Merge reason: This branch was on an -rc5 base so pull almost-2.6.30
to resync with the latest upstream fixes and make sure
the combination works fine.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/pci: fix mmconfig detection with 32bit near 4g
PCI: use fixed-up device class when configuring device
The current code to set up the GART as an IOMMU enables GART
translations before it removes the aperture from the kernel memory
map, sets the GART PTEs to UC, sets up the guard and scratch
pages, or does a wbinvd(). This leaves the possibility of cache
aliasing open and can cause system crashes.
Re-order the code so as to enable the GART translations only
after all safeguards are in place and the tlb has been flushed.
AMD has tested this patch on both Istanbul systems and 1st
generation Opteron systems with APG enabled and seen no adverse
effects. Istanbul systems with HT Assist enabled sometimes
see MCE errors due to cache artifacts with the unmodified
code.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Cc: <stable@kernel.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: akpm@linux-foundation.org
Cc: jbarnes@virtuousgeek.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The powernow-k8 driver checks to see that the Performance Control/Status
Registers are declared as FFH (functional fixed hardware) by the BIOS.
However, this check got broken in the commit:
0e64a0c982
[CPUFREQ] checkpatch cleanups for powernow-k8
Fix based on an original patch from Naga Chumbalkar.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
We don't set up the canary; let's disable stack protector on boot.c so
we can get into lguest_init, then set it up. As a side effect,
switch_to_new_gdt() sets up %fs for us properly too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pascal reported and bisected a commit:
| x86/PCI: don't call e820_all_mapped with -1 in the mmconfig case
which broke one system system.
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255
PCI: MCFG area at f0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG for extended config space
it didn't have
PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
anymore, and try to use 0xf000000 - 0xffffffff for mmconfig
For 32bit, mcfg_res->end could be 32bit only (if 64 resources aren't used)
So use end - 1 to pass the value in mcfg->end to avoid overflow.
We don't need to worry about the e820 path, they are always 64 bit.
Reported-by: Pascal Terjan <pterjan@mandriva.com>
Bisected-by: Pascal Terjan <pterjan@mandriva.com>
Tested-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, pxa27x_udc tries to use GPIO 0 as D+ pullup if not
explicitly configured. Default to an invalid GPIO (-1) instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The UV tlb shootdown code has a serious initialization error.
An array of structures [32*8] is initialized as if it were [32].
The array is indexed by (cpu number on the blade)*8, so the short
initialization works for up to 4 cpus on a blade.
But above that, we provide an invalid opcode to the hub's
broadcast assist unit.
This patch changes the allocation of the array to use its symbolic
dimensions for better clarity. And initializes all 32*8 entries.
Shortened 'UV_ACTIVATION_DESCRIPTOR_SIZE' to 'UV_ADP_SIZE' per Ingo's
recommendation.
Tested on the UV simulator.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
LKML-Reference: <E1M6lZR-0007kV-Aq@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the __initdata annotation for the clock lookups, since they will
be needed when loading modules which use clk_get().
Tested-by: Agustín Ferrín Pozuelo <gatoguan-os@yahoo.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In alloc_coherent there is an omitted unlock on the path where mapping
fails. Add the unlock.
[ Impact: fix lock imbalance in alloc_coherent ]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
git status complains of untracked (generated) files in arch/x86/boot..
# Untracked files:
# (use "git add <file>..." to include in what will be committed)
#
# ../../arch/x86/boot/compressed/mkpiggy
# ../../arch/x86/boot/compressed/piggy.S
# ../../arch/x86/boot/compressed/vmlinux.lds
# ../../arch/x86/boot/voffset.h
# ../../arch/x86/boot/zoffset.h
..so adjust .gitignore files accordingly.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Currently, whenever an erratum workaround is enabled, it will be
applied whether or not the erratum is relevent for the CPU. This
patch changes this - we check the variant and revision fields in the
main ID register to determine which errata to apply.
We also avoid re-applying erratum 460075 if it has already been applied.
Applying this fix in non-secure mode results in the kernel failing to
boot (or even do anything.)
This fixes booting on some ARMv7 based platforms which otherwise
silently fail.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define ARCH_KMALLOC_MINALIGN in asm/cache.h
At the request of Russell also move ARCH_SLAB_MINALIGN to this file.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the fact that the IOAPIC version number in the x86_64 code path always
gets assigned to 0, instead of the correct value.
Before the patch: (from "dmesg" output):
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23 <---
After the patch:
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 <---
History:
io_apic_get_version() was compiled out of the x86_64 code path in the commit
f2c2cca3acef8b253a36381d9b469ad4fb08563a:
Author: Andi Kleen <ak@suse.de>
Date: Tue Sep 26 10:52:37 2006 +0200
[PATCH] Remove APIC version/cpu capability mpparse checking/printing
ACPI went to great trouble to get the APIC version and CPU capabilities
of different CPUs before passing them to the mpparser. But all
that data was used was to print it out. Actually it even faked some data
based on the boot cpu, not on the actual CPU being booted.
Remove all this code because it's not needed.
Cc: len.brown@intel.com
At the time, the IOAPIC version number was deliberately not printed
in the x86_64 code path. However, after the x86 and x86_64 files were
merged, the net result is that the IOAPIC version is printed incorrectly
in the x86_64 code path.
The patch below provides a fix. I have tested it with acpi, and with
acpi=off, and did not see any problems.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
LKML-Reference: <20090416014230.4885.94926.sendpatchset@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
*************************
Merge reason: irq/numa didnt build because this commit:
2759c32: x86: don't call read_apic_id if !cpu_has_apic
Had a dependency on x86/cpufeature changes. Pull in that
(small) branch to fix the dependency.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
arch/mips/sibyte/bcm1480/irq.c
arch/mips/sibyte/sb1250/irq.c
Merge reason: we gathered a few conflicts plus update to latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] update mach-types
[ARM] Add cmpxchg support for ARMv6+ systems (v5)
[ARM] barriers: improve xchg, bitops and atomic SMP barriers
Gemini: Fix SRAM/ROM location after memory swap
MAINTAINER: Add F: entries for Gemini and FA526
[ARM] disable NX support for OABI-supporting kernels
[ARM] add coherent DMA mask for mv643xx_eth
[ARM] pxa/palm: fix PalmLD/T5/TX AC97 MFP
[ARM] pxa: add parameter to clksrc_read() for pxa168/910
[ARM] pxa: fix the incorrectly defined drive strength macros for pxa{168,910}
[ARM] Orion: Remove explicit name for platform device resources
[ARM] Kirkwood: Correct MPP for SATA activity/presence LEDs of QNAP TS-119/TS-219.
[ARM] pxa/ezx: fix pin configuration for low power mode
[ARM] pxa/spitz: provide spitz_ohci_exit() that unregisters USB_HOST GPIO
[ARM] pxa: enable GPIO receivers after configuring pins
[ARM] pxa: allow gpio_reset drive high during normal work
[ARM] pxa: save/restore PGSR on suspend/resume.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13302
On x86 and x86-64, it is possible that page tables are shared beween
shared mappings backed by hugetlbfs. As part of this,
page_table_shareable() checks a pair of vma->vm_flags and they must match
if they are to be shared. All VMA flags are taken into account, including
VM_LOCKED.
The problem is that VM_LOCKED is cleared on fork(). When a process with a
shared memory segment forks() to exec() a helper, there will be shared
VMAs with different flags. The impact is that the shared segment is
sometimes considered shareable and other times not, depending on what
process is checking.
What happens is that the segment page tables are being shared but the
count is inaccurate depending on the ordering of events. As the page
tables are freed with put_page(), bad pmd's are found when some of the
children exit. The hugepage counters also get corrupted and the Total and
Free count will no longer match even when all the hugepage-backed regions
are freed. This requires a reboot of the machine to "fix".
This patch addresses the problem by comparing all flags except VM_LOCKED
when deciding if pagetables should be shared or not for hugetlbfs-backed
mapping.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <starlight@binnacle.cx>
Cc: Eric B Munson <ebmunson@us.ibm.com>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The flat loader uses an architecture's flat_stack_align() to align the
stack but assumes word-alignment is enough for the data sections.
However, on the Xtensa S6000 we have registers up to 128bit width
which can be used from userspace and therefor need userspace stack and
data-section alignment of at least this size.
This patch drops flat_stack_align() and uses the same alignment that
is required for slab caches, ARCH_SLAB_MINALIGN, or wordsize if it's
not defined by the architecture.
It also fixes m32r which was obviously kaput, aligning an
uninitialized stack entry instead of the stack pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Oskar Schirmer <os@emlix.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add cmpxchg/cmpxchg64 support for ARMv6K and ARMv7 systems
(original patch from Catalin Marinas <catalin.marinas@arm.com>)
The cmpxchg and cmpxchg64 functions can be implemented using the
LDREX*/STREX* instructions. Since operand lengths other than 32bit are
required, the full implementations are only available if the ARMv6K
extensions are present (for the LDREXB, LDREXH and LDREXD instructions).
For ARMv6, only 32-bits cmpxchg is available.
Mathieu :
Make cmpxchg_local always available with best implementation for all type sizes (1, 2, 4 bytes).
Make cmpxchg64_local always available.
Use "Ir" constraint for "old" operand, like atomic.h atomic_cmpxchg does.
Change since v3 :
- Add "memory" clobbers (thanks to Nicolas Pitre)
- removed __asmeq(), only needed for old compilers, very unlikely on ARMv6+.
Note : ARMv7-M should eventually be ifdefed-out of cmpxchg64. But it's not
supported by the Linux kernel currently.
Put back arm < v6 cmpxchg support.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mathieu Desnoyers pointed out that the ARM barriers were lacking:
- cmpxchg, xchg and atomic add return need memory barriers on
architectures which can reorder the relative order in which memory
read/writes can be seen between CPUs, which seems to include recent
ARM architectures. Those barriers are currently missing on ARM.
- test_and_xxx_bit were missing SMP barriers.
So put these barriers in. Provide separate atomic_add/atomic_sub
operations which do not require barriers.
Reported-Reviewed-and-Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This will test the automatic aperture enlargement code. This is
important because only very few devices will ever trigger this code
path. So force it under CONFIG_IOMMU_STRESS.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Disabling the round-robin allocator results in reusing the same
dma-addresses again very fast. This is a good test if the iotlb flushing
is working correctly.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch makes sure no reserved addresses are allocated in an dma_ops
domain when the aperture is increased dynamically.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Simplify the code a little bit by using the same unit for all address
space related state in the dma_ops domain structure.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch changes the AMD IOMMU address allocator to allow up to 32
aperture ranges per dma_ops domain.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The code will be required when the aperture size increases dynamically
in the extended address allocator.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch makes sure that no function required for suspend/resume of
AMD IOMMU driver is thrown away after boot.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Current hardware uses msi instead of msi-x so this code it not necessary
and can not be tested. The best thing is to drop this code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch restructures the AMD IOMMU initialization code to initialize
all hardware registers with one single function call.
This is helpful for suspend/resume support.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch introduces the for_each_iommu and for_each_iommu_safe macros
to simplify the developers life when having to iterate over all AMD
IOMMUs in the system.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Some drivers may use the dma api during ->remove which will
cause a protection domain to get reattached to a device. Delay the
detach until after the driver is completely unbound.
[ joro: added a little merge helper ]
[ Impact: fix too early device<->domain removal ]
Signed-off-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The bug never triggered. But it should be fixed to protect against
broken ACPI tables in the future.
[ Impact: protect against broken ivrs acpi table ]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The devid parameter to set_dev_entry_from_acpi is the requester ID
rather than the device ID since it is used to index the IOMMU device
table. The handling of IVHD_DEV_ALIAS used to pass the device ID.
This patch fixes it to pass the requester ID.
[ Impact: fix setting the wrong req-id in acpi-table parsing ]
Signed-off-by: Neil Turton <nturton@solarflare.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The variable amd_iommu_last_bdf holds the maximum bdf of any device
controlled by an IOMMU, so the number of device entries needed is
amd_iommu_last_bdf+1. The function tbl_size used amd_iommu_last_bdf
instead. This would be a problem if the last device were a large
enough power of 2.
[ Impact: fix amd_iommu_last_bdf off-by-one error ]
Signed-off-by: Neil Turton <nturton@solarflare.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This Kconfig option is intended to enable various code paths or
parameters in IOMMU implementations to stress test the code and/or the
hardware. This can also be done by disabling optimizations in the code
when this option is switched on.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Add information about device memory mapping requirements for the IOMMU
as described in the IVRS ACPI table to the kernel log if amd_iommu_dump
was specified on the kernel command line.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add information about devices belonging to an IOMMU as described in the
IVRS ACPI table to the kernel log if amd_iommu_dump was specified on the
kernel command line.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add information about IOMMU devices described in the IVRS ACPI table to
the kernel log if amd_iommu_dump was specified on the kernel command
line.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This kernel parameter will be useful to get some AMD IOMMU related
information in dmesg that is not necessary for the default user but may
be helpful in debug situations.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The *fence instructions were moved to vsyscall_64.c by commit
cb9e35dce9. But this breaks the
vDSO, because vread methods are also called from there.
Besides, the synchronization might be unnecessary for other
time sources than TSC.
[ Impact: fix potential time warp in VDSO ]
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
LKML-Reference: <9d0ea9ea0f866bdc1f4d76831221ae117f11ea67.1243241859.git.ptesarik@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
instead of declaring one variant as an inline function...
because other case is a variable
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4A13B344.7030307@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The implementation we just revived has issues, such as using a
Kconfig-defined virtual address area in kernel space that nothing
actually carves out (and thus will overlap whatever is there),
or having some dependencies on being self contained in a single
PTE page which adds unnecessary constraints on the kernel virtual
address space.
This fixes it by using more classic PTE accessors and automatically
locating the area for consistent memory, carving an appropriate hole
in the kernel virtual address space, leaving only the size of that
area as a Kconfig option. It also brings some dma-mask related fixes
from the ARM implementation which was almost identical initially but
grew its own fixes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make FIXADDR_TOP a compile time constant and cleanup a
couple of definitions relative to the layout of the kernel
address space on ppc32. We also print out that layout at
boot time for debugging purposes.
This is a pre-requisite for properly fixing non-coherent
DMA allocactions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some more fallout of the string changes:
CC arch/blackfin/lib/strncmp.o
In file included from include/linux/bitmap.h:9,
from include/linux/nodemask.h:90,
from include/linux/mmzone.h:17,
from include/linux/gfp.h:5,
from include/linux/kmod.h:23,
from include/linux/module.h:14,
from arch/blackfin/lib/strncmp.c:14:
include/linux/string.h: In function ‘strstarts’:
include/linux/string.h:132: error: implicit declaration of function ‘strncmp’
make[1]: *** [arch/blackfin/lib/strncmp.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Rusty Russell <rusty@rustcorp.com.au>
This reverts commit 33f00dcedb.
While it was a good idea to try to use the mm/vmalloc.c allocator instead
of our own (in fact, ours is itself a dup on an old variant of the vmalloc
one), unfortunately, the approach is terminally busted since
dma_alloc_coherent() can be called at interrupt time or in atomic contexts
and there's little chances we'll make the code in mm/vmalloc.c cope with\ that :-(
Until we can get the generic code to forbid that idiocy and fix all
drivers abusing it, we pretty much have no choice but revert to
our custom virtual space allocator.
There's also a problem with SMP safety since freeing such mapping
would require an IPI which cannot be done at interrupt time.
However, right now, I don't think we support any platform that is
both SMP and has non-coherent DMA (don't laugh, I know such things
do exist !) so we can sort that out later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: avoid back to back on_each_cpu in cpa_flush_array
x86, relocs: ignore R_386_NONE in kernel relocation entries
Cleanup cpa_flush_array() to avoid back to back on_each_cpu() calls.
[ Impact: optimizes fix 0af48f42df ]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: determine exact CPU frequency for HW Pstates
[CPUFREQ] powernow-k8 cleanup msg if BIOS does not export ACPI _PSS cpufreq data
[CPUFREQ] fix timer teardown in ondemand governor
[CPUFREQ] fix timer teardown in conservative governor
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call
[CPUFREQ] powernow-k7 build fix when ACPI=n
[CPUFREQ] add atom family to p4-clockmod
Slightly modified by trenn@suse.de -> only do this on fam 10h and fam 11h.
Currently powernow-k8 determines CPU frequency from ACPI PSS objects, but
according to AMD family 11h BKDG this frequency is just a rounded value:
"CoreFreq (MHz) = The CPU COF specified by MSRC001_00[6B:64][CpuFid]
rounded to the nearest 100 Mhz."
As a consequnce powernow-k8 reports wrong CPU frequency on some systems,
e.g. on Turion X2 Ultra:
powernow-k8: Found 1 AMD Turion(tm)X2 Ultra DualCore Mobile ZM-82
processors (2 cpu cores) (version 2.20.00)
powernow-k8: 0 : pstate 0 (2200 MHz)
powernow-k8: 1 : pstate 1 (1100 MHz)
powernow-k8: 2 : pstate 2 (600 MHz)
But this is wrong as frequency for Pstate2 is 550 MHz. x86info reports it
correctly:
#x86info -a |grep Pstate
...
Pstate-0: fid=e, did=0, vid=24 (2200MHz)
Pstate-1: fid=e, did=1, vid=30 (1100MHz)
Pstate-2: fid=e, did=2, vid=3c (550MHz) (current)
Solution is to determine the frequency directly from Pstate MSRs instead
of using rounded values from ACPI table.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
- Make the message shorter and easier to grep for
- Use printk_once instead of WARN_ONCE (functionality of these was mixed)
Signed-off-by: Thomas Renninger <trenn@suse.de>
Cc: Langsdorf, Mark <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
arch/x86/kernel/cpu/cpufreq/powernow-k7.c:172: warning: 'invalidate_entry' defined but not used
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Some atom procs don't do freq scaling (such as the atom 330 on my own
littlefalls2 board). By adding the atom family here, we at least get
the benefit of passive cooling in a thermal emergency. Not sure how
to see that its actually helping any, but the driver does bind and
claim its functioning on my atom 330.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
For relocatable 32bit kernels, boot/compressed/relocs.c processes
relocation entries in the kernel image and appends it to the kernel
image such that boot/compressed/head_32.S can relocate the kernel.
The kernel image is one statically linked object and only uses two
relocation types - R_386_PC32 and R_386_32, of the two only the latter
needs massaging during kernel relocation and thus handled by relocs.
R_386_PC32 is ignored and all other relocation types are considered
error.
When the target of a relocation resides in a discarded section,
binutils doesn't throw away the relocation record but nullifies it by
changing it to R_386_NONE, which unfortunately makes relocs fail.
The problem was triggered by yet out-of-tree x86 stack unwind patches
but given the binutils behavior, ignoring R_386_NONE is the right
thing to do.
The problem has been tracked down to binutils behavior by Jan Beulich.
[ Impact: fix build with certain binutils by ignoring R_386_NONE ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <4A1B8150.40702@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The recent rework of the MMU PID handling for non-hash CPUs has a
subtle bug in the !SMP "optimized" variant of the PID stealing
function. It clears the PID in the mm context before it calls
local_flush_tlb_mm(). However, the later will not flush anything
if the PID in the context is clear...
Signed-off-by: Hideo Saito <hsaito.ppc@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'kvm-updates/2.6.30' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Fix PDPTR reloading on CR4 writes
KVM: Make paravirt tlb flush also reload the PAE PDPTRs
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Remove remap percpu allocator for the time being
x86: cpa_flush_array wbinvd should be done on all CPUs
x86: bugfix wbinvd() model check instead of family check
x86: introduce noxsave boot parameter
x86, setup: revert ACPI 3 E820 extended attributes support
x86: DMI match for the Sony VGN-Z540N as it needs BIOS reboot
The processor is documented to reload the PDPTRs while in PAE mode if any
of the CR4 bits PSE, PGE, or PAE change. Linux relies on this
behaviour when zapping the low mappings of PAE kernels during boot.
The code already handled changes to CR4.PAE; augment it to also notice changes
to PSE and PGE.
This triggered while booting an F11 PAE kernel; the futex initialization code
runs before any CR3 reloads and writes to a NULL pointer; the futex subsystem
ended up uninitialized, killing PI futexes and pulseaudio which uses them.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
The paravirt tlb flush may be used not only to flush TLBs, but also
to reload the four page-directory-pointer-table entries, as it is used
as a replacement for reloading CR3. Change the code to do the entire
CR3 reloading dance instead of simply flushing the TLB.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Remap percpu allocator has subtle bug when combined with page
attribute changing. Remap percpu allocator aliases PMD pages for the
first chunk and as pageattr doesn't know about the alias it ends up
updating page attributes of the original mapping thus leaving the
alises in inconsistent state which might lead to subtle data
corruption. Please read the following threads for more information:
http://thread.gmane.org/gmane.linux.kernel/835783
The following is the proposed fix which teaches pageattr about percpu
aliases.
http://thread.gmane.org/gmane.linux.kernel/837157
However, the above changes are deemed too pervasive for upstream
inclusion for 2.6.30 release, so this patch essentially disables
the remap allocator for the time being.
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <4A1A0A27.4050301@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Our signal syscall restart handling for these kernels still uses
the userspace stack to build code for restarting the syscall.
Unfortunately, fixing this is non-trivial, and so for the time
being, we resolve the problem by disabling NX support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit eb0519b5a1, mv643xx_eth is non functional on ARM because
the platform device declaration does not include any coherent DMA mask
and coherent memory allocations fail.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
cpa_flush_array seems to prefer wbinvd() over clflush at 4M threshold.
clflush needs to be done on only one CPU as per instruction definition.
wbinvd() however, should be done on all CPUs.
[ Impact: fix missing flush which could cause data corruption ]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
wbinvd is supported on all CPUs 486 or later. But,
pageattr.c is checking x86_model >= 4 before wbinvd(), which looks like
an oversight bug. It was first introduced at one place by changeset
d7c8f21a8c and got copied over to second
place in the same file later.
[ Impact: fix missing cache flush on early-model CPUs, potential data corruption ]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Ingo Molnar