The EMAC4_MR1_OBCI(freq) macro expects freg in MHz,
while opb_bus_freq is kept in Hz. Correct this.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Depending on how the 44x processors are wired, some EMAC cells
might not be useable (and not connected to a PHY). However, some
device-trees may choose to still expose them (since their registers
are present in the MMIO space) but with an "unused" property in them.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are a few variants of the STACR register that affect more than
just the "AXON" version of EMAC. Replace the current test of various
chip models with tests for generic properties in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With some PHYs, when the link goes away, the EMAC reset fails due
to the loss of the RX clock I believe.
The old EMAC driver worked around that using some internal chip-specific
clock force bits that are different on various 44x implementations.
This is an attempt at doing it differently, by avoiding the reset when
there is no link, but forcing loopback mode instead. It seems to work
on my Taishan 440GX based board so far.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It's a bad idea to call flush_scheduled_work from within a
netdev->stop because the linkwatch will occasionally take the
rtnl lock from a workqueue context, and thus that can deadlock.
This reworks things a bit in that area to avoid the problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
... since that sucker is not 32bit-only and on 64bit skb->tail is an
offset, not a pointer.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
