On spear320 device supported mode are:
* AUTO_NET_SMII_MODE
* AUTO_NET_MII_MODE
* AUTO_EXP_MODE
* SMALL_PRINTERS_MODE
* EXTENDED_MODE
spear320-evb board is designed for EXTENDED_MODE only, hence it does not
boot correctly in current form where pinctrl part for some devices fail.
Configure and boot the SPEAr320 evaluation board in EXTENDED_MODE.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
From Lee Jones <lee.jones@linaro.org>:
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Remove PMU platform registration when booting with DT
ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure
ARM: ux500: Ensure vendor specific properties have the vendor's identifier
pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes
ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled
ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices
ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree
ARM: ux500: Apply ab8500-debug node do the db8500 DT structure
ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices
ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm
ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl
ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT
ARM: ux500: Enable LED heartbeat functionality on Snowball
ARM: ux500: Add support for input/ponkey into the db8500's Device Tree
ARM: ux500: Add a ab8500-gpadc node to the db8500 Device Tree
ARM: ux500: Enable the user LED on Snowball via Device Tree
ARM: ux500: Kconfig: Compile in leds-gpio support for Snowball
ARM: ux500: Provide auxdata to be used as name base clock search for nmk-i2c
ARM: ux500: Remove unused i2c platform_data initialisation code
ARM: ux500: Enable Device Tree support mmci for Snowball
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bindings for DMA channels are still under discussion and will
change once this has been resolved. Therefore we mark them
the newly added ones as preliminary. Let's hope nobody starts
relying on them...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Kukjin Kim <kgene.kim@samsung.com>:
It is for supporting spi dt for exynos4210 and exynos5250, and got the
ack from Grant Likely for spi driver.
Note: Since this is including spi driver changes, so it was made based
on next/devel-dma-ops which touches same file, Samsung spi driver for
avoiding bad conflicts.
* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
ARM: EXYNOS: Add spi clock support for EXYNOS5
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
ARM: EXYNOS: Add device tree node for EXYNOS4 interrupt combiner controller
spi: s3c64xx: add device tree support
spi: s3c64xx: Remove the 'set_level' callback from controller data
ARM: SAMSUNG: Modify s3c64xx_spi{0|1|2}_set_platdata function
ARM: SAMSUNG: Remove pdev pointer parameter from spi gpio setup functions
spi: s3c64xx: move controller information into driver data
spi: s3c64xx: remove unused S3C64XX_SPI_ST_TRLCNTZ macro
ARM: S3C64XX: Add a new dma request id for device tree based dma channel lookup
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some mxc processors have an edge_sel feature, which allows the IRQ to be
triggered by any edge.
This patch makes use of this feature if available, which skips mxc_flip_edge().
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device nodes for the three instances of spi controllers in
EXYNOS5 platforms and enable instance SPI 1 for SMDK5250 board.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add device nodes for the three instances of spi controllers in
EXYNOS4 platforms. Enable instance SPI 2 for SMDKV310 board and
disable all spi instances for Origen board.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Device Tree file for the CoreTile Express
A15x2 A7x3 (V2P-CA15_CA7).
Note that the A7 cpu nodes are commented out, as the
big.LITTLE-relevant patches are not upstreamed yet. Till
this time one can use the board with two A15 cores only,
keeping the A7s in reset by adding the following setting
to the board.txt file in Versatile Express configuration
tree:
SCC: 0x018 0x00001FFF
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
SMSC driver requires "vdd33a" and "vddvario" regulator supplies now.
Add fixed regulator describing 3V3 power line (in both motherboard's
Device Trees and the non-DT code) and force fixed regulator config
option if regulators framework is enabled.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This patch configures the I2C bus timing registers according
to information passed via DT. Currently, 100kHz and 400kHz
modes are supported.
The TIMING2 register value is wrong in the documentation for
i.MX28! This was found and fixed by:
Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Any non-standard property should contain the vendor's identifier which
should be perpended onto the property name followed by a comma. This
aids in name-space collision prevention.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During a Device Tree boot, all probing will now be completed on parse
of the Device Tree binary. In the same patch we remove platform
registration of the Real Time Clock.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add a node for the AB8500 Real Time Clock in all devices
supporting the DB8500. The AB8500 RTC driver makes use of named
interrupts we provide support for this too.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AB8500 driver has now been provided with IRQ domain support. This
means we can request IRQs from any of it's uses via Device Tree. This
patch advertises the AB8500 as an Interrupt Controller and provides the
correct calls in the format the driver expects.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This node has no properties. It merely allows probing of the
ab8500-debugfs driver during Device Tree initialisation.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we specify each of the ab8500 USB driver's seven IRQs, which the
driver references by name. We also apply regulator support for the
three used by the device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the DT node for the misc/ab8500-pwm driver. It will
allow probing of the driver during a Device Tree enabled boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the DT node for the mfd/ab8500-sysctrl driver. It will
allow probing of the driver during a Device Tree enabled boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch configures the user LED on Snowball to double flash
every second or so, whilst it's still alive. This can give key
indications as to what the board is doing in the case of no
console output.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch provides support for the ab8500-gpadc driver.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch enables and illuminates the user_led on the
Snowball low-cost development board using DT. It also
removes initialisation carried out from platform code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow proper initialisation for MMC via the mmci driver
for the Snowball low-cost development board using DT. At
the moment we continue to use DMA setup from platform code.
Once the DMA generic DT bindings have been completed we
can then port the remainder over to DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add node for EXYNOS4 interrupt combiner controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Shawn Guo <shawn.guo@linaro.org>:
Here is the second (last) batch of mxs mxs device tree changes for 3.6.
* 'mxs/dt-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx28-evk: add usb devices
ARM: mxs: rename dts files with soc name being the prefix
ARM: apx4devkit: add pin muxing for GPIOs
ARM: apx4devkit: remove AUART3
ARM: apx4devkit: add SSP2 support
ARM: apx4devkit: fix the bus-width of SSP0 to 4 bits
ARM: apx4devkit: add display support
ARM: apx4devkit: add NAND support
ARM: mxs: add dtb-y target into Makefile.boot
ARM: mxs: convert stmp378x_devb board to device tree
ARM: mxs: convert tx28 board to device tree
ARM: mxs: convert apx4devkit board to device tree
ARM: mxs: convert m28evk board to device tree
ARM: dts: imx28: move lcdif control pins into board dts
ARM: dts: imx28: move extra gpmi-nand pins into board dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Shawn Guo <shawn.guo@linaro.org>:
Here is the second (last) batch of imx device tree changes for 3.6.
* 'imx/dt-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: ensure ANATOP controller is available
ARM: dts: imx6q-sabrelite: add ecspi1 pinctrl support
ARM: dts: imx6q-sabrelite: add usb devices
ARM: imx6q: disable usb charger detector
ARM: imx6q: add usbphy clocks
ARM: imx6q: add usb controller clock lookups
ARM: dts: imx: update #interrupt-cells for gpio nodes
bindings: update imx and mxs #gpio-cells
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX dt updates for v3.6
* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
arm/dts: Add support for i.MX31 bug 1.x board from buglabs.
ARM i.MX31: Add devicetree support
ARM: dts: Add basic support for mx27_3ds board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Tony Lindgren <tony@atomide.com>:
Device tree related patches for omaps
* tag 'omap-devel-dt-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: New dts file for PandaBoardES (4460)
arm/dts: omap4-panda: Audio support for PandaBoard 4430
arm/dts: omap4-sdp: Enable audio support via device tree
arm/dts: omap4-sdp: Add support for twl6040
arm/dts: omap4-sdp: Add fixed regulator to represent VBAT
arm/dts: omap4: Add entry for OMAP DMIC IP
arm/dts: omap4: Add entry for OMAP McPDM IP
arm/dts: am33xx wdt node
arm/dts: remove MMC/SD and SPI related entries from am33xx.dtsi
watchdog: omap_wdt: add device tree support
ARM: OMAP: avoid build wdt platform device if with dt support
arm/dts: add wdt node for omap3 and omap4
arm/dts: OMAP4: Add Variscite OMAP4 System-On-Modeule support
arm/dts: Add support for AM335x BeagleBone
arm/dts: Add support for AM335x EVM
arm/dts: Add initial DT support for AM33XX SoC family
arm/dts: omap3-evm: Add i2c and twl4030 support
arm/dts: Add support for TI AM3517/05 EVM board
arm/dts: OMAP2: Add support for OMAP2420H4 Board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Nicolas Ferre <nicolas.ferre@atmel.com>:
Two new boards described with device tree
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: Add support for board aks-cdu
ARM: at91: add support for Telit EVK-PRO3 with Telit GE863-PRO3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch contains changes to Tegra device tree files, and related
Kconfig and Makefile changes. Highlights are:
* New support for the Whistler board.
* Use of the I2C pinctrl-based bus mux on Seaboard/Springbank.
This branch is based on Tegra's for-3.6/cleanup branch from a previous
pull request.
* 'for-3.6/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra seaboard: move battery monitor to mux'd I2C bus.
ARM: dt: tegra: seaboard: instantiate pinctrl-based I2C bus mux
ARM: dt: tegra: add Whistler device tree file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Imx6q sabrelite board uses ecspi1 to connect a spi flash sst25vf016b,
we need to add pinctrl information for it in the dts, otherwise the
ecspi1 driver can't work and the connected flash is wrongly
detected as a mr25h256 flash like this:
m25p80 spi32766.0: found mr25h256, expected sst25vf016b
m25p80 spi32766.0: mr25h256 (32 Kbytes)
Cc: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds real clock support to Calxeda Highbank SOC using the common
clock infrastructure.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[mturquette@linaro.org: fixed up invalid writes to const struct member]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Rename mxs dts files with soc name being the prefix, so that the board
dts file can be located easily by soc name, and we also gain the
consistency of naming.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
AUART3 is not available anymore. Pins are used as GPIOs.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add HannStar display and device tree configuration.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The enc28j60 spi device does not get converted to dts file, because
there is no mxs spi driver on mainline so far. The enc28j60 spi
in mach-stmp378x_devb.c does not work anyway.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
FEC support is missing because we need to find a proper way to rewrite
tx28_add_fec0 for device tree boot.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The presence and muxing of lcdif control pins can vary much on different
boards. Move them into imx28-evk.dts to make lcdif_24bit_pins_a only
about data pins, so that it can be reused by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Only pins GPMI_CE0N and GPMI_READY0 are generally used by other boards.
Move GPMI_CE1N and GPMI_READY1 into imx28-evk.dts to make gpmi_pins_a
more general, and can be used by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Only the main UART and the memory node information are added.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic devicetree support for i.MX31 based SoCs.
Only the UART and interrupts bindings are added.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
From Tony Lindgren <tony@atomide.com>:
This branch contains minimal support for omap5 to boot to a
console without clock framework support. This branch depends
on omap-cleanup-part2-for-v3.6.
* 'devel-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
ARM: OMAP5: timer: Add clocksource, clockevent support
ARM: OMAP5: Add minimal support for OMAP5430 SOC
ARM: OMAP5: id: Add cpu id for ES versions
ARM: OMAP: counter-32k: Select the CR register offset using the IP scheme
ARM: OMAP2+: Move stubbed secure_sram_reserve function to a common.c and call it __weak
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[ben.dooks@codethink.co.uk: ensure error check on of_property_read_u32]
[ben.dooks@codethink.co.uk: use mpic address instead of bus-unit's ]
[ben.dooks@codethink.co.uk: BUG_ON() if the of_iomap() fails for mpic]
[ben.dooks@codethink.co.uk: move mpic per-cpu register base ]
[ben.dooks@codethink.co.uk: number fetch should use irqd_to_hwirq()]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Add support for our "aks-cdu" board based up on Telit's module GE863 Pro3.
It has more uarts, leds, another nand partitioning.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[nicolas.ferre@atmel.com: correction of the dts file]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch allows the ATAG_CMDLINE provided by the bootloader to be
concatenated to the bootargs property of the device tree.
This is useful to merge static values defined in the device tree
with the boot loader's (possibly) more dynamic values, such as
startup reasons and more.
The bootloader should use the device tree to pass those values to
the kernel, but that's not always simple (old bootloader or very
small one).
The behaviour is the same as the one introduced by Victor Boivie in
4394c12442 by extending the CONFIG_CMDLINE.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding the minimum device tree files required for
OMAP5 to boot.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The 4430 and 4460 version of PandaBoard mostly the same with
exception at least in audio setup.
Use the omap4-panda.dts file as a base and only override the differences
between the revisions.
For audio it is the name of the sound card and the routing information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PandaBoard uses twl6040 connected via McPDM for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 SDP the audio setup includes the twl6040 codec and digital
microphones.
Since OMAP4 SDP is a reference board it has all possible audio interfaces
connected. This information is passed via the ti,audio-routing
property.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The twl6040 provides the audio and vibra support on OMAP4 SDP boards.
It is connected to i2c1 bus with 0x4b address.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DMIC IP is used to connect up to 6 digital microphones directly to OMAP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM is used on OMAP4 based boards to communicate with an external audio
codec (twl6040).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC/SD and SPI entries in this file are not tested yet. They
inadvertently came into the patch because of some work in progress
stuff I had in my repo.
These entries should not have been sent out in the first place and
I am sorry for the trouble and will be extra careful in future.
Since the offending commit is not sent upstream yet, I hope this can
be merged into the commit 5fc0b42a98
(arm/dts: Add initial DT support for AM33XX SoC family) on the devel-dt
branch of linux-omap tree.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a very basic dt support for mx27_3ds (also known as mx27pdk).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Change the value of #interrupt-cells of gpio nodes from 1 to 2, so that
the gpio irq type can be specified in device tree. Also update binding
document to make it clear.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add generic DT board support for the sh7377 SoC.
SCIF serial ports and timers are kept as regular
platform devices. Other on-chip and on-board devices
should be configured via the device tree.
At this point there is no interrupt controller support
in place but such code will be added over time when
proper IRQ domain support has been added to INTC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add generic DT board support for the r8a7740 SoC.
SCIF serial ports and timers are kept as regular
platform devices. Other on-chip and on-board devices
should be configured via the device tree.
At this point there is no interrupt controller support
in place but such code will be added over time when
proper IRQ domain support has been added to INTC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tegra's I2C2 controller can be routed to either the PTA or DDC pin group
on Seaboard. Define the pinctrl state nodes required to allow runtime
control of this routing. Instantiate a pinctrl-i2cmux I2C bus mux that
uses these pinctrl states.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
mx23-olinuxino is a low cost board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Device's regulator matches their hardware counterparts with the
property "regulator-compatible" of each child regulator node in
place of the child node name.
Add the property "regulator-compatible" for each regulator with
their hardware counterpart's name.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add Variscite OMAP4 System-On-Modeule support
Signed-off-by: Uri Yosef <uri.y@variscite.com>
[tony@atomide.com: updated to use disabled instead of disable]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM335X BeagleBone device tree source (am335x-evm.dts) file
to use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM335X EVM device tree source (am335x-evm.dts) file to
use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree source include file for the AM33XX SoC family.
An additional .dtsi file is created to describe the generic
AM33XX CPU module like intc, ocp.
Actual selection of available peripherals is handled in seperate
.dts files using this am33xx.dtsi generic header file.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing properties for fec, phy-supply, phy-reset-gpios and
phy-reset-duration, which are required by fec driver for successfully
probe fec from device tree, if bootloader hasn't set those things up.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add vmmc-supply for mmc device, so that the power to mmc slot can be
turned on by mmc driver if bootloader hasn't done it.
Also remove "okay" status for mmc1/ssp1, as the device has pin conflict
with gpmi-nand. Actually the device is already disabled since the
mxs-mmc driver adopts pinctrl support because there is no pinctrl setup
for the device in dts. Make this explicit by removing "okay" status.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
