Tegra's I2C2 controller can be routed to either the PTA or DDC pin group
on Seaboard. Define the pinctrl state nodes required to allow runtime
control of this routing. Instantiate a pinctrl-i2cmux I2C bus mux that
uses these pinctrl states.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
mx23-olinuxino is a low cost board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Device's regulator matches their hardware counterparts with the
property "regulator-compatible" of each child regulator node in
place of the child node name.
Add the property "regulator-compatible" for each regulator with
their hardware counterpart's name.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add Variscite OMAP4 System-On-Modeule support
Signed-off-by: Uri Yosef <uri.y@variscite.com>
[tony@atomide.com: updated to use disabled instead of disable]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM335X BeagleBone device tree source (am335x-evm.dts) file
to use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM335X EVM device tree source (am335x-evm.dts) file to
use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree source include file for the AM33XX SoC family.
An additional .dtsi file is created to describe the generic
AM33XX CPU module like intc, ocp.
Actual selection of available peripherals is handled in seperate
.dts files using this am33xx.dtsi generic header file.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing properties for fec, phy-supply, phy-reset-gpios and
phy-reset-duration, which are required by fec driver for successfully
probe fec from device tree, if bootloader hasn't set those things up.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add vmmc-supply for mmc device, so that the power to mmc slot can be
turned on by mmc driver if bootloader hasn't done it.
Also remove "okay" status for mmc1/ssp1, as the device has pin conflict
with gpmi-nand. Actually the device is already disabled since the
mxs-mmc driver adopts pinctrl support because there is no pinctrl setup
for the device in dts. Make this explicit by removing "okay" status.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The 8-bit mode mmc has pin conflicts with display. Let's use 4-bit
mode by default, so that display can be enabled together later.
Also add vmmc-supply for mmc device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Before gpio_request can directly ask pinctrl system to configure the
requested pin into gpio mode, we use "hog" entry (pinctrl state of
pin controller itself) to configure gpios.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add comments for pinmux-ids so that we do not have to keep looking at
Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt to read
all these pinmux-ids.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Replace "gpmi" with "gpmi-nand" to get the
GPMI interface probing with DT instead of
failing to get clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
CC: Dong Aisheng <b29396@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
add gpmi-nand device tree support.
add gpmi-nand pinctrl support.
Also enable the gpmi support for mx28-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add auxdata to instantiate the PWFM controller from a device tree,
include the corresponding nodes in the dtsi files for Tegra 20 and
Tegra 30 and add binding documentation.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add a third cell to define irq priority.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add support for TWL4030, which is interfaced on i2c1 bus.
Also add clock frequencies for other i2c instances (2 & 3)
required for client-device exist on OMAP3EVM board.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM3517 EVM (AM3517/05) DTS file to use the omap3.dtsi SoC file,
along with memory node and basic i2c information.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Simple DTS file for OMAP2420H4 board adding memory information to allow
device-tree testing on an OMAP2420. OMAP2420H4 board has 64MB of RAM.
Verified that kernel boots with DT using a simple RAMDISK file-system on
OMAP2420H4.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the DT node for gpmi nand.
Add the pinmux support for gpmi nand.
The gpmi nand may conflicts with other modules, such as MMC.
So we do not enable the gpmi nand for mx6q-arm2 board, just add the
node for the board.
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJP7BHOAAoJEMePsQ0LvSpLCrcP/RwJliq2ITgQMEj3N2BbDkKP
kvS63qYv+QqH+mhGm/RFrmB/p3LSxgOkgdQByavfsQnsE0v5+FYjDnXAB3tvUVHI
Tv9vSJLIAgC9n4Z8pdJ8u71VGu8XVYnGnCKNz6UhVfHX8Q5BEs01eSPw3wgDVTIq
gKpMHaeNdi4Atkh2KmxyLwEBF9QC+vSNxMtkqcYbT5faBrqOEKeLz5igG8+VQBTU
RNeUOHb99+Rf/H2eRsynwMgX63xMzh7hSwW2GAJ5O7+uoMLmdPuI7MUAQR/zcPzQ
gmFUb1yKkmvu9OKtNR+3VCgGGlvvhaJBwTFJj9IL10xrj4LnDlA3N9bC9vwHG8zw
0YbrPA2iLU6ufdmLf5rANQFJL3ttg65MZTsjA8q3tjE04QkJncRpDtzr89dQYw/C
hv3vqCYpo0b2UCMPcyf4pUR5rzzHjPiM4Np9GEj3Ak1puUASwNXGTvXWusWXND9i
ixcFxd6LppyIa8FxMKXONEGaeNKbp+T63EugBCDEeCCWkXXQQGXU54xWy7w939ib
pvDtk1+ZqHC5rzPfuNokD+H95W3pc5AYr2pPjW8fctH6Wp9dFZV8sg77pgbenS/E
u2UX5N7rlqtj/Km7fJgy6h3EUVg8ky6W5nMtF2Jad8D89FOZHoSRAICPA4dIxTYl
hvv7kdtT23AqZKbxQUNu
=2b0z
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-d-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes-non-critical
Some OMAP AM35xx fixes.
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
Add support for L2 ECC on Calxeda highbank platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for memory controller on Calxeda Highbank platforms. Highbank
platforms support a single 4GB mini-DIMM with 1-bit correction and 2-bit
detection.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nothing very controversial in here. Most of the fixes are for OMAP this time
around, with some orion/kirkwood and a tegra patch mixed in.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6Ahb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Nothing very controversial in here. Most of the fixes are for OMAP
this time around, with some orion/kirkwood and a tegra patch mixed in."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion: Fix Virtual/Physical mixup with watchdog
ARM: Kirkwood: clk_register_gate_fn: add fn assignment
ARM: Orion5x - Restore parts of io.h, with rework
ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
ARM: OMAP2+: mux: fix sparse warning
ARM: OMAP2+: CM: increase the module disable timeout
ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
ARM: tegra: make tegra_cpu_reset_handler_enable() __init
ARM: OMAP: PM: Lock clocks list while generating summary
ARM: iconnect: Remove include of removed linux/spi/orion_spi.h
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=cMPJ
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here are a few fixes with the biggest one being fix for Beagle DVI
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier."
* tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.
Just the OMAP part here, the rest goes via other patches and trees.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.
Just the tegra part here. Everything else goes via other patches and trees.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Most ARM ${board}.dts files are already named ${soc}-${board}.dts. This
change modifies the Tegra board files to be named the same way for
consistency.
Once a related change is made in U-Boot, this will cause both U-Boot and
the kernel to use the same names for the .dts files and SoC identifiers,
thus allowing U-Boot's recently added "soc" and "board" environment
variables to be used to construct the name of Tegra .dtb files, and hence
allow board-generic U-Boot bootcmd scripts to be written.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
When booting with device-tree on an OMAP2420H4, the kernel is hanging when
initialising the interrupts and following kernel dumps is seen ...
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at arch/arm/mach-omap2/irq.c:271 omap_intc_of_init+0x50/0xb4()
[ 0.000000] unable to get intc registers
[ 0.000000] Modules linked in:
[ 0.000000] [<c001befc>] (unwind_backtrace+0x0/0xf4) from [<c0040c34>] (warn_slowpath_common+0x4c/0x64)
[ 0.000000] [<c0040c34>] (warn_slowpath_common+0x4c/0x64) from [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40)
[ 0.000000] [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40) from [<c066b8a4>] (omap_intc_of_init+0x50/0xb4)
[ 0.000000] [<c066b8a4>] (omap_intc_of_init+0x50/0xb4) from [<c0688b70>] (of_irq_init+0x144/0x288)
[ 0.000000] [<c0688b70>] (of_irq_init+0x144/0x288) from [<c0663294>] (init_IRQ+0x14/0x1c)
[ 0.000000] [<c0663294>] (init_IRQ+0x14/0x1c) from [<c06607fc>] (start_kernel+0x198/0x304)
[ 0.000000] [<c06607fc>] (start_kernel+0x198/0x304) from [<80008044>] (0x80008044)
[ 0.000000] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.000000] of_irq_init: children remain, but no parents
The OMAP2 interrupt controller binding is missing the number of interrupts and
interrupt controller register address. Adding these fixes the problem.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the reg, cs-gpios and max-frequencies that are needed for spi
device registry in phy3250.
Adds also the pl022 internal transfers details via dt
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.
Signed-off-by: Roland Stigge <stigge@antcom.de>
This patch fixes the DTS files for the High Speed UARTs 1, 2 and 7 of the
LPC32xx SoC, adjusting the compatible strings, adding interrupts and status
configuration. On the PHY3250 reference board, UART2 is enabled.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch switches from static serial driver initialization to devicetree
configuration. This way, the Standard UARTs of the LPC32xx SoC can be enabled
individually via DT.
E.g., instead of Kconfig configuration, the phy3250.dts activates
UARTs 3 and 5.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch connects the lpc32xx-key driver to the LPC32xx platform (via
lpc32xx.dtsi), and more specifically to the reference board via its dts file.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
There is another reference/development board for the LPC32xx SoC (besides the
Phytec 3250): The Embedded Artists LPC3250 board. This patch adds a default dts
file for it.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch takes into account that the MTD NAND MLC controller needs more
registers, located actually before the previously allocated memory range,
already starting at 200a8000 instead of 200b0000.
Further, the interrupt for the controller is configured.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch adds necessary NAND flash timings to the board specific dts file of
the PHY3250 reference board of the LPC32xx SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Use a more plain english name.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
[swarren: also rename the node in tegra-seaboard.dts]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use a more plain english name.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
[swarren: remove redundant unit address from tegra30.dtsi change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
The Nomadik GPIO controller now relies on Nomadik pinctrl, however
the pinctrl driver is not currently started by any ux500 platform.
This is requred or GPIOs do not work at all.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we supply the information required to setup regulators successfully
on Snowball and other db8500 variants which use the ab8500 regulators.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a fixed regulator for use by the SMSC911x Ethernet
chip driver into the db8500 Device Tree. It also references other
regulators required by the same device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we inform Device Tree of which regulators are provided by the db8500-
prcmu. This way we can reference some of their consumers directly from the
Device Tree e.g. SMSC911x Ethernet chip.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch applies the correct format requested by the irq
domain. For chained IRQs which use GPIO lines as IRQs, we
stipulate that a two cell request is required. The first cell
contains the requested IRQ and the second can contain flags
pertaining to edge detection and level sensitive values. The
zeroth cell specifies the GPIO controller by use of a phandle.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Apply db8500 related PRCMU Device Tree settings and clean up some formatting
errors. We also remove one of the PRCMU assigned IRQs, as it is currently not
used.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GPIO devicetree binding in 3.5 doesn't register the various LPC32xx GPIO
banks via DT subnodes but always all at once, and changes the gpio referencing
to 3 cells (bank, gpio, flags). This patch adjusts the DTS files to this
binding that was just accepted to the gpio subsystem.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
* late/soc:
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
ARM: EXYNOS: Support suspend and resume for EXYNOS5250
ARM: EXYNOS: Add Clock register list for save and restore
ARM: EXYNOS: Add PMU table for EXYNOS5250
ARM: EXYNOS: Rename of function for pm.c
ARM: EXYNOS: Remove GIC save & restore function
ARM: dts: Add node for interrupt combiner controller on EXYNOS5250
ARM: S3C24XX: add support for second irq set of S3C2416
A few device tree updates and an include file fix for versatile.
* 'vexpress-v3.4' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
+ update to 3.4
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for the spear13xx platform, which has first been under
review a long time ago and finally been completed after generic spear
work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W2Ri
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d6 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit f10590c983 ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
Here is the big staging tree pull request for the 3.5-rc1 merge window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out of
the staging tree, to their respective "real" portions of the kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q8MACgkQMUfUDdst+ymjogCguo8fANFVlPWeZGeoBTL+aQfQ
yTkAoLE0codmh+2SvhulYgyU1Wh6ZDK2
=nJ2F
-----END PGP SIGNATURE-----
Merge tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree changes from Greg Kroah-Hartman:
"Here is the big staging tree pull request for the 3.5-rc1 merge
window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out
of the staging tree, to their respective "real" portions of the
kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up various trivial conflicts, along with a non-trivial one found
in -next and pointed out by Olof Johanssen: a clean - but incorrect -
merge of the arch/arm/boot/dts/at91sam9g20.dtsi file. Fix up manually
as per Stephen Rothwell.
* tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (536 commits)
Staging: bcm: Remove two unused variables from Adapter.h
Staging: bcm: Removes the volatile type definition from Adapter.h
Staging: bcm: Rename all "INT" to "int" in Adapter.h
Staging: bcm: Fix warning: __packed vs. __attribute__((packed)) in Adapter.h
Staging: bcm: Correctly format all comments in Adapter.h
Staging: bcm: Fix all whitespace issues in Adapter.h
Staging: bcm: Properly format braces in Adapter.h
Staging: ipack/bridges/tpci200: remove unneeded casts
Staging: ipack/bridges/tpci200: remove TPCI200_SHORTNAME constant
Staging: ipack: remove board_name and bus_name fields from struct ipack_device
Staging: ipack: improve the register of a bus and a device in the bus.
staging: comedi: cleanup all the comedi_driver 'detach' functions
staging: comedi: remove all 'default N' in Kconfig
staging: line6/config.h: Delete unused header
staging: gdm72xx depends on NET
staging: gdm72xx: Set up parent link in sysfs for gdm72xx devices
staging: drm/omap: initial dmabuf/prime import support
staging: drm/omap: dmabuf/prime mmap support
pstore/ram: Add ECC support
pstore/ram: Switch to persistent_ram routines
...
While we generally attempt to get rid of board specific files and replace
them with device tree based descriptions, a lot of platforms have not
come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination of
DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wkmj
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to
the classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided to
have them all live in one directory.
This also contains updates to existing shmobile soc code as well as some
related board changes due to dependencies.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=5TAz
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull support for new arm SoCs from Olof Johansson:
"Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to the
classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided
to have them all live in one directory.
This also contains updates to existing shmobile soc code as well as
some related board changes due to dependencies."
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
mach-shmobile: Use DT_MACHINE for KZM9D V3
mach-shmobile: Emma Mobile EV2 DT support V3
mach-shmobile: KZM9D board Ethernet support V3
mach-shmobile: Emma Mobile EV2 GPIO support V3
mach-shmobile: Emma Mobile EV2 SMP support V3
mach-shmobile: KZM9D board support V3
mach-shmobile: Emma Mobile EV2 SoC base support V3
gpio: Emma Mobile GPIO driver V2
ARM: mach-shmobile: sh73a0: fixup PINT/IRQ16-IRQ31 irq number conflict
ARM: mach-shmobile: clock-r8a7740: use followparent_recalc on usb24s
ARM: mach-shmobile: clock-r8a7740: add MMCIF clock
ARM: mach-shmobile: clock-r8a7740: add SDHI clock
ARM: mach-shmobile: clock-r8a7740: add USB clock
ARM: mach-shmobile: clock-r8a7740: add FSI clock
ARM: mach-shmobile: r8a7740: cleanup I2C workaround method
ARM: mach-shmobile: r8a7740: add gpio_irq support
ARM: mach-shmobile: sh7372: Add FSI DMAEngine support
ARM / mach-shmobile: Use preset_lpj with calibrate_delay()
ARM: ux500: ioremap differences for DB9540
ARM: ux500: core U9540 support
...
The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game of
booting using device trees, which is a great step forward for them. at91
and spear have pretty much completed this process with a huge amount of
work being put into at91. The other platforms are continuing the process.
We finally start to see the payback on this investment, as new machines
are getting supported purely by adding a .dts source file that can be
completely independent of the kernel source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPueqRAAoJEIwa5zzehBx3AYkP/ibDGGd0qp1gxnxPYowliXcp
lrWP8KB2PVcX/041jwpvsWeHzWT+Gm39ryBfz2L3pq/RiuU0jPPwChKgy1iglE8X
6Rq6sPWkXoDRtyeCuoiaxf1AYuzzAVdzZ0HlPO93tSKgo5eeyZRC5OeebAnrLDCE
SDi8gZx2mm9+j2Dz46gq8QluyswMMbke3fHHHaHUlcP9fKIvFWvEfsn5j+YQ9bSw
DrSIqGOzv6Emn7F6yhFQqxmk86KLnaXDVpAWgjVDhzaPv0rcTzloN6D2Ie2e5Vev
BiRM1zvWn2d9kDk7gpm0t67nguYxsCBl1GNCP1brrncGwt15S10JimYlRhYW+B7u
qgJqMPko3OnONvyl6e8qgIa2M5N4K/mo1i/jfOwFw3+KfUjXqLeio53Ysr4a6tsM
Ev3bEsofNJKA0dlMcVzr7ntL087B6Y8mY3oJsVZji5M0KVfx1Jfn+X1W+l/2KD1H
XWhJrCGa1HlbtSnrD+E91VHGC3M4sEXbbTljMAjHImlU9dGXmmbRMNsqNwkF6qFj
EO2HnFvdN1oK+zEmeAttR1JHxfMdPFnTfmpUf3AiVSjGO//Wltelqx8ibA2Smn7S
xXmzqX/HMhIOYCh81FdvzsK4qRYU5QyOsEJB4G0UjBZ66M1A3T/+vPpWuKsw5bUb
qbnxaaXNsaZjWbbSSrZ4
=7DYv
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
* Added extra regs for A15 VGIC
* Added A15 architected timer node
* Split A5 and A9 TWD nodes into two separate ones for timer
and watchdog; interrupt definitions fixed on the way
* Fixed typo in A5 GIC compatible value
All the changes courtesy of Marc Zyngier.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
* 'emev2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
mach-shmobile: Use DT_MACHINE for KZM9D V3
mach-shmobile: Emma Mobile EV2 DT support V3
mach-shmobile: KZM9D board Ethernet support V3
mach-shmobile: Emma Mobile EV2 GPIO support V3
mach-shmobile: Emma Mobile EV2 SMP support V3
mach-shmobile: KZM9D board support V3
mach-shmobile: Emma Mobile EV2 SoC base support V3
gpio: Emma Mobile GPIO driver V2
EXYNOS5250 includes a interrupt combiner controller that can group
upto 8 interrupts from different sources and deliver a single combined
interrupt to the GIC. Add a node for the interrupt combiner controller
in the device tree source file.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This should help the merge with the at91 adc driver that is currently
in the staging tree.
* at91/dt:
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that the bulk of at91sam9g20-related nodes are located in at91sam9260.dtsi,
we have to re-create the path to this ADC node for SoC specific parts.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use DT_MACHINE_START() on the emev2 based KZM9D board.
Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Update the SMP glue code to use OF for matching.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is EMEV2 DT support V3. The support is limited to
whatever devices that are complied in the kernel. At this
point we have UARTs handled by "em-uart" and a timer
handled by "em-sti". Clocks and SMP are not supported.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
I got build errors with the new version now because machine_is_kzm9g is no longer
defined:
arch/arm/mach-shmobile/platsmp.c: In function 'shmobile_smp_get_core_count':
arch/arm/mach-shmobile/platsmp.c:29:2: error: implicit declaration of function 'of_machine_is_compatible'
Replace the missing function with a call to of_machine_is_compatible.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Update EXYNOS5 device tree source files for EXYNOS5250 SoC.
This includes new additions to the EXYNOS5 dtsi and SMDK5250
dts files and few minor fixes.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Changes in the dt2 branch move stuff around that gets changed
in the drivers/mmc branch. I chose a non-obvious resolution by
adding the new bus-width property into all the tegra sdhci device
nodes.
Conflicts:
arch/arm/boot/dts/tegra-cardhu.dts
arch/arm/boot/dts/tegra-harmony.dts
arch/arm/boot/dts/tegra-ventana.dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* drivers/mmc:
mmc: dt: Consolidate DT bindings
Also pulls in the omap/dt-missed-3.4 branch as a dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.
[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'kirkwood_boards_for_v3.5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
Includes an update to v3.4-rc7
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the IB-NAS6210 and IB-NAS 6220. Describe as much as
currently possible in the devicetree files, including the NAND partitions.
Use the partition scheme of the original firmware by default.
Create a board-ib62x0.c for everything else.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for Iomega Iconnect system.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Use devicetree to define NAND partitions. Use D-link partition scheme by
default, to be vaguely compatible with their userland.
Changes since last submission (V4):-
* Don't add NAND support then throw it away immediately after [Grant Likely]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add default configuration for NAND, to be enabled in your board config. Ensure
clock gating is set appropriately when the NAND is enabled.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for the DNS-320 and DNS-325. Describe as much as currently possible
in the devicetree files, create a board-dnskw.c for everything else.
Changes since last submission (V3) [Addressing comments by]:-
* One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper]
* Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely]
* Don't add NAND support then throw it away immediately after [Grant Likely]
* Describe purpose of MPP 41, 42 & 49
Changes since last submission (V2):-
* Use IEEE-compliant "okay", rather than "ok" [Scott Wood]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Use DT_MACHINE_START() on the r8a7740 based armadillo 800 eva board.
Also include a tiny DTS file to describe the board and update the
Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use DT_MACHINE_START() on the sh73a0 based KZM9G board.
Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Stephen Warren <swarren@wwwdotorg.org> writes:
This branch is based on the merge of the following branches from the
Tegra repo, which are all already pulled into arm-soc:
for-3.5/tegra30-audio
for-3.5/usb-ulpi
for-3.5/dt
... which are all based on for-3.5/gpio-pinmux
* 'for-3.5/dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The omap/dt branch adds a few instances of mmc device nodes that
need to get changed to use the common bindings. Pull that into
a new branch so we can apply the patch in a single run.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'dt' of git://github.com/hzhuang1/linux:
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
Includes an update to v3-4-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In tegra*.dtsi, set status="disable" for all HW modules that the board
design may choose not to use. Update all boards to specifically enable
any of those modules that are useful by setting status="okay".
This makes board files say which features they do use, rather than which
they don't, which feels more logical. It also makes the .dts files
slightly smaller, at least for existing content.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Put properties in order compatible, reg, interrupts, then anything else
the node has.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Sort the nodes according to the following rules:
* First, any overrides for properties or nodes created by included files,
in the order they appeared in the include file.
* Second, any nodes with a reg property, in numerical order.
* Third, any nodes without a reg property, in alphabetical order of node
name.
The second sorting rule at least will probably help if/when we need to
explicitly insert nodes for the various busses in Tegra; that will just
be an indentation change rather than also a node re-ordering.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
It's already specified in skeleton.dtsi, included via tegra20.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Place each reg "entry" on its own line, and wrap the whole list in
<> rather than each individual entry.
The convention chosen here is slightly arbitrary, but is not consistent
throughout all Tegra files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Ensure that all Tegraa GPIO specifiers contain a comment indicating which
GPIO name the number refers to.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
DT node names only need to include the unit address if it's required to
make the node name unique. Remove the unnecessary unit addresses.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Cardhu's eMMC controller is on sdhci@78000600, not sdhci@78000400.
Fix the typo. This roughly doubles the IO performance, since the
support-8bit property actually takes effect.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org # v3.4
Add device info for the core regulator tps62360 in tegra-cardhu
dts file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed node name to reflect actual device type]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds machines/boards dts{i} files for SPEAr1310 and SPEAr1340. Both
are based on ARM, Cortex A9 processor family.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Shawn Guo <shawn.guo@linaro.org> writes:
I chose to base it on Sascha's imx-common-clk series than -rc, because
otherwise it will keep patching clock file that has been removed by
imx-common-clk series. It also depends on imx-pinctrl pull-request
I just sent to be functional.
Note: when imx-common-clk and imx-pinctrl get merged together, the
following files will have conflicts. But the conflicts should not be
so hard to resolve.
[arnd: resolved those merge conflicts by pulling pinctrl branch]
* imx/dt: (24 commits)
ARM: dts: imx53-qsb: enable audio support
ARM: dts: imx51-babbage: enable audio support
ARM: imx: add audio codec clk lookup for imx53-qsb
ARM: imx: add audmux pad setting for imx51-babbage
ARM: imx: add more imx5 ssi clocks
ARM: dts: imx53-qsb: Add Dialog DA9053 PMIC support
ARM: dts: imx6q-sabrelite: add serial2 pinctrl support
ARM: dts: imx6q-sabrelite: add sound device imx6q-sabrelite-sgtl5000
ARM: imx6q_sabrelite: clk_register_clkdev cko1 for sgtl5000
ARM: imx6q: add ssi1_ipg clk_lookup
ARM: dts: imx6q-sabrelite: add audmux pinctrl support
ARM: dts: imx6q-sabrelite: add i2c1 pinctrl support
ARM: dts: imx6q-sabrelite: add audmux device
ARM: dts: imx6q-sabrelite: add ssi device
ARM: dts: imx6q-arm2: add pinctrl state for usdhc
ARM: imx6: Add UART2 for low-level debug
ARM: imx6q: register phy fixup only when CONFIG_PHYLIB is enabled
ARM: imx6q: move imx6q_sabrelite specific code to a dedicated function
ARM: dts: imx6q-sabrelite: Add SPI NOR support
ARM: dts: Add basic support for imx6q-sabresd
...
Pulls in imx/pinctrl and imx/clock as dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'mxs/dt/for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6: (51 commits)
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
ARM: dts: enable mmc for imx23-evk
mmc: mxs-mmc: add device tree support
mmc: mxs-mmc: copy wp_gpio in struct mxs_mmc_host
mmc: mxs-mmc: have dma_channel than dma_res in mxs_mmc_host
mmc: mxs-mmc: use devm_* helper to make cleanup simpler
mmc: mxs-mmc: move header from mach into linux folder
mmc: mxs-mmc: get rid of the use of cpu_is_xxx
mmc: mxs-mmc: let ssp_is_old take host as parameter
mmc: mxs-mmc: use global stmp_device functionality
ARM: mxs: add gpio support for device tree boot
gpio/mxs: add device tree probe
gpio/mxs: get rid of the use of cpu_is_xxx
gpio/mxs: use devm_* helpers to make error handling simple
ARM: mxs: add mxs-dma dt support
ARM: mxs: do not add dma device by default
dma: mxs-dma: add device tree probe support
...
All SPEAr SoC's use ST's Timer module. This patch adds device tree probing
capability for that.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It adds initial device tree support for imx23-evk board, and only
serial console is enabled.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
This patch includes basic dt support which can boot via nfs rootfs.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Add Dialog DA9053 regulators support for imx53-qsb (Loco board)
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Amit Kucheria <amit.kucheria@canonical.com>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx6qsabrelite has a sst25vf016b SPI NOR flash connected to eCSPI1.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Do not hardcode the local mac address.
Let bootloader retrieve it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It has been pointed out by device tree maintainer for several times
that the generic names 'serial' and 'ethernet' should be used for
those devices per ePAPR. Renames imx uart and fec device tree nodes
to stop them being bad examples.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove bootargs field as this information is retrieved from the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add anatop regulators to imx6q.dtsi for all imx6q platforms.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=KYD3
-----END PGP SIGNATURE-----
Merge tag 'omap-dt-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Minor DT updates based on the dt-missed-3.4 branch
By Benoit Cousson (3) and Peter Ujfalusi (2)
via Tony Lindgren
* tag 'omap-dt-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
We setup identity MMU mappings across the entire 4GB of space, which
are permissionless because the domain is set to manager.
This unfortunately allows ARMv6 and later CPUs to speculatively
prefetch from the entire address space, which can cause undesirable
side effects if those regions contain devices.
As we setup the mappings with read/write permission, we can switch
the domain to client mode, and then use the XN bit for ARMv6 and
above to control speculative prefetch to non-RAM areas.
Reported-by: R Sricharan <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This pull request updates the DaVinci SoC support to implement DEBUG_LL port
choice and optimizes the DMA ISR by removing unnecessary register reads.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=/we3
-----END PGP SIGNATURE-----
Merge tag 'v3.5-soc' of git://gitorious.org/linux-davinci/linux-davinci into next/drivers
DaVinci SoC updates for v3.5
This pull request updates the DaVinci SoC support to implement DEBUG_LL port
choice and optimizes the DMA ISR by removing unnecessary register reads.
* tag 'v3.5-soc' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
+ sync with Linux 3.4-rc6
Signed-off-by: Olof Johansson <olof@lixom.net>
By Stephen Warren (5) and Peter De Schrijver (1)
via Stephen Warren
* 'for-3.5/tegra30-audio' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
ARM: tegra: set up audio clocks for tegra30 dt
ARM: tegra: Initialize pll_p_out1
ARM: tegra: provide clock aliases for AHUB configlink
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into next/cleanup
Linux 3.4-rc6
Resolve conflict where an u5500 file had a bugfix go in, but was
deleted in the branch staged for next merge window.
Signed-off-by: Olof Johansson <olof@lixom.net>
"Jean-Christophe PLAGNIOL-VILLARD" <plagnioj@jcrosoft.com> writes:
ARM: AT91 more DT material
New SoC conversion and boards support
SoC convertion to DT:
- at91sam9260
- at91sam9263
boards:
- Atmel at91sam9g20ek/9263ek
- Calao TNY-A9260/A9263/A9G20
- Calao USB-A9260/A9263
- Ethernnut 5
- Kizbox
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91: (32 commits)
Ethernut 5 board support
ARM: at91: add kizbox board dt support.
ARM: at91: DT: add Calao TNY A9263 board support
ARM: at91: DT: add Calao USB A9263 board support
ARM: at91: add at91sam9263ek DT support
ARM: at91: add at91sam9263 DT support
ARM: at91: standard device init only if DT is not populated.
ARM: at91: DT: add Calao USB A9260 DT support
ARM: at91: Calao USB A926x factorize common binding in usb_a9260_common
ARM: at91: USB A926x update nand partition
ARM: at91: add at91sam9g20ek boards dt support
arm: at91: add Calao TNY-A9260 and TNY-A9G20 board support
ARM: at91: add at91sam9260 DT support
ARM: at91: add defconfig for device tree
ARM: at91/dt: do not specify the board any more
ARN: at91: introduce SOC_AT91xxx define to allow to compile SoC core support
ARM: at91: add SOC_AT91SAM9 kconfig option to factorise select
ARM: at91: pm select memory controler at runtime
ARM: at91: move at91_init_leds to board init
ARM: at91: do not pin mux the UARTs in init_early
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij <linus.walleij@linaro.org> writes:
this pull request contains some device tree work by Lee Jones.
I have tried to keep these patches in the arch/arm/boot/dts/*
space to get some sanity in the branch proliferation.
There is still one patch that touches arch/arm/mach-ux500 too
though (but it should merge fine with the other ux500 stuff).
The changes to the device tree are of course dependent on some
core changes and some patching in the GPIO/pin driver, but as
the device tree files are believed to be a different world
(and should one day live in their own git) I split this off
anyway. I don't think people bisect the device trees per se
and the board code in conjunction anyway.
* 'ux500-devicetree-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Configure the PRCMU Timer for db8500 based devices in DT
ARM: ux500: Enable the SMSC9115 on Snowball via Device Tree
drivers/gpio: represent gpio-nomadik as an IRQ controller in DT documentation
ARM: ux500: Rename gpio_keys in the Device Tree file
drivers/gpio: gpio-nomadik: Provide documentation for Device Tree bindings
drivers/gpio: gpio-nomadik: Device Tree bindings
ARM: ux500: Enable the external bus with Device Tree
ARM: ux500: Shorten Snowball's DT compatible gpio entry
ARM: ux500: Rename the DT compatible entry for i2c devices on Snowball
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
* spear/dt:
ARM: SPEAr3xx: Correct keyboard data passed from DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
Roland Stigge <stigge@antcom.de> writes:
this is a rearrangement of all mach-lpc32xx specific patches for device
tree conversion. Please note that:
* It builds upon the i2c-pnx changes (see previous pull request, branch
lpc32xx/i2c)
* Dave Miller gave permission to merge the lpc_eth.c change via arm-soc
(patch 1/8)
The rest of the patches is mach-lpc32xx only.
* 'lpc32xx/dt' of git://git.antcom.de/linux-2.6:
ARM: LPC32xx: Defconfig update
ARM: LPC32xx: Move common code to common.c
ARM: LPC32xx: Device tree support
ARM: LPC32xx: DTS files for device tree conversion
ARM: LPC32xx: Remove obsolete platform Kconfig
ARM: LPC32xx: clock.c registration adjustment
ARM: LPC32xx: clock.c cleanup
net: Add device tree support to LPC32xx
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a rebased version of parts of
git://git.stlinux.com/spear/linux-2.6.git spear-v3.5
which was accidentally based on the linux-next tree and mixed too
many different things. The pinctrl related changes from the same
branch are now in the spear/pinctrl branch of arm-soc.
There are a few non-DT cleanups mixed in here, but fundamentally
it's all related to the DT conversion.
* spear/dt: (9 commits)
ARM: spear: remove most mach/*.h header contents
SPEAr: Update defconfigs
SPEAr: Add PL080 DMA support for 3xx and 6xx
ARM: SPEAr3xx: Add device-tree support to SPEAr3xx architecture
SPEAr3xx: Replace printk() with pr_*()
SPEAr6xx: Add compilation support for dtbs using 'make dtbs'
SPEAr3xx: Add clock instance of usb hosts - ehci and ohci 0 and 1
SPEAr: Use CLKDEV_INIT for defining clk_lookups
ARM: SPEAr600: Change FSMC and SMI clock names
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
First part of DT changes for the Renesas shmobile platform,
pulled from:
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas.git dt
* renesas/dt:
ARM: mach-shmobile: sh7372 generic board support via DT V2
ARM: mach-shmobile: Rework sh7372 INTCS demuxer V2
ARM: mach-shmobile: Use INTC_IRQ_PINS_16H on sh7372
ARM: mach-shmobile: Use 0x3400 as INTCS vector offset
ARM: mach-shmobile: Introduce INTC_IRQ_PINS_16H
ARM: mach-shmobile: Introduce shmobile_setup_delay()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: rebuilt branch due to drop of an early merge]
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add node for the audio codec
* Enable Tegra's I2S1 controller and DAS
* Add node for top-level sound complex
Signed-off-by: Stephen Warren <swarren@nvidia.com>
According to the device's datasheet, it can support an interrupt too.
However, the existing board file doesn't specify an interrupt, and I
don't have the schematics, so I can't add an interrupts property. The
current Linux driver doesn't support anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the known i2c devices on seaboard to the i2c table.
Also rename the temperature sensor device node, and mark it as a nct1008
instead of an adt7461 (which it is -- the chips are compatible though).
Signed-off-by: Olof Johansson <olof@lixom.net>
[swarren: Removed isl29018 from patch; it's already there now. Fixed
interrupts properties now that Tegra GPIO is an interrupt controller.
Moved smart-battery to the correct I2C bus.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The I2C2 controller can be routed to either pingroup DDC or PTA. Seaboard
actually uses this as an I2C bus mux, and devices are connected to both
pingroups. This change statically assigns the I2C2 controller to pingroup
PTA, so that on-board devices can be accessed. The DDC pingroup is used
for EDID/DDC accesses which are not yet required, given the absence of
any Tegra graphics support. I2C muxing will be supported later.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This I2C bus is used for EDID/DDC reads and other "slow" I2C devices.
This requires a 100KHz SCL (clock) rate.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the device info for ALS and proximity sensor for tegra
boards cardhu, ventana and seaboard.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: s/PZ02/PZ2/ in .dts files, s/seabridge/seaboard/ in commit
description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7406/1: hotplug: copy the affinity mask when forcefully migrating IRQs
ARM: 7405/1: kexec: call platform_cpu_kill on the killer rather than the victim
ARM: 7403/1: tls: remove covert channel via TPIDRURW
ARM: 7401/1: mm: Fix section mismatches
ARM: OMAP: fix DMA vs memory ordering
ARM: 7390/1: dts: versatile-pb/ab fix MMC IRQs
ARM: 7400/1: vfp: clear fpscr length and stride bits on entry to sig handler
ARM: 7399/1: vfp: move user vfp state save/restore code out of signal.c
ARM: 7398/1: l2x0: only write to debug registers on PL310
ARM: 7397/1: l2x0: only apply workaround for erratum #753970 on PL310
ARM: 7396/1: errata: only handle ARM erratum #326103 on affected cores
Added AT91SAM9N12 SoC DT file, as well as the board definition
.dts file for AT91SAM9N12-EK.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Ensure that the USB ULPI signals are not tri-stated, and have no pull-
up or pull-down.
Ensure that the pingroup hosting the USB ULPI reset signal (GPIO PV0 or
PV1 depending on the board, so UAC) is not tri-stated, and has no pull-
up or pull-down.
This change appears larger than it is due to the grouping and sorting of
the pin configuration data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.
I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.
Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add WM8903 codec nodes, and top-level sound complex node for basic
analog audio over headset jack and internal speakers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
