Dunlap
b0d428adeb [SCSI] fcoe, libfc: fix function declarations to be ANSI-compliant
Fix function declarations:

drivers/scsi/fcoe/fcoe.c:1356:28: warning: non-ANSI function declaration of function 'fcoe_dev_setup'
drivers/scsi/libfc/fc_rport.c:1293:20: warning: non-ANSI function declaration of function 'fc_setup_rport'
drivers/scsi/libfc/fc_rport.c:1302:23: warning: non-ANSI function declaration of function 'fc_destroy_rport'

[jejb: fixed wrong doc in comment noticed during inspection]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:15 -05:00
FUJITA Tomonori
73da9c13d4 [SCSI] scsi_debug: fix virtual disk larger than 1TB
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:15 -05:00
Kleber S. Souza
f381642d8f [SCSI] ipr: ipr_remove() marked __devexit
Marking the ipr clean up function ipr_remove() as __devexit and using
__devexit_p() macro in its address reference.

Signed-off-by: Kleber Sacilotto de Souza <kleber@linux.vnet.ibm.com>
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:15 -05:00
Chauhan, Vijay
8f03226358 [SCSI] scsi_dh_rdac: Retry for NOT_READY(02/04/01) in rdac device handler
During device discovery read capacity fails with 0x020401 and sets the
device size to 0. As a reason any I/O submitted to this path gets
killed at sd_prep_fn with BLKPREP_KILL. This patch is to retry for
0x020401. NEED_RETRY in scsi_decide_disposition does not give
sufficient time for the device to become ready.

Signed-off-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:14 -05:00
Aaro Koskinen
fa8584566c [SCSI] sym53c8xx_2: slave_alloc/destroy safety (2.6.27.5)
Make the sym53c8xx_2 driver slave_alloc/destroy less unsafe. References
to the destroyed LCB are cleared from the target structure (instead of
leaving a dangling pointer), and when the last LCB for the target is
destroyed the reference to the upper layer target data is cleared. The
host lock is used to prevent a race with the interrupt handler. Also
user commands are prevented for targets with all LCBs destroyed.

Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:14 -05:00
Aaro Koskinen
410604d25f [SCSI] sym53c8xx_2: lun to_clear flag not re-initialized (2.6.27.5)
(Resent with proper formatting)

Fix for the sym53c8xx_2 driver to initialize lun's to_clear flag after
a bus reset (a failed clear can trigger a bus reset and it should not
be attemped again after that).

Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:14 -05:00
Michael Reed
413e6e18b4 [SCSI] qla1280: error recovery rewrite
The driver now waits for the scsi commands associated with a
particular error recovery step to be returned to the mid-layer,
and returns the appropriate SUCCESS or FAILED status.  Removes
unneeded polling of chip for interrupts.

This patch also bumps the driver version number.

Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:13 -05:00
Michael Reed
fd65e5e93c [SCSI] qla1280: driver clean up
Remove some unneeded, inactive and unused code, make some trivial
corrections to comments and a printk, and return a proper status
in qla1280_queuecommand.  No fundamental logic changes are made.

Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:13 -05:00
Alan Stern
14faf12f7d [SCSI] Increase default timeout for INQUIRY
This patch (as1224) changes the default timeout for INQUIRY commands
from 3 seconds to 20 seconds, which is the value used by Windows for
USB Mass-Storage devices.  Some of these devices, like the Corsair
Flash Voyager (see Bugzilla #12188) really do need a long timeout.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:13 -05:00
Andy Yan
20b09c2992 [SCSI] mvsas: add support for 94xx; layout change; bug fixes
This version contains following main changes
  - Switch to new layout to support more types of ASIC.
  - SSP TMF supported and related Error Handing enhanced.
  - Support flash feature with delay 2*HZ when PHY changed.
  - Support Marvell 94xx series ASIC for 6G SAS/SATA, which has 2
88SE64xx chips but any different register description.
  - Support SPI flash for HBA-related configuration info.
  - Other patch enhanced from kernel side such as increasing PHY type

[jejb: fold back in DMA_BIT_MASK changes]
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:12 -05:00
Jeff Garzik
dd4969a892 [SCSI] mvsas: split driver into multiple files
Split mvsas driver into multiple source codes, based on the split
and function distribution found in Marvell's mvsas update.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:12 -05:00
Jeff Garzik
2ad52f473b [SCSI] mvsas: move into new directory drivers/scsi/mvsas/
Zero functional changes, just file movement.

This commit prepares for the upcoming integration of the
Marvell-provided driver update that splits the driver into support
for both 64xx and 94xx chip families.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:12 -05:00
Andrew Vasquez
a03706017e [SCSI] qla2xxx: Update version number to 8.03.01-k2.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:11 -05:00
Anirban Chakraborty
e5b68a61e1 [SCSI] qla2xxx: Use port number to compute nvram/vpd parameter offsets.
Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:11 -05:00
Andrew Vasquez
e337d9070e [SCSI] qla2xxx: Add an override option to specify ISP firmware load semantics.
As it may be useful during debugging to use a specific firmware
image.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:11 -05:00
Andrew Vasquez
b469a7cbe9 [SCSI] qla2xxx: Don't try to 'stop' firmware if already in ROM code.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:10 -05:00
Michael Reed
a13d8ac057 [SCSI] qla2xxx: Conditionally disable automatic queue full tracking.
Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.

The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth.  If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth.  While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.

This patch implements an "off switch" as a module parameter.

Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:10 -05:00
Joe Carnuccio
e1f916035f [SCSI] qla2xxx: Perform an implicit login to the Management Server.
Set the conditional plogi option bit whenever logging in the
fabric management server (if it is already logged in, it does not
need an explicit login; an implicit login suffices).

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:09 -05:00
Andrew Vasquez
7d0dba174a [SCSI] qla2xxx: Restrict model-name/description device-table usage.
Information present in static table is only valid for pre-ISP25xx
adapters.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:09 -05:00
Harish Zunjarrao
fc3ea9bcb8 [SCSI] qla2xxx: Correct hard-coded address of a second-port's NVRAM.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:09 -05:00
Andrew Vasquez
8f97975136 [SCSI] qla2xxx: Correct typo in read_nvram() callback.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:08 -05:00
Anirban Chakraborty
67c2e93ae7 [SCSI] qla2xxx: Remove reference to request queue from scsi request block.
srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:08 -05:00
Anirban Chakraborty
68ca949cdb [SCSI] qla2xxx: Add CPU affinity support.
Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:08 -05:00
Anirban Chakraborty
2afa19a937 [SCSI] qla2xxx: Add QoS support.
Set the number of request queues to the module paramater
ql2xmaxqueues.  Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:07 -05:00
Andrew Vasquez
7640335ea5 [SCSI] qla2xxx: Correct compilation failures when DEBUG'n' options are enabled.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:07 -05:00
Andrew Vasquez
bad7001c20 [SCSI] qla2xxx: Export additional FCoE attributes for application support.
Cull and export VN_Port MAC address and VLAN_ID information on
supported FCoE ISPs.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:07 -05:00
Seokmann Ju
d53b48d512 [SCSI] qla2xxx: Correct bus-reset behaviour with recent ISPs.
The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process.  The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.

Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-20 17:21:06 -05:00
Boaz Harrosh
ac36552a52 scsi_lib: remove unused variable
The last request completion cleanup in scsi_lib left an unused
this_count variable in scsi_io_completion().
(It was used before in a code segment that now uses blk_end_request_all())

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-19 19:54:09 +02:00
Boaz Harrosh
c29b70f6ee libosd: Use of new blk_make_request
Use new blk_make_request() to allocate a request from bio
and avoid using deprecated blk_rq_append_bio().

This patch is dependent on a block layer patch titled:
    [BLOCK] New blk_make_request() takes bio returns request

This is the last usage of blk_rq_append_bio in osd, it can now
be un-exported.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Jeff Garzik <jeff@garzik.org>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-19 12:14:56 +02:00
Boaz Harrosh
bc38bf106c libosd: Use new blk_rq_map_kern
Now that blk_rq_map_kern will append the buffer onto the
request we can use it easily for adding extra segments
(eg. attributes)

This patch is dependent on a block layer patch titled:
   [BLOCK] allow blk_rq_map_kern to append to requests

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-19 12:14:55 +02:00
Tejun Heo
5f49f63178 block: set rq->resid_len to blk_rq_bytes() on issue
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero.  The conversion was done under the assumption that
when a request fails residue count wasn't defined.  However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.

This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers.  While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.

* ide-cd: rq->resid_len cleared on pc success

* mptsas: req->resid_len cleared on success

* sas_expander: rsp/req->resid_len cleared on success

* mpt2sas_transport: req->resid_len cleared on success

* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
  advantage of initial full count to simplify code

Boaz Harrosh spotted bug in resid_len initialization.  Fixed as
suggested.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-19 11:36:08 +02:00
David S. Miller
bb803cfbec Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/scsi/fcoe/fcoe.c
2009-05-18 21:08:20 -07:00
Eric Moore
2b69a8a2b6 [SCSI] mpt2sas: fix driver version inconsistency
In Commit

commit 3b8b5c9b1f
Author: Eric Moore <eric.moore@lsi.com>
Date:   Tue Apr 21 15:44:27 2009 -0600

    [SCSI] mpt2sas : bump driver version to 01.100.02.00
 
The MPT2SAS_MAJOR_VERSION didn't get bumped from 00 to 01 so
applications will see it incorrectly as 00.100.02.00 driver instead of
01.100.02.00.  Fix by making MPT2SAS_MAJOR_VERSION match the major
number in MPT2SAS_DRIVER_VERSION

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-18 14:17:17 -05:00
Ingo Molnar
1079cac0f4 Merge commit 'v2.6.30-rc6' into tracing/core
Merge reason: we were on an -rc4 base, sync up to -rc6

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-05-18 10:15:35 +02:00
Vasu Dev
184dd3459b fcoe: adds spma mode support
If we can find a type NETDEV_HW_ADDR_T_SAN mac address from the
corresponding netdev for a fcoe interface then sets up added the
fc->ctlr.spma flag and stores spma mode address in ctl_src_addr.

In case the spma flag is set then:-

 1. Adds spma mode MAC address in ctl_src_addr as secondary
    MAC address, the FLOGI for FIP and pre-FIP will go out
    using this address.
 2. Cleans up stored spma MAC address in ctl_src_addr in
    fcoe_netdev_cleanup.
 3. Sets up spma bit in fip_flags for FIP solicitations along
    with exiting FPMA bit setting.
 4. Initialize the FLOGI FIP MAC descriptor to stored spma
    MAC address in ctl_src_addr. This is used as proposed
    FCoE MAC address from initiator along with both SPMA
    and FPMA bit set in FIP solicitation, in response the
    switch may grant any FPMA or SPMA mode MAC address to
    initiator.

Removes FIP descriptor type checking against ELS type
ELS_FLOGI in fcoe_ctlr_encaps to update a FIP MAC descriptor,
instead now checks against FIP_DT_FLOGI.

I've tested this with available FPMA-only FCoE switch but
since data_src_addr is updated using same old code for
both FPMA and SPMA modes with FIP or pre-FIP links, so added
SPMA mode will work with SPMA-only switch also provided that
switch grants a valid MAC address.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:08 -07:00
Vasu Dev
ab6b85c1d7 fcoe: consolidates netdev related config and cleanup for spma mode
Currently fcoe_netdev_config adds netdev pkt handler for fcoe pkts,
fcoe_if_create adds netdev pkt handler for fip packets, a secondary
MAC address is added by fcoe_netdev_config and then later cleanup
for these netdev related config/adds is done only during
fcoe_if_destroy and no cleanup done on error during fcoe interface
creation after above netdev config calling in fcoe_if_create.

So this patch adds single func for above mentioned cleanup the
fcoe_netdev_cleanup and then calls this func on either fcoe interface
destroy or exiting from fcoe_if_create due to an error after fcoe/fip
related above netdev config is done.

Moved netdev pkt handler addition code blocks for fip pkts close to
similar code block for foce pkt in fcoe_netdev_config, so that added
fcoe_netdev_cleanup could be called on error from fcoe_netdev_config
to undo these both additions for fcoe/fip pkt handlers. This move
required reference to fcoe_fip_recv in fcoe_netdev_config, so moved
fip related functions fcoe_fip_recv, fcoe_fip_send and
fcoe_update_src_mac above fcoe_netdev_config.

This consolidation will enable spma mode support in next patch to
easily add or delete spma mode mac address beside fixing current
no cleanup issue during error.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-17 21:04:08 -07:00
adam radford
7b14f58ad6 [SCSI] 3w-xxxx: scsi_dma_unmap fix
This patch fixes the following regression that occurred during the
scsi_dma_map()/unmap()
changes when compiling with CONFIG_DMA_API_DEBUG=y :

WARNING: at lib/dma-debug.c:496 check_unmap+0x142/0x542()
Hardware name:
3w-xxxx 0000:02:02.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]

Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-15 12:24:59 -04:00
adam radford
8454e9888c [SCSI] 3w-9xxx: scsi_dma_unmap fix
This patch fixes the following regression the occurred during the
scsi_dma_map()/unmap() changes:

3w-9xxx 0001:45:00.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]

Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-15 12:23:32 -04:00
Andrew Vasquez
9a1a69a1f4 [SCSI] fc-transport: Close state transition-window during rport deletion.
Andrew Vasquez wrote:
> fc-transport: Close state transition-window during rport deletion.
>
> After an rport's state has transitioned to FC_PORTSTATE_BLOCKED,
> but, prior to making the upcall to 'block' the scsi-target
> associated with an rport, queued commands can recycle and
> ultimately run out of retries causing failures to propagate to
> upper-level drivers.  Close this transition-window by returning
> the non-'retries' modifying DID_IMM_RETRY status for submitted
> I/Os.

The same can happen for iscsi when transitioning from logged in
to failed and blocking the sdevs.

This patch converts iscsi and fc's transitions back to use DID_IMM_RETRY
instead of DID_TRANSPORT_DISRUPTED which has a limited number of retries
that we do not want to use for handling this race.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
[Addition of iscsi and fc port online devloss case conversion by Mike Christie]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-15 12:16:46 -04:00
Edward Goggin
c53a284f8b [SCSI] initialize max_target_blocked in scsi_alloc_target
This patch initializes the max_target_blocked field of a scsi target
structure so that a queuecommand return value of
SCSI_MLQUEUE_TARGET_BUSY will actually result in having the
scsi_queue_insert blocking the device queue before requeuing the
command and running the queue.  Otherwise, can and does cause livelock
on single CPU configurations if/when open-iSCSI software initiator's
command PDU window fills.

Signed-off-by: Ed Goggin <egoggin@vmware.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-14 17:17:46 -04:00
Abhijeet Joglekar
5df6d737dd [SCSI] fnic: Add new Cisco PCI-Express FCoE HBA
fnic is a driver for the Cisco PCI-Express FCoE HBA

Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-05-13 22:13:09 -04:00
Tejun Heo
e458824f9d scsi: fix resid_len mis-conversion in scsi_end_request()
Commit c3a4d78c58 introduced
rq->data_len and converted residual count users to it.  While
converting, it mistakenly converted scsi_end_request() to finish
requests with residual count when it wants to do is fully complete the
request.  Fix it by using blk_end_request_all() instead.

This bug was spotted by Boaz Harrosh.

Signed-off-by: Tejun Heo <tj@kernel.org>
Spotted-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-12 08:49:32 +02:00
FUJITA Tomonori
e6bb7a96c2 scsi: simplify the bidi completion
Let's use blk_end_request_all() instead of blk_end_bidi_request().

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 11:06:47 +02:00
Tejun Heo
9934c8c045 block: implement and enforce request peek/start/fetch
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request().  After that, drivers are free to either dequeue it
or process it without dequeueing.  Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.

Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary.  However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing.  Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.

Previous patches converted all block low level drivers to dequeueing
model.  This patch completes the API transition by...

* renaming elv_next_request() to blk_peek_request()

* renaming blkdev_dequeue_request() to blk_start_request()

* adding blk_fetch_request() which is combination of peek and start

* disallowing completion of queued (not started) requests

* applying new API to all LLDs

Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.

[ Impact: block request issue API cleanup, no functional change ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 09:52:18 +02:00
Tejun Heo
1011c1b9f2 block: blk_rq_[cur_]_{sectors|bytes}() usage cleanup
With the previous changes, the followings are now guaranteed for all
requests in any valid state.

* blk_rq_sectors() == blk_rq_bytes() >> 9
* blk_rq_cur_sectors() == blk_rq_cur_bytes() >> 9

Clean up accessor usages.  Notable changes are

* nbd,i2o_block: end_all used instead of explicit byte count
* scsi_lib: unnecessary conditional on request type removed

[ Impact: cleanup ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 09:50:55 +02:00
Tejun Heo
b079041030 block: cleanup rq->data_len usages
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes().  Convert all non-IDE direct
users to accessors.  IDE will be converted in a separate patch.

Boaz: spotted incorrect data_len/resid_len conversion in osd.

[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 09:50:55 +02:00
Tejun Heo
83096ebf12 block: convert to pos and nr_sectors accessors
With recent cleanups, there is no place where low level driver
directly manipulates request fields.  This means that the 'hard'
request fields always equal the !hard fields.  Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.

While at it, drop superflous blk_rq_pos() < 0 test in swim.c.

[ Impact: use pos and nr_sectors accessors ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 09:50:54 +02:00
Tejun Heo
5b93629b45 block: implement blk_rq_pos/[cur_]sectors() and convert obvious ones
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.

This is in preparation of request data length handling cleanup.

Geert	: suggested adding const to struct request * parameter to accessors
Sergei	: spotted error in patch description

[ Impact: cleanup ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 09:50:53 +02:00
Tejun Heo
c3a4d78c58 block: add rq->resid_len
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion.  This duality creates some
headaches.

First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing.  It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count.  This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.

Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred.  The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all.  This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.

This patch adds rq->resid_len which is used only for residual count.

While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.

Boaz	: spotted missing conversion in osd
Sergei	: spotted too early conversion to blk_rq_bytes() in ide-tape

[ Impact: cleanup residual count handling, report 0 resid by default ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 09:50:53 +02:00
Al Viro
e24977d45f Reduce path_lookup() abuses
... use kern_path() where possible

[folded a fix from rdd]

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2009-05-09 10:49:42 -04:00
Ingo Molnar
44347d947f Merge branch 'linus' into tracing/core
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
              on a handful of tracing fixes present in .30-rc5-almost.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-05-07 11:17:34 +02:00
Tejun Heo
731ec497e5 block: kill rq->data
Now that all block request data transfer is done via bio, rq->data
isn't used.  Kill it.

While at it, make the roles of rq->special and buffer clear.

[ Impact: drop now unncessary field from struct request ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Boaz Harrosh <bharrosh@panasas.com>
2009-04-28 07:37:36 +02:00
Tejun Heo
40cbbb781d block: implement and use [__]blk_end_request_all()
There are many [__]blk_end_request() call sites which call it with
full request length and expect full completion.  Many of them ensure
that the request actually completes by doing BUG_ON() the return
value, which is awkward and error-prone.

This patch adds [__]blk_end_request_all() which takes @rq and @error
and fully completes the request.  BUG_ON() is added to to ensure that
this actually happens.

Most conversions are simple but there are a few noteworthy ones.

* cdrom/viocd: viocd_end_request() replaced with direct calls to
  __blk_end_request_all().

* s390/block/dasd: dasd_end_request() replaced with direct calls to
  __blk_end_request_all().

* s390/char/tape_block: tapeblock_end_request() replaced with direct
  calls to blk_end_request_all().

[ Impact: cleanup ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-28 07:37:35 +02:00
Boaz Harrosh
e9da4d7f73 [SCSI] libosd: OSD2r05: on-the-wire changes for latest OSD2 revision 5.
OSC's OSD2 target: [git clone git://git.open-osd.org/osc-osd/ master]
(Initiator code prior to this patch must use: "git checkout CDB_VER_OSD2r01"
 in the target tree above)

This is a summery of the wire changes:

 * OSDv2_ADDITIONAL_CDB_LENGTH == 192 => 228 (Total CDB is now 236 bytes)
 * Attributes List Element Header grew, so attribute values are 8 bytes
   aligned.
 * Cryptographic keys and signatures are 20 => 32
 * Few new definitions.

(Still missing new standard definitions attribute values, these do not change
 wire format and will be added later when needed)

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 11:05:49 -05:00
Boaz Harrosh
f8d3a644be [SCSI] libosd: OSD2r05: OSD_CRYPTO_KEYID_SIZE will grow 20 => 32 bytes
In OSD2r04 draft, cryptographic key size changed to 32 bytes from
OSD1's 20 bytes. This causes a couple of on-the-wire structures
to change, including the CDB.

In this patch the OSD1/OSD2 handling is separated out in regard
to affected structures, but on-the-wire is still the same. All
on the wire changes will be submitted in one patch for bisect-ability.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 11:05:41 -05:00
Boaz Harrosh
71f32e31e5 [SCSI] libosd: OSD2r05: Prepare for rev5 attribute list changes
In OSD2r05 draft each attribute list element header was changed
so attribute-value would be 8 bytes aligned. In OSD2r01-r04
it was aligned on 2 bytes. (This is because in OSD2r01 the complete
element was 8 bytes padded at end but the header was not adjusted
and caused permanent miss-alignment.)

OSD1 elements are not padded and might be or might not be aligned.
OSD1 is still supported.

In this code we do all the code re-factoring to separate OSD1/OSD2
differences but do not change actual wire format. All wire format
changes will happen in one patch later, for bisect-ability.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 11:05:40 -05:00
Dan Carpenter
bf5e84f696 [SCSI] libosd: fix potential ERR_PTR dereference in osd_initiator.c
bio_map_kern() returns an ERR_PTR() not NULL.

Found by smatch (http://repo.or.cz/w/smatch.git).  Compile tested.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 11:05:31 -05:00
Eric Moore
3b8b5c9b1f [SCSI] mpt2sas : bump driver version to 01.100.02.00
Bump driver version.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:54:17 -05:00
Eric Moore
6f92a7a0af [SCSI] mpt2sas: fix hotplug event processing
Here's a fix for hotplug events.  The useage of queue_delayed_work seems
to broke the fifo for processing of firmware events.  After several iterations
of adding and removing cabling connected to jbods, the devices are not
getting added becuase kernel thread is activited out of order.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:54:15 -05:00
Eric Moore
99bb214b1b [SCSI] mpt2sas : release diagnotic buffers prior host reset
Diagnostic buffer support is already there in the driver.  This support allows
applications to pull ring buffers from controller firmware for debugging
firmware related issues.

What this patch does is sends reqeust to firmware to release the buffers prior
to host reset.   This will allow what ever debug info is there prior to reset
to be dma'd to host memory. With out this fix, some of the debug data would
been lost.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:54:04 -05:00
Eric Moore
8901cbb45e [SCSI] mpt2sas : Broadcast Primative AEN bug fix
Bug fix in the broadcast primative async event code where the driver would
stop sending tm queries after the first queury was completed. This was due
driver not reseting the tm_cmds.status field back to MPT2_CMD_NOT_USED after
completing a task management request.

An addtional fix adding sanity check to insure sas_device->starget set to NULL.
During multipath testing fail over/fail back, the mid layer was holding onto
sdev longer than the fail back period, thus starget was getting set to NULL
for device being added.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:54:02 -05:00
Eric Moore
f0f9cc1fb8 [SCSI] mpt2sas : Identify Dell series-7 adapters at driver load time
The Dell branding along with the VID, DID, SSVID, SSDID following the LSI
branding that contains the card firmware/chip/bios versions.  If the SSDID
is not known but it is a Dell HBA, the driver will print the SSDID instead
of the Dell branding string.  Nothing will be printed for non Dell HBAs

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:54:00 -05:00
Eric Moore
e5f9bb198a [SCSI] mpt2sas : driver name needs to be in the MPT2IOCINFO ioctl
The driver name needs to be at the beginining of the driver_version string in
MPT2IOCINFO ioctl.  This is the same behaviour is there already in the mptsas
driver.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:53:58 -05:00
Eric Moore
77bdd9ee1e [SCSI] mpt2sas : running out of message frames
The driver is not freeing message frame when returning failure from
_ctl_do_task_abort.   If you call this function 500 times when its unable
to find an active task mid, you end up with no message frames.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:53:57 -05:00
Eric Moore
0d04df9b4a [SCSI] mpt2sas : fix oops when firmware sends large sense buffer size
There is a bug in firmware where the reply message frame says there is a
16kb sense buffer, when in reality its only 20 bytes.  This fix insures
the memcpy action doesn't corrupte the memory beyond the 90 bytes allocated in
the scsi command for sense buffer.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:53:56 -05:00
Eric Moore
03ea111550 [SCSI] mpt2sas : the sanity check in base_interrupt needs to be on dword boundary
The poison sanity check on the reply_post_free register needs to be by 32bit,
not 64bit. The poison check is there because its possible that the driver read
the 1st 32bit before the 2nd 32bit has been written to by firmware.  In other
words, this handles race between driver reading the 64 bit register, and it
being dma'd across pci memory from controller firmware as two 32bit pci writes.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:53:53 -05:00
Eric Moore
fd01825c70 [SCSI] mpt2sas : unique ioctl magic number
The current magic number is shared with mptsas driver. This to be unique to
fix issues with register_ioctls32_conversion in older kernels.  We are making
this change across all versions of the sas2.0 drivers.

Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:53:46 -05:00
Dave Hansen
8f76d151b0 [SCSI] fix sign extension with 1.5TB usb-storage LBD=y
Shifting an unsigned char implicitly casts it to a signed int.  This
caused 'lba' to sign-extend and Linux would then try READ CAPACITY 16
which was not supported by at least one drive.  Using the
get_unaligned_be*() helpers keeps us from having to worry about how the
extension might occur.

Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:36:07 -05:00
Brian King
dd406ef895 [SCSI] ipr: Fix sleeping function called with interrupts disabled
The ata_sas_slave_configure was changed such that it now allocates
some memory for a drain buffer for ATAPI devices. Fixup the ipr
driver such that we no longer make this call with interrupts disabled.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:32:13 -05:00
Joe Eykholt
6401bdcad5 [SCSI] fcoe: fip: add multicast filter to receive FIP advertisements.
The FCoE forwarder (FCF) would be selected, but then would soon time
out after three advertisements were missed.  This would be 24 seconds
by default, or 3 times the keep-alive interval configured on the switch.

The cause was that the multicast address for all FIP E-nodes
was never added.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:19:35 -05:00
Robert Love
a29e7646f4 [SCSI] libfc: Fix compilation warnings with allmodconfig
When building with a .config generated from 'make allmodconfig'
some build warnings are generated. This patch corrects the warnings,
adds a FC_FID_NONE (= 0) enumeration for FC-IDs and cleans up one
variable naming to meet our variable naming conventions. For example,
fc_lport's should be named "lport," not "lp."

Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:19:31 -05:00
Chris Leech
dd3fd72e69 [SCSI] fcoe: fix spelling typos and bad comments
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:19:28 -05:00
Chris Leech
fc224a5bc9 [SCSI] fcoe: don't export functions that are internal to fcoe
These probably never should have been exported.
If they were needed outside of the fcoe module, they
would have been moved to libfcoe.

Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:19:25 -05:00
Dan Carpenter
3caf02ee28 [SCSI] fcoe: kfree() -> kfree_skb()
sk_buff pointers should use kfree_skb() instead of vanilla kfree().

Found by smatch (http://repo.or.cz/w/smatch.git).

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:19:23 -05:00
Abhijeet Joglekar
55c7a60cf0 [SCSI] libfc: whenever queueing delete ev for rport, set state to NONE
When a delete event is queued for an rport, set state to NONE so that no
other processing is done on the rport as it is being removed.

Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:19:03 -05:00
Abhijeet Joglekar
bbf156697a [SCSI] libfc: Change state to NONE in fc_lport_destroy
After lport_destroy, the local port should not be used again. Transition
to state NONE, any incoming frames or link up should not transition out
of this state since we are deleting exchange table and cleaning up the
local port. Also, mark link as down.

Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:19:01 -05:00
Abhijeet Joglekar
a0fd2e49ec [SCSI] libfc: During fabric logoff, flush the rport Q after logging off dns port
We want to generate the rport queue event (from the logoff)
before flushing the queue otherwise the event may still be
in the queue when we logoff.

Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:19:00 -05:00
Abhijeet Joglekar
b4c6f54632 [SCSI] libfc: Track rogue remote ports
Rogue ports are currently not tracked on any list. The only reference
to them is through any outstanding exchanges pending on the rogue ports.
If the module is removed while a retry is set on a rogue port
(say a Plogi retry for instance), this retry is not cancelled because there
is no reference to the rogue port in the discovery rports list. Thus the
local port can clean itself up, delete the exchange pool, and then the
rogue port timeout can fire and try to start up another exchange.

This patch tracks the rogue ports in a new list disc->rogue_rports. Creating
a new list instead of using the disc->rports list keeps remote port code
change to a minimum.

1)  Whenever a rogue port is created, it is immediately added to the
disc->rogue_rports list.

2) When the rogues port goes to ready, it is removed from the rogue list
and the real remote port is added to the disc->rports list

3) The removal of the rogue from the disc->rogue_rports list is done in
the context of the fc_rport_work() workQ thread in discovery callback.

4) Real rports are removed from the disc->rports list like before. Lookup
is done only in the real rports list. This avoids making large changes
to the remote port code.

5) In fc_disc_stop_rports, the rogues list is traversed in addition to the
real list to stop the rogue ports and issue logoffs on them. This way, rogue
ports get cleaned up when the local port goes away.

6) rogue remote ports are not removed from the list right away, but
removed late in fc_rport_work() context, multiple threads can find the same
remote port in the list and call rport_logoff(). Rport_logoff() only
continues with the logoff if port is not in NONE state, thus preventing
multiple logoffs and multiple list deletions.

7) Since the rport is removed from the disc list at a later stage
(in the disc callback), incoming frames can find the rport even if
rport_logoff() has been called on the rport. When rport_logoff() is called,
the rport state is set to NONE, and we are trying to cancel all exchanges
and retries on that port. While in this state, if an incoming
Plogi/Prli/Logo or other frames match the rport, we should not reply
because the rport is in the NONE state. Just drop the frame, since the
rport will be deleted soon in the disc callback (fc_rport_work)

8)  In fc_disc_single(), remove rport lookup and call to fc_disc_del_target.
fc_disc_single() is called from recv_rscn_req() where rport lookup
and rport_logoff is already done.

Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:18:57 -05:00
Abhijeet Joglekar
76f6804e7e [SCSI] libfc: Do not retry if the new state is not the same as old state
For instance, if there is a Plogi pending (remote port is in Plogi state),
and the state changes to say NONE (because the port is being logged off),
then when the Plogi resp times out, do not start a retry.

This patch partially reverts an earlier patch (libfc: check for err when
recv and state is incorrect), by moving the state check back to before
checking for error. However, if the state does not match, then there is
an additional check to see if its an error ptr or a real frame before
jumping to err or out respectively.

Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:18:51 -05:00
Abhijeet Joglekar
0d228c0f7f [SCSI] libfc: Hold disc mutex while processing gpn ft resp
gpn_ft_resp processing currently does not hold the discovery lock.
disc_done() thus gets called from gpn_ft_resp or from gpn_ft_parse
without the lock held. This then sets disc->pending to zero or calls
gpn_ft_req() without disc_lock held.

- Hold disc mutex during gpn_ft resp processing
- In disc_done, release the disc mutex while calling lport callback

Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:18:48 -05:00
kxie@chelsio.com
a53922ddcf [SCSI] cxgb3i: fix ddp map overrun
(version 2)

Fixed a bug in calculating ddp map range when search for free entries:
it was going beyond the end by one, thus corrupting gl_skb[0].

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:11:07 -05:00
Mike Christie
1393109f23 [SCSI] cxgb3i: fix cpu use abuse during writes
When doing a lot (128) of large writes (256K) we can hit the cxgb3_snd_win
check pretty easily. The driver's xmit thread then takes 100% of the cpu.

The driver should not be returning -EAGAIN for this problem. It should
be returing -ENOBUFS, then when the window is opened again it should
queue the xmit thread (it already wakes the xmit thread).

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:10:06 -05:00
Mike Christie
dd0af9f94e [SCSI] cxgb3i: fix can_queue and cmd_per_lun initialization
cxgb3i was setting can_queue to only 128 commands, and was
setting the can_queue and cmd_per_lun to the same value.

This sets the can_queue to 1024 commands, and sets the cmd_per_lun
to a safer default of 32.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:09:59 -05:00
Mike Christie
6b5d6c443a [SCSI] cxgb3i, iser, iscsi_tcp: set target can queue
Set target can queue limit to the number of preallocated
session tasks we have.

This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:09:54 -05:00
Mike Christie
9a6510eb3f [SCSI] iscsi_tcp: don't fire conn error if pdu init fails
If a command's scsi cmd pdu setup fails then we can just fail
the IO to the scsi layer. If a DATA_OUT for a R2T fails then
we will want to drop the session, because it means we got a
bad request from the target (iscsi protocol error).

This patch has us propogate the error upwards so libiscsi_tcp
or libiscsi can decide what the best action is to take. It
also fixes a bug where we could try to grab the session lock
while holding it, because if iscsi_tcp drops the session in the
pdu setup callout the session lock is held when setting up the
scsi cmd pdu.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 10:09:51 -05:00
Mike Christie
b4efdd586b [SCSI] fix q->lock not held warning when target is busy
We cannot call blk_plug_device from scsi_target_queue_ready
because the q lock is not held. And we do not need to call
it from there because when we return 0, the scsi_request_fn
not_ready handling will plug the queue for us if needed.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 09:48:10 -05:00
James Smart
e832b3ca65 [SCSI] lpfc 8.3.1 : Update version to 8.3.1
Update driver version to 8.3.1
Also update copyright end year for driver.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-04-27 09:43:19 -05:00