This converts uses dma_map_ops struct (in include/linux/dma-mapping.h)
instead of POWERPC homegrown dma_mapping_ops.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now swiotlb_pci_dma_ops is identical to swiotlb_dma_ops; we can use
swiotlb_dma_ops with any devices. This removes swiotlb_pci_dma_ops.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds max_direct_dma_addr to struct dev_archdata to remove
addr_needs_map in struct dma_mapping_ops. It also converts
dma_capable() to use max_direct_dma_addr.
max_direct_dma_addr is initialized in pci_dma_dev_setup_swiotlb(),
called via ppc_md.pci_dma_dev_setup hook.
For further information:
http://marc.info/?t=124719060200001&r=1&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Time time taken for a single cpu online operation on a pseries machine
is as follows:
Dedicated LPAR (POWER6): ~220ms.
Shared LPAR (POWER5) : ~240ms.
Of this time, approximately 200ms is taken up by __cpu_up(). This is because
we poll every 200ms to check if the new cpu has notified it's presence
through the cpu_callin_map. We repeat this operation until the new cpu sets
the value in cpu_callin_map or 5 seconds elapse, whichever comes earlier.
However, using completion_structs instead of polling loops,
the time taken by the new processor to indicate it's presence has
found to be less than 1ms on pseries. This method however may not
work on all powerpc platforms due to the time-base synchronization code.
Keeping this in mind, we could reduce msleep polling interval from
200ms to 1ms while retaining the 5 second timeout.
With this, the time taken for a cpu online operation changes as follows:
Dedicated LPAR (POWER6): 20-25ms.
Shared LPAR (POWER5) : 60-80ms.
In both these cases, it was found that the code polls through the loop
only once indicating that 1ms is a reasonable value, atleast on pseries.
The code needs testing on other powerpc platforms.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On Thu, Aug 13, 2009 at 04:14:58PM +1000, Benjamin Herrenschmidt wrote:
> On Tue, 2009-08-11 at 11:39 +0200, Bastian Blank wrote:
> > This patch just disables this driver on SMP kernels, as it is obviously
> > not supported.
> Why not remove the #error instead ? :-) I don't think it's still
> meaningful, especially since we use the timebase for delays nowadays
> which doesn't depend on the CPU frequency...
Your call. Take this one:
The build of a PowerMac 32bit kernel currently fails with
error: #warning "WARNING, CPUFREQ not recommended on SMP kernels"
Thie patch removes the not longer applicable SMP warning from the
PowerMac cpufreq code.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ptrace POKETEXT interface allows a process to modify the text pages of
a child process being ptraced, usually to insert breakpoints via trap
instructions. The kernel eventually calls copy_to_user_page, which in turn
calls __flush_icache_range to invalidate the icache lines for the child
process.
However, this function does not work on 44x due to the icache being virtually
indexed. This was noticed by a breakpoint being triggered after it had been
cleared by ltrace on a 440EPx board. The convenient solution is to do a
flash invalidate of the icache in the __flush_icache_range function.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is an attempt at cleaning up a bit the way we handle execute
permission on powerpc. _PAGE_HWEXEC is gone, _PAGE_EXEC is now only
defined by CPUs that can do something with it, and the myriad of
#ifdef's in the I$/D$ coherency code is reduced to 2 cases that
hopefully should cover everything.
The logic on BookE is a little bit different than what it was though
not by much. Since now, _PAGE_EXEC will be set by the generic code
for executable pages, we need to filter out if they are unclean and
recover it. However, I don't expect the code to be more bloated than
it already was in that area due to that change.
I could boast that this brings proper enforcing of per-page execute
permissions to all BookE and 40x but in fact, we've had that now for
some time as a side effect of my previous rework in that area (and
I didn't even know it :-) We would only enable execute permission if
the page was cache clean and we would only cache clean it if we took
and exec fault. Since we now enforce that the later only work if
VM_EXEC is part of the VMA flags, we de-fact already enforce per-page
execute permissions... Unless I missed something
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This avoids having a short glitch if the desired initial value is not
the same as what was previously in the data register.
Signed-off-by: Michael Barkowski <michaelbarkowski@ruggedcom.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When page alloc debugging is not enabled, we essentially accept any
virtual address for linear kernel TLB misses. But with kgdb, kernel
address probing, and other facilities we can try to access arbitrary
crap.
So, make sure the address we miss on will translate to physical memory
that actually exists.
In order to make this work we have to embed the valid address bitmap
into the kernel image. And in order to make that less expensive we
make an adjustment, in that the max physical memory address is
decreased to "1 << 41", even on the chips that support a 42-bit
physical address space. We can do this because bit 41 indicates
"I/O space" and thus covers non-memory ranges.
The result of this is that:
1) kpte_linear_bitmap shrinks from 2K to 1K in size
2) we need 64K more for the valid address bitmap
We can't let the valid address bitmap be dynamically allocated
once we start using it to validate TLB misses, otherwise we have
crazy issues to deal with wrt. recursive TLB misses and such.
If we're in a TLB miss it could be the deepest trap level that's legal
inside of the cpu. So if we TLB miss referencing the bitmap, the cpu
will be out of trap levels and enter RED state.
To guard against out-of-range accesses to the bitmap, we have to check
to make sure no bits in the physical address above bit 40 are set. We
could export and use last_valid_pfn for this check, but that's just an
unnecessary extra memory reference.
On the plus side of all this, since we load all of these translations
into the special 4MB mapping TSB, and we check the TSB first for TLB
misses, there should be absolutely no real cost for these new checks
in the TLB miss path.
Reported-by: heyongli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevent: Prevent dead lock on clockevents_lock
timers: Drop write permission on /proc/timer_list
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix build with older binutils and consolidate linker script
x86: Fix an incorrect argument of reserve_bootmem()
x86: add vmlinux.lds to targets in arch/x86/boot/compressed/Makefile
xen: rearrange things to fix stackprotector
x86: make sure load_percpu_segment has no stackprotector
i386: Fix section mismatches for init code with !HOTPLUG_CPU
x86, pat: Allow ISA memory range uncacheable mapping requests
- Add gpio-controller node for BCSR17, it is used to control USB
speed and VBUS;
- Add timer node for QE GTM, needed for USB host;
- Add usb node itself;
- Add some probing code for BCSR GPIOs.
NOTE: QE USB doesn't work on prototype boards, but should work on
pilot boards if specs and schematics are correct, though we
don't have the pilot boards to actually test it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add usb node;
- Configure pins and clocks;
- Enable USB function in BCSR.
The support was successfully tested using serial and ethernet gadget
drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8272_ads.c is using BCSR bits definitions from pq2ads.h, but
according to User's Guide the bits are wrong for MPC8272ADS boards
(I guess definitions from pq2ads should only be used for PQ2FADS
boards).
So, let's introduce our own definitions for MPC8272ADS, and don't
include pq2ads.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch simply adds sdhci node to the device tree.
We specify clock-frequency manually, so that eSDHC will work without
upgrading U-Boot. Though, that'll only work for default setup (1500
MHz) on new board revisions. For non-default setups, it's recommended
to upgrade U-Boot, since it will fixup clock-frequency automatically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
binutils prior to 2.17 can't deal with the currently possible
situation of a new segment following the per-CPU segment, but
that new segment being empty - objcopy misplaces the .bss (and
perhaps also the .brk) sections outside of any segment.
However, the current ordering of sections really just appears
to be the effect of cumulative unrelated changes; re-ordering
things allows to easily guarantee that the segment following
the per-CPU one is non-empty, and at once eliminates the need
for the bogus data.init2 segment.
Once touching this code, also use the various data section
helper macros from include/asm-generic/vmlinux.lds.h.
-v2: fix !SMP builds.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <sam@ravnborg.org>
LKML-Reference: <4A94085D02000078000119A5@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The earlier mpc8560 CPUs don't have the RSTCR at 0xe00b0
in the GUTS. The generic reboot code uses this tag to
determine if it should be using the RSTCR for reboot, so
remove it from the board definition.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some CPU, like the MPC8560 don't have a RSTCR in the Global
Utilities Block. These boards will implement their own reboot
call, and not use this code, so we should only warn about the
absence of the GUTS RSTCR when the default reboot code is used.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The existing fsl_rstcr_restart function is not applicable to the
mpc8560. The Global Utilities Block on this earlier CPU doesn't have
the control/reset register at 0xe00b0. This implements a board
specific reset function that uses the RCR(Reset Control Register) of
the sbc8560's EPLD to do a reset.
Signed-off-by: Liang Li <Liang.Li@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With flash partition entries in the DTS file, MTD might as well
be enabled in the defconfig. In a similar vein, enable USB and
enough related options (SCSI/ext2/ext3) so that a user can read
and write to a generic USB flash drive as well.
Also, this board only has the two default SOC UARTs, so adjust the
UART config accordingly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allows interrupts to occur on the sbc834x. Currently PCI devices
get assigned an incorrect IRQ and so the interrupt count never
increases. This was tested with the 82546GB based dual port E1000
PCI-X NIC which uses two distinct IRQ lines on the one card.
root@localhost:/root> cat /proc/interrupts | grep eth
17: 78 IPIC Level eth1
48: 27121 IPIC Level eth0
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is 8MB flash, 8kB EEPROM and 128MB SDRAM on the sbc834x
local bus, so add a localbus node in DTS with MTD partitions.
The recent U-boot commit fe613cdd4eb moves u-boot to the beginning
of flash, hence the legacy label on the partition at the end of flash.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since only one of the SoC USB devices is brought out to a physical
connector on the board, remove the 2nd (USB-DR) node from the DTS.
Having it present and USB enabled will cause a hang at boot.
Signed-off-by: Liang Li <liang.li@windriver.com>
Signed-off-by: Yang Shi <yang.shi@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MMUCSR is now defined as part of the Book-3E architecture so we
can move it into mmu-book3e.h and add some of the additional bits
defined by the architecture specs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'fixes' of git://git.marvell.com/orion:
[ARM] Orion NAND: Make asm volatile avoid GCC pushing ldrd out of the loop
[ARM] Kirkwood: enable eSATA on QNAP TS-219P
[ARM] Kirkwood: __init requires linux/init.h
This line looks suspicious, because if this is true, then the
'flags' parameter of function reserve_bootmem_generic() will be
unused when !CONFIG_NUMA. I don't think this is what we want.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: akpm@linux-foundation.org
LKML-Reference: <20090821083709.5098.52505.sendpatchset@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Initialize PCI/PCIe on the QNAP TS-119, TS-219 and TS-219P hardware
allowing the use of the discrete eSATA controller connected to the PCIe
bus in the TS-219P.
Signed-off-by: John Holland <john.holland@cellent-fs.de>
Tested-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Include linux/init.h for __init to fix this error:
CC [M] drivers/net/wireless/wl12xx/boot.o
In file included from arch/arm/mach-kirkwood/include/mach/gpio.h:13,
from arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:7,
from drivers/net/wireless/wl12xx/boot.c:24:
arch/arm/plat-orion/include/plat/gpio.h:32: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘orion_gpio_init’
make[6]: *** [drivers/net/wireless/wl12xx/boot.o] Error 1
make[5]: *** [drivers/net/wireless/wl12xx] Error 2
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
setup_arch() unconditionally sets the preferred console to ttyS.
This breaks the use of 3270 devices as the console. Provide a new
function to set the default preferred console for s390. The preferred
console depends on the conmode parameter that is used to switch
between 3270 and 3215 terminal/console mode.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As noted in 83d349f35e ("x86: don't send
an IPI to the empty set of CPU's"), some APIC's will be very unhappy
with an empty destination mask. That commit added a WARN_ON() for that
case, and avoided the resulting problem, but didn't fix the underlying
reason for why those empty mask cases happened.
This fixes that, by checking the result of 'cpumask_andnot()' of the
current CPU actually has any other CPU's left in the set of CPU's to be
sent a TLB flush, and not calling down to the IPI code if the mask is
empty.
The reason this started happening at all is that we started passing just
the CPU mask pointers around in commit 4595f9620 ("x86: change
flush_tlb_others to take a const struct cpumask"), and when we did that,
the cpumask was no longer thread-local.
Before that commit, flush_tlb_mm() used to create it's own copy of
'mm->cpu_vm_mask' and pass that copy down to the low-level flush
routines after having tested that it was not empty. But after changing
it to just pass down the CPU mask pointer, the lower level TLB flush
routines would now get a pointer to that 'mm->cpu_vm_mask', and that
could still change - and become empty - after the test due to other
CPU's having flushed their own TLB's.
See
http://bugzilla.kernel.org/show_bug.cgi?id=13933
for details.
Tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy. So
just warn if a caller gives us an empty mask, and ignore it.
This fixes a regression in 2.6.30.x, due to commit 4595f9620 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:
http://bugzilla.kernel.org/show_bug.cgi?id=13933
which causes a silent lock-up. It only seems to happen on PPro, P2, P3
and Athlon XP cores. Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's. Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.
Reported-by: Pavel Vilim <wylda@volny.cz>
Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The absence of vmlinux.lds here keeps .vmlinux.lds.cmd from being
included, which in turn leads to it and all its dependents always
getting rebuilt independent of whether they are already up-to-date.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A8D84670200007800010D31@vpn.id2.novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
gcc v4.4 currently produces this build warning:
arch/powerpc/boot/mktree.c: In function 'main':
arch/powerpc/boot/mktree.c:104: warning: dereferencing type-punned pointer will break strict-aliasing rules
tmpbuf is only used as an array of unsigned ints, so declare it that way.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently _edata does not include several data sections, this causes
the kernel's report of memory usage at boot to not match reality, and
also prevents kmemleak from working - because it scan between _sdata
and _edata for pointers to allocated memory.
This mirrors a similar change made recently to the x86 linker script.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make it possible to enable GCOV code coverage measurement on powerpc.
Lightly tested on 64-bit, seems to work as expected.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
hardirq.h on powerpc defines a __last_jiffy_stamp field, but it's not
actually used anywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As <asm/iommu.h> doesn't contain any other hardware specific definitions
but only interfaces.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Evaluate mem kernel parameter for early memory allocations. If mem is set
no allocation in the region above the given boundary is allowed. The current
code doesn't take care about this and allocate memory above the given mem
boundary.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
FUJITA Tomonori