acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
XFER_SW_DMA_0 mode should be excluded from the extended cycle
timing computations.
[ This is just a documentation fix -- code inside the affected
'if' block already makes sure to accept only PIO modes. ]
Noticed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the current transfer speed
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Account for the requirements of the DMA mode currently used.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the current transfer speed
of the pair device on the port to determine PIO commmand timings used
for both devices on the port.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear UDMA enable bit also for PIO modes.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop depending on the BIOS setup.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop depending on the BIOS setup.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Account for the requirements of the other device on the port.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current PIO mode value instead of the physical maximum one
to determine the fastest allowed PIO for shared PIO/DMA timings.
Affected host drivers: amd74xx and via82cxxx.
[ Update comment to match -DaveM ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ->set_dma_mode method parameters to match ->set_dmamode method
used in struct ata_port_operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Change ->set_pio_mode method parameters to match ->set_piomode method
used in struct ata_port_operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dma_mode field to ide_drive_t matching dma_mode field used in
struct ata_device.
The validity of the field is restricted to ->dma_pio_mode method
only currently in IDE subsystem.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pio_mode field to ide_drive_t matching pio_mode field used in
struct ata_device.
The validity of the field is restricted to ->set_pio_mode method
only currently in IDE subsystem.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* preserve 80-wire cable detection bit
* don't clear UDMA settings when programming PIO/MWDMA modes
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commits 5955c7a and 7d948b1 for pata_via host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commit e4d866c for pata_via host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add custom struct ide_tp_ops instance to fix the internal bug of some VIA
chipsets which will reset the device register after changing the nIEN bit
in the device control register.
Based on commit bfce5e0 for pata_via host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add VIA_SATA_PATA flag for cx700, vx800 and vx855 chipsets
(the first port is SATA).
Based on commits 7585eb1, bfce5e0 and e4d866c for pata_via
host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commit e4d866c for pata_via host driver
(PCI ID was later changed by commit 5993856).
Update my credits while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove dead OSB4 UDMA support
* remove unreachable code
* make isa_dev local to ->init_chipset
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just use the standard ide_timing_compute() helper to calculate
PIO timings. This fixes many issues with the open-coded version
like using 16-bit timings when 8-bit ones should be used or not
accounting for the enhanced cycle time specified by the device.
Based on libata pata_cypress host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just use the standard ide_timing_compute() helper to calculate
PIO and MWDMA timings. This fixes some issues with the open-coded
version like allowing faster MWDMA timings than the ones required
by the current PIO mode or not accounting for the enhanced MWDMA
cycle time specified by the device.
Based on libata pata_cmd64x host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on libata pata_amd host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove leftover local_irq_[save,restore]() and FIXME note.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just use the standard ide_timing_compute() helper to calculate
PIO timings. This fixes many issues with the open-coded version
like potential recovery timings underclocking or not accounting
for the enhanced cycle time specified by the device.
Based on libata pata_ali host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ide_detach() called first ide_release() and then release_region(). This
produced the following warnings:
Trying to free nonexistent resource <000000000000c10e-000000000000c10e>
Trying to free nonexistent resource <000000000000c100-000000000000c107>
This is true, because the callchain inside ide_release() is:
ide_release -> pcmcia_disable_device -> pcmcia_release_io
So, the whole io-block is already gone for release_region(). To fix
this, just swap the order of releasing (and remove the now obsolete
shadowing).
bzolnier:
- release resources in ide_release() to fix ordering of events
- remove stale FIXME note while at it
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ready to get everything using unlocked_ioctl()
For ide_tape we just push down as this is legacy code anyway
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Sun, Jan 03, 2010 at 12:23:14AM +0000, Russell King wrote:
> - with IDE
> - locks the interrupt line, and makes the machine extremely painful -
> about an hour to get to the point of being able to unload the
> pdc202xx_old module.
Having manually bisected kernel versions, I've narrowed it down to some
change between 2.6.30 and 2.6.31. There's not much which has changed
between the two kernels, but one change stands out like a sore thumb:
+static int pdc202xx_test_irq(ide_hwif_t *hwif)
+{
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ unsigned long high_16 = pci_resource_start(dev, 4);
+ u8 sc1d = inb(high_16 + 0x1d);
+
+ if (hwif->channel) {
+ /*
+ * bit 7: error, bit 6: interrupting,
+ * bit 5: FIFO full, bit 4: FIFO empty
+ */
+ return ((sc1d & 0x50) == 0x40) ? 1 : 0;
+ } else {
+ /*
+ * bit 3: error, bit 2: interrupting,
+ * bit 1: FIFO full, bit 0: FIFO empty
+ */
+ return ((sc1d & 0x05) == 0x04) ? 1 : 0;
+ }
+}
Reading the (documented as a 32-bit) system control register when the
interface is idle gives: 0x01da110c
So, the byte at 0x1d is 0x11, which is documented as meaning that the
primary and secondary FIFOs are empty.
The code above, which is trying to see whether an IRQ is pending, checks
for the IRQ bit to be one, and the FIFO bit to be zero - or in English,
to be non-empty.
Since during a BM-DMA read, the FIFOs will naturally be drained to the
PCI bus, the chance of us getting to the interface before this happens
are extremely small - and if we don't, it means we decide not to service
the interrupt. Hence, the screaming interrupt problem with drivers/ide.
Fix this by only indicating an interrupt is ready if both the interrupt
and FIFO empty bits are at '1'.
This bug only affects PDC20246/PDC20247 (Promise Ultra33) based cards,
and has been tested on 2.6.31 and 2.6.33-rc2.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring back ->maskproc method since it is still needed for proper operation,
as noticed by Russell King:
> This change is bogus.
>
> writeb(0, base + ICS_ARCIN_V6_INTROFFSET_1);
> readb(base + ICS_ARCIN_V6_INTROFFSET_2);
>
> writeb(0, base + ICS_ARCIN_V6_INTROFFSET_2);
> readb(base + ICS_ARCIN_V6_INTROFFSET_1);
>
> This sequence of code does:
>
> 1. enable interrupt 1
> 2. disable interrupt 2
> 3. enable interrupt 2
> 4. disable interrupt 1
>
> which results in the interrupt for the second channel being enabled -
> leaving channel 1 blocked.
>
> Firstly, icside shares its two IDE channels with one DMA engine - so it's
> a simplex interface. IDE supports those (or did when the code was written)
> serializing requests between the two interfaces. libata does not.
>
> Secondly, the interrupt lines on icside float when there's no drive connected
> or when the drive has its NIEN bit set, which means that you get spurious
> screaming interrupts which can kill off all expansion card interrupts on
> the machine unless you disable the channel interrupt on the card.
>
> Since libata can not serialize the operation of the two channels like IDE
> can, the libata version of the icside driver does not contain the interrupt
> stearing logic. Instead, it looks at the status after reset, and if
> nothing was found on that channel, it masks the interrupt from that
> channel.
This patch reverts changes done in commit dff8817 (I became confused due to
non-standard & undocumented ->maskproc method, anyway sorry about that).
Noticed-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
scc_pata host driver predated module unloading support for IDE host
drivers so even though it supports PCI hot-unplug and implements
PCI device ->remove method it doesn't allow module removal. Fix it.
Add missing __init/__exit tags to module_init/module_exit functions
while at it (from Peter Huewe).
Noticed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6:
sl82c105: remove no longer needed debugging code
sis5513: remove stale TODO
pdc202xx_old: remove no longer needed debugging code
cy82c693: remove no longer needed debugging code
cmd64x: remove no longer needed debugging code
alim15x3: remove obsolete and dangerous wdc_udma parameter
ide: Increase WAIT_DRQ to accomodate some CF cards and SSD drives.
cs5535: add pci id for AMD based CS5535 controllers
slc90e66: fix UDMA handling
drivers/ide/tx4938ide.c: use resource_size()
drivers/ide/ide_platform.c: use resource_size()
drivers/ide/au1xxx-ide.c: use resource_size()
hpt366: remove dead old timing tables
ide: update Kconfig text to mark as deprecated
ide-tape: remove the BKL
hpt366: kill unused #define's
The hotplug mediabay has tendrils deep into drivers/ide code
which makes a libata port reather difficult. In addition it's
ugly and could be done better.
This reworks the interface between the mediabay and the rest
of the world so that:
- Any macio_driver can now have a mediabay_event callback
which will be called when that driver sits on a mediabay and
it's been either plugged or unplugged. The device type is
passed as an argument. We can now move all the IDE cruft
into the IDE driver itself
- A check_media_bay() function can be used to take a peek
at the type of device currently in the bay if any, a cleaner
variant of the previous function with the same name.
- A pair of lock/unlock functions are exposed to allow the
IDE driver to block the hotplug callbacks during the initial
setup and probing of the bay in order to avoid nasty race
conditions.
- The mediabay code no longer needs to spin on the status
register of the IDE interface when it detects an IDE device,
this is done just fine by the IDE code itself
Overall, less code, simpler, and allows for another driver
than our old drivers/ide based one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.
As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Based on commit 02cb009 for pata_cs5530.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checking of the currently programmed UDMA mode.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Currently, ide_cmd_ioctl when invoked for setting DMA transfer mode calls
ide_find_dma_mode with requested mode as XFER_UDMA_6. This prevents setting DMA
mode to any other value than the default (maximum) supported by the device (or
UDMA6, if supported) irrespective of the actual requested transfer mode and
returns error.
For example, setting mode to UDMA2 using hdparm, where UDMA4 is the default
transfer mode gives following error:
# ./hdparm -d1 -Xudma2 /dev/hda
/dev/hda:hda: UDMA/66 mode selected
setting using_dma to 1 (on)
hda: UDMA/66 mode selected
setting xfermode to 66 (UltraDMA mode2)
HDIO_DRIVE_CMD(setxfermode) failed: Invalid argument
using_dma = 1 (on)
This patch fixes the issue.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size() for devm_request_mem_region.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size() for devm_{ioremap/io_port_map}.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size() for {request/release}_mem_region and ioremap.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been enough time since introduction of the new timing tables
(commit 809b53c from Dec 12 2007) and the old timing tables are still
available in pata_hpt37x.c (or git history) if somebody needs them.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ide-cs.c is the only PCMCIA device driver making use of CONFIG_PCMCIA_DEBUG,
so convert it to use the dynamic debug infrastructure.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This reverts commit 6029336426.
Ok, we really do need to revert this, even with Bart's sis5513.c
fix in there.
The problem is that several driver's ->set_pio_mode() method
depends upon the drive->media type being set properly. Most
of them use this to enable prefetching, which can only be done
for disk media.
But the commit being reverted here calls ->set_pio_mode() before
it's setup. Actually it considers everything disk because that
is the default media type set by ide_port_init_devices_data().
The set of drivers that depend upon the media type in their
->set_pio_method() are:
drivers/ide/alim15x3.c
drivers/ide/it8172.c
drivers/ide/it8213.c
drivers/ide/pdc202xx_old.c
drivers/ide/piix.c
drivers/ide/qd65xx.c
drivers/ide/sis5513.c
drivers/ide/slc90e66.c
And it is possible that we could fix this by guarding the prefetching
and other media dependent setting changes with a test on
IDE_PFLAG_PROBING in hwif->port_flags, that's simply too risky for
2.6.32-rcX and -stable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current Kconfig text for CONFIG_IDE doesn't give a hint to users that this
subsystem is currently in maintenance mode and isn't actively developed.
Let's correct this by marking it as deprecated, and also get rid of a bunch of
unnecessary text that doesn't really have anything to do with what the option is
for.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the BKL calls in the chrdev_{open,release} interfaces with a
simple sleeping mutex.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two have been long unused but I've just noticed...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is
connected to one of the channels.
Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3.
/dev/hda is 8GB Seagate ST38410A in MWDMA2
/dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2
- When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda
are corrupted, there are twiddled single bits 1->0 and some full 32-bit
words corrupted, sometimes commands fail (which switches /dev/hda to
PIO mode but the corruptions happen even in PIO).
- Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine).
- When I connected normal rotating harddisk to /dev/hdd, there was no
corruption, so the corruption is something specific to SSD.
- I tried the same setup on a PCI card with CMD649 and saw no corruption.
This patch serializes the operation for CMD646 and 643 (I didn't test
CMD643 but it may have the same hw bug too because it's earlier design).
CMD649 is good. I don't know anything about CMD 648.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
Revert "Revert "ide: try to use PIO Mode 0 during probe if possible""
sis5513: fix PIO setup for ATAPI devices
This reverts commit 24df31acaf.
The root cause of reported system hangs was (now fixed) sis5513 bug
and not "ide: try to use PIO Mode 0 during probe if possible" change
(commit 6029336426) so the revert was
incorrect (it simply replaced one regression with the other one).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear prefetch setting before potentially (re-)enabling it in
config_drive_art_rwp() so the transition of the device type on
the port from ATA to ATAPI (i.e. during warm-plug operation)
is handled correctly.
This is a really old bug (it probably goes back to very early
days of the driver) but it was only affecting warm-plug operation
until the recent "ide: try to use PIO Mode 0 during probe if
possible" change (commit 6029336426).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: David Fries <david@fries.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6029336426.
Based upon a report by David Fries, wherein his system hangs
on bootup with sis5513 controller, right after the CDROM
is registered by ide-cd.c and the TOC is first read.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (119 commits)
ACPI: don't pass handle for fixed hardware notifications
ACPI: remove null pointer checks in deferred execution path
ACPI: simplify deferred execution path
acerhdf: additional BIOS versions
acerhdf: convert to dev_pm_ops
acerhdf: fix fan control for AOA150 model
thermal: add missing Kconfig dependency
acpi: switch /proc/acpi/{debug_layer,debug_level} to seq_file
hp-wmi: fix rfkill memory leak on unload
ACPI: remove unnecessary #ifdef CONFIG_DMI
ACPI: linux/acpi.h should not include linux/dmi.h
hwmon driver for ACPI 4.0 power meters
topstar-laptop: add new driver for hotkeys support on Topstar N01
thinkpad_acpi: fix rfkill memory leak on unload
thinkpad-acpi: report brightness events when required
thinkpad-acpi: don't poll by default any of the reserved hotkeys
thinkpad-acpi: Fix procfs hotkey reset command
thinkpad-acpi: deprecate hotkey_bios_mask
thinkpad-acpi: hotkey poll fixes
thinkpad-acpi: be more strict when detecting a ThinkPad
...
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6:
ide: fixup for fujitsu disk
ide: convert to ->proc_fops
at91_ide: remove headers specific for at91sam9263
IDE: palm_bk3710: convert clock usage after clkdev conversion
ide: fix races in handling of user-space SET XFER commands
ide: allow ide_dev_read_id() to be called from the IRQ context
ide: ide-taskfile.c fix style problems
drivers/ide/ide-cd.c: Use DIV_ROUND_CLOSEST
ide-tape: fix handling of postponed rqs
ide-tape: convert to ide_debug_log macro
ide-tape: fix debug call
ide: Fix annoying warning in ide_pio_bytes().
IDE: Save a call to PageHighMem()
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (25 commits)
pata_rz1000: use printk_once
ahci: kill @force_restart and refine CLO for ahci_kick_engine()
pata_cs5535: add pci id for AMD based CS5535 controllers
ahci: Add AMD SB900 SATA/IDE controller device IDs
drivers/ata: use resource_size
sata_fsl: Defer non-ncq commands when ncq commands active
libata: add SATA PMP revision information for spec 1.2
libata: fix off-by-one error in ata_tf_read_block()
ahci: Gigabyte GA-MA69VM-S2 can't do 64bit DMA
ahci: make ahci_asus_m2a_vm_32bit_only() quirk more generic
dmi: extend dmi_get_year() to dmi_get_date()
dmi: fix date handling in dmi_get_year()
libata: unbreak TPM filtering by reorganizing ata_scsi_pass_thru()
sata_sis: convert to slave_link
sata_sil24: always set protocol override for non-ATAPI data commands
libata: Export AHCI capabilities
libata: Delegate nonrot flag setting to SCSI
[libata] Add pata_rdc driver for RDC ATA devices
drivers/ata: Remove unnecessary semicolons
libata: remove spindown skipping and warning
...
->read_proc, ->write_proc are going away, ->proc_fops should be used instead.
The only tricky place is IDENTIFY handling: if for some reason
taskfile_lib_get_identify() fails, buffer _is_ changed and at least
first byte is overwritten. Emulate old behaviour with returning
that first byte to userspace and reporting length=1 despite overall -E.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver requires only static memory controller definitions and macroses
contained in generic header at91sam9_smc.h.
Those extra headers are misleading since this driver also works fine for
at91sam9260 SoC: tests were performed on afeb9260 board.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaVinci core code has converted to the new clkdev API so
clock name strings are not needed. Instead, just the a
'struct device' pointer is needed.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
