An extended ping test with 6 vlans resulted in a driver oops with a
netdev transmit timeout.
Fix WATCHDOG_TIMEOUT to be more like e1000e at 5 * HZ, to avoid
unnecessary transmit timeouts.
Signed-off-by: Andy Cress <andy.cress@us.kontron.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch makes use of skb->data on Tx and the virtual address of the pages
allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong pointer variable is being used to parse the rss hash from
receive completions leading to corrupted rss_hash values filled into skb.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFS filter id can't have the special value RPS_NO_FILTER,
need to skip it when allocating id's.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attempting to disable ethernet autonegation via ethtool,
the pch_gpe driver will set software reset bit of PHY chip, But
control register of PHY chip of FRI2 will reenable ethernet autonegation.
Signed-off-by: Wei Yang <w90p710@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "WIZnet devices" config option should depend on HAS_IOMEM as
all wiznet drivers require it as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are seeing an oops in be_get_fw_log_level on ppc64 where we walk
off the end of memory.
commit 941a77d582 (be2net: Fix to allow get/set of debug levels in
the firmware.) requires byteswapping of num_modes and num_modules.
Cc: stable@vger.kernel.org # 3.5+
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Sathya Perla <sperla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the mlx4 drivers don't have the necessary callbacks to
implement EEH errors detection and recovery, so the PCI layer uses the
probe and remove callbacks to try to recover the device after an error on
the bus. However, these callbacks have race conditions with the internal
catastrophic error recovery functions, which will also detect the error
and this can cause the system to crash if both EEH and catas functions
try to reset the device.
This patch adds the necessary error recovery callbacks and makes sure
that the internal catastrophic error functions will not try to reset the
device in such scenarios. It also adds some calls to
pci_channel_offline() to suppress reads/writes on the bus when the slot
cannot accept I/O operations so we prevent unnecessary accesses to the
bus and speed up the device removal.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clk patches added code to get and enable clocks in the
respective driver probe functions. If the probe function failed
for some reason after enabling the clock, the clock was not
disabled again in many cases.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lumm <andrew@lunn.ch>
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
- Updates to the qib low-level driver
- First chunk of changes for SR-IOV support for mlx4 IB
- RDMA CM support for IPv6-only binding
- Other misc cleanups and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=f09j
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Updates to the qib low-level driver
- First chunk of changes for SR-IOV support for mlx4 IB
- RDMA CM support for IPv6-only binding
- Other misc cleanups and fixes
Fix up some add-add conflicts in include/linux/mlx4/device.h and
drivers/net/ethernet/mellanox/mlx4/main.c
* tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
IB/qib: checkpatch fixes
IB/qib: Add congestion control agent implementation
IB/qib: Reduce sdma_lock contention
IB/qib: Fix an incorrect log message
IB/qib: Fix QP RCU sparse warnings
mlx4: Put physical GID and P_Key table sizes in mlx4_phys_caps struct and paravirtualize them
mlx4_core: Allow guests to have IB ports
mlx4_core: Implement mechanism for reserved Q_Keys
net/mlx4_core: Free ICM table in case of error
IB/cm: Destroy idr as part of the module init error flow
mlx4_core: Remove double function declarations
IB/mlx4: Fill the masked_atomic_cap attribute in query device
IB/mthca: Fill in sq_sig_type in query QP
IB/mthca: Warning about event for non-existent QPs should show event type
IB/qib: Fix sparse RCU warnings in qib_keys.c
net/mlx4_core: Initialize IB port capabilities for all slaves
mlx4: Use port management change event instead of smp_snoop
IB/qib: RCU locking for MR validation
IB/qib: Avoid returning EBUSY from MR deregister
IB/qib: Fix UC MR refs for immediate operations
...
In boards with 4-ports, Tx LPI statistics were gathered incorrectly.
This patch guarantees that each pmf will only query its own port for
these statistics.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 036dafa28d.
First it appears in bisection, then reverting it solves the usual
netdev watchdog problem for different people. I don't have a proper
fix yet so get rid of it.
Bisected-and-reported-by: Alex VillacÃs Lasso <a_villacis@palosanto.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree will supply the register bank base addresses, make
register addressing relative to those. PHY connection is now
described by the device tree.
The OCTEON_IRQ_MII{0,1} symbols are also removed as they are now
unused and interfere with the irq_domain used for device tree irq
mapping.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3941/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 57840 boards come in two flavours: 2 x 20G and 4 x 10G.
To better differentiate between the two flavours, a separate device ID
was assigned to each.
The silicon default value is still the currently supported 57840 device ID
(0x168d), and since a user can damage the nvram (e.g., 'ethtool -E')
the driver will still support this device ID to allow the user to amend the
nvram back into a supported configuration.
Notice this patch contains lines longer than 80 characters (strings).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return
value to be consistent with the rest of the checks after niu_rbr_add_page()
calls in this file.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Neptune ethernet driver to check dma mapping error after map_page()
interface returns.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pm_runtime support to the TI Davinci EMAC driver.
CC: Sekhar Nori <nsekhar@ti.com>
CC: Kevin Hilman <khilman@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The '#include <mach/mux.h>' line in davinci_emac.c
causes a compile error because that header file
isn't found. It turns out that the #include isn't
needed because the driver isn't (and shoudn't be)
touching the mux anyway, so remove it.
CC: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
--------------------
This series contains updates to ixgbe and ixgbevf.
...
Akeem G. Abodunrin (1):
igb: reset PHY in the link_up process to recover PHY setting after
power down.
Alexander Duyck (8):
ixgbe: Drop probe_vf and merge functionality into ixgbe_enable_sriov
ixgbe: Change how we check for pre-existing and assigned VFs
ixgbevf: Add lock around mailbox ops to prevent simultaneous access
ixgbevf: Add support for PCI error handling
ixgbe: Fix handling of FDIR_HASH flag
ixgbe: Reduce Rx header size to what is actually used
ixgbe: Use num_tcs.pg_tcs as upper limit for TC when checking based
on UP
ixgbe: Use 1TC DCB instead of disabling DCB for MSI and legacy
interrupts
Don Skidmore (1):
ixgbe: add support for new 82599 device
Greg Rose (1):
ixgbevf: Fix namespace issue with ixgbe_write_eitr
John Fastabend (2):
ixgbe: fix RAR entry counting for generic and fdb_add()
ixgbe: remove extra unused queues in DCB + FCoE case
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix race condition in several network drivers when reading stats on 32bit
UP architectures. These drivers update their stats in a BH context and
therefore should use u64_stats_fetch_begin_bh/u64_stats_fetch_retry_bh
instead of u64_stats_fetch_begin/u64_stats_fetch_retry when reading the
stats.
Signed-off-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a previous patch to resolve issue with 82576 losing PHY setting
after PHY power down. However that previous implementation triggered speed
mismatch and occasional link lost. Now, this patch resolves both initial
PHY setting and speed mismatch issues.
Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can use 1TC DCB in the case of MSI and
legacy interrupts. The advantage to this is that it allows us to fully
support FCoE w/ DCB instead of having to drop to link flow control only
when using these interrupt modes.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for a new 82599 device that supports WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With DCB and FCoE configured extra queues may be allocated and
never used. After this patch we calculate the max correctly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Do RAR entry accounting correctly so that errors are reported and
promisc mode is set correctly when the number of entries exceeds
the hardware limits.
This can happen with many macvlan devices attached to the PF or
by adding many fdb entries in SR-IOV modes.
Also this includes a small refactor to fdb_add() to avoid having so
many nested if/else statements after adding a check for the number
or RAR entries.
The max entries for the PF is currently 16 we allow 15 additional
entries to account for the defined MAC.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so the function ixgbe_dcb_get_tc_from_up will use the
num_tcs.pg_tcs to determine the starting value for determining a traffic
class based on a user priority. The main motivation for this change is to
address possible bad configurations in which more TCs worth of data are
populated then there are actual TCs. By limiting this value we can at
least make certain we are not providing a map with values that are out of
range.
As a result any user priorities that are setup in the configuration with a
traffic class mapping higher than what the hardware supports will be
reported as being on TC 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The recent changes to netdev_alloc_skb actually make it so that the size of
the buffer now actually has a more direct input on the truesize. So in
order to make best use of the piece of a page we are allocated I am
reducing the IXGBE_RX_HDR_SIZE to 256 so that our truesize will be reduced
by 256 bytes as well.
This should result in performance improvements since the number of uses per
page should increase from 4 to 6 in the case of a 4K page. In addition we
should see socket performance improvements due to the truesize dropping
to less than 1K for buffers less than 256 bytes.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the function static to cleanup namespace.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can use the atr_sample_rate to determine if
we are capable of supporting ATR. The advantage to this approach is that it
allows us to now determine the setting of the IXGBE_FLAG_FDIR_HASH_CAPABLE
based on the queueing scheme, instead of the queueing scheme being based on
the flag.
Using this approach there are essentially 5 conditions that must be checked
prior to trying to enable ATR:
1. Is SR-IOV disabled?
2. Are the number of TCs <= 1?
3. Is RSS queueing limit greater than 1?
4. Is atr_sample_rate set?
5. Is Flow Director perfect filtering disabled?
If any of these conditions are enabled they should disable ATR filtering.
Note that in the case of conditions 1 through 4 being met we will set
things up for ATR queueing, however if test 5 fails we will still leave the
queues allocated for use by perfect filters. The reason for this is to
allow for us to switch back and forth between ntuple and ATR without
needing to reallocate the descriptor rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for handling IO errors and slot resets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds a spinlock around the mailbox accesses to prevent
simultaneous access to the mailboxes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does two things. First it drops the unnecessary work of
searching for enabled VFs when we first bring up the adapter and instead
just uses pci_num_vf to determine how many VFs are enabled on the adapter.
The second thing it does is drop the use of vfdev from the vf_data_storage
structure. Instead we just search the entire system for a VF that has us
as it's PF, and then if that VF is assigned we indicate that the VFs are
assigned. This allows us to still check for assigned VFs even if the
vfinfo allocation has failed, or vfinfo has been freed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is meant to fix a bug in which we were not checking for pre-existing
VFs if we were not setting the max_vfs value at driver load. What happens
now is that we always call ixgbe_enable_sriov and this checks for
pre-existing VFs ore requested VFs prior to deciding on no SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The replacement of spin_lock_irq/spin_unlock_irq pair in interrupt
handler by spin_lock_irqsave/spin_lock_irqrestore pair.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When io access mode is enabled by BOOTROM or BIOS for AR8152 v2.1,
the register can't be read/write by memory access mode.
Clearing Bit 8 of Register 0x21c could fixed the issue.
Signed-off-by: Cloud Ren <cjren@qca.qualcomm.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerr Kirsher says:
====================
This series contains updates to ixgbe.
...
Alexander Duyck (9):
ixgbe: Use VMDq offset to indicate the default pool
ixgbe: Fix memory leak when SR-IOV VFs are direct assigned
ixgbe: Drop references to deprecated pci_ DMA api and instead use
dma_ API
ixgbe: Cleanup configuration of FCoE registers
ixgbe: Merge all FCoE percpu values into a single structure
ixgbe: Make FCoE allocation and configuration closer to how rings
work
ixgbe: Correctly set SAN MAC RAR pool to default pool of PF
ixgbe: Only enable anti-spoof on VF pools
ixgbe: Enable FCoE FSO and CRC offloads based on CAPABLE instead of
ENABLED flag
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PCI_VENDOR_ID_INTEL from pci_ids.h instead of creating its own
vendor ID #define.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PCI_VENDOR_ID_INTEL from pci_ids.h instead of creating its own
vendor ID #define.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of only setting the FCOE segmentation offload and CRC offload flags
if we enable FCoE, we could just set them always since there are no
modifications needed to the hardware or adapter FCoE structure in order to
use these features.
The advantage to this is that if FCoE enablement fails, for example because
SR-IOV was enabled on 82599, we will still have use of the FCoE
segmentation offload and Tx/Rx CRC offloads which should still help to
improve the FCoE performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current logic is enabling anti-spoof on all pools and then clearing
anti-spoof on just the first PF pool. The correct approach is to only set
anti-spoof on the VF pools and to leave all of the PF pools unchecked.
This allows for items such as FCoE to use adjacent pools within the PF for
transmit and receive queues without the traffic being blocked by this
security feature.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change corrects an issue in which an FCoE enabled adapter was always
setting the FCoE SAN MAC MPSAR register to 0x1. This results in the first
VF being assigned the SAN MAC address in the case of SR-IOV and as such is
incorrect. To resolve this I am adding a new function that will update the
SAN MAC pool address after reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the behavior of the FCoE configuration so that it is
much closer to how the main body of the ixgbe driver works for ring
allocation.
The first piece is the ixgbe_fcoe_ddp_enable/disable calls. These allocate
the percpu values and if successful set the fcoe_ddp_xid value indicating
that we can support DDP.
The next piece is the ixgbe_setup/free_ddp_resources calls. These are
called on open/close and will allocate and free the DMA pools.
Finally ixgbe_configure_fcoe is now just register configuration. It can go
through and enable the registers for the FCoE redirection offload, and FIP
configuration without any interference from the DDP pool allocation.
The net result of all this is two fold. First it adds a certain amount of
exception handling. So for example if ixgbe_setup_fcoe_resources fails we
will actually generate an error in open and refuse to bring up the
interface.
Secondly it provides a much more graceful failure case than the previous
model which would skip setting up the registers for FCoE on failure to
allocate DDP resources leaving no Rx functionality enabled instead of just
disabling DDP.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change merges the 2 statistics values for noddp and noddp_ext_buff
and the dma_pool into a single structure that can be allocated per CPU.
The advantages to this are several fold. First we only need to do one
alloc_percpu call now instead of 3, so that means less overhead for
handling memory allocation failures. Secondly in the case of
ixgbe_fcoe_ddp_setup we only need to call get_cpu once which makes things a
bit cleaner since we can drop a put_cpu() from the exception path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so we always use the FCoE redirection table. We just
set all 8 entries to the same value in the case of only having one queue
for FCoE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The networking side of the code had already been updated to use dma_ calls
instead of the old pci_ calls. However it looks like the FCoE code was
never updated. This change goes through and moves everything from the pci
APIs to the dma APIs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF driver had a memory leak that would occur if VFs were assigned to a
guest. The amount of leak would vary with the number of VFs but could max
out at about 14K per PF. To reproduce the leak all you would need to do is
enable all the VFs on the first PF. Then start a loop of loading and
unloading the driver with max_vfs=63 for the first port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can use the VMDq ring feature offset value
to determine the default pool instead of using num_vfs. The reason for
this change is to avoid issues should we fail to allocate vfinfo but have
pre-existing VFs. What should happen in this case is that num_vfs will go
to 0, but the VMDq offset will contain the location of the first PF pool.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In its receive path, mlx4_en driver maps each page chunk that it pushes
to the hardware and unmaps it when pushing it up the stack. This limits
throughput to about 3Gbps on a Power7 8-core machine.
One solution is to map the entire allocated page at once. However, this
requires that we keep track of every page fragment we give to a
descriptor. We also need to work with the discipline that all fragments will
be released (in the sense that it will not be reused by the driver
anymore) in the order they are allocated to the driver.
This requires that we don't reuse any fragments, every single one of
them must be reallocated. We do that by releasing all the fragments that
are processed and only after finished processing the descriptors, we
start the refill.
We also must somehow guarantee that we either refill all fragments in a
descriptor or none at all, without resorting to giving up a page
fragment that we would have already given. Otherwise, we would break the
discipline of only releasing the fragments in the order they were
allocated.
This has passed page allocation fault injections (restricted to the
driver by using required-start and required-end) and device hotplug
while 16 TCP streams were able to deliver more than 9Gbps.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically allocated sysfs attributes must be initialized using
sysfs_attr_init(), otherwise lockdep complains:
BUG: key <address> not in .data!
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9ac32e1b firmware: convert e100 driver to request_firmware()
did a straight conversion of the in-driver ucode to external
files. This introduced the possibility of the driver failing
to enable an interface due to missing ucode. There was no
evaluation of the importance of the ucode at the time.
Based on comments in earlier versions of this driver, and in
the source code for the FreeBSD fxp driver, we can assume that
the ucode implements the "CPU Cycle Saver" feature on supported
adapters. Although generally wanted, this is an optional
feature. The ucode source is not available, preventing it from
being included in free distributions. This creates unnecessary
problems for the end users. Doing a network install based on a
free distribution installer requires the user to download and
insert the ucode into the installer.
Making the ucode optional when possible improves the user
experience and driver usability.
The ucode for some adapters include a bugfix, making it
essential. We continue to fail for these adapters unless the
ucode is available.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because there are multiple variants to the stmmac/dwmac driver, the
dts bindings should be updated to include version of the IP used.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb3 interface has a bad performance when VLAN is set. On my current
setup, a PowerLinux 7R2, I am able to get around 7 Gbps on a TCP_STREAM
(8 instances, 4k message).
With this patch, I am able to reach 9.5 Gbps.
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RFS infrastructure and flow steering in HW to keep CPU
affinity of rx interrupts and application per TCP stream.
A flow steering filter is added to the HW whenever the RFS
ndo callback is invoked by core networking code.
Because the invocation takes place in interrupt context, the
actual setup of HW is done using workqueue. Whenever new filter
is added, the driver checks for expiry of existing filters.
Since there's window in time between the point where the core
RFS code invoked the ndo callback, to the point where the HW
is configured from the workqueue context, the 2nd, 3rd etc
packets from that stream will cause the net core to invoke
the callback again and again.
To prevent inefficient/double configuration of the HW, the filters
are kept in a database which is indexed using hash function to enable
fast access.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable callers of mlx4_assign_eq to supply a pointer to cpu_rmap.
If supplied, the assigned IRQ is tracked using rmap infrastructure.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define this macro is one common place instead of duplicating it over the code
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is just meant to defragment the flags as there are several hole
that have been introduced since several features, or the flags for them,
have been removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All of our hardware supports RSS even if it is only for a single queue. So
instead of toting around the RSS enable flag I am updating the code so that
all devices are enabled and if we want to disable RSS it is indicated via
the RSS mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change essentially makes it so that we can enable almost all of the
features all at once. This patch allows for the combination of SR-IOV,
DCB, and FCoE in the case of the x540. It also beefs up the SR-IOV by
adding support for RSS to the PF.
The testing matrix gets to be very complex for this patch as there are a
number of different features and subsets for queueing options. I tried to
narrow these down a bit by restricting the PF to only supporting 4TC DCB
when it is enabled in addition to SR-IOV.
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change allows all pools from the default pool forward to be enabled vi
ixgbe_configure_virtualization. This is needed as we are planning to use
queues belonging to adjacent pools for FCoE when SR-IOV and FCoE are both
enabled.
In addition this patch contains some minor formatting changes as there were
a few spots that seemed to be in need of some cleanup.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbevf_get_ringparam we could run into a NULL pointer dereference
if the rings were not allocated when we attempted the call. To prevent
that we can just access the tx/rx_ring_count values instead of attempting
to access the rings to get the count.
This change corrects a memory leak and memory corruption in
ixgbevf_set_ringparam.
The memory leak was due to us not freeing the resources from the ring
before overwriting them. This change corrects the memory leak by making
certain to call ixgbe_free_tx/rx_resources on the rings prior to freeing
them.
The memory corruption was because we were replacing the rings but not
updating the q_vectors. It addresses the memory corruption by leaving the
rings in place and instead just copying the contents of the new rings into
the existing rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a good bit of redundancy between the Tx checksum and segmentation
offloads. In order to reduce some of this I am moving the code for
creating a context descriptor into a separate function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds the netdev to the ring structure. This allows for a
quicker transition from ring to netdev without having to go from ring to
adapter to netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver is going back one step from its' previous location before
bumping tail. This is incorrect. We should just be writing the value of
next_to_use into the tail register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have had an issue when using ixgbe+ixgbevf and 802.1 VLAN tagging.
When attaching a VLAN to a VF, frames with a 802.1q priority appeared
untagged on the VF hence not reaching the VLAN, where frames with
priority 0 where tagged as expected and seen by the VLAN device.
This seems due to the way ixgbevf is looking up the full tag
(prio+cfi+vlan) against the adapter active_vlans, as a condition to mark
the skb tagged.
Signed-off-by: Pascal Bouchareine <pascal@gandi.net>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original driver implementation assumed that for TSO, all the
payload data would be in the frags. This isn't always true; change
the driver to support payload data at skb->data between
"skb_transport_offset(skb) + tcp_hdrlen(skb)" and "skb->hdr_len",
followed by the data in the frags.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Enabling runtime PM support for davinci mdio driver
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the netpoll function to support netconsole. Tested and works
fine on my "JMC250 PCI Express Gigabit Ethernet Controller" (PCI ID 0250).
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add OF support for the davinci_emac driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: netdev@vger.kernel.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatoly Sivov <mm05@mail.ru>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The condition is always true so WOL will never work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should pull only ethernet header from page frag
to skb->head.
Pulling 64 bytes is too much for TCP (without options) on IPv4.
However, it makes sense to pull all the frame if it fits the
128 bytes bloc allocated for skb->head, to free one page per
small incoming frame.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: Yan-Pai Chen <yanpai.chen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 64 bit stats to Broadcom b44 ethernet driver.
Signed-off-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ability of driver to transmit packets depends on logical state
of the link. Ignore physical link status.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer FW has added new capability checks for VFs.
Driver should only use those capabilities which are allowed for VFs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerr Kirsher says:
====================
This series contains updates to ixgbe & ixgbevf.
...
Alexander Duyck (6):
ixgbe: Ping the VFs on link status change to trigger link change
ixgbe: Handle failures in the ixgbe_setup_rx/tx_resources calls
ixgbe: Move configuration of set_real_num_rx/tx_queues into open
ixgbe: Update the logic for ixgbe_cache_ring_dcb and DCB RSS
configuration
ixgbe: Cleanup logic for MRQC and MTQC configuration
ixgbevf: Update descriptor macros to accept pointers and drop _ADV
suffix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Francois Romieu says:
====================
Francois Romieu (1):
r8169: verbose error message.
Hayes Wang (1):
r8169: remove rtl_ocpdr_cond.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. Fix potential badness when running a self-test with SR-IOV enabled.
2. Fix calculation of some interface statistics that could run backward.
3. Miscellaneous cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the descriptor macros to accept pointers, updates the
name to drop the _ADV suffix, and include the IXGBEVF name in the macro.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to make the code much more readable for MTQC and MRQC
configuration.
The big change is that I simplified much of the logic so that we are
essentially handling just 4 cases and their variants. In the cases where
RSS is disabled we are actually just programming the RETA table with all
1s resulting in a single queue RSS. In the case of SR-IOV I am treating
that as a subset of VMDq. This all results int he following configuration
for the hardware:
DCB
En Dis
VMDq En VMDQ/DCB VMDq/RSS
Dis DCB/RSS RSS
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up some of the logic in an attempt to try and simplify
things for how we are configuring DCB w/ RSS.
In this patch I basically did 3 things. I updated the logic for getting
the first register index. I applied the fact that all TCs get the same
number of queues to simplify the looping logic in caching the DCB ring
register. Finally I updated how we configure the RQTC register to match
the fact that all TCs are assigned the same number of queues.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It makes much more sense for us to configure the real number of Tx and Rx
queues in the ixgbe_open call than it does in ixgbe_set_num_queues. By
setting the number in ixgbe_open we can avoid a number of unecessary
updates and only have to make the calls once.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we were exiting without cleaning up the memory internally on the
ixgbe_setup_rx_resources and ixgbe_setup_tx_resources calls. Instead of
forcing the caller to clean things up for us we should instead just unwind
the rings and free the memory as we go. This way we can more gracefully
clean up the rings in the event of an allocation failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the link status changes on the PF we need to notify the VFs. In order
to do this we should ping all of the VFs in order to trigger a link status
change on them as well.
This fixes issues in which the PF would reset, but the VF didn't because the
NAK flag was not set in the VF mailbox.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is not needed for mac_ocp_{write / read}. Actually bit 31 of OCPDR
does not change and r8168_mac_ocp_read always returns ~0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Tested-by: Francois Romieu <romieu@fr.zoreil.com>
Some interface statistics are computed in such a way that they can
sometimes decrease (and even underflow). Since the computed value
will never be greater than the true value, we fix this by only storing
the computed value when it increases.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently VF queues and drivers may remain active during this test.
This could cause memory corruption or spurious test failures.
Therefore we reset the port/function before running these tests on
Siena.
On Falcon this doesn't work: we have to do some additional
initialisation before some blocks will work again. So refactor the
reset/register-test sequence into an efx_nic_type method so
efx_selftest() doesn't have to consider such quirks.
In the process, fix another minor bug: Siena does not have an
'invisible' reset and the self-test currently fails to push the PHY
configuration after resetting. Passing RESET_TYPE_ALL to
efx_reset_{down,up}() fixes this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
