Since commit 16626b0cc3 the asix
driver depends on the phylib. Select phylib when the asix driver is
selected.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: kernel-janitors@vger.kernel.org
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes:
drivers/built-in.o: In function `qmi_wwan_bind_shared':
qmi_wwan.c:(.text+0x25b686): undefined reference to `usb_cdc_wdm_register'
make[1]: *** [.tmp_vmlinux1] Error 1
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces. The Huawei E392/E398 are examples of such devices.
These typically cannot be fully configured using AT commands
over a serial interface. It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.
The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function. This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.
Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver. To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.
You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing driver for the network port of Samsung Kalmia based USB LTE modems.
It has also an ACM interface that previous patches associates with the "option"
module. To access those interfaces, the modem must first be switched from modem
mode using a tool like usb_modeswitch.
As the proprietary protocol has been discovered by watching the MS Windows driver
behavior, there might be errors in the protocol handling, but stable and fast
connection has been established for hours with Norwegian operator NetCom that
distributes this modem with their LTE/4G subscription.
More and updated information about how to use this driver is available here:
http://www.draisberghof.de/usb_modeswitch/bb/viewtopic.php?t=465https://github.com/mkotsbak/Samsung-GT-B3730-linux-driver
Signed-off-by: Marius B. Kotsbak <marius@kotsbak.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
This patch adds support for the PL-25A1 by adding the appropriate
USB ID's. This chip is used in the Belkin 'Windows Easy Transfer'
Cables.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a driver for the CDC Ethernet part of this modem. The
device's ID is blacklisted in cdc_ether.c and is white-listed in
this new driver because of the quirks needed to make it useful.
The modem's firmware exposes a CDC ACM port for modem control and a
CDC Ethernet port for network data. The descriptors look fine but
both ports actually are some sort of multiplexers requiring non-
standard headers added/removed from every packet or they get
ignored. All information is based on a usb traffic log from a
Windows machine.
On the Verizon 4G network I've seen speeds up to 1.1MB/s so far with
this driver, a speed-o-meter site reports 16.2Mbps/10.5Mbps.
Userspace scripts are required to talk to the CDC ACM port.
Signed-off-by: Andrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch provides USB CDC NCM host driver support in the Linux Kernel.
Changes:
drivers/net/usb/cdc_ncm.c:
- initial submission of the CDC NCM host driver;
- verified on Intel 32/64 bit, Intel Atom, ST-Ericsson U8500 (ARM)
- throughput measured over 100 Mbits duplex;
- driver supports 16-bit NTB format only, but it is more than enough for
transfers up to 64K;
- driver can handle up to 32 datagrams in received NTB;
- timer is used to collect several packets in Tx direction
drivers/net/usb/Kconfig:
- a new entry to compile CDC NCM host driver
drivers/net/usb/Makefile:
- a new entry to compile CDC NCM host driver
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces cx82310_eth driver - driver for USB ethernet port of
ADSL routers based on Conexant CX82310 chips. Such routers usually have
ethernet port(s) too which are bridged together with the USB ethernet port,
allowing the USB-connected machine to communicate to the network (and also
internet through the ADSL, of course).
This is my first driver, so please check thoroughly. As there's no protocol
documentation, it was done with usbsnoop dumps from Windows driver, some
parts (the commands) inspired by cxacru driver and also other usbnet drivers.
The driver passed my testing - some real work and also pings sized from 0 to
65507 B.
The only problem I found is the ifconfig error counter. When I return 0 (or 1
but empty skb) from rx_fixup(), usbnet increases the error counter although
it's not an error condition (because packets can cross URB boundaries). Maybe
the usbnet should be fixed to allow rx_fixup() to return empty skbs (or some
other value, e.g. 2)?
The USB ID of my device is 0x0572:0xcb01 which conflicts with some ADSL modems
using cxacru driver (they probably use the same chipset but simpler
firmware). The modems seem to use bDeviceClass 0 and iProduct "ADSL USB
MODEM", my router uses bDeviceClass 255 and iProduct "USB NET CARD". The
driver matches only devices with class 255 and checks for the iProduct string
during init. I already posted a patch for the cxacru driver to ignore these
devices.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch removes the default from the Kconfig entry for sierra_net
driver as recommended.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Rory Filer <rfiler@sierrawireless.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-submitted based on comments from netdev community.
Summary of the changes:
1. Improved error handling.
2. Added the missing timeout arguments to usb_control_msg().
The following is a new Linux driver which exposes certain models of Sierra
Wireless modems to the operating system as Network Interface Cards (NICs).
This driver requires a version of the sierra.c driver which supports
blacklisting to work properly. The blacklist in sierra.c rejects the interfaces
claimed by sierra_net.c. Likewise, the sierra_net.c driver only accepts
(i.e. whitelists) the interface(s) used for USB-to-WWAN traffic.
The version of sierra.c which supports blacklisting is
available from the sierra wireless knowledge base page for older kernels. It is
also available in Linux kernel starting from version 2.6.31.
This driver works with all Sierra Wireless devices configured with PID=68A3
like USB305, USB306 provided the corresponding firmware version is I2.0
(for USB305) or M3.0 (for USB306) and later.
This driver will not work with earlier firmware versions than the ones shown
above. In this case the driver will issue an error message indicating
incompatibility and will not serve the device's USB-to-WWAN interface.
Sierra_net.c sits atop a pre-existing Linux driver called usbnet.c.
A series of hook functions are provided in sierra_net.c which are called by
usbnet.c in response to a particular condition such as receipt or transmission
of a data packet. As such, usbnet.c does most of the work of making
a modem appear to the system as a network device and for properly exchanging
traffic between the USB subsystem and the Network card interface.
Sierra_net.c is concerned with managing the data exchanged between the
USB-to-WWAN interface and the upper layers of the operating system.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Rory Filer <rfiler@sierrawireless.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for SMSC's LAN7500 family of USB 2.0
to gigabit ethernet adapters. It's loosely based on the smsc95xx
driver but the device registers for LAN7500 are completely different.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds five PID's to the whitelist set of devices.
Devices added to the whitelist:
Dell Wireless 5530 HSPA
Ericsson Mobile Broadband Module variants (F3507g, F3607gw and F3307)
Toshiba F3507g
Signed-off-by: Jonas Sjöquist <jonas.sjoquist@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a CDC Ethernet Emulation Model (EEM) host side
driver to support USB EEM devices.
EEM is different from the Ethernet Control Model (ECM) currently
supported by the "CDC Ethernet" driver. One key difference is
that it doesn't require of USB interface alternate settings to
manage interface state; some maldesigned hardware can't handle
that part of USB. It also avoids a separate USB interface for
control and status updates.
[ dbrownell@users.sourceforge.net: fix skb leaks, add rx packet
checks, improve fault handling, EEM conformance updates, cleanup ]
Signed-off-by: Omar Laazimani <omar.oberthur@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb driver for intellon int51x1 based PLC like devolo dlan duo
with improvements suggested by the guys of the mailinglist:
- name and prefix with int51x1 (Florian Fainelli)
- use conversion functions cpu_to_le16 / le16_to_cpu (Oliver Neukum)
- use pskb_may_pull instead of skb->len (Ilpo Järvinen)
- better code in tx_fixup (Ilpo Järvinen)
- use gotos for error handling (Ilpo Järvinen)
- better description (Jon Smirl)
Signed-off-by: Peter Holik <peter@holik.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attached is a driver for SMSC's LAN9500 USB2.0 10/100 ethernet
adapter.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Kconfig for the new "Option" driver so it's not in the
middle of the usbnet-based drivers, so the dependency displays
in the Kconfig user interfaces don't get trashed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This driver is for a number of different Option devices. Originally
written by Option and Andrew Bird, but cleaned up massivly for
acceptance into mainline by me and others.
Many thanks to the following for their help in cleaning up the driver by
providing feedback and patches to it:
- Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
- Oliver Neukum <oliver@neukum.org>
- Alan Cox <alan@lxorguk.ukuu.org.uk>
- Javier Marcet <javier@krausbeck.org>
Cc: Andrew Bird <ajb@spheresystems.co.uk>
Cc: Javier Marcet <javier@krausbeck.org>
Cc: Filip Aben <f.aben@option.com>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The asix usb driver currently depends on NET_ETHERNET which means you
cannot enable this driver if you only have 1000mbit enabled in your kernel.
Since there is no real dependency between the NET_ETHERNET portion and the
asix driver, simply drop it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All this USB_USBNET_MII trickery is simply not worth it considering how
few code it saves.
As a side effect, this also fixes the following compile error reported
by Toralf Förster:
<-- snip -->
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `usbnet_set_settings':
(.text+0xf1876): undefined reference to `mii_ethtool_sset'
drivers/built-in.o: In function `usbnet_get_settings':
(.text+0xf1836): undefined reference to `mii_ethtool_gset'
drivers/built-in.o: In function `usbnet_get_link':
(.text+0xf18d6): undefined reference to `mii_link_ok'
drivers/built-in.o: In function `usbnet_nway_reset':
(.text+0xf18f6): undefined reference to `mii_nway_restart'
make: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the file link in the Pegasus USB network driver's help text.
Signed-off-by: Cal Peake <cp@absolutedigital.net>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Replace invisible character with a space.
The diff looks like this on my terminal:
- <A0>Choose this option if you're using a host-to-host cable
- <A0>with one of these chips.
+ Choose this option if you're using a host-to-host cable
+ with one of these chips.
Reported by: Massimo Maiurana <maiurana@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Massimo Maiurana <maiurana@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus. When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer. Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
