The CPSW switch can act as Dual EMAC by segregating the switch ports
using VLAN and port VLAN as per the TRM description in
14.3.2.10.2 Dual Mac Mode
Following CPSW components will be common for both the interfaces.
* Interrupt source is common for both eth interfaces
* Interrupt pacing is common for both interfaces
* Hardware statistics is common for all the ports
* CPDMA is common for both eth interface
* CPTS is common for both the interface and it should not be enabled on
both the interface as timestamping information doesn't contain port
information.
Constrains
* Reserved VID of One port should not be used in other interface which will
enable switching functionality
* Same VID must not be used in both the interface which will enable switching
functionality
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP Appropriate Byte Count was added by me, but later disabled.
There is no point in maintaining it since it is a potential source
of bugs and Linux already implements other better window protection
heuristics.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently refactored the driver source, this patch will take care of
updating copyright date and adding it to newly added files.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Ingo Molnar:
"Three small fixlets"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel/cacheinfo: Shut up annoying warning
x86, doc: Boot protocol 2.12 is in 3.8
x86-64: Replace left over sti/cli in ia32 audit exit code
Pull two small RCU fixlets from Ingo Molnar.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make rcu_nocb_poll an early_param instead of module_param
rcu: Prevent soft-lockup complaints about no-CBs CPUs
The original suggestion to delete wanrouter started earlier
with the mainline commit f0d1b3c2bc
("net/wanrouter: Deprecate and schedule for removal") in May 2012.
More importantly, Dan Carpenter found[1] that the driver had a
fundamental breakage introduced back in 2008, with commit
7be6065b39 ("netdevice wanrouter: Convert directly reference of
netdev->priv"). So we know with certainty that the code hasn't been
used by anyone willing to at least take the effort to send an e-mail
report of breakage for at least 4 years.
This commit does a decouple of the wanrouter subsystem, by going
after the Makefile/Kconfig and similar files, so that these mainline
files that we are keeping do not have the big wanrouter file/driver
deletion commit tied into their history.
Once this commit is in place, we then can remove the obsolete cyclomx
drivers and similar that have a dependency on CONFIG_WAN_ROUTER_DRIVERS.
[1] http://www.spinics.net/lists/netdev/msg218670.html
Originally-by: Joe Perches <joe@perches.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
PullHID fixes from Jiri Kosina:
- fix i2c-hid and hidraw interaction, by Benjamin Tissoires
- a quirk to make a particular device (Formosa IR receiver) work
properly, by Nicholas Santos
* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: fix i2c_hid_output_raw_report
HID: usbhid: quirk for Formosa IR receiver
HID: remove x bit from sensor doc
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
dmraid assess redundancy and replacements slightly inaccurately which
could lead to some degraded arrays failing to assemble.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=bJyL
-----END PGP SIGNATURE-----
Merge tag 'md-3.8-fixes' of git://neil.brown.name/md
Pull dmraid fix from NeilBrown:
"Just one fix for md in 3.8
dmraid assess redundancy and replacements slightly inaccurately which
could lead to some degraded arrays failing to assemble."
* tag 'md-3.8-fixes' of git://neil.brown.name/md:
DM-RAID: Fix RAID10's check for sufficient redundancy
Define the 2.12 bzImage boot protocol: add xloadflags and additional
fields to allow the command line, initramfs and struct boot_params to
live above the 4 GiB mark.
The xloadflags now communicates if this is a 64-bit kernel with the
legacy 64-bit entry point and which of the EFI handover entry points
are supported.
Avoid adding new read flags to loadflags because of claimed
bootloaders testing the whole byte for == 1 to determine bzImageness
at least until the issue can be researched further.
This is based on patches by Yinghai Lu and David Woodhouse.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Originally-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Pablo Neira Ayuso says:
====================
This batch contains netfilter updates for you net-next tree, they are:
* The new connlabel extension for x_tables, that allows us to attach
labels to each conntrack flow. The kernel implementation uses a
bitmask and there's a file in user-space that maps the bits with the
corresponding string for each existing label. By now, you can attach
up to 128 overlapping labels. From Florian Westphal.
* A new round of improvements for the netns support for conntrack.
Gao feng has moved many of the initialization code of each module
of the netns init path. He also made several code refactoring, that
code looks cleaner to me now.
* Added documentation for all possible tweaks for nf_conntrack via
sysctl, from Jiri Pirko.
* Cisco 7941/7945 IP phone support for our SIP conntrack helper,
from Kevin Cernekee.
* Missing header file in the snmp helper, from Stephen Hemminger.
* Finally, a couple of fixes to resolve minor issues with these
changes, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's a long-pending fixes pull request for arm-soc (I didn't send one
in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted to
multiplatform on i.MX, which was causing build failures when included
- Device tree updates for at91 dealing mostly with their new
pinctrl setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YDHs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
Before attempting to activate a RAID array, it is checked for sufficient
redundancy. That is, we make sure that there are not too many failed
devices - or devices specified for rebuild - to undermine our ability to
activate the array. The current code performs this check twice - once to
ensure there were not too many devices specified for rebuild by the user
('validate_rebuild_devices') and again after possibly experiencing a failure
to read the superblock ('analyse_superblocks'). Neither of these checks are
sufficient. The first check is done properly but with insufficient
information about the possible failure state of the devices to make a good
determination if the array can be activated. The second check is simply
done wrong in the case of RAID10 because it doesn't account for the
independence of the stripes (i.e. mirror sets). The solution is to use the
properly written check ('validate_rebuild_devices'), but perform the check
after the superblocks have been read and we know which devices have failed.
This gives us one check instead of two and performs it in a location where
it can be done right.
Only RAID10 was affected and it was affected in the following ways:
- the code did not properly catch the condition where a user specified
a device for rebuild that already had a failed device in the same mirror
set. (This condition would, however, be caught at a deeper level in MD.)
- the code triggers a false positive and denies activation when devices in
independent mirror sets have failed - counting the failures as though they
were all in the same set.
The most likely place this error was introduced (or this patch should have
been included) is in commit 4ec1e369 - first introduced in v3.7-rc1.
Consequently this fix should also go in v3.7.y, however there is a
small conflict on the .version in raid_target, so I'll submit a
separate patch to -stable.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The relation between PIN_BANK numbers and pio letters wasn't made very
clear.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Paul Gortmaker says:
====================
The Ethernet-HowTo was maintained for roughly 10 years, from 1993 to 2003.
Fortunately sane hardware probing and auto detection (via PCI and ISA/PnP)
largely made the document a relic of the past, hence it being abandoned
a decade ago.
However, there is one last useful thing that we can extract from the
effort made in maintaining that document. We can use it to guide us
with respect to what rare, experimental and/or super ancient 10Mbit
ISA drivers don't make sense to maintain in-tree anymore.
Nobody will argue that ISA is obsolete. Availability went away at about
the time Pentium3 motherboards moved from 500MHz Slot1/SECC processors
to the green 500MHz Socket 370 Pentium3 chips, at the turn of the century.
In theory, it is possible that someone could still be running one of these
12+ year old P3 machines and want 3.9+ bleeding edge kernels (but unlikely).
In light of the above (remote) possibility, we can defer the removal of some
ISA network drivers that were highly popular and well tested. Typically
that means the stuff more from the mid to late '90s, some with ISA PnP
support, like the 3c509, the wd/SMC 8390 based stuff, PCnet/lance etc.
But a lot of other drivers, typically from the early 1990s were for rare
hardware, and experimental (to the point of requiring a cron job that would
do a test ping, and then ifconfig down/up and/or a rmmod/insmod!). And
some of these drivers (znet, and lp486e to name two) are physically tied
to platforms with on motherboard ethernet -- of 486 machines that date
from the early 1990s and can only have single digit amounts of memory.
What I'd like to achieve here with this series, is to get rid of those old
drivers that are no longer being used. In an earlier discussion where
I'd proposed deleting a single driver, Alan suggested we instead dump
all the historical stuff in one go, to make it "...immediately obvious
where the break point is..."[1] and that it was "perfectly reasonable it
(and a pile of other ISA cards) ought to be shown the door"[2]. So that
is the goal here - make a clear line in the sand where the really ancient
stuff finally gets kicked to the curb.
Two old parallel port drivers are considered for removal here as well,
since in early 386/486 ISA machines, the parallel port was typically found
with the UARTS on the multi-I/O ISA controller card. These drivers also date
from the early 1990's; parallel ports are no longer found on modern boards,
and their performance was not even capable of 10% of 10Mbit bandwidth.
Allow me a preemptive justification against the inevitable comments from
well meaning bystanders who suggest "why not just leave all this alone?".
Dead drivers cost us all if they are left in tree. If you think that
is false, then please first consider:
-every time you type "git status", you are checking to see if modifications
have been made by you to all that dead code.
-every time you type "git grep <regex>" you are searching through files
which contain that dead code that simply does not interest you.
-every time you build a "allyesconfig" and an "allmodconfig" (don't tell
me you skip this step before submitting your changes to a maintainer),
you waste CPU cycles building this dead code.
-every time there is a tree wide API change, or cleanup, or file relocation,
we pay the cost of updating dead code, or moving dead code.
-daily regression tests (take linux-next as the most transparent
example) spend time building (and possibly running) this dead code.
-hard working people who regularly run auditing tools looking for lurking
bugs (sparse/coverity/smatch/coccinelle) are wasting time checking for,
and fixing bugs in this dead code.
This last one is key. Please take a look at the git history for the
files that are proposed for removal here. Look at the git history for
any one of them ("git whatchanged --follow drivers/net/.../driver.c")
Mentally sort the changes into two bins -- (1) the robotic tree-wide
changes, and (2) the "look I found a real run-time bug while using this"
category. You will see that category #2 is essentially empty.
Further to that, realize that drivers don't simply disappear. We are
not operating in the binary-only distribution space like other OS. All
these drivers remain in the git history forever. If a person is an
enthusiast for extreme legacy hardware, they are probably already
customizing their kernel source and building it themselves to support
such systems. Also keep in mind that they could still build the 3.8
kernel exactly as-is, and run it (or a 3.8.x stable variant of it) for
several more years if they were really determined to cling to these old
experimental ISA drivers for some reason.
In summary, I hope that folks can be pragmatic about this, and not
get swept up in nostalgia. Ask yourself whether it is realistic to
expect a person would have a genuine use case where they would
need to build a 3.9+ modern kernel and install it on some legacy hardware
that has no option but to absolutely _require_ one of the drivers
that are deleted here.
The following series was created with --irreversible-delete for
ease of review (it skips showing the content of files that are
deleted); however the complete patches can be pulled as per below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have removed NCE (Neighbour Cache Entry) reference from
routing entries, the only refcnt holders of an NCE are its timer
(if running) and its owner table, in usual cases. As a result,
neigh_periodic_work() purges NCEs over and over again even for
gateways.
It does not make sense to purge entries, if number of them is
very small, so keep them. The minimum number of entries to keep
is specified by gc_thresh1.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Support swap file and link generic_file_remap_pages
o Enhance the bio streaming flow and free section control
o Major bug fix on recovery routine
o Minor bug/warning fixes and code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vJQc
-----END PGP SIGNATURE-----
Merge tag 'f2fs-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs fixes from Jaegeuk Kim:
o Support swap file and link generic_file_remap_pages
o Enhance the bio streaming flow and free section control
o Major bug fix on recovery routine
o Minor bug/warning fixes and code cleanups
* tag 'f2fs-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (22 commits)
f2fs: use _safe() version of list_for_each
f2fs: add comments of start_bidx_of_node
f2fs: avoid issuing small bios due to several dirty node pages
f2fs: support swapfile
f2fs: add remap_pages as generic_file_remap_pages
f2fs: add __init to functions in init_f2fs_fs
f2fs: fix the debugfs entry creation path
f2fs: add global mutex_lock to protect f2fs_stat_list
f2fs: remove the blk_plug usage in f2fs_write_data_pages
f2fs: avoid redundant time update for parent directory in f2fs_delete_entry
f2fs: remove redundant call to set_blocksize in f2fs_fill_super
f2fs: move f2fs_balance_fs to punch_hole
f2fs: add f2fs_balance_fs in several interfaces
f2fs: revisit the f2fs_gc flow
f2fs: check return value during recovery
f2fs: avoid null dereference in f2fs_acl_from_disk
f2fs: initialize newly allocated dnode structure
f2fs: update f2fs partition info about SIT/NAT layout
f2fs: update f2fs document to reflect SIT/NAT layout correctly
f2fs: remove unneeded INIT_LIST_HEAD at few places
...
This is another one that makes sense to target for obsolescence, since
it (a)appeared pre-1995, and (b)was rather rare, and (c)did not
really have any statistically significant active linux user base.
Removing this ISA 10Mbit driver support is unlikely to be even noticed
by the user base of 3.9+ linux kernels, especially when the documentation
clearly indicates the vintage with this text:
"...designed to work with all kernels > 1.1.33"
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These are old ISA 10Mbit cards from the 1st 1/2 of the 1990s and
required manual jumper settings in order to configure them. Here
we remove them on the premise that they are no longer used in any
modern 3.9+ kernels.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The parallel port is largely replaced by USB, and even in the
day where these drivers were current, the documented speed was
less than 100kB/s. Let us not pretend that anyone cares about
these drivers anymore, or worse - pretend that anyone is using
them on a modern kernel.
As a side bonus, this is the end of legacy parallel port ethernet,
so we get to drop the whole chunk relating to that in the legacy
Space.c file containing the non-PCI unified probe dispatch.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The original intent of this file was to list limitations in
drivers/hardware relating to multicast use, back when some
modest hardware from the early 1990s did not support things
we might take for granted today.
I was intending to delete some now-gone MCA/token ring entries
in this file, but once I opened it, I found it only contained
information on the earliest (pre-2000) linux networking drivers.
Checking the git history shows that the file hasn't been touched
since 2005. Clearly nobody is actively consulting this file
as a meaningful reference.
Rather than add a "YES YES YES" line for all of the drivers we
currently have, lets just take advantage of the fact that nobody
is using the file to delete it.
This has the side benefit of not having to do a line-by-line
deletion of the file content as each older driver is expired.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I grepped through the code and picked bits about nf_conntrack sysctl api
and put that into one documentation file.
[ I have mangled this patch including comments from several grammar
improvements proposed by Neal Murphy <neal.p.murphy@alum.wpi.edu>,
any new grammar error is my mistake --pablo ]
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
While a privileged program can open a raw socket, attach some
restrictive filter and drop its privileges (or send the socket to an
unprivileged program through some Unix socket), the filter can still
be removed or modified by the unprivileged program. This commit adds a
socket option to lock the filter (SO_LOCK_FILTER) preventing any
modification of a socket filter program.
This is similar to OpenBSD BIOCLOCK ioctl on bpf sockets, except even
root is not allowed change/drop the filter.
The state of the lock can be read with getsockopt(). No error is
triggered if the state is not changed. -EPERM is returned when a user
tries to remove the lock or to change/remove the filter while the lock
is active. The check is done directly in sk_attach_filter() and
sk_detach_filter() and does not affect only setsockopt() syscall.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output of a git grep happened to make me look into this file, and
I found instructions about how to hand patch (without using patch)
the driver into the kernel tree.
Since the driver has been a part of the mainline kernel for years,
we can dump this whole section. Fortunately it doesn't even cause
a renumbering of the sections to do so.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit (commit 7e3a2dc529 doc: make the description of how tcp_ecn
works more explicit and clear ) clarified the behavior of tcp_ecn sysctl
variable but description is inconsistent. When requested by incoming conections,
ECN is enabled with not just tcp_ecn = 2 but also with tcp_ecn = 1.
This patch makes it clear that with tcp_ecn = 1, ECN is enabled when requested
by incoming connections.
Also fix spelling of 'incoming'.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pn544 driver no longer has a /dev/pn544 interface nor a sysfs one.
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
People are back from the holiday breaks, and it shows. Here are a bunch of
fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups,
a few __init annotation fixes and some error handling improvement
in their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to see
here, mostly from the OMAP PM changes, but nothing overly crazy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9fE
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
Update the netconsole document as well.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The as-documented rcu_nocb_poll will fail to enable this feature
for two reasons. (1) there is an extra "s" in the documented
name which is not in the code, and (2) since it uses module_param,
it really is expecting a prefix, akin to "rcutree.fanout_leaf"
and the prefix isn't documented.
However, there are several reasons why we might not want to
simply fix the typo and add the prefix:
1) we'd end up with rcutree.rcu_nocb_poll, and rather probably make
a change to rcutree.nocb_poll
2) if we did #1, then the prefix wouldn't be consistent with the
rcu_nocbs=<cpumap> parameter (i.e. one with, one without prefix)
3) the use of module_param in a header file is less than desired,
since it isn't immediately obvious that it will get processed
via rcutree.c and get the prefix from that (although use of
module_param_named() could clarify that.)
4) the implied export of /sys/module/rcutree/parameters/rcu_nocb_poll
data to userspace via module_param() doesn't really buy us anything,
as it is read-only and we can tell if it is enabled already without
it, since there is a printk at early boot telling us so.
In light of all that, just change it from a module_param() to an
early_setup() call, and worry about adding it to /sys later on if
we decide to allow a dynamic setting of it.
Also change the variable to be tagged as read_mostly, since it
will only ever be fiddled with at most, once at boot.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7Dk+AAoJEFBXWFqHsHzOUugIAJZblDy7ORFZhW0R8L4Be541
pS5aBGFY7VYCrL9BGUKGsLuITI+arbYFHc+H4nqhNMBAvgChPxJZMnaG4kp1Q5Vm
AVr9tNrwsauVHLlryUk4ekut4G4WWo1NDcFq4S6rxD/jxA/uP6rnMUCY6PX4LLL9
ZpGDb3BWQ2bbUaANu3cjc1I1/Gle1ir9LObm6ZC6l8MHTTG7hyTMHvS8eCZzmDbc
9z01ZrvTKn1AneeHOpArd2/jo14b6Kap8ykx2hdVUeBhIbZp3pomezZau9ya8/kB
+1BQVODdkOMzBm6gkIkfU3HbUPnIPL18MG/uKyD+f67YkX5YODinUVdq63upLxc=
=7yrS
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
It includes one critical fix - wrong flexcan2 clock will hang system
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
* tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mx5: Fix MX53 flexcan2 clock
ARM: dts: imx31-bug: Fix manufacturer compatible string
clk: imx: Remove 'clock-output-names' from the examples
Pull networking fixes from David Miller:
1) New sysctl ndisc_notify needs some documentation, from Hanns
Frederic Sowa.
2) Netfilter REJECT target doesn't set transport header of SKB
correctly, from Mukund Jampala.
3) Forcedeth driver needs to check for DMA mapping failures, from Larry
Finger.
4) brcmsmac driver can't use usleep_range while holding locks, use
udelay instead. From Niels Ole Salscheider.
5) Fix unregister of netlink bridge multicast database handlers, from
Vlad Yasevich and Rami Rosen.
6) Fix checksum calculations in netfilter's ipv6 network prefix
translation module.
7) Fix high order page allocation failures in netfilter xt_recent, from
Eric Dumazet.
8) mac802154 needs to use netif_rx_ni() instead of netif_rx() because
mac802154_process_data() can execute in process rather than
interrupt context. From Alexander Aring.
9) Fix splice handling of MSG_SENDPAGE_NOTLAST, otherwise we elide one
tcp_push() too many. From Eric Dumazet and Willy Tarreau.
10) Fix skb->truesize tracking in XEN netfront driver, from Ian
Campbell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
xen/netfront: improve truesize tracking
ipv4: fix NULL checking in devinet_ioctl()
tcp: fix MSG_SENDPAGE_NOTLAST logic
net/ipv4/ipconfig: really display the BOOTP/DHCP server's address.
ip-sysctl: fix spelling errors
mac802154: fix NOHZ local_softirq_pending 08 warning
ipv6: document ndisc_notify in networking/ip-sysctl.txt
ath9k: Fix Kconfig for ATH9K_HTC
netfilter: xt_recent: avoid high order page allocations
netfilter: fix missing dependencies for the NOTRACK target
netfilter: ip6t_NPT: fix IPv6 NTP checksum calculation
bridge: add empty br_mdb_init() and br_mdb_uninit() definitions.
vxlan: allow live mac address change
bridge: Correctly unregister MDB rtnetlink handlers
brcmfmac: fix parsing rsn ie for ap mode.
brcmsmac: add copyright information for Canonical
rtlwifi: rtl8723ae: Fix warning for unchecked pci_map_single() call
rtlwifi: rtl8192se: Fix warning for unchecked pci_map_single() call
rtlwifi: rtl8192de: Fix warning for unchecked pci_map_single() call
rtlwifi: rtl8192ce: Fix warning for unchecked pci_map_single() call
...
* Removal of some ACPICA code that the kernel will never use from Lv Zheng.
* APEI fix from Adrian Huang.
* Removal of unnecessary ACPI memory hotplug driver code from Liu Jinsong.
* Minor ACPI power management fixes.
* ACPI debug code fix from Joe Perches.
* ACPI fix to make system bus device nodes get the right names.
* PNP resources handling fixes from Witold Szczeponik.
* cpuidle fix for a recent regression stalling boot on systems with great
numbers of CPUs from Daniel Lezcano.
* cpuidle fixes from Sivaram Nair.
* intel_idle debug message fix from Youquan Song.
* cpufreq build regression fix from Larry Finger.
* cpufreq fix for an obscure initialization race related to statistics from
Konstantin Khlebnikov.
* cpufreq change disabling the Longhaul driver by default from Rafał Bilski.
* PM core fix preventing device suspend errors from happening during system
suspend due to obscure race conditions.
* PM QoS local variable name cleanup.
--
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=k35e
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Removal of some ACPICA code that the kernel will never use from Lv
Zheng.
- APEI fix from Adrian Huang.
- Removal of unnecessary ACPI memory hotplug driver code from Liu
Jinsong.
- Minor ACPI power management fixes.
- ACPI debug code fix from Joe Perches.
- ACPI fix to make system bus device nodes get the right names.
- PNP resources handling fixes from Witold Szczeponik.
- cpuidle fix for a recent regression stalling boot on systems with
great numbers of CPUs from Daniel Lezcano.
- cpuidle fixes from Sivaram Nair.
- intel_idle debug message fix from Youquan Song.
- cpufreq build regression fix from Larry Finger.
- cpufreq fix for an obscure initialization race related to statistics
from Konstantin Khlebnikov.
- cpufreq change disabling the Longhaul driver by default from Rafał
Bilski.
- PM core fix preventing device suspend errors from happening during
system suspend due to obscure race conditions.
- PM QoS local variable name cleanup.
* tag 'pm+acpi-for-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Move disabling/enabling runtime PM to late suspend/early resume
PM / QoS: Rename local variable in dev_pm_qos_add_ancestor_request()
ACPI / scan: Do not use dummy HID for system bus ACPI nodes
cpufreq / governor: Fix problem with cpufreq_ondemand or cpufreq_conservative
cpufreq / Longhaul: Disable driver by default
cpufreq / stats: fix race between stats allocation and first usage
cpuidle: fix lock contention in the idle path
intel_idle: pr_debug information need separated
cpuidle / coupled: fix ready counter decrement
cpuidle: Fix finding state with min power_usage
PNP: Handle IORESOURCE_BITS in resource allocation
PNP: Simplify setting of resources
ACPI / power: Remove useless message from device registering routine
ACPI / glue: Update DBG macro to include KERN_DEBUG
ACPI / PM: Do not apply ACPI_SUCCESS() to acpi_bus_get_device() result
ACPI / memhotplug: remove redundant logic of acpi memory hotadd
ACPI / APEI: Fix the returned value in erst_dbg_read
ACPICA: Remove useless mini-C library.
Improve the documentation to clarify level vs edge triggered power off.
Improve the comments for level vs edge triggered power off.
Make use of gpio_is_valid().
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently, the PM core disables runtime PM for all devices right
after executing subsystem/driver .suspend() callbacks for them
and re-enables it right before executing subsystem/driver .resume()
callbacks for them. This may lead to problems when there are
two devices such that the .suspend() callback executed for one of
them depends on runtime PM working for the other. In that case,
if runtime PM has already been disabled for the second device,
the first one's .suspend() won't work correctly (and analogously
for resume).
To make those issues go away, make the PM core disable runtime PM
for devices right before executing subsystem/driver .suspend_late()
callbacks for them and enable runtime PM for them right after
executing subsystem/driver .resume_early() callbacks for them. This
way the potential conflitcs between .suspend_late()/.resume_early()
and their runtime PM counterparts are still prevented from happening,
but the subtle ordering issues related to disabling/enabling runtime
PM for devices during system suspend/resume are much easier to avoid.
Reported-and-tested-by: Jan-Matthias Braun <jan_braun@gmx.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: 3.4+ <stable@vger.kernel.org>
Add 3 new variables and sysctls to tune them (by one "next_id" variable
for messages, semaphores and shared memory respectively). This variable
can be used to set desired id for next allocated IPC object. By default
it's equal to -1 and old behaviour is preserved. If this variable is
non-negative, then desired idr will be extracted from it and used as a
start value to search for free IDR slot.
Notes:
1) this patch doesn't guarantee that the new object will have desired
id. So it's up to user space how to handle new object with wrong id.
2) After a sucessful id allocation attempt, "next_id" will be set back
to -1 (if it was non-negative).
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I slipped in a new sysctl without proper documentation. I would like to
make up for this now.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
'clock-output-names' is not used in any of the dts/dtsi files for i.mx.
Remove it from the examples, so that the example and the real usage in the
dtsi files can match.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
document to reflect the layout generated by mkfs.f2fs .
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Here are the remaining __dev* removal patches against the 3.8-rc2 tree.
All of these patches were previously sent to the subsystem maintainers,
most of them were picked up and pushed to you, but there were a number
that fell through the cracks, and new drivers were added during the
merge window, so this series cleans up the rest of the instances of
these markings.
Third time's the charm...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDmHOIACgkQMUfUDdst+ykTZgCePgK84Im3FFooEXJwaPbaf4ls
lO4AoMEDoWK+BHWOsjQwFPOwFFPEN2Xh
=6oAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core __dev* removal patches - take 3 - from Greg Kroah-Hartman:
"Here are the remaining __dev* removal patches against the 3.8-rc2
tree. All of these patches were previously sent to the subsystem
maintainers, most of them were picked up and pushed to you, but there
were a number that fell through the cracks, and new drivers were added
during the merge window, so this series cleans up the rest of the
instances of these markings.
Third time's the charm...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflict with the pinctrl pull in pinctrl-sirf.c.
* tag 'driver-core-3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
misc: remove __dev* attributes.
include: remove __dev* attributes.
Documentation: remove __dev* attributes.
Drivers: misc: remove __dev* attributes.
Drivers: block: remove __dev* attributes.
Drivers: bcma: remove __dev* attributes.
Drivers: char: remove __dev* attributes.
Drivers: clocksource: remove __dev* attributes.
Drivers: ssb: remove __dev* attributes.
Drivers: dma: remove __dev* attributes.
Drivers: gpu: remove __dev* attributes.
Drivers: infinband: remove __dev* attributes.
Drivers: memory: remove __dev* attributes.
Drivers: mmc: remove __dev* attributes.
Drivers: iommu: remove __dev* attributes.
Drivers: power: remove __dev* attributes.
Drivers: message: remove __dev* attributes.
Drivers: macintosh: remove __dev* attributes.
Drivers: mfd: remove __dev* attributes.
pstore: remove __dev* attributes.
...
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from the kernel documentation.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>