When overriding the CIS, re-start the configuration of the card from
scratch. Reported and debugged by Fabrice Bellet <fabrice@bellet.info>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The return value of class_create() need to be checked with IS_ERR().
And register_chrdev() returns errno on failure.
This patch includes these fixes for cm4000_cs and cm4040_cs.
Signed-off-by: Akinbou Mita <akinobu.mita@gmail.com>
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (82 commits)
[PATCH] pata_ali: small fixes
[PATCH] pata_via: VIA 8251 bridged systems are now out and about
[PATCH] trivial piix: swap bogus dot for comma space
[PATCH] sata_promise: PHYMODE4 fixup
[PATCH] libata: always use polling IDENTIFY
[libata] pata_cs5535: fix build
[PATCH] ahci: do not powerdown during initialization
[PATCH] libata: prepare ata_sg_clean() for invocation from EH
[PATCH] libata: separate out rw ATA taskfile building into ata_build_rw_tf()
[PATCH] libata: implement ata_exec_internal_sg()
[PATCH] libata: make sure IRQ is cleared after ata_bmdma_freeze()
[PATCH] libata: move BMDMA host status recording from EH to interrupt handler
[PATCH] libata: make sure sdev doesn't go away while rescanning
[PATCH] libata: don't request sense if the port is frozen
[PATCH] libata: fix READ CAPACITY simulation
[PATCH] libata: implement ATA_FLAG_SETXFER_POLLING and use it in pata_via, take #2
[PATCH] libata: set IRQF_SHARED for legacy PCI IDE IRQs
[PATCH] libata: remove unused HSM_ST_UNKNOWN
[PATCH] libata: kill unnecessary sht->max_sectors initializations
[PATCH] libata: add missing sht->slave_destroy
...
Switch to pci_get_bus_and_slot because some x86 systems seem to be
handing us a device with dev->bus = NULL. Also don't apply the isa fixup
to revision C6 and later of the chip.
Really we need to work out wtf is handing us pdev->bus = NULL, but firstly
and more importantly we need the drivers working.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[SUNHME]: Fix for sunhme failures on x86
[XFRM] xfrm_user: Better validation of user templates.
[DCCP] tfrc: Binary search for reverse TFRC lookup
[DCCP] ccid3: Deprecate TFRC_SMALLEST_P
[DCCP] tfrc: Identify TFRC table limits and simplify code
[DCCP] tfrc: Add protection against invalid parameters to TFRC routines
[DCCP] tfrc: Fix small error in reverse lookup of p for given f(p)
[DCCP] tfrc: Document boundaries and limits of the TFRC lookup table
[DCCP] ccid3: Fix warning message about illegal ACK
[DCCP] ccid3: Fix bug in calculation of send rate
[DCCP]: Fix BUG in retransmission delay calculation
[DCCP]: Use higher RTO default for CCID3
In io_subchannel_register(), it is better to just reprobe the current
device if it hasn't a driver yet than to rescan the whole bus.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If I/O was running on a just varied off chpid, it will be terminated.
If this was a common I/O layer internal I/O, it needs to be retried.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the last path to a device is gone after a chpid has been varied
off, putting it on the slow queue doesn't prevent a device driver
from still attempting to use it (it may stay on the slow queue for a
long time). Instead, trigger a verify event which will prevent I/O
attempts from the device driver immediately.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add some prefixes to constands defined in drivers/s390/net/qdio.h
and drivers/s390/lcs.h to make it possible to include the three
header files drivers/s390/net/qeth.h, drivers/s390/net/qdio.h and
drivers/net/s390/lcs.h in one C file. This is required for the
patch that generates the kerntypes.o file for use by lcrash.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of re-IPL and diag308 doesn't work we have to reset all devices
manually and wait synchronously that each reset finished.
This patch adds the necessary infrastucture and the first exploiter of it.
Subsystems that need to add a function that needs to be called at re-IPL
may register/unregister this function via
struct reset_call {
struct reset_call *next;
void (*fn)(void);
};
void register_reset_call(struct reset_call *reset);
void unregister_reset_call(struct reset_call *reset);
When the registered function get called the context is:
- all cpus beside the current one are stopped
- all machine checks and interrupts are disabled
- prefixing is disabled
- a default machine check handler is available for use
The registered functions may not take any locks are sleep.
For the common I/O layer part of this patch:
Introduce a reset_call css_reset that does the following:
- clear all subchannels
- perform a rchp on all channel paths and wait for the resulting
machine checks
This replaces the calls to clear_all_subchannels() and
cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now
uses reipl_find_schid() to determine the subchannel id for a given
device id.
Also remove cio_reset_channel_paths() and friends since they are not
needed anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the return value of 'dasd_eer_enable' is returned - even if the
function returned '0'. Now return 'count' for successful execution.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case a request timed out and termination did not work, the console was
flooded with retry messages (every 1/10s). Now we use a 5s delay per retry and
generate a more precise message.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove lock pointer from 3215 device structure. Use get_ccwdev_lock
for each use of the lock in the ccw-device structure.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When writing to dasd attributes (e.g. readonly), all values besides '1'
are handled like '0'.
Other sysfs-attributes like 'online' are checking for '1' and for '0'
and do not accept other values. Therefore enhanced checking and error
handling in dasd_devmap attribute store functions.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The following patch fixes the failure of sunhme drivers on x86 hosts
due to missing pci_enable_device() and pci_set_master() calls, lost
during code refactoring. It has been filed as bugzilla bug #7502 [0]
and Debian bug #397460 [1].
[0] http://bugzilla.kernel.org/show_bug.cgi?id=7502
[1] http://bugs.debian.org/397460
Signed-off-by: Jurij Smakov <jurij@wooyd.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's bitrotten, long unmaintained, long hidden under BROKEN_ON_SMP,
etc. As scheduled in feature-removal-schedule.txt, and ack'd several
times on lkml.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds code to fix up the PHYMODE4 "align timing"
register value on second-generation Promise SATA chips.
Failure to correct this value on non-x86 machines makes
drive detection prone to failure due to timeouts. (I've
observed about 50% detection failure rates on SPARC64.)
The HW boots with a bad value in this register, but on x86
machines the Promise BIOS corrects it to the value recommended
by the manual, so most people have been unaffected by this issue.
After developing the patch I checked Promise's SATAII driver,
and discovered that it also corrects PHYMODE4 just like this
patch does.
This patch depends on the sata_promise SATAII updates
patch I sent recently.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata switched to IRQ-driven IDENTIFY when IRQ-driven PIO was
introduced. This has caused a lot of problems including device
misdetection and phantom device.
ATA_FLAG_DETECT_POLLING was added recently to selectively use polling
IDENTIFY on problemetic drivers but many controllers and devices are
affected by this problem and trying to adding ATA_FLAG_DETECT_POLLING
for each such case is diffcult and not very rewarding.
This patch makes libata always use polling IDENTIFY. This is
consistent with libata's original behavior and drivers/ide's behavior.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci_init_controller() calls ahci_deinit_port() to make sure the
controller is stopped before initializing the controller. In turn,
ahci_deinit_port() invokes ahci_power_down() to power down the port.
If the controller supports slumber mode, the link is put into it.
Unfortunately, some devices don't implement link powersaving mode
properly and show erratic behavior after link is put into slumber
mode. For example, HL-DT-ST DVD-RAM GSA-H30N completely locks up on
slumber transition and can only be recovered with the *REAL* hard
reset - power removal and reapply.
Note that this makes the first probing reset different from all
others. If the above dvd-ram is hotplugged after ahci is initialized,
no problem occurs because ahci is already fully initialized with phy
powered up. So, this might also be the reason for other weird AHCI
initial probing abnormalities.
This patch moves power up/down out of port init/deinit and call them
only when needed.
Power down is now called only when suspending. As system suspend
usually involves powering down 12v for storage devices, this shouldn't
cause problem even if the attached device doesn't support slumber
mode. However, in partial power management and suspend failure cases,
devices might lock up after suspend attempt. I thought about removing
transition to slumber mode altogether but ahci spec mandates it before
HBA D3 state transition. Blacklisting such devices might be the
solution.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out rw ATA taskfile building from ata_scsi_rw_xlat() into
ata_build_rw_tf(). This will be used to improve media error handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Sg'ify ata_exec_internal() and call it ata_exec_internal_sg().
Wrapper function around ata_exec_internal_sg() is implemented to
provide ata_exec_internal() interface.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that BMDMA status is recorded in irq handler. ata_bmdma_freeze()
is free to manipulate host status. Under certain circumstances, some
controllers (ICH7 in enhanced mode w/ IRQ shared) raise IRQ when CTL
register is written to and ATA_NIEN doesn't mask it.
This patch makes ata_bmdma_freeze() clear all pending IRQs after
freezing a port. This change makes explicit clearing in
ata_device_add() unnecessary and thus kills it. The removed code was
SFF-specific and was in the wrong place.
Note that ->freeze() handler is always called under ap->lock held and
irq disabled. Even if CTL manipulation causes stuck IRQ, it's cleared
immediately. This should be safe (enough) even in SMP environment.
More correct solution is to mask the IRQ from IRQ controller but that
would be an overkill.
Signed-off-by: Tejun Heo <htejun@gmail.com>
For certain errors, interrupt handler alter BMDMA host status before
entering EH (clears active and intr). Thus altered BMDMA host status
value is recorded by BMDMA EH and reported to user. Move BMDMA host
status recording from EH to interrupt handler.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_scsi_dev_rescan() doesn't synchronize against SCSI device detach
and the target sdev might go away in the middle. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
If EH command is issued to a frozen port, it fails with AC_ERR_SYSTEM.
libata used to request sense even when the port is frozen needlessly
adding AC_ERR_SYSTEM to err_mask. Don't do it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
* READ CAPACITY (16) implementation fixed. Result was shifted by two
bytes. Carlos Pardo spotted this problem and submitted preliminary
patch. Capacity => 2TB is handled correctly now. (verifid w/ fake
capacity)
* Use dev->n_sectors instead of re-reading directly from ID data.
* Define and use ATA_SCSI_RBUF_SET() which considers rbuf length.
This should be done for all simulation functions. Userland can
issue any simulated command with arbitrary buffer length.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
This patch implements ATA_FLAG_SETXFER_POLLING and use in pata_via.
If this flag is set, transfer mode setting performed by polling not by
interrupt. This should help those controllers which raise interrupt
before the command is actually complete on SETXFER.
Rationale for this approach.
* uses existing facility and relatively simple
* no busy sleep in the interrupt handler
* updating drivers is easy
While at it, kill now unused flag ATA_FLAG_SRST in pata_via.
Signed-off-by: Tejun Heo <htejun@gmail.com>
There are machines out there which share legacy PCI IDE IRQs w/ other
devices. libata SFF interrupt/HSM code is ready for shared IRQ and
has been setting IRQF_SHARED for devices in native PCI mode. Device
in legacy mode is still a PCI device and thus supposedly uses
active-low level triggered IRQ.
Machines with such setup should be quite rare and w/o this flag libata
is likely to fail loading and render the system unuseable. Also, IDE
driver has been setting IRQF_SHARED for devices in legacy mode for a
looooong time.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sht->max_sectors is overrided unconditionally in ->slave_configure.
There's no reason to set it to any value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
... into anonymous union of __wsum and __u32 (csum and csum_offset resp.)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI ID and detection for 5709 copper and SerDes chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dominik Brodowski