The DPI and HDMI interfaces use their 'set_timing' functions to take in a new
set of timings. If the panel is disabled, they do not disable and re-enable
the interface. Currently, the manager timings are applied in hdmi_power_on()
and dpi_set_mode() respectively, these are not called by set_timings if the
panel is disabled.
When checking overlay and manager data, the DSS driver uses the last applied
manager timings, and not the timings held by omap_dss_device struct. Hence,
there is a need to apply the new manager timings even if the panel is disabled.
Apply the manager timings if the panel is disabled. Eventually, there should be
one common place where the timings are applied independent of the state of the
panel.
Signed-off-by: Archit Taneja <archit@ti.com>
In order to check the validity of overlay and manager info, there was a need to
use the omap_dss_device struct to get the panel resolution. The manager's
private data in APPLY now contains the manager timings. Hence, we don't need to
rely on the display resolution any more.
Pass the manager's timings in private data to dss_mgr_check(). Remove the need
to pass omap_dss_device structs in the functions which check for the validity
of overlay and manager parameters.
Signed-off-by: Archit Taneja <archit@ti.com>
If a manager is disabled, there is no guarantee at any point in time that all
it's parameters are configured. There is always a chance that some more
parameters are yet to be configured by a user of DSS, or by DSS itself.
However, when the manager is enabled, we can be certain that all the parameters
have been configured, as we can't enable a manager with an incomplete
configuration. Therefore, if a manager is disabled, don't check for the validity
of it's parameters or the parameters of the overlays connected to it. Only check
once it is enabled. Add a check in dss_check_settings_low() to achieve the same.
Signed-off-by: Archit Taneja <archit@ti.com>
Create a function dss_mgr_check_timings() which wraps around the function
dispc_mgr_timings_ok(). This is mainly a clean up to hide dispc functions
from interface drivers.
dss_mgr_check_timings() is added in the function dss_mgr_check(), it currently
takes the timings maintained in the omap_dss_device struct. This would be later
replaced by the timings stored in the manager's private data.
Make dss_mgr_check_timings() and dispc_mgr_timings_ok() take a const
omap_video_timings pointer since these functions just check the timings.
Signed-off-by: Archit Taneja <archit@ti.com>
Replace the function dispc_mgr_set_timings() with dss_mgr_set_timings() in the
interface drivers. The latter function ensures that the timing related DISPC
registers are configured according to the shadow register programming model.
Remove the call to dispc_mgr_go() in dpi_set_timings() as the manager's go bit
is set by dss_mgr_set_timings().
Signed-off-by: Archit Taneja <archit@ti.com>
DISPC manager size and DISPC manager blanking parameters(for LCD managers)
follow the shadow register programming model. Currently, they are programmed
directly by the interface drivers.
To configure manager timings using APPLY, there is a need to introduce extra
info flags for managers, similar to what is done for overlays. This is needed
because timings aren't a part of overlay_manager_info struct configured by a
user of DSS, they are configured internally by the interface or panel drivers.
Add dirty and shadow_dirty extra_info flags for managers, update these flags
at the appropriate places. Rewrite the function extra_info_update_ongoing()
slightly as checking for manager's extra_info flags can simplify the code a bit.
Create function dss_mgr_set_timings() which applies the new manager timings to
extra_info.
Signed-off-by: Archit Taneja <archit@ti.com>
Fake VSYNC support is a hack and has some bugs in it. It isn't used by any user
of DSS. Remove Fake VSYNC support. For DSI command mode and RFBI panels, a user
of DSS should wait for the completion of a frame by using the panel driver's
sync op.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The wrong bit field was being updated in DSS_CTRL when trying to configure the
clock source of DSI2 functional clock. Use the correct bit field based on the
dsi module number.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI core register offset macros aren't defined in ascending order of their
values, some of the offset macros are also redefined. The same issues occur when
these core registers are dumped.
Clean up the ordering of HDMI core registers and remove repeated registers in
the definition in ti_hdmi_4xxx_ip.h and in ti_hdmi_4xxx_core_dump().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function ti_hdmi_4xxx_core_dump has some bugs, the following mention the
bugs and the solutions:
- The macros DUMPCORE and DUMPCOREAV in ti_hdmi_4xxx_core_dump() use
hdmi_pll_base() for the offsets needed to calculate register addresses, use
functions hdmi_core_sys_base() amd hdmi_av_base() to calculate the correct
offsets for CORE_SYS and CORE_AV registers.
- Many of the CORE_AV registers use the DUMPCORE macro, and hence the register
addresses are calculated incorrectly. Rename the current DUMPCOREAV macro as
DUMPCOREAV2 as it takes 2 arguments to dump indexed CORE_AV registers, create
a new macro called DUMPCOREAV which is now used for dumping non-indexed
CORE_AV registers.
Thanks to Ancy Tom <ancytom@gmail.com> for pointing out the issues.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.
This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.
The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:
{
0, // pin num for clock lane +
1, // pin num for clock lane -
2, // pin num for data1 lane +
3, // pin num for data1 lane -
...
}
The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The reset GPIO for Taal panel driver is currently requested in the
4430sdp board file. This patch moves the gpio request/free into the Taal
driver, where it should be.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 chip should handle the power-down signal of
the chip, instead of the current way of handling it in the board files.
This patch adds power_down_gpio into the device's platform data, and
adds the necessary code in the driver to request and handle the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC_FCLK is incorrectly used as functional clock of DISPC in scaling
calculations. So, DISPC_CORE_CLK replaces as functional clock of DISPC.
DISPC_CORE_CLK is derived from DISPC_FCLK divided by an independent DISPC
divisor LCD.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP3 DISPC video overlays suffer from some undocumented horizontal position
and timing related limitations leading to SYNCLOST errors. Whenever the image
window is moved towards the right of the screen SYNCLOST errors become
frequent. Checks have been implemented to see that DISPC driver rejects
configuration exceeding above limitations.
This code was successfully tested on OMAP3. This code is written based on code
written by Ville Syrjälä <ville.syrjala@nokia.com> in Linux OMAP kernel. Ville
Syrjälä <ville.syrjala@nokia.com> had added checks for video overlay horizontal
timing and DISPC horizontal blanking length limitations.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP3 and OMAP4, the DISPC Scaler can downscale an image up to 4 times, and
up to 2 times in OMAP2. However, with predecimation, the image can be reduced
to 16 times by fetching only the necessary pixels in memory. Then this
predecimated image can be downscaled further by the DISPC scaler.
The pipeline is configured to use a burst of size 8 * 128 bits which consists
of 8 mini bursts of 16 bytes each. So, horizontal predecimation more than 16
can lead to complete discarding of such mini bursts. L3 interconnect may
handover the bus to some other initiator and inturn delay the fetching of
pixels leading to underflows. So, maximum predecimation limit is fixed at 16.
Based on the downscaling required, a prior calculation of predecimation values
for width and height of an image is done. Since, Predecimation reduces quality
of an image higher priorty is given to DISPC Scaler for downscaling.
This code was successfully tested on OMAP2, OMAP3 and OMAP4. Horizontal and
vertical predecimation worked fine except for some synclost errors due to
undocumented errata in OMAP3 which are fixed later and skewed images were seen
on OMAP2 and OMAP3 during horizontal predecimation which will be addressed in
the future patches.
This code is based on code written by Lajos Molnar <lajos@ti.com> who had added
predecimation support for NV12/YUV/rotated/SDMA buffers.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add displays to panel-generic-dpi.c
Prime View PD050VL1 (640 x 480)
Prime View PD104SLF (800 x 600)
Prime View PM070WL4 (800 x 480)
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up the DISPC manager timings related function by:
- Create a common function to set size for LCD and TV.
- Create a common function to check timings for LCD and TV.
- Add dss params to get the range of manager size.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, a LCD manager's timings is set by dispc_mgr_set_lcd_timings() and TV
manager's timings is set by dispc_set_digit_size(). Use a common function called
dispc_mgr_set_timings() which sets timings for both type of managers.
We finally want the interface drivers to use an overlay manager function to
configure it's timings, having a common DISPC function would make things
cleaner.
For LCD managers, dispc_mgr_set_timings() sets LCD size and blanking values, for
TV manager, it sets only the TV size since blanking values don't exist for TV.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The RFBI driver uses dispc_mgr_set_lcd_size() to set the width and height of
the LCD manager. Replace this to use dispc_mgr_set_lcd_timings(), pass dummy
blanking parameters like done in the DSI driver.
This prevents the need to export dispc_mgr_set_lcd_size(), and use a common
function to set lcd timings.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The EDT ET0500G0DH6 is a 5 inch display. It is
tested on an OMAP3 board.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for the Mitsubishi display
AA084SB01. This is a 7 inch LVDS display. It is tested with
an OMAP3 board.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On pandora we use .set_timings to alter refresh rate,
so add .check_timings/.set_timings functions.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With this we can eliminate some duplicate code in panel drivers.
Also lgphilips-lb035q02, nec-nl8048hl11-01b, picodlp and
tpo-td043mtea1 gain support of reading timings over sysfs.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the size of memory region that is being set up is the same as before,
we don't have to do memory and layer busy checks.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since any power on stabilisation delay for the supply itself should be
taken care of transparently by the regulator API when the regulator is
enabled the additional delay that the TPO-TD03MTEA1 driver adds after
that returned should be due to the requirements of the device itself
rather than the supply (the delay is also suspicously long for one for
a regulator to ramp). Correct the comment to avoid misleading people
taking this code as a reference.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It is possible for regulator_enable() to fail and if it does fail that's
generally a bad sign for anything we try to do with the hardware afterwards
so check for and immediately return an error if regulator_enable() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It is possible for regulator_enable() to fail and if it does fail that's
generally a bad sign for anything we try to do with the hardware afterwards
so check for and immediately return an error if regulator_enable() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TAAL driver contains some regulator support which is currently unused
(the code is there but the one panel supported by the driver doesn't have
any regulators provided). This code mostly looks like an open coded
version of the regulator core bulk API.
The only additional feature is that a voltage range can be set once when
the device is opened, though this is never varied at runtime. The general
expectation is that if the device is not actively managing the voltage of
the device (eg, doing DVFS) then any configuration will be done using the
constraints rather than by drivers, saving them code and ensuring that
they work well with systems where the voltage is not configurable.
If systems are added needing regulator support this can be added back in,
though it should be based on core features rather than open coding things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For some OMAP versions the TRM says that the pixel clock from DISPC can
be used as an input clock for DSI PLL, instead of the default, which is
sysclk. For some OMAP versions the bits affecting this are marked as
reserved. This feature has never been tested, so it's unknown if the HW
even works, and has never been used.
To clean things up, this patch removes the functionality. This should
not affect any board.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most of the DSS clocks have restrictions on their frequency based on the
OPP in use. For example, maximum frequency for a clock may be 180MHz in
OPP100, but 90MHz in OPP50. This means that when a high enough pixel
clock or function clock is required, we need to use OPP100.
However, there's currently no way in the PM framework to make that kind
of request. The closest we get is to ask for very high bus throughput
from the PM framework, which should effectively force OPP100.
This patch is a simple version for handling the problem. Instead of
asking for OPP100 only when needed, this patch asks for OPP100 whenever
DSS is active. This obviously is not an optimal solution for cases with
small displays where OPP50 would work just fine. However, a proper
solution is a complex one, and this patch is a short term solution for
the problem.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
We do the dss driver registration in a rather strange way: we have the
higher level omapdss driver, and we use that driver's probe function to
register the drivers for the rest of the dss devices.
There doesn't seem to be any reason for that, and additionally the
soon-to-be-merged patch "ARM: OMAP: omap_device: remove
omap_device_parent" will break omapdss initialization with the current
registration model.
This patch changes the registration for all drivers to happen at the
same place, in the init of the module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'next/cleanup-exynos-clock' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
(includes an update to v3.3-rc6)
Currently the shadow-dirty flags for manual update displays is cleared
in the apply_irq_handler when an update has finished. This is not
correct, as the shadow registers are taken into use (i.e. after that
they are not dirty) when the update is started.
Move the mgr_clear_shadow_dirty() call from apply_irq_handler to
dss_mgr_start_update() to fix this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These are no longer needed with the recent iomap.h
changes.
Reported-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
wait_pending_extra_info_updates() currently does a hacky second check
for extra_info_update_ongoing() at the end of the function to show a
warning if extra_info update is still ongoing. The call to
extra_info_update_ongoing() should really be inside spinlock, but that's
a bit heavy just for verification.
Rather than that, check the return value of the
wait_for_completion_timeout() and print an error if it has timeouted or
returned an error.
Even better would be to return the error value and act on it in the
callers of wait_pending_extra_info_updates. However, it's not clear what
the callers should do in case of an error, as the error should only
happen if there's a bug in the driver or the HW. So we'll just print the
warning for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If DSS suspends within the functions dss_mgr_wait_for_go(),
dss_mgr_wait_for_go_ovl() or dss_mgr_wait_for_vsync(). It may lose it's clock
and lead to a register access failure.
Request runtime_pm around these functions.
[archit@ti.com: Moved runtime_pm calls to wait_for_go/vsync functions rather
then calling them from omap_dispc_wait_for_irq_interruptible_timeout()]
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
coef3_M8 had an incorrect phase with 50% more intensity. This resulted in
banding on slightly down/upscaled images. Fixed a rounding error in coef5_M9.
Also removed ARRAY_LEN macro as ARRAY_SIZE is the standard linux one.
Signed-off-by: Lajos Molnar <lajos@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add missing but supported color formats for GFX pipeline in dss features:
RGBX16-4444, RGBA16-4444 and XRGB16-1555.
In dispc_ovl_set_color_mode():
- Remove unsupported modes on GFX pipeline: YUV2 and UYVY. Replace these by
missing modes supported by GFX pipelines: RGBX16-4444 and RGBA16-4444.
- Fix swapped modes on VID pipelines: RGBX16-4444 and XRGB16-4444.
Signed-off-by: Lajos Molnar <lajos@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While calculating regm and regmf value add using M2 divider in
the equation.
Formula for calculating:
Output clock on digital core domain:
CLKOUT = (M / (N+1))*CLKINP*(1/M2)
Internal oscillator output clock on internal LDO domain:
CLKDCOLDO = (M / (N+1))*CLKINP
The current code when allows variable M2 values as input
ignores using M2 divider values in calculation of regm and regmf.
so fix it by using M2 in calculation although the default value for
M2 is 1.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ovl->enable/disable are meant to be synchronous so that they can handle
the configuration of fifo sizes. The current kernel doesn't configure
fifo sizes yet, and so the code doesn't need to block to function (from
omapdss driver's perspective).
However, for the users of omapdss a non-blocking ovl->disable is
confusing, because they don't know when the memory area is not used
any more.
Furthermore, when the fifo size configuration is added in the next merge
window, the change from non-blocking to blocking could cause side
effects to the users of omapdss. So by making the functions block
already will keep them behaving in the same manner.
And, while not the main purpose of this patch, this will also remove the
compile warning:
drivers/video/omap2/dss/apply.c:350: warning:
'wait_pending_extra_info_updates' defined but not used
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
panel-dvi uses i2c, but the Kconfig didn't have dependency on I2C. Add
it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix L4_EMU_34XX_BASE error after iomap changes
ARM: OMAP2+: Limit omap_read/write usage to legacy USB drivers
ARM: OMAP: Remove plat/io.h by splitting it into mach/io.h and mach/hardware.h
ARM: OMAP2+: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move 16xx GPIO system clock to platform init code
ARM: OMAP: Move omap_init_consistent_dma_size() to local common.h
ARM: OMAP2+: Move SDRC related functions from io.h into local common.h
ARM: OMAP2+: Drop DISPC L3 firewall code
ARM: OMAP2xxx: PM: remove obsolete timer disable code in the suspend path
ARM: OMAP: McSPI: Remove unused flag from struct omap2_mcspi_device_config
(update to latest rmk/for-arm-soc branch)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is only needed when using SRAM for framebuffer,
and the support for SRAM framebuffer is about to get
removed.
Otherwise we cannot move most of plat/io.h to be a local
iomap.h for mach-omap2.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
The "OMAPDSS: HDMI: PHY burnout fix" commit switched the HDMI driver
over to using a GPIO for plug detect. Unfortunately the ->detect()
method was not also updated, causing HDMI to no longer work for the
omapdrm driver (because it would actually check if a connection was
detected before attempting to enable display).
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For DSS clock domain to transition from idle to active state. It's necessary
to enable the optional clock DSS_FCLK before we enable the module using the
MODULEMODE bits in the clock domain's CM_DSS_DSS_CLKCTRL register.
This sequence was not followed correctly for the 'dss_hdmi' hwmod and it led
to DSS clock domain not getting out of idle when pm_runtime_get_sync() was
called for hdmi's platform device.
Since the clock domain failed to change it's state to active, the hwmod code
disables any clocks it had enabled before for this hwmod. This led to the clock
'dss_48mhz_clk' gettind disabled.
When hdmi's runtime_resume() op is called, the call to dss_runtime_get()
correctly enables the DSS clock domain this time. However, the clock
'dss_48mhz_clk' is needed for HDMI's PHY to function correctly. Since it was
disabled previously, the driver fails when it tries to enable HDMI's PHY.
Fix this for now by ensuring that dss_runtime_get() is called before we call
pm_runtime_get_sync() for hdmi's platform device. A correct fix for later would
be to modify the DSS related hwmod's mainclks, and also some changes in how
opt clocks are handled in the DSS driver.
This fixes the issue of HDMI not working when it's the default display. The
issue is not seen if any other display is already enabled as the first display
would have correctly enabled the DSS clockdomain.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb driver used platform_data to get fb memory areas and formats
defined by the board file.
This patch removes omapfb's (both old and new omapfb) use of the
memory data in platform_data, because:
- No board uses them currently
- It's not board file's job to define things like amount of default
framebuffer memory. These should come from the bootloader via command
line parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.
This patch removes the use of SRAM as video ram for the omapdss driver
to simplify memory handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The MCLK mode defines a factor to divide the clock that is used to
generate the Audio Clock Regeneration packets, MCLK.
The divisor is not used when the CTS value is calculated by HW.
When the value is calculated by SW, it depends on the silicon
revision.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the MCLK is used to drive the Audio Clock Regeneration packets,
the initialization procedure is to set ACR_CTRL[2] to 0 and then
back again to 1. Also, devices that do not support the MCLK, use
the TMDS clock directly by leaving ACR_CTRL[2] set to 0.
The MLCK clock divisor, mclk_mode, is configured only if MLCK
is used. Such configuration is no longer related to the CTS mode
as in some silicon revisions CTS SW-mode is used along with the MCLK.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Certain OMAP4 revisions (i.e., 4430 ES2.3, 4460, and 4470) use
a pseudo clock (generated from the TMDS clock), MCLK, to drive the
generation of Audio Clock Regeneration packets. Other devices
(i.e., 4430 ES2.[0,2]) use the TMDS clock directly.
This patch adds a new DSS feature for MCLK support. It also rearranges
the omap_dss_features structures to reflect the devices supporting it.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Over time better gamma has been determined and tuned with some
equipment so update the defaults. From subjective point of view
dark shades should be better visible.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
During system suspend, at the time DSS is being suspended, SPI is
already suspended and it's clocks are cut. Because of this trying to
communicate with the LCD controller results in a deadlock.
To fix this, split out LCD programming parts of display enable/disable
functions and perform them from SPI PM callbacks instead when system is
being suspended. If the display is just being enabled/disabled, do it
from DSS callbacks as before.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With AVI infoframe various parameters of video stream such as
aspect ratio, quantization range, videocode etc will be indicated
from source to sink.Thus AVI information needs to be set/accessed
by the middle ware based on the video content.
Thus this parameter is now moved to the ip_data structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for Innolux AT080TN52 800x600 panel.
Tested with AM3517 based board.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The calculation of required DISPC_FCLK for downscaling is done by multplying the
pixel clock with an integer factor. This isn't true for OMAP4 where the required
clock is calculated using the exact ratio of downscaling done.
Fix this calculation for OMAP4. Also, do a minor clean up of calc_fclk().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The number of dss_feat_id members has increased to a large value, the current
way of assigning a subset of these features (for a particular OMAP) as a mask
is no longer feasible.
Maintain the subset of features supported as lists. Make the function
dss_has_feature() traverse through this list.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that dss is using devm_ functions for allocation in probe functions,
small reordering of the allocations allows us to clean up the probe
functions more.
This patch moves "unmanaged" allocations after the managed ones, and
uses plain returns instead of gotos where possible. This lets us remove
a bunch of goto labels, simplifying the probe's error handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
This patch converts the drivers in drivers/video/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Roger Quadros <roger.quadros@nokia.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.
Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.
This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit ba02fa37de disabled the
venc driver registration on OMAP4. Since the driver never gets
probed/initialised your get a dereferenceed NULL pointer if you
try to get info from /sys/kernel/debug/omapdss/venc
Return info message about disabled venc if venc_dump_regs() gets called.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Due to changes in struct hdmi_config, the pixel clock has to be obtained
differently.
The pixel clock is needed to calculate the CTS value as defined in the
HDMI specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
code and mode parameters are already a part of the ip_data structure
so no need to keep the same parameters again in hdmi global structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change the timing match logic, Instead of the statically mapped method
to get the corresponding timings for a given code and mode, move to a
simpler array indexed method. It will help to scale up to add more
timings when needed.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the vsync polarity, hsync polarity, interlace to hdmi_video_timings.
Remove the now duplicate structure hdmi_timings.
update the static table structure in HDMI with CEA/VESA code and mode.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
video interface structure is a duplicate structure with parameters which are
already present in ip_data config structure, Thus removing the structure and
modifying corresponding code.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Take fifo merge into use by implementing a rather naive fifo merge
threshold calculation: keep the low threshold always the same, but
increase the high threshold when fifo merge is used.
This should greatly increase the time between pixel data fetches from
SDRAM, as the usable fifo size is much larger. However, it probably
won't help for fifo underflows, as the low threshols is kept the same.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fifo thresholds are calculated using bytes, but the debug print prints
values in buffer units. Change the prints to use bytes to be in line
with the calculations, and also to print in the same units on all OMAPs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add fifo-merge support. This is done mainly in four functions:
mgr_enable/disable and ovl_enable/disable. These are the functions where
overlays are taken into and out of active use.
The process to enable and disable fifo-merge is not simple. We need to
do it in steps, waiting in between for certain settings to be taken into
use, and continuing after that. The reason for this is that fifo-merge
is a common thing for all managers/overlays, and its use must be
synchronized.
As an example, when we disable an overlay, we first set the overlay as
disabled, then wait until the overlay is actually disabled in the HW,
and only after that we may re-configure the fifos, possibly taking
fifo-merge into use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add mechanism to set/unset the DISPC fifo-merge:
Add new fields to dss_data, fifo_merge and fifo_merge_dirty. These are
similar to the other info/dirty flags in ovl_priv_data and ovl_mgr_data,
but fifo merge is a common attribute to all managers and thus outside
the ovl_mgr_data.
The fifo-merge field is used in the dss_write_regs_common, which handles
writing the register.
dss_apply_fifo_merge() can be used to set/unset the fifo merge field in
the dss_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add feature flag for fifo merge. OMAP2 doesn't contain fifo merge, later
OMAPs do.
dispc_enable_fifomerge() checks for the flag when called, and gives a
WARN if fifo merge is being enabled when it is not supported.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
dd data for the OrtusTech COM43H4M10XTC display to the
generic_dpi_panel driver.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for Microtip Technologies' UMSH-8173MD 800x480
RGB TFT panel. Tested with an OMAP3 board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[tomi.valkeinen@ti.com: changed the panel name string]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function hdmi_audio_trigger is a callback used by ASoC to stop/start
HDMI audio. Also, it does not perform IP-specific configuration directly.
Hence, it should be placed in the general portion of the HDMI driver,
along with the other ASoC callbacks.
Also, make this function static.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to separate clearly IP-specific code from general DSS code,
a function for OMAP4 audio enable is created. This function is
included in the HDMI IP ops to align with the current implementation
of the DSS HDMI driver. This function is to be used by the ASoC
HDMI audio codec.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These functions require access to IP-secific data. However, it is not possible
to pass such data as a function argument as such functions have a specific
signature specified by ASoC. Instead, they will have access to the IP-specific
data by calling snd_soc_codec_get_drvdata. The codec driver data is set
at probe time.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Under the new DSS architecture for HDMI, there is a clear separation
between general DSS code and HDMI IP-specific data. Functions
that require access to the HDMI driver IP-specific data receive an
hdmi_ip_data structure. The ASoC codec require access to such
IP-specific data. Then, instead of accessing it directly, it will be
passed as codec driver data. This also helps to have a clear separation
between DSS and ASoC portions of the code.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clock requirements for scaling in OMAP2, OMAP3 and OMAP4 are different. In
OMAP2 and OMAP3 the required clock rate is a function of pixel clock, vertical
downscale ratio and horizontal downscale ratio whereas in OMAP4 it is a
function of pixel clock and horizontal downscale ratio only. Selection of 3-tap
vs 5-tap coefficients depends on clock rate line buffer width in OMAP3 whereas
in OMAP4 it is independent of clock rate and line buffer width. In OMAP2 3-tap
for vertical and 5-tap for horizontal scaling is used. In OMAP4 5-tap is used
both for horizontal and vertical scaling for better performance. Also, the
number and width of line buffers differs in OMAP3 and OMAP4.
So, clock functions have been fined tuned for OMAP3 and support has been added
added for OMAP4. This code has been tested on OMAP2, OMAP3 and OMAP4, and
scaling issues due to clock errors have been resolved.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FIR coefficients present in kernel are being updated to new coefficients
consisting of 24 coefficient tables, with 12 each for 3 tap and 5 tap scenario,
which are chosen on the basis of DISPC up/downsampling filters M value. M is
the inverse of low pass cut off frequency of the sampling filter. For vertical
scaling 3 tap or 5 tap tables are used based on the clock rate and width of
the line buffer whereas in OMAP2 3 tap is always used. For horizontal scaling
however 5 tap tables are always used.
New coefficients and the corresponding logic have been tested on OMAP2, OMAP3
and OMAP4. Horizontal and vertical scaling worked fine except for some 3 tap
vs 5 tap issue during vertical upscaling and clock failing issues which is
acknowledged in the next patch. Vertical upscaling was found to perform better
under 5 taps. The 24 coefficient tables have been moved to another file
dispc_coefs.c for proper maintainance.
This code is written based on code written by Lajos Molnar <lajos@ti.com> in
Android Kernel for scaling. Lajos Molnar <lajos@ti.com> had fine tuned the FIR
coefficient selection process and reduced outliness and blockiness around
images when upscaling more than 2 times.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
extra_info_update_ongoing() goes through all overlays, but doesn't check
if the overlay is connected to a manager. This leads to a crash whenever
an overlay has been detached.
Add a check to skip the non-connected overlays.
Reported-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make PICODLP driver on OMAP2_DSS_DPI since it is the display interface it uses.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display state parameter of omap_dss_device struct is not being set correctly
in the panel driver NEC panel driver panel-nec-nl8048hl11-01b.c. Set the correct
states in the panel's enable/disable/suspend/resume functions.
CC: Erik Gilling <konkers@android.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock names of DSI_PLL_HSDIV_DISPC and DSI_PLL_HSDIV_DSI was made
dynamic based on the current value of DISPC and DSI FCLK sources. This
doesn't need to be done since we are just interested in the clock names,
and not the current clock sources for DISPC and DSI FCLKs.
Use only the generic and omap specific names for the DSI PLL's HSDIV
clocks.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions dss_ovl_simple_check() and dss_mgr_simple_check() are not
really part of the apply mechanism, and can be moved to overlay.c and
manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dispc's error handler tries to disable all outputs when OCP_ERR
happens. However, the code doesn't check if there actually is a display
on each particular output, nor if there's a driver for the display. This
may lead to NULL pointer reference.
Signed-off-by: Rob Clark <rob@ti.com>
[tomi.valkeinen@ti.com: added patch description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions dss_ovl_check, dss_mgr_check_zorder, dss_mgr_check in
apply.c are not really part of the apply mechanism, and can be moved to
overlay.c and manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This resolves the conflict in the
drivers/staging/iio/industrialio-core.c file due to two different
changes made to resolve the same problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Current code will always write fifo threshold values to the register,
even if they are the same as previously. Separate the setting of fifo
fields into a separate function, and only set new values if they are
different than the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently fifo threshold configuration is done per overlay or per
manager. However, when a fifo size configuration is added, we need to
always configure the thresholds for all overlays.
This patch prepares for that by changing the fifo threshold
configuration to always handle all overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When we are enabling an overlay, there's a point in time when the
overlay is not actually enabled yet (nor do we want it to be enabled),
but we do want to check if the configuration for the overlay is valid,
and to calculate correct fifo thresholds for the soon-to-be-enabled
overlay.
Current code handled this in a hacky way, setting op->enabled to true
temporarily when calling functions that need to consider the state when
the overlay is enabled.
This patch makes this a bit cleaner, adding "enabling" field, which is
set when the overlay is not yet enabled but should be considered in the
checks and calculations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently dss_write_regs() implicitely sets the GO bits for all managers
with shadow dirty flags set. This is a bit misleading, as one does not
presume "write registers" function to also set the GO bit.
Thus this patch splits the setting of GO bits into a separate function,
dss_set_go_bits, which is used after writing the registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In the apply irq handler the code currently clears the shadow dirty
flags whenever the manager in question is not busy (i.e. GO bit is
down). However, this is not quite right, as the GO bit may have never
been set.
While not done in the current code, the above would cause bug in
scenario where the registers are written, and thus shadow_dirty flag is
set, but the GO bit will be set only later. In this case the
shadow_dirty flags would be cleared, even if the HW is not using the new
configurations.
This patch fixes the issue by clearing the shadow flags only when the GO
bit is clear, and the GO bit had been set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
need_isr() should return true whenever there's work that needs to be
handled in the VSYNC/FRAMEDONE irq handler. However, need_isr() is
missing some cases where we need the irq handler.
This patch adds checks for shadow dirty flags, so that the irq handler
is started/kept running while shadow dirty flags are set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
extra_info_update_ongoing() skipped checks for overlays that were marked
as disabled. This doesn't work, as the enable status of an overlay is in
the extra_info group, and thus extra_info_update_ongoing() reports false
when we are disabling an overlay. This causes
wait_pending_extra_info_updates() to not wait for the ongoing overlay
disable.
This patch changes extra_info_update_ongoing() to check the state of
overlays marked as disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that dss_mgr_enable returns an error value, check it in all the
places dss_mgr_enable is used, and bail out properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add checks for overlay and manager settings. The checks are a bit
complex, as we need to observe the bigger picture instead of overlays
and managers independently. Things like the used display and the zorder
of other overlays affect the validity of the settings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_mgr_simple_check() which is used to check the validity of
certain manager attributes. Only attributes that can be checked
independently, without knowing the display being used, is done here
(thus "simple").
We can use this function in dss_mgr_set_info().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_ovl_simple_check() which is used to check the validity of
certain overlay attributes. Only attributes that can be checked
independently, without knowing the display being used, is done here
(thus "simple").
We can use this function in dss_ovl_set_info().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
apply.c no longer touches any registers if an output is not enabled.
This means that we don't need to do dispc_runtime_get() anymore, and the
calls can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add wait_pending_extra_info_updates() function which can be used to wait
until any extra_info changes have been taken into use by the hardware.
This can be only called when holding the apply mutex, so that other
threads cannot insert new extra_info changes.
This will be used to handle fifo-configurations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add checks to dss_mgr_enable, dss_mgr_disable, dss_ovl_enable,
dss_ovl_disable that check if the state is already the same as given in
the parameters, and exit if so.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a helper function dss_apply_ovl_enable(), which is similar to the
main apply() function: dss_apply_ovl_enable() applies the given overlay
enable-status to ovl_priv_data, and sets the dirty flag.
The difference between the helper function and the previous direct use
of the fields is that the helper function will not do anything if the
enable state is already the same as given in the parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_overlay_manager contains device_changed field, which no longer has
any use. So remove the field and the few places where it is touched.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rename ovl_priv_data's and mgr_priv_data's dirty and shadow_dirty fields
to info_dirty and shadow_info_dirty to better reflect what they mean.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Setting overlay's fifo thresholds is currently handled at the same time
as other overlay attributes. This is not right, as the normal attributes
should only affect one overlay and manager, but changing the fifo
thresholds are needed in cases like fifo-merge, where multiple managers
are affected.
This patch moves the channel field into the "extra_info" set, handled
together with channel and enabled-status.
This also lets us to calculate the fifos only when needed, specifically,
when an overlay or a manager is enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Setting overlay's output channel is currently handled at the same time
as other overlay attributes. This is not right, as the normal attributes
should only affect one overlay and manager, but changing the channel
affects two managers.
This patch moves the channel field into the "extra_info" set, handled
together with enabled-status.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlayr contains info and info_dirty fields, both of which
should be internal to apply.c.
This patch moves those fields into ovl_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlay_manager contains info and info_dirty fields, both of
which should be internal to apply.c.
This patch moves those fields into mgr_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a helper function mgr_clear_shadow_dirty(), which clears the
shadow_dirty flags for the given manager and for the overlays on that
manager.
This lets us simplify the code in the dss_apply_irq_handler().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "updating" flag to mgr_priv_data, which is used to track whether the
manager is currently actively working, i.e. updating the screen.
For auto-update displays updating is always true when the display is
enabled, but for manual update displays the flag is true only during
frame transfers.
The flag is used to manage registers properly, for example when updating
is false and a register for a manager is written, there's no need to set
shadow_dirty flag nor set the GO bit, as the settings will be taken into
use by the HW automatically when the output is enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dispc_mgr_get_framedone_irq() which returns the irq number for
FRAMEDONE for the given channel.
Note that the function returns always 0 for DIGIT channel, even if OMAP4
does have FRAMEDONE_TV interrupt. The reason for this is that this
function is currently used only to track manual updates, and thus
FRAMEDONE_TV is not needed.
If there's need in the future to also get the FRAMEDONE_TV this needs
revisiting. However, as FRAMEDONE_TV doesn't exist on OMAP2/3, the use
of this function for that purpose needs some extra code to handle the
OMAP2/3 case.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions writing to the DISPC registers in apply.c are more complex
than needed. This patch cleans things up.
Two helper functions are added: need_isr(), which returns if an isr for
VSYNC is needed, and need_go(), which tells if there has been a write to
the shadow registers and we need to set the GO bit.
The functions that call the actual dispc write functions will set the
dirty and shadow_dirty flags themselves, instead of that being done on
the caller side. The writing functions also check if the dirty flag is
even set, and return immediately if not.
This allows us to clean up dss_write_regs().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlays are currently enabled and disabled with a boolean in the struct
omap_overlay_info. The overlay info is set with ovl->set_overlay_info(),
and made into use with mgr->apply().
This doesn't work properly, as the enable/disable status may affect also
other overlays, for example when using fifo-merge. Thus the enabling and
disabling of the overlay needs to be done outside the normal overlay
configuration.
This patch achieves that by doing the following things:
1) Add function pointers to struct omap_overlay: enable(), disable() and
is_enabled(). These are used to do the obvious. The functions may block.
2) Move the "enabled" field from struct omap_overlay to ovl_priv_data.
3) Add a new route for settings to be applied to the HW, called
"extra_info". The status of the normal info and extra_info are tracked
separately.
The point here is to allow the normal info to be changed and
applied in non-blocking matter, whereas the extra_info can only be
changed when holding the mutex. This makes it possible to, for example,
set the overlay enable flag, apply it, and wait until the HW has taken
the flag into use.
This is not possible if the enable flag would be in the normal info, as
a new value for the flag could be set at any time from the users of
omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a new field to mgr_priv data, "busy", which is used to track the
status of GO bit with the manager. As manual update displays never use
the GO bit, the field is always false for managers used for manual
update displays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlay_manager contains "enabled"-field, used to track if
the manager is enabled or not. This field should be internal to apply.c.
This patch moves the field to mgr_priv_data, and applies the necessary
locking when accessing the field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current code uses dsi_video_mode_enable/disable functions to
enable/disable DISPC output for video mode displays. For command mode
displays we have no notion in the DISPC side of whether the panel is
enabled, except when a dss_mgr_start_update() call is made.
However, to properly maintain the DISPC state in apply.c, we need to
know if a manager used for a manual update display is currently in use.
This patch achieves that by changing dsi_video_mode_enable/disable to
dsi_enable/disable_video_output, which is called by both video and
command mode displays. For video mode displays it starts the actual
pixel stream, as it did before. For command mode displays it doesn't do
anything else than mark that the manager is currently in use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions in apply.c, called mostly via function pointers in overlay
and overlay_manager structs, will be divided into two groups. The other
group will not sleep and can be called from interrupts, and the other
group may sleep.
The idea is that the non-sleeping functions may only change certain
settings in overlays and managers, and those settings may only affect
the particular overlay/manager. For example, set the base address of the
overlay.
The blocking functions, however, will handle more complex configuration
changes. For example, when an overlay is enabled and fifo-merge feature
is used, we need to do the enable in multiple steps, waiting in between,
and the change affects multiple overlays and managers.
apply.c already contains a spinlock, which has been used to protect
(badly) the dss_data. This patch adds locks/unlocks of the spinlock to
the missing places, and the lock should now properly protect dss_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions in apply.c, called mostly via function pointers in overlay
and overlay_manager structs, will be divided into two groups. The first
group will not sleep and can be called from interrupts, and the second
group may sleep.
The idea is that the non-sleeping functions may only change certain
settings in overlays and managers, and those settings may only affect
the particular overlay/manager. For example, set the base address of the
overlay.
The blocking functions, however, will handle more complex configuration
changes. For example, when an overlay is enabled and fifo-merge feature
is used, we need to do the enable in multiple steps, waiting in between,
and the change affects multiple overlays and managers.
This patch adds the mutex which is used in the blocking functions to
have exclusive access to overlays and overlay managers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS currently tries to check that the given overlay and overlay manager
settings are acceptable, but the code does not work quite properly.
Things may change between the check and the actual use of the settings.
Furthermore, the following patches will rewrite how settings are
configured and managed, and trying to keep the (broken) settings
checking working during the rewrite would be very difficult.
This patch removes the checking code, and a working version of checking
will be added back after the settings rewrite has been done.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
apply.c will handle the management of dispc in the future patches. This
patch moves overlay manager related functions to apply.c so that they
will have access to the private data and functions of apply.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
